LY5-PCIABUIAndroid Based UI

Pitney Bowes Android Based User Interface (PB AB UI) User Manual PCI Private Limited 35 Pioneer Road North Singapore 628475 Copyright © 2020 PCI Private Limited. All rights reserved. PCI Private Limited is a trademark of PCI Private Limited. All other trademarks are the property of their respective owners. PCI Private Limited endeavours to ensure that the information in this document is correct and fairly stated, but PCI Private Limited is not liable for any errors or omissions. Published information may not be up to date, and it is important to confirm current status with PCI Private Limited. This technical data may be subject to U.S. and international export, re-export or transfer (export) laws. Diversion contrary to U.S. and international law is strictly prohibited. March 2020 1. Component Overview 2. FCC, IC and CE Compliance Statements 3. Installation Planning Component Overview Pitney Bowes Android Based User Interface (PB AB UI) Characteristics Requirements Conditions Operating Temperature +10° C to +50° C (50° F to 122° F) Operating Voltage 5 Volts DC Operating Current 2A max @ 5V Connector Pinouts 2-pin Barrel DC Jack 5-pin Micro USB Connector Pin # Function 1 VUSB 2 D- 3 D+ 4 ID 5 GND The PB AB UI unit has no user-serviceable parts. The device is for the printer using only. Proper recycling or disposal per local law is required for all components of the PB AB UI. FCC Compliance Statement This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in an industrial installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures: - Reorient or relocate the receiving antenna. - Increase the separation between the equipment and receiver. - Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. - Consult the dealer or an experienced radio/TV technician for help. FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. This device meets all the other requirements specified in Part 15E, Section 15.407 of the FCC Rules. Radiation Exposure Statement: This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance of 20cm between the radiator & your body. Note: The country code selection is for non-US model only and is not available to all US model. Per FCC regulation, all WiFi product marketed in US must be fixed to US operation channels only. IC Compliance Statement This device complies with ISED’s licence-exempt RSSs. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Le présent appareil est conforme aux CNR d’ ISED applicables aux appareils radio exempts de licence. L’exploitation est autorisée aux deux conditions suivantes : (1) le dispositif ne doit pas produire de brouillage préjudiciable, et (2) ce dispositif doit accepter tout brouillage reçu, y compris un brouillage susceptible de provoquer un fonctionnement indésirable. Caution : (i) the device for operation in the band 5150-5250 MHz is only for indoor use to reduce the potential for harmful interference to co-channel mobile satellite systems; (ii) where applicable, antenna type(s), antenna models(s), and worst-case tilt angle(s) necessary to remain compliant with the E.I.R.P. elevation mask requirement set forth in section 6.2.2.3 shall be clearly indicated. Avertissement: Le guide d’utilisation des dispositifs pour réseaux locaux doit inclure des instructions précises sur les restrictions susmentionnées, notamment : (i) les dispositifs fonctionnant dans la bande 5150-5250 MHz sont réservés uniquement pour une utilisation à l’intérieur afin de réduire les risques de brouillage préjudiciable aux systèmes de satellites mobiles utilisant les mêmes canaux; (ii) lorsqu’il y a lieu, les types d’antennes (s’il y en a plusieurs), les numéros de modèle de l’antenne et les pires angles d’inclinaison nécessaires pour rester conforme à l’exigence de la P.I.R.E. applicable au masque d’élévation, énoncée à la section 6.2.2.3, doivent être clairement indiqués Radiation Exposure Statement: This equipment complies with ISED radiation exposure limits set forth for an uncontrolled environment. This equipment must be installed and operated with greater than 20cm between the radiator & your body. Déclaration d'exposition aux radiations: Cet équipement est conforme aux limites d'exposition aux rayonnements ISED établies pour un environnement non contrôlé. Cet équipement doit être installé et utilisé à plus de 20 cm entre le radiateur et votre corps. CE Compliance Statement This device complies with Directive 2014/53/EU issued by the Commission of the European Community. A minimum separation distance of 20 cm must be m…

Text truncated - open the document above for the full version.

