N5RUSWD500Data transmitter

U.S. WIRELESS DATA ® INC . Delivering The New Standard In Transaction Processing USWD500 CDPD Data Module User’s Installation Manual For CDPD Version 1.1 with UDP/TCP Protocol Version 2.0.6 August 27, 1998 FCC Information The Federal Communication Commission Radio Frequency Interference Statement includes the following paragraph: This equipment has been tested and found to comply with the limits for a Class B Digital Device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and radiates radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communication. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: • Reorient or relocate the receiving antenna. • Increase the separation between the equipment and receiver. • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. • Consult the dealer or an experienced radio / TV technician for help. The user should not modify or change this equipment without written approval from U.S. Wireless Data. Modification could void authority to use this equipment. While this device is in operation, a separation distance of at least 20 centimeters is maintained between radiating antennas and the body of the user or nearby persons in order to meet the FCC RF exposure guidelines. Copyright Copyright © 1998 U.S. Wireless Data, Inc., all rights reserved. No part of this publication may be reproduced, adapted, stored in a retrieval system, translated into any language, or transmitted in any form or by any means without the written permission of U.S. Wireless Data, Inc. Trademarks USWD500 is a trademark of U.S. Wireless Data, Inc. Limited Warranty In no event will U.S. Wireless Data, Inc. be liable for any damage, including loss of data or profits, cost of cover, or other incidental, consequential or indirect damages arising from the installation, maintenance, use, performance, failure or interruption of USWD’s products, for whatever cause and on any theory of liability. This limitation will apply even if U.S. Wireless Data has been advised of the possibility of such damage. Technical Support U.S. Wireless Data, Inc. Address:2200 Powell St., Emeryville, CA 94608-1809 Tel. No.: (510) 596-2025 Fax No.: (510) 596-2029 E-mail: [email protected] [email protected] [email protected] Web Site:http://www.uswdata.com About This Manual USWD500 User’s and Installation Manual was first published by U.S. Wireless Data, Inc., in 1997. This revision is for USWD500 for CDPD Version 1.1 with UDP/TCP Protocol, issued in July 1998. The purpose of this manual is for the setup of the product USWD500. It includes procedures that shall assist you to avoid unforeseen problems. CONTENTS Chapter 1 Introduction ...................................................................................................1 1-1 W HO S HOULD R EAD THIS M ANUAL ......................................................................1 1-2 P URPOSE OF THIS M ANUAL .................................................................................1 1-3 G ENERAL D ESCRIPTION & F EATURES ..................................................................1 1-4 USWD500 Product Package and Services ...........................................2 1-4-1 Product Package.................................................................................2 1-4-2 Services .............................................................................................2 1-5 H OW TO U SE THIS M ANUAL .................................................................................2 Chapter 2 Product Specifications ..................................................................................3 2-1 H ARDWARE S PECIFICATIONS ...............................................................................3 2-2 I/O P INS A SSIGNMENT (FFC C ONNECTOR )..........................................................5 2-3 M ECHANICAL S PECIFICATIONS .............................................................................6 Chapter 3 Installation, Setup & Test ..............................................................................8 3-1 I NSTALLATION & S ETUP ......................................................................................8 3-1-1 Basic Testing: Verify the USWD500 Working Status ..........................8 3-1-2 Connect to the CDPD Network ..........................................................8 3-1-2-1 Installation Procedures ............................................................9 3-1-2-2 General Parameters Setup....................................................13 3-1-2-3 Advance Parameters Setup ..................................................15 3-1-3 Useful Commands ...........................................................................17 3-2 U SING USWD500 WITH T ERMINAL P ROGRAM ....................................................19 3-2-1 UDP Concept ...................................................................................19 3-2-2 Data Transmitting and Receiving under UDP Protocol ....................19 3-2-3 When will USWD 500 send out the queued data .............................19 3-3 U SING USWD500 WITH WIN95 .......................................................................20 3-4 B ROADCAST AND M ULTICAST ............................................................................21 3-4-1 Broadcast.........................................................................................21 3-4-2 Multicast............................…

Text truncated - open the document above for the full version.

