L9G766510RC Car

(IF APPLICABLE) Warning: Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. Radio Controled Vehicle Full Function Car Series Scale: 1:16 MCS: 9V BACKWARD FORWARD STOP ® R L VEHICLE Removal of the battery cover will again require a "phillips head" screwdriver. Turn the lock tab and remove the cover. See Figure 3. Make sure the 7.2V Ni-Cd has a full charge as per the charging instructions. Connect the battery wires to the vehicle being sure that the lock tab snaps over the raised ridge. Place the battery in the battery compartment being sure that wires are on space under the battery. See Figure 4. Replace the battery cover, and secure with the screw that was previously removed. SPEED CONTROL JOYSTICK STEERING CONTROL JOYSTICK TELESCOPIC ANTENNA Figure 1 Figure 7 Figure 10 Figure 11 Figure 9 3. Start operating by moving speed control joysticks on the left forward.See Figure 7. 4. Release both control joysticks, the vehicle will stop. See Figure 8. 5. Vehicle steering is controlled by joystick on right by moving left or right .See Figure 9. 6. Do not let vehicle get out of transmitting range as you will then have no control. This range varies due to surroundings. 7. When finished, turn all switches to off position and remove all batteries. Vehicle operation varies from 35 to 45 minutes depending on how the car is used, and the age of the batteries. INSTALLING BATTERIES INSTALLING THE BATTERIES TRANSMITTER Removal of the battery cover requires a "phillips head" screwdriver.See Figure 1. After removing this screw, slide the cover downward to remove. Place the 9 V battery in position so that the (+) and (-) are in the proper alignment ads noted.Replace screw to battery cover. See Figure 2. . OPERATING R/C CAR IMPORTANT! • Do not use vehicle in mud, water, snow, or sand. • Do not play with vehicle in the street. • Do not crash vehicle into any object at high speeds. • When the vehicle slows down install new or freshly charged batteries. • Clean the vehicle with a damp paper towel after operating. (Do not use any chemicals to wipe off car) • Do not leave vehicle in direct sunlight for lengthy periods. OPERATING CAR 1. Turn the car switch to "ON". (Located on bottom of car) See Figure 5. 2. Screw the antenna on the top of the transmitter and extend to full length. See Figure 6. THINGS YOU SHOULD KNOW • Radio interference can cause your car to react strangely. • Another vehicle operating on the same frequency can disrupt your controlling the vehicle. • CB's, cellular telephones, two way radios, and other transmitting devices, and high tension wires may cause interference with operation. • Your vehicle can sometimes cause interference with television or even radio reception. Move to another area if you notice this occurrence. WHEEL ALIGNMENT Your steering can be adjusted with the trim switch located on the bottom chassis area. Turn either left or right until you have made the adjustment to maintain a straight path of movement. See Figure 10. Transmitter : 9V --- 0.05A NATURE POWER OF SUPPLY Receiver : 7.2V --- 2.5A CHARGING THE BATTERY • Plug charger into a standard household outlet (110/120 Volt). See Figure 11. • Join together the plug from the battery to the receptacle plug attached to the charger wires. Be sure to get a firm fit by having the ridge snap into place with the clip.See Figure 11. • Allow battery to charges for 6-8 hours for a complete and full charge. Additional charging will not improve your battery's output, and could eventual damage the battery. Do not charge a battery if you notice it leaking or see corrosion on any part of the battery. • A characteristic of Ni-Cd batteries is a loss of power quickly. A spare battery is therefore recommended for longer play, and happier operators. • If the battery is hot after operation please wait until it is cool before recharging. Attempting to recharge a battery in this condition can reduce the life of the battery and maybe cause damage later. • The rechargeable battery must be charged with the recommended battery charger. • The battery charger is not a toy. • The battery charger is to be regularly examined for damage to the cord, plug enclosure and other parts, in the event of such damage; the rechargeable batteries must not be used with this battery charger until the damage has been repaired. IMPORTANT! • Do not leave batteries in the vehicle or the transmitter when the toy is not in use. • Do not use old and new batteries together. • Do not mix different types of batteries. Only batteries of the same or equivalent type as recommended are to be used.(e .g. alkaline,Ni-Cd rechargeable, and manganese, or other non-alkaline batteries) • Dispose of old batteries in the proper manner ; do not burn or place near fire. • Non-rechargeable batteries are not to be recharged. • The supply terminals are not to be short-circuited. • Not suitable for children under 3 years of age due to small parts. • Remove rechargeable batteries from the unit before recharging. • Recharging of rechargeable batteries should only be done under adult supervision. • The screwdriver is not a toy. • Do not give the screwdriver to children. • Change the car body by adult only. • Exhausted batteries are to be removed from the toy. BATTERY REQUIREMENTS • This vehicle requires a 7.2V Ni-Cd battery and one 9V (6LR61) (alkaline) (6F22) (carbon zinc) battery for the transmitter. Figure 8 Figure 2 Figure3Figure 4 Figure5Figure 6