FCC, Request for non-disclosure Date: 19-Oct-10 RF_501, Issue 7 Page 1 of 1 Company Name: PCI Private Limited Address: 35 Pioneer Road North City: Singapore Country: Singapore To: Telefication B.V., Dept. FCC TCB Edisonstraat 12A 6902 PK ZEVENAAR The Netherlands Request for confidentiality Subject: Request for confidentiality FCC ID: LY5-PCIABUI Reference number: ###### Dear FCC TCB, 1. Long-Term Confidentiality Pursuant to 47 CFR Section 0.459(a) & (b), we hereby request non-disclosure and confidential treatment of the following materials submitted in support of FCC certification application: Bill(s) of Material Block Diagrams Operational Description Schematic Diagrams Tune-up Procedure Above materials contain secrets, proprietary and technical information, which would customarily be guarded from competitors under 47 CFR, section 0.457(d)(2). Disclosure or publication or any portion of this company confidential material to other parties could cause substantial competitive harm and provide unjustified benefits for competitors. 2. Short-Term Confidentiality (STC) Pursuant to Public Notice DA 04-1705 of the Commission’s policy, in order to comply with the marketing regulations in 47 CFR §2.803 and the importation rules in 47 CFR §2.1204, a pplicant hereby requests Short-Term Confidential treatment of the following materials (note 1): Internal Photos User’s Manual Test Set-up Photos External Photos Planned Release Date STC: 180 days from initial date of certification Date: 25 March 2020 Name and signature of applicant: Josielyn V. Mendoza / Manager, Quality Assurance System Notes: 1) A document or type of document can only have ONE type of confidentiality! 2) Short-Term confidentiality is in principle for 45 days from date of grant; it can be extended max 3 times (total time 180 days max.)! 3) FCC must be informed when marketing begins earlier. 4) Release takes place automatically thus extension must be requested in time. Telefication does not remind you of this! 5) Request for extension or for release must be received by Telefication at least 7 days before date of actual marketing or before expiration of the STC period

Report No：2020009R-RFUSP01V01 Page: 127 of 144 Attachment 2  EUT External Photograph (1) EUT Photo (2) EUT Photo Report No：2020009R-RFUSP01V01 Page: 128 of 144 (3) EUT Photo (4) EUT Photo Report No：2020009R-RFUSP01V01 Page: 129 of 144 (5) EUT Photo (6) EUT Photo

MADE IN INDONESIA FABRIQUÉ EN INDONÉSIE HECHO EN INDONESIA MODEL NO.: CSD-ELINK2 HZ84007 ANDROID BASED UI P2Y7WW000000 MAC 00:X0:XX:0X:X0:00 FCC : LY5-PCIABUI CAN ICES-3(B)/NMB-3(B) IC : 5113A-PCIABUI XXX-ABCDEF - - 0.15 0.2 2:1 LABEL, PRODUCT ID PRINTING PITNEY BOWES PBLB001101-PRN 1 1 19-FEB-20 J. SAYSON T NATHAN J. SAYSON 19-FEB-20 INITIAL ISSUEX1

Report No：2020009R-RFUSP01V01 Page: 130 of 144 Attachment 3  EUT Internal Photograph (1) EUT Photo (2) EUT Photo Report No：2020009R-RFUSP01V01 Page: 131 of 144 (3) EUT Photo (4) EUT Photo Report No：2020009R-RFUSP01V01 Page: 132 of 144 (5) EUT Photo (6) EUT Photo Report No：2020009R-RFUSP01V01 Page: 133 of 144 (7) EUT Photo Report No：2020009R-RFUSP01V01 Page: 134 of 144 (8) EUT Photo (Antenna) (9) EUT Photo (Antenna) Report No：2020009R-RFUSP01V01 Page: 135 of 144 (10) EUT Photo (11) EUT Photo Report No：2020009R-RFUSP01V01 Page: 136 of 144 (12) EUT Photo (13) EUT Photo Report No：2020009R-RFUSP01V01 Page: 137 of 144 (14) EUT Photo (15) EUT Photo Report No：2020009R-RFUSP01V01 Page: 138 of 144 (16) EUT Photo (17) EUT Photo Report No：2020009R-RFUSP01V01 Page: 139 of 144 (18) EUT Photo (19) EUT Photo Report No：2020009R-RFUSP01V01 Page: 140 of 144 (20) EUT Photo (21) EUT Photo Report No：2020009R-RFUSP01V01 Page: 141 of 144 (22) EUT Photo (23) EUT Photo Report No：2020009R-RFUSP01V01 Page: 142 of 144 (24) EUT Photo (25) EUT Photo Report No：2020009R-RFUSP01V01 Page: 143 of 144 (26) EUT Photo (27) EUT Photo Report No：2020009R-RFUSP01V01 Page: 144 of 144 (28) EUT Photo

