KWG99-2001A

EXTERNAL TOP SIDE EXTERNAL BOTTOM SIDE FCC ID : KWG99-2001A

PROPOSED FCC ID. LABEL AND MARKING BOTTOM SIDE

INTERNAL TOP SIDE INTERNAL BOTTOM SIDE FCC ID : KWG99-2001A FCC ID : KWG99-2001A

KAITECH Korea Academy of Industrial Technology ( 1 / 15 ) TEST REPORT This test report only responds to the tested sample and shall not be reproduced except in full without written approval of the Korea Academy of Industrial Technology. Tested and reported by Reviewed by Soun-Kweon Seol , Senior Engineer Seok-Jin Kim , EMC Team Leader KOREA ACADEMY OF INDUSTRIAL TECHNOLOGY FG101-01-02-00 222-13, Guro-Dong Guro-Gu Seoul Korea 152-053 http://www.ktl.re.kr Ref. Report No. 99-341-006 Name and address of the applicant Car Ram Electronics Co., Ltd. 613-2 Banghwa-2Dong, Kangsue-Ku, Seoul, Korea 157-222 Standard / Test regulation FCC Part 15, Subpart C Test result Pass Incoming date : February 3, 1999 Test item(s) ; Security/Remote Control Transmitter (Car Alarm) Model/type ref. ; CA99 Manufacturer ; Car Ram Electronics Co., Ltd. Additional information ; FCC ID. : KWG99-2001A Test date : March 15, 1999 Issue date : March 30, 1999 Ref. Report No. 99 - 341 - 006 Sheet 2 of 15 Sheets TABLE OF CONTENTS . GENERAL INFORMATION ................................................................................................................... 3 1. Grantee Name and Mailing Address 2. Manufacturer's Name and Mailing Address 3. Equipment Descriptions 4. Rules and Regulations 5. Measuring Procedure 6. Place of Measurement 7. Date of Measurement . GENERAL REQUIREMENTS OF THE EUT ...................................................................................... 5 1. Labelling Requirement (Section 15.19) 2. Information to User (Sections 15.21) 3. Special Accessories (Section 15.27) 4. Compliant Conditions (Section 15.231) 5. Modification of the Equipment Under Test . INPUT POWER MEASUREMENT (Section 15.31)............................................................................. 6 . RADIATED EMISSION MEASUREMENT (Section 15.231)............................................................ 7-13 1. Test Procedure 2. Photograph for the worst case configuration 3. Sample Calculation 4. Measurement Data 5. Reference Data . OCCUPIED BANDWIDTH MEASUREMENT (Section.15.231)...................................................... 14 . TEST EQUIPMENTS USED FOR FCC COMPLIANCE TESTING................................................ 15 Ref. Report No. 99 - 341 – 006 Sheet 3 of 15 Sheets  . GENERAL INFORMATION 1. Grantee Name and : Car Ram Electronics Co.,Ltd. Mailing Address 613-2 Banghwa-2Dong, Kangsue-Ku, Seoul, Korea 157-222 2. Manufacturer's Name and : Car Ram Electronics Co.,Ltd. Mailing Address 613-2 Banghwa-2Dong, Kangsue-Ku, Seoul, Korea 157-222 3. Equipment Descriptions 3.1 Operating Frequency : 433.00MHz 3.2 Type of Emission : Pulse Code Signal 3.3 Power Supply : DC 12.0V (Battery) 3.4 Additional Information; - Oscillator used : 433.00MHz LC oscillator - I.C. used : HT6P20(HOLTEK) 4. Rules and Regulations : FCC Part 15, Subpart C 5. Measuring Procedure : ANSI C63.4-1992 6. Place of Measurement : Absorber-lined room(3-Meter) of KAITECH 7. Date of Measurement 6.1 Conducted Emission : Not Applicable 6.2 Radiated Emission : March 15, 1999 Ref. Report No. 99 - 341 - 006 Sheet 4 of 15 Sheets  . GENERAL REQUIREMENTS OF THE EUT 1. Labelling Requirement (Section 15.19) 1.1 Location on Enclosure : Manual for Installation and Operating Instruction 1.2 How Applied : Printing 2. Information to User (Section 15.21) The following or similar statements were provided in the manual for user instruction. Please refer page 19 of the attached manual for details. 3. Special Accessories (Section 15.27) 3.1 Were the special Accessories provided? [ ] yes, [ x ] no 3.2 If yes, details for the special accessories are as follows : 3.3 If yes, were the appropriate instructions provided on the first page of the text concerned with the device? [ ] yes, [ ] no 3.4 Are these accessories provided of the type which can be readily obtained from multiple retail outlets? [ ] yes, [ ] no And therefore does the manual specify what additional components or accessories are required to used in order to comply with the Rules? [ ] yes, [ ] no This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions : (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. CAUTION : Any changes or modifications in construction of this device which are not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. Ref. Report No. 99 - 341 – 006 Sheet 5 of 15 Sheets 4. Compliant Conditions (Section 15.231) 4.1 Was the EUT used for continuous transmissions, such as voice or video, and data transmission ? [ ] yes, [ x ] no 4.2 Was the EUT manually operated ? [ x ] yes, [ ] no If yes, did the EUT employ a switch that would automatically deactivate the transmitter within not more than 5 seconds of being released ? [ x ] yes, [ ] no 4.3 Was the EUT automatically activated ? [ ] yes, [ x ] no If yes, did the EUT cease transmission within 5 seconds after deactivation ? [ ] yes, [ ] no 4.4 Was the EUT used for periodic transmissions at regular predetermined intervals ? [ ] yes, [ x ] no 5. Modification of the Equipment Under Test [ x ] Any modifications were not made to the EUT during the testing since the test results were found of be complied with the FCC Rules with the EUT in the as received condition. [ ] Modification(s) was(were) made to the EUT in order to make it meet FCC Rules since it had shown non- compliance for some test items in the course of our testing. - Status of non-compliance : - Details of Modifications : Ref. Report No. 99 - 341 - 006 Sheet 6 of 15 Sheets  . INPUT POWER MEASUREMENT (Section 15.31) INPUT POWER 24.31 mW Note : 1. Input Power : P ove = (P p x D) pulse + P D Where, P p : Input Peak Power (= V x I p ) P D : Input DC Power (= V x I D ) D : Duty Cycle (= τ eff x PRF) Measured Input Voltage (V) = 12.29 DCV Measured Input Peak Cu…

Text truncated - open the document above for the full version.

TEST SETUP PHOTOS RADIATED EMISSION