FCC ID: L9G766510 Ophoto1 Ophoto2 FCC ID: L9G766510 Ophoto3 Ophoto4

FCC ID: L9G766510 Iphoto1 Iphoto2 FCC ID: L9G766510 Iphoto3 Iphoto4

FCC ID: L9G766510 Technical Description : The brief circuit description is listed as follows : - X1, Q2 and associated circuit act as 27.145 MHz Oscillator. - Q1 and associated circuit act as Modulator. - IC1 and associated circuit act as Encoder. - SW1, SW2 and associated circuit act as Control Key. Antenna Used : An extendable antenna has been used.

55 44 33 22 11 D D C C B B A A VCC VCC Title Size Document Number Rev Date: Sheet of 01 Remote Control Transmitter 27 Tx 1 1 ARTIN Industrial Co.,Ltd. TRANSMITTER 27.145Mhz (PCB ST-8706) A4 Monday, May 23, 2005 X:\ARTIN\EDDY VR&D 050316\MCS PN\RC CAR\317001020.DSN 12-11-1999 MCS: 317001020 Title Size Document Number Rev Date: Sheet of 01 Remote Control Transmitter 27 Tx 1 1 ARTIN Industrial Co.,Ltd. TRANSMITTER 27.145Mhz (PCB ST-8706) A4 Monday, May 23, 2005 X:\ARTIN\EDDY VR&D 050316\MCS PN\RC CAR\317001020.DSN 12-11-1999 MCS: 317001020 Title Size Document Number Rev Date: Sheet of 01 Remote Control Transmitter 27 Tx 1 1 ARTIN Industrial Co.,Ltd. TRANSMITTER 27.145Mhz (PCB ST-8706) A4 Monday, May 23, 2005 X:\ARTIN\EDDY VR&D 050316\MCS PN\RC CAR\317001020.DSN 12-11-1999 MCS: 317001020 Note: 1. All resistance values are indicated in "ohm" (Mohm=1,000Kohm ; Kohm=1,000 ohm) 2. All capacitance values are indictaed in "uF" (uF=1,000nF ; nF=1,000pF)
         ! Q1 2SC1815 Q1 2SC1815 Q2 2SC1815 Q2 2SC1815 C547PC547P L14.7uHL14.7uH C7 45P C7 45P X1 27.145MHz X1 27.145MHz 150 R3 150 R3 C4 300P C4 300P C2 82P C2 82P C12 0.04 C12 0.04 300 R1 300 R1 SW1SW1 330 R7 330 R7 390K R5 390K R5 D1 IN4148 D1 IN4148 C8 0.04 C8 0.04 Z1 3.9V Z1 3.9V L4 1.8uH L4 1.8uH L2 10.5T L2 10.5T R 1 TESTB 2 GND 3 B 4 F 5 T 6 SC 7 VDD 9 PC 10 SO 8 OSCO 11 OSCI 12 FOSC 13 L 14 IC1 TX2 IC1 TX2 L3 L2702 L3 L2702 C1 150P C1 150P C6 47P C6 47P C368PC368P 30K R4 30K R4 300K R6 300K R6 SW2SW2 9V9V