Report No. 2020009R-RFUSP02V00-A Page: 1 of 11 RF Exposure Evaluation Declaration Product Name ：Android Based UI Trade Name ：PCI Model No. ：CSD-ELINK2 FCC ID ：LY5-PCIABUI Applicant : PCI Private Limited Address : 35 Pioneer Road North, Singapore 628475 Singapore Date of Receipt : Feb. 03, 2020 Date of Declaration : Mar. 17, 2020 Report No. : 2020009R-RFUSP02V00-A Report Version : V1.0 The declaration results relate only to the samples calculated. The declaration shall not be reproduced except in full without the written approval of DEKRA Testing and Certification Co., Ltd.. Report No. 2020009R-RFUSP02V00-A Page: 2 of 11 RF Exposure Evaluation Declaration Issued Date : Mar. 17, 2020 Report No. : 2020009R-RFUSP02V00-A Product Name : Android Based UI Applicant : PCI Private Limited Address : 35 Pioneer Road North, Singapore 628475 Singapore Manufacturer : PCI Private Limited Address : 35 Pioneer Road North, Singapore 628475 Singapore Trade Name : PCI Model No. : CSD-ELINK2 FCC ID : LY5-PCIABUI Applicable Standard : FCC 47 CFR Part 2.1091 Radiofrequency radiation exposure evaluation: mobile devices. Test Lab : Hsin Chu Laboratory Address : No.372-2, Sec. 4, Zhongxing Rd., Zhudong Township, Hsinchu County 310, Taiwan, R.O.C. TEL: +886-3-582-8001 / FAX: +886-3-582-8958 Test Result : Complied Tested By : ( Rueyyan Lin / Senior Engineer ) Approved By : ( Louis Hsu / Deputy Manager ) Report No. 2020009R-RFUSP02V00-A Page: 3 of 11 Revision History Report No. Version Description Issued Date 2020009R-RFUSP02V00-A V1.0 Initial issue of report Mar. 17, 2020 Report No. 2020009R-RFUSP02V00-A Page: 4 of 11 1.1. Test Facility Ambient conditions in the laboratory: Items Test Item Required (IEC 68-1) Actual Test Site Temperature (°C) Peak Output Power 15 - 35 20 3 Humidity (%RH) 25 - 75 50 Note: Test site information refers to Laboratory Information. Laboratory Information The address and introduction of DEKRA Testing and Certification Co., Ltd. laboratories can be founded in our Web site: http://www.dekra.com.tw If you have any comments, please don’t hesitate to contact us. Our test sites as below: Test Laboratory DEKRA Testing and Certification Co., Ltd. Address 1. No. 75-2, 3rd Lin, WangYe Keng, Yonghxing Tsuen, Qionglin Shiang, Hsinchu County 307, Taiwan, R.O.C. 2. No.372, Sec. 4, Zhongxing Rd., Zhudong Township, Hsinchu County 31061, Taiwan, R.O.C. 3. No.372-2, Sec. 4, Zhongxing Rd., Zhudong Township, Hsinchu County 31061, Taiwan, R.O.C. Phone number 1. +886-3-592-8858 2. +886-3-582-8001 3. +886-3-582-8001 Fax number 1. +886-3-592-8859 2. +886-3-582-8958 3. +886-3-582-8958 Email address [email protected] Website http://www.dekra.com.tw Report No. 2020009R-RFUSP02V00-A Page: 5 of 11 1.2. List of Test Equipment Peak Output Power / SR10-H Instrument Manufacturer Model No. Serial No. Cal. Date Next Cal. Date High Speed Peak Power Meter Dual Input Anritsu ML2496A 1602004 2019/12/02 2020/12/01 Pulse Power Sensor Anritsu MA2411B 1531043 2019/12/02 2020/12/01 Pulse Power