KZFWMD33APIRWireless PIR Motion Dection System

INST ALLA TION A . PIR Motion Detector (T ransmitter) „ Battery Inst allation. „ Se tting the Loc a t ion The fu ncti on all o w s the user to inst a ll four (4 ) tramis tters in fo ur (4 ) d i ff erent l o ca tion s (cha nnels ) a t th e sam e ti me, an d t h e rec e i v er w i ll indicate w h ich tra n s m itt e r senses t h e motion by lightened LED (see d in Figure 7). T o set u p the l o catio n b y min i jump ers, each trans m itt e r o n l y c a n select one l o cat ion. Please refer t o Fig u re 6 t o select t h e transmitter ’ s location. „ Se tting the ID Code WMD33A provides the user 256 ID codes set up to prevent the interferences from other PIR motion detector devices in st alled next to y our house. There a r e eight ( 8 ) positions allow the user to set u p 256 ID codes (00000000 ~ 11111111 ) by mini jumpers. Please refer to Figure 6 to set up the ID Code. NOTE: [ID code] betw een the transmitter and the receiver must be the same. Code [0] = Mini jumper is on position [OFF] Code [1] = Mini jumper is on position [ON] IMPORT ANT NOTE: „ The changes o r modifications n o t exp r essl y ap proved b y the p a rt y responsible fo r compliance could void the user ’ s authority to operate the equipment. T o compl y w i th F CC R F e x posure compliance req u irement s, no ch ange to t he ante nna o r the device is permitted. An y chan ge to the ant enn a or the d e vice could result in the device exceeding the RF exposure requirement s and void user ’ s authority to operate the device. GENERAL DESCRIPTION The WMD 33A is a w i rel e ss intrusion alarm s y st e m w i th the advanced microprocessor-controlled, lo w - cur r ent PIR det ec tor incorporating an on-boa rd miniature UH F transmitter to de tect an y movem ent in a prot ected area. The W M D33A provides versatile w a ll-mou n ted PI R detector emplo y in g adjust able l ens and of fering ef ficient protectio n p a tterns for commercial and residential applications, port able alarm receiver allow s the user carr y i ng the reported alert to any w here at house if any intruder crosses or enter s any protected zone. INST ALLA TION HINTS „ Do not inst all the detector to aim at or above to the heat sources. „ Do not inst all the detector to be exposed to direct sunlight or air draf t s . „ Make sure the detection area do es not have obstructions (curt a ins, screens, p a rtitions, large pieces of furniture, plant s, etc.), w h ich may block the p a ttern of coverage. „ Prevent the locat i on of unit fr om areas that con t ain object s likely t o produce a r adiation, such as radiators, microw ave ov en, duct s , air conditioners, etc. „ Mount the unit on solid, st able surfaces. Figure 4. Four (4) “AA” batteries insertion S t ep 1. Remove unit cover and lens box (Figure 2). S t ep 2. F i nd the batter y comp ar tment on the backside of lens box . S t ep 3. Remove battery comp artment cover (Figure 3). S t ep 4. Insert four (4) “AA” batteries (not included) follow i ng the polarity diagram (Figure 4) „ W a ll Mounting Ins t a lla tion Figure 5. Place the back plate to the w a ll S t ep 1. Refer to S t ep 1. of “Battery Inst allation”. S t ep 2. Choose the desired location on the w a ll. S t ep 3. Using the screw s provided secure the back plate to the w a ll (Figure 5). NOTE: The height of w a ll mount = 2 meters above the ground B. A l arm Receiv e r 1 [POWER] It is u s ed t o in dicate the Po w e r on/o f f, B a tter y Lo w an d signal trigger . Pow e r On Flashing as (0.18s On + 2.7s Of f) Battery Low Flashing (0.14s On+0.64s Of f) Signal T r igger Flashing (0.18s On + 0.18s Of f) x 8 times 2 [CH1] ~ [CH4] As soon as P IR mot i on det ector s ense s the moti on, th e related L E D of [ C H1] ~ [CH4] will be t u rne d on. T here are four (4) PIR tr ansm i tters ma x i mum allo w e d to con nec t w ith one alarm receiv er . 3 S p eaker Door chime or alarm sound output. 4 Paper piece It is used fo r the us e r to w r ite do wn the l o cation ma nuall y w here the PIR motion detector is inst alled. 5 A ntenna It is used to ex tend the transmission dist ance. 1 W a ll-M ounting Hole It is used for w a ll-mounting. 2 Hook It is used for hangi ng th e recei v er on th e belt or w a ll, or can be the st and on the desktop. 3 Batter y c o mp ar t m ent co v e r T he cover of t he bat ter y comp artment. 4 S t and slot It is used for t he hook to slide into as the st and w hen the receiv er is put on the desktop. g [A L A R M - C H I ME -O F F ] T he selectio n switch for Al arm sound or Door Chime or Pow e r Of f the receiv er . h [HIGH-LOW - O F F ] T he sw itch for Hi gh v o lum e or Lo w v o lume or v o lume Of f. i [DC-6V] For connecting 6.0VDC pow er adapter . ID C ode Setti ng S t opper of upw ard adjustment of LENS Motion detector LENS Pow e r LED (behind the LENS) S t opper of dow nw ard adjustment of LENS Figure 1. Front V i ew of PIR Motion Detector (T ransmitter) Locati on C ode Setti ng „ Figure 2. Assembly explosion Cover LENS Box Back Plate Battery Battery Locati o n [1] Is Selected Locati on [2] Is Selected Location [3] Is Selected Location [4] Is Selected Figure 6. ID Code and Location Setting Figure 3. Battery Comp artment 4 2 THI S DEVI CE COMPLI ES W I TH P A R T 15 OF THE FCC RULES. OPERA T IONS IS SUBJEC T T O THE FOLLOW I NG T W O CONDI T I ONS: ( 1 ) THIS DEVI CE MA Y NOT CAUSE HARMFU L I N TERFERENCE AND ( 2 ) THI S D EVI CE MU ST ACCEPT ANY INTERFERENCE RECEIVED, I NCLUDI NG I N TERFEERENCE TH AT M A Y CAUSE UNDESRI E D O PERA T I O N Fr ont V i ew d c e g f Figure 7. Front V i ew of Alarm Receiv er Side V i ew Rear V i ew g h i f c e d Figure 8. Rear & Side V i ew of Alarm Rec e iv e r 5 3 1 „ Battery Inst allation Figure 9. Battery Inst allation of Alarm Receiv er Figure 10. Pull dow n the hook Figur e 1 1 . Slide the hook into the S t and Slot S t ep 1. Slide dow n the battery comp artment cover . S t ep 2. Insert four (4) “AA” batteries (not included) follow i ng the polarity diagram (Figure 9). „ Pu ttin …