USWD500 CDPD Modem User’s Manual For CDPD Version 1.1 with UDP/TCP Protocol Version 3.01 February 5, 1999 FCC Information The Federal Communication Commission Radio Frequency Interference Statement includes the following paragraph: This equipment has been tested and found to comply with the limits for a Class B Digital Device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and radiates radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communication. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: • Reorient or relocate the receiving antenna. • Increase the separation between the equipment and receiver. • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. • Consult the dealer or an experienced radio / TV technician for help. The user should not modify or change this equipment without written approval from U.S. Wireless Data. Modification could void authority to use this equipment. WARNING LABEL This label will be placed on the final product, clearly visible to all persons exposed to the transmitter. The specific location on the final product will be consistent with each same final product, but will vary in location across various final products, and in any case will always be clearly visible to all persons exposed to the transmitter. The physical size of the label and font size of the lettering will be dependent on the size of the final product, but in any case will always be clearly visible to all persons exposed to the transmitter. WARNING LABEL EXAMPLE While this device is in operation, a separation distance of at least 20 centimeters must be maintained between radiating antennas and the body of the user or nearby persons in order to meet the F CC RF exposure guidelines. Copyright Copyright © 1999 U.S. Wireless Data, Inc., all rights reserved. No part of this publication may be reproduced, adapted, stored in a retrieval system, translated into any language, or transmitted in any form or by any means without the written permission of U.S. Wireless Data, Inc. Trademarks USWD500 is a trademark of U.S. Wireless Data, Inc. Limited Warranty In no event will U.S. Wireless Data, Inc. be liable for any damage, including loss of data or profits, cost of cover, or other incidental, consequential or indirect damages arising from the installation, maintenance, use, performance, failure, or interruption of USWD’s products, for whatever cause and on any theory of liability. This limitation will apply even if U.S. Wireless Data has been advised of the possibility of such damage. Technical Support U.S. Wireless Data, Inc. Address: 2200 Powell Street, Emeryville, CA 94608-1809 Telephone: (510) 596-2025 Fax: (510) 596-2029 E-mail: [email protected] [email protected] [email protected] Web Site:http://www.uswdata.com About This Manual The USWD500 User’s Manual was first published by U.S. Wireless Data, Inc., in 1997. This revision is for the USWD500 for CDPD Version 1.1 with UDP/TCP Protocol, issued in July 1998. This manual provides information for setting up, maintaining, and troubleshooting the USWD500 CDPD Modem. USWD500 User’s Manual 0 CONTENTS Chapter 1Introduction................................................................................................ 3 Who Should Read this Manual .......................................................................................... 3 Purpose of this Manual ...................................................................................................... 3 General Description and Features .................................................................................... 3 USWD500 Product Package and Services ........................................................................ 4 Product Package.................................................................................................................................4 Services ..............................................................................................................................................4 How to Use this Manual ..................................................................................................... 4 Chapter 2Product Specifications.............................................................................. 5 Hardware Specifications .................................................................................................... 5 General Specifications ....................................................................................................... 5 Receiver Specifications ..................................................................................................... 6 Transmitter Specifications................................................................................................. 7 I/O Pin Assignments (FFC Connector).............................................................................. 8 Mechanical Specifications ................................................................................................. 9 Mechanical Size.................................................................................................................. 9 MMCX RF Connector........................................................................................................ 10 FFC 30-pin connector (ZIF) ...............................................................................................11 Chapter 3Installation and Setup ..................................…

Text truncated - open the document above for the full version.