Sensor Anritsu MA2411B 1531044 2019/12/02 2020/12/01 Power Meter Keysight 8990B MY510002482019/05/21 2020/05/20 Power Sensor Keysight N1923A MY572400052019/05/21 2020/05/20 Note: All equipment upon which need to calibrated are with calibration period of 1 year. 1.3. Uncertainty Test item Uncertainty Peak Output Power ± 2.26 dB Determining compliance shall be based on the results of the compliance measurement, not taking into account measurement instrumentation uncertainty. Report No. 2020009R-RFUSP02V00-A Page: 6 of 11 2. RF Exposure Evaluation 2.1. Limits According to FCC 1.1310: The criteria listed in the following table shall be used to evaluate the environment impact of human exposure to radio frequency (RF) radiation as specified in 1.1307(b) LIMITS FOR MAXIMUM PERMISSIBLE EXPOSURE (MPE) Frequency Range (MHz) Electric Field Strength (V/m) Magnetic Field Strength (A/m) Power Density (mW/cm2) Average Time (Minutes) (A) Limits for Occupational/ Control Exposures 300-1500 -- -- F/300 6 1500-100,000 -- -- 5 6 (B) Limits for General Population/ Uncontrolled Exposures 300-1500 -- -- F/1500 6 1500-100,000 -- -- 1 30 F= Frequency in MHz RF Field Strength Limits for Controlled Use Devices (Controlled Environment) Frequency Range (MHz) Electric Field (V/m rms) Magnetic Field (A/m rms) Power Density (W/m2) Reference Period (minutes) 0.003-1023 170 180 - Instantaneous* 0.1-10 - 1.6/ ƒ - 6** 1.29-10 193/ ƒ 0.5 - - 6** 10-20 61.4 0.163 10 6 20-48 129.8/ ƒ 0.25 0.3444/ ƒ 0.25 44.72/ ƒ 0.5 6 48-100 49.33 0.1309 6.455 6 100-6000 15.60 ƒ 0.25 0.04138 ƒ 0.25 0.6455ƒ0.5 6 6000-15000 137 0.364 50 6 15000-150000 137 0.364 50 616000/ ƒ 1.2 150000-300000 0.354 ƒ 0.5 9.40 x 10-4 ƒ 0.5 3.33 x 10-4 ƒ 616000/ ƒ 1.2 Note: ƒ is frequency in MHz. *Based on nerve stimulation (NS). ** Based on specific absorption rate (SAR). Report No. 2020009R-RFUSP02V00-A Page: 7 of 11 Friis Formula Friis transmission formula: Pd = (Pout*G)/(4*pi*r 2 ) Where Pd = power density in mW/cm 2 Pout = output power to antenna in mW G = gain of antenna in linear scale Pi = 3.1416 R = distance between observation point and center of the radiator in cm Pd id the limit of MPE, 1 mW/cm 2 . If we know the maximum gain of the antenna and the total power input to the antenna, through the calculation, we will know the distance r where the MPE limit is reached. 2.2. Test Procedure Software provided by client enabled the EUT to transmit and receive data at lowest, middle and highest channel individually. Report No. 2020009R-RFUSP02V00-A Page: 8 of 11 2.3. Test Result of RF Exposure Evaluation Product Android Based UI Test Mode Transmit Mode Test Condition RF Exposure Evaluation Antenna Gain: The maximum antenna gain is 3.59dBi. Output Power into Antenna & RF Exposure Evaluation Distance: WLAN Function 2.4GHz Band Mode Frequency (MHz) Conducted Output Power Power Density at R = 20cm (mW/cm 2 ) Limit (mW/cm 2 ) dBm mW 802.11b 2412 12.290 16.943 0.008 1 2437 14.350 27.227 0.012 1 2462 16.360 43.251 0.020 1 8…