• The test results reported in this report shall refer only to the sample actually tested and shall not refer or be deemed to refer to bulk from which such a sample may be said to have been obtained. • This report shall not be reproduced except in full without prior authorization from Intertek Testing Services Hong Kong Limited. • The evaluation data of the report will be kept for 3 years from the date of issuance. FCC ID : L9G766510 Artin Industrial Company Limited Application For Certification (FCC ID: L9G766510) Transmitter Sample Description : Remote Control Car (27MHz) TX Model : 708005 We hereby certify that the sample of the above item is considered to comply with the requirements of FCC Part 15, Subpart C for Intentional Radiator, mention 47 CFR [12-8-2003] 0508007 BC/at May 26, 2005 INTERTEK TESTING SERVICES FCC ID: L9G766510 i LIST OF EXHIBITS INTRODUCTION EXHIBIT 1 : General Description EXHIBIT 2 : System Test Configuration EXHIBIT 3 : Emission Results EXHIBIT 4 : Equipment Photographs EXHIBIT 5 : Product Labelling EXHIBIT 6 : Technical Specifications EXHIBIT 7 : Instruction Manual EXHIBIT 8 : Miscellaneous Information INTERTEK TESTING SERVICES FCC ID: L9G766510 ii MEASUREMENT/TECHNICAL REPORT Artin Industrial Company Limited - MODEL: 708005 FCC ID: L9G766510 May 26, 2005 This report concerns (check one:) Original Grant X Class II Change Equipment Type: Low Power Transmitter (example: computer, printer, modem, etc.) Deferred grant requested per 47 CFR 0.457(d)(1)(ii)? Yes No X If yes, defer until: date Company Name agrees to notify the Commission by: date of the intended date of announcement of the product so that the grant can be issued on that date. Transition Rules Request per 15.37? Yes No X If no, assumed Part 15, Subpart C for intentional radiator - the new 47 CFR [12-8- 2003 Edition] provision. Report prepared by: Billy Chow Intertek Testing Services 2/F., Garment Center, 576, Castle Peak Road, HONG KONG Phone: 852-2173-8502 Fax: 852-2742-9149 INTERTEK TESTING SERVICES FCC ID: L9G766510 iii Table of Contents 1.0 General Description................................................................................................ 2 1.1 Product Description............................................................................................. 2 1.2 Related Submittal(s) Grants................................................................................. 2 1.3 Test Methodology................................................................................................ 3 1.4 Test Facility ......................................................................................................... 3 2.0 System Test Configuration..................................................................................... 5 2.1 Justification.......................................................................................................... 5 2.2 EUT Exercising Software ..................................................................................... 5 2.3 Special Accessories ............................................................................................ 5 2.4 Equipment Modification ....................................................................................... 6 2.5 Support Equipment List and Description.............................................................. 6 3.0 Emission Results .................................................................................................... 8 3.1 Field Strength Calculation.................................................................................... 9 3.1 Field Strength Calculation (cont’d)..................................................................... 10 3.2 Radiated Emission Configuration Photograph .................................................... 11 3.3 Radiated Emission Data .................................................................................... 12 4.0 Equipment Photographs ....................................................................................... 15 5.0 Product Labelling .................................................................................................. 17 6.0 Technical Specifications....................................................................................... 19 7.0 Instruction Manual ................................................................................................ 21 8.0 Miscellaneous Information................................................................................... 23 8.1 Measured Bandwidth......................................................................................... 24 8.2 Discussion of Pulse Desensitization................................................................... 25 8.3 Calculation of Average Factor............................................................................ 26 8.4 Emission Test Procedures ................................................................................ 27 8.4 Emission Test Procedures (Cont’d).................................................................... 28 INTERTEK TESTING SERVICES FCC ID: L9G766510 iv List of attached file Exhibit type File Description filename Test Report Test Report report.pdf Operation Description Technical Description descri.pdf Test Setup Photo Radiated Emission radiated photos.doc Test Report Bandwidth Plot bw.pdf External Photo External Photo external photos.doc Internal Photo Internal Photo internal photos.doc Block Diagram Block Diagram block.pdf Schematics Circuit Diagram circuit.pdf ID Label/Location Label Artwork and Location label.pdf User Manual User Manual manual.pdf Test Report Average Factor af.pdf INTERTEK TESTING SERVICES FCC ID: L9G766510 1 EXHIBIT 1 GENERAL DESCRIPTION INTERTEK TESTING SERVICES FCC ID: L9G766510 2 1.0 General Description 1.1 Product Description The equipment under test (EUT) is a transmitter for a RC Car operating at 27.145 MHz which is controlled by a crystal. The EUT is powered by a 9V b…

Text truncated - open the document above for the full version.

INTERTEK TESTING SERVICES Front View Back View