USWD500 CDPD Modem User’s Manual For CDPD Version 1.1 with UDP/TCP Protocol Version 3.01 February 8, 1999 FCC Information The Federal Communication Commission Radio Frequency Interference Statement includes the following paragraph: This equipment has been tested and found to comply with the limits for a Class B Digital Device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and radiates radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communication. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: • Reorient or relocate the receiving antenna. • Increase the separation between the equipment and receiver. • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. • Consult the dealer or an experienced radio / TV technician for help. The user should not modify or change this equipment without written approval from U.S. Wireless Data. Modification could void authority to use this equipment. WARNING LABEL This label will be placed on the final product, clearly visible to all persons exposed to the transmitter. The specific location on the final product will be consistent with each same final product, but will vary in location across various final products, and in any case will always be clearly visible to all persons exposed to the transmitter. The physical size of the label and font size of the lettering will be dependent on the size of the final product, but in any case will always be clearly visible to all persons exposed to the transmitter. Note: If your product is in compliance with SAR limits as defined by the FCC, the following warning label is not required. WARNING LABEL EXAMPLE WARNING While this device is in operation, a separation distance of at least 20 centimeters must be maintained between radiating antennas and the body of the user or nearby persons in order to meet the FCC RF exposure guidelines. Copyright Copyright © 1999 U.S. Wireless Data, Inc., all rights reserved. No part of this publication may be reproduced, adapted, stored in a retrieval system, translated into any language, or transmitted in any form or by any means without the written permission of U.S. Wireless Data, Inc. Trademarks USWD500 is a trademark of U.S. Wireless Data, Inc. Limited Warranty In no event will U.S. Wireless Data, Inc. be liable for any damage, including loss of data or profits, cost of cover, or other incidental, consequential or indirect damages arising from the installation, maintenance, use, performance, failure, or interruption of USWD’s products, for whatever cause and on any theory of liability. This limitation will apply even if U.S. Wireless Data has been advised of the possibility of such damage. Technical Support U.S. Wireless Data, Inc. Address: 2200 Powell Street, Emeryville, CA 94608-1809 Telephone: (510) 596-2025 Fax: (510) 596-2029 E-mail: [email protected] [email protected] [email protected] Web Site:http://www.uswdata.com About This Manual The USWD500 User’s Manual was first published by U.S. Wireless Data, Inc., in 1997. This revision is for the USWD500 for CDPD Version 1.1 with UDP/TCP Protocol, issued in July 1998. This manual provides information for setting up, maintaining, and troubleshooting the USWD500 CDPD Modem. USWD500 User’s Manual 0 CONTENTS Chapter 1Introduction ................................................................................................3 Who Should Read this Manual .......................................................................................... 3 Purpose of this Manual ...................................................................................................... 3 General Description and Features .................................................................................... 3 USWD500 Product Package and Services........................................................................ 4 Product Package.......................................................................................................................... 4 Services ....................................................................................................................................... 4 How to Use this Manual ..................................................................................................... 4 Chapter 2Product Specifications ..............................................................................5 Hardware Specifications.................................................................................................... 5 General Specifications....................................................................................................... 5 Receiver Specifications ..................................................................................................... 6 Transmitter Specifications................................................................................................. 7 I/O Pin Assignments (FFC Connector).............................................................................. 8 Mechanical Specifications ................................................................................................. 9 Mechanical Size.................................................................................................................. 9 MMCX RF Connector........................................................................................................ 10 FFC 30-pin connector (ZIF)..................................................…

Text truncated - open the document above for the full version.

USWD500 CDPD Modem User’s Manual For CDPD Version 1.1 with UDP/TCP Protocol Version 3.0.2 February 16, 1999 FCC Information The Federal Communication Commission Radio Frequency Interference Statement includes the following paragraph: This equipment has been tested and found to comply with the limits for a Class B Digital Device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and radiates radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communication. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: • Reorient or relocate the receiving antenna. • Increase the separation between the equipment and receiver. • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. • Consult the dealer or an experienced radio / TV technician for help. The user should not modify or change this equipment without written approval from U.S. Wireless Data. Modification could void authority to use this equipment. WARNING LABEL The warning label, shown in Exhibit A, must be placed on the final product, clearly visible to all persons exposed to the