Text truncated - open the document above for the full version.

Report No： 2020009R-RFUSP02V00 Page: 1 of 142 FCC Test Report Product Name：Android Based UI Trade Name ：PCI Model No. ：CSD-ELINK2 FCC ID. ：LY5-PCIABUI Applicant ： PCI Private Limited Address ： 35 Pioneer Road North, Singapore 628475 Singapore Date of Receipt：Feb. 03, 2020 Issued Date ：Mar. 17, 2020 Report No. ：2020009R-RFUSP02V00 Report Version ：V1.0 The test results relate only to the samples tested. The test report shall not be reproduced except in full without the written approval of DEKRA Testing and Certification Co., Ltd.. Report No： 2020009R-RFUSP02V00 Page: 2 of 142 Test Report Certification Issued Date : Mar. 17, 2020 Report No. : 2020009R-RFUSP02V00 Product Name ： Android Based UI Applicant ： PCI Private Limited Address ： 35 Pioneer Road North, Singapore 628475 Singapore Manufacturer ： PCI Private Limited Address ： 35 Pioneer Road North, Singapore 628475 Singapore Trade Name ： PCI Model No. ： CSD-ELINK2 FCC ID. ： LY5-PCIABUI EUT Test Voltage ： DC 5V Testing Voltage ： DC 5V Applicable Standard： FCC CFR Title 47 Part 15 Subpart C Section 15.247: 2018 ANSI C63.10: 2013 Laboratory Name ： Hsin Chu Laboratory Address ： No.372-2, Sec. 4, Zhongxing Rd., Zhudong Township, Hsinchu County 310, Taiwan, R.O.C. TEL: +886-3-582-8001 / FAX: +886-3-582-8958 Test Result ： Complied Documented By : ( Carol Tsai / Senior Engineering Adm. Specialist ) Tested By : ( Rueyyan Lin / Senior Engineer ) Approved By : ( Louis Hsu / Deputy Manager ) Report No： 2020009R-RFUSP02V00 Page: 3 of 142 Revision History Report No. Version Description Issued Date 2020009R-RFUSP02V00 V1.0 Initial issue of report Mar. 17, 2020 Report No： 2020009R-RFUSP02V00 Page: 4 of 142 TABLE OF CONTENTS Description Page 1. General Information ...................................................................................................................... 6 1.1. EUT Description ................................................................................................................ 6 1.2. Test Mode .......................................................................................................................... 9 1.3. Tested System Details ..................................................................................................... 10 1.4. Configuration of tested System ....................................................................................... 10 1.5. EUT Exercise Software ................................................................................................... 10 1.6. Test Facility ..................................................................................................................... 11 1.7. List of Test Equipment ..................................................................................................... 13 1.8. Duty Cycle ....................................................................................................................... 16 1.9. Uncertainty ...................................................................................................................... 18 2. Conducted Emission ................................................................................................................... 19 2.1. Test Setup ....................................................................................................................... 19 2.2. Limits ............................................................................................................................... 19 2.3. Test Procedure ................................................................................................................ 20 2.4. Test Specification ............................................................................................................ 20 2.5. Test Result ...................................................................................................................... 20 3. Maximum peak conducted output power .................................................................................... 21 3.1. Test Setup ....................................................................................................................... 21 3.2. Test procedures ............................................................................................................... 21 3.3. Limits ............................................................................................................................... 21 3.4. Test Specification ............................................................................................................ 21 3.5. Test Result ...................................................................................................................... 22 4. Radiated Emission ...................................................................................................................... 25 4.1. Test Setup ....................................................................................................................... 25 4.2. Limits ............................................................................................................................... 26 4.3. Test Procedure ................................................................................................................ 27 4.4. Test Specification ............................................................................................................ 27 4.5. Test Result ...................................................................................................................... 28 5. RF antenna conducted test ......................................................................................................... 52 5.1. Test Setup ....................................................................................................................... 52 5.2. Limits ............................................................................................................................... 52 5.3. Test Procedure .......…

Text truncated - open the document above for the full version.