Text truncated - open the document above for the full version.

910805 2 Federal Communications Commission Dear Sir: We, the undersigned, hereby authorize ELECTRONICS TESTING CENTER, TAIWAN to act on our behalf in all matters relating to application forWireless PIR Motion Detection System ( Model : WMD33A- TX, FCC ID : KZFWMD33APIR )authorization, including the signing of all documents relating to these matters. Any and all acts carried out by ELECTRONICS TESTING CENTER, TAIWAN on our behalf shall have the same effect as acts of our own. The applicant certifies that in the case of an individual applicant ( e.g., corporation ), no party to the applicant is subject to a denial of federal benefits, that includes FCC benefits, pursuant to section 5301 of the Anti-drug abuse Act of 1988, 21 U.S.C. 862. For a definition of a “party” for these purposes See 47 C.F.R. 1.2002(b).

ETC Report No.:ET92R-03-020-04 Sheet 1 of 3 Sheets FCC ID.: KZFWMD33APIR Rev. No 1.0 CONSTRUCTED PHOTOS of EUT 1. Top View of EUT

ETC Report No.:ET92R-03-020-04 Sheet 2 of 3 Sheets FCC ID.: KZFWMD33APIR Rev. No 1.0 CONSTRUCTED PHOTOS of EUT 2. Internal View of EUT 3. Internal View of EUT ETC Report No.:ET92R-03-020-04 Sheet 3 of 3 Sheets FCC ID.: KZFWMD33APIR Rev. No 1.0 CONSTRUCTED PHOTOS of EUT 4. Component View of Main PCB 5.Solder View of Main PCB

Product description The WMD33A is a wireless intrusion alarm system with the advanced microprocessor-controlled, low-current PIR detector incorporating an on-board miniature UHF transmitter to detect any movement in a protected area. The WMD33A provides versatile wall-mounted PIR detector employing adjustable lens and offering efficient protection patterns for commercial and residential applications, portable alarm receiver allows the user carrying the reported alert to anywhere in house if any intruder crosses or enters any protected zone.

Rev. No 1.0 FCC Part 15 EMI TEST REPORT of E.U.T. : Wireless PIR Motion Detection System FCC ID. : KZFWMD33APIR MODEL : WMD33A-TX Working Frequency : 314.986 MHz for APPLICANT : GOLDEN BRIDGE ELECTECH INC. ADDRESS : 3F, No. 6, LANE 270, SEC.3, PEI SHEN RD., SHEN KENG, TAIPEI TAIWAN, R.O.C. Test Performed by ELECTRONICS TESTING CENTER, TAIWAN NO. 34, LIN 5, DING FU TSUN, LINKOU HSIANG TAIPEI HSIEN, TAIWAN, R.O.C. Tel:(02)26023052 Fax:(02)26010910 http://www.etc.org.tw ; e-mail : [email protected] Report Number : ET92R-03-020-04 ETC Report No.:ET92R-03-020-04 FCC ID.: KZFWMD33APIR Rev. No 1.0 TEST REPORT CERTIFICATION Applicant : GOLDEN BRIDGE ELECTECH INC. 3F, No. 6, LANE 270, SEC.3, PEI SHEN RD., SHEN KENG, TAIPEI TAIWAN, R.O.C. Manufacturer : GOLDEN BRIDGE ELECTECH INC. 3F, No. 6, LANE 270, SEC.3, PEI SHEN RD., SHEN KENG, TAIPEI TAIWAN, R.O.C. Description of EUT : a) Type of EUT : Wireless PIR Motion Detection System b) Trade Name : ---- c) Model No. : WMD33A-TX d) FCC ID : KZFWMD33APIR e) Working Frequency : 314.986 MHz f) Power Supply : DC1.5V Battery x 4(Transmitter); Adaptor I/P: 120 VAC / 60Hz, O/P: 6VDC, 100mA(Receiver) Regulation Applied : FCC Rules and Regulations Part 15 Subpart C (2002) I HEREBY CERTIFY THAT; The data shown in this report were made in accordance with the procedures given in ANSI C63.4 and the energy emitted by the device was founded to be within the limits applicable. I assume full responsibility for accuracy and completeness of these data. Note : 1. The results of the testing report relate only to the items tested. 2. The testing report shall not be reproduced except in full, without the written approval of ETC. Issued Date : Apr. 08, 2003 Test Engineer : ( Mick Chen ) Approve & Authorized Signer : Will Yauo, Manager EMC Dept. II of ELECTRONICS TESTING CENTER, TAIWAN ETC Report No.:ET92R-03-020-04 FCC ID.: KZFWMD33APIR Rev. No 1.0 Table of Contents Page 1. GENERAL INFORMATION.....................................................................................................................................................1 1.1 PRODUCT DESCRIPTION...........................................................................................................................................................1 1.2 CHARACTERISTICS OF DEVICE:...............................................................................................................................................1 1.3 TEST METHODOLOGY..............................................................................................................................................................1 1.4 TEST FACILITY..........................................................................................................................................................................1 2. DEFINITION AND LIMITS.......................................................................................................................................................2 2.1 DEFINITION................................................................................................................................................................................2 2.2 RESTRICTED BANDS OF OPERATION.....................................................................................................................................2 2.3 LIMITATION...............................................................................................................................................................................2 2.4 LABELING REQUIREMENT.......................................................................................................................................................4 2.5 USER INFORMATION.................................................................................................................................................................4 3 SYSTEM TEST CONFIGURATION.........................................................................................................................................5 3.1 JUSTIFICATION..........................................................................................................................................................................5 3.2 DEVICES FOR TESTED SYSTEM...............................................................................................................................................5 4. RADIATED EMISSION MEASUREMENT.............................................................................................................................6 4.1 APPLICABLE STANDARD.........................................................................................................................................................6 4.2 MEASUREMENT PROCEDURE..................................................................................................................................................6 4.3 TEST DATA.................................................................................................................................................................................8 4.3.1 314 MHz............................................................................................................................................................................8 4.3.2 Other Emissions...............................................................................................................................................................9 4.4 FIELD STRENGTH CALCULATION........................................................................................................................................10 4.5 ACTIVATE TIME......................................................................................................................................................................10 4.6 CALCULATION OF DUTY FACTOR..................................................................................................................…

Text truncated - open the document above for the full version.

ETC Report No.:ET92R-03-020-04 Sheet 12 of 21 Sheets FCC ID.: KZFWMD33APIR Rev. No 1.0 4.9 Radiated Measurement Photos