Report No：2020009R-RFUSP01V01-A Page: 1 of 74 FCC Test Report Product Name ：Android Based UI Trade Name ：PCI Model No. ：CSD-ELINK2 FCC ID. ：LY5-PCIABUI Applicant ： PCI Private Limited Address ： 35 Pioneer Road North, Singapore 628475 Singapore Date of Receipt：Feb. 03, 2020 Issued Date ：Mar. 17, 2020 Report No. ：2020009R-RFUSP01V01-A Report Version ：V1.0 The test results relate only to the samples tested. The test report shall not be reproduced except in full without the written approval of DEKRA Testing and Certification Co., Ltd. Report No：2020009R-RFUSP01V01-A Page: 2 of 74 Test Report Certification Issued Date: Mar. 17, 2020 Report No. : 2020009R-RFUSP01V01-A Product Name : Android Based UI Applicant : PCI Private Limited Address : 35 Pioneer Road North, Singapore 628475 Singapore Manufacturer : PCI Private Limited Address : 35 Pioneer Road North, Singapore 628475 Singapore Trade Name : PCI Model No. : CSD-ELINK2 FCC ID. : LY5-PCIABUI EUT Voltage : DC 5V Testing Voltage : DC 5V Applicable Standard : FCC CFR Title 47 Part 15 Subpart C Section 15.247: 2018 ANSI C63.10: 2013 Laboratory Name : Hsin Chu Laboratory Address : No.372-2, Sec. 4, Zhongxing Rd., Zhudong Township, Hsinchu County 310, Taiwan, R.O.C. TEL: +886-3-582-8001 / FAX: +886-3-582-8958 Test Result : Complied Documented By : ( Carol Tsai / Senior Engineering Adm. Specialist ) Tested By : ( Rueyyan Lin / Senior Engineer ) Approved By : ( Louis Hsu / Deputy Manager ) Report No：2020009R-RFUSP01V01-A Page: 3 of 74 Revision History Report No. Version Description Issued Date 2020009R-RFUSP01V01-A V1.0 Initial issue of report Mar. 17, 2020 Report No：2020009R-RFUSP01V01-A Page: 4 of 74 TABLE OF CONTENTS Description Page 1. General Information .................................................................................................................. 6 1.1. EUT Description ......................................................................................................... 6 1.2. Test Mode ................................................................................................................... 7 1.3. Tested System Details ................................................................................................ 8 1.4. Configuration of tested System .................................................................................. 8 1.5. EUT Exercise Software .............................................................................................. 8 1.6. Test Facility ................................................................................................................. 9 1.7. List of Test Equipment .............................................................................................. 11 1.8. Duty cycle ................................................................................................................. 13 1.9. Uncertainty ............................................................................................................... 14 2. Conducted Emission .............................................................................................................. 15 2.1. Test Setup................................................................................................................. 15 2.2. Limits ........................................................................................................................ 15 2.3. Test Procedure ......................................................................................................... 15 2.4. Test Specification ...................................................................................................... 15 2.5. Test Result ................................................................................................................ 15 3. Maximum peak conducted output power ................................................................................ 16 3.1. Test Setup................................................................................................................. 16 3.2. Test procedures ........................................................................................................ 16 3.3. Limits ........................................................................................................................ 16 3.4. Test Specification ...................................................................................................... 16 3.5. Test Result ................................................................................................................ 17 4. Radiated Emission ................................................................................................................. 18 4.1. Test Setup................................................................................................................. 18 4.2. Limits ........................................................................................................................ 19 4.3. Test Procedure ......................................................................................................... 20 4.4. Test Specification ...................................................................................................... 20 4.5. Test Result ................................................................................................................ 21 5. RF antenna conducted test .................................................................................................... 2 9 5.1. Test Setup................................................................................................................. 29 5.2. Limits ........................................................................................................................ 29 5.3. Test Procedure ......................................................................................................... 29 5.4. Test Specification .................................................................…

Text truncated - open the document above for the full version.

Report No：2020009R-RFUSP01V01 Page: 125 of 144 Attachment 1  Test Setup Photograph <Radiated Emission> Test Mode ： Mode 1: Transmit Mode Description： Front View of Radiated Emission Test Setup (Bilog) Description： Back View of Radiated Emission Test Setup (Bilog) Report No：2020009R-RFUSP01V01 Page: 126 of 144 Test Mode ： Mode 1: Transmit Mode Description： Front View of Radiated Emission Test Setup (Horn) Description： Back View of Radiated Emission Test Setup (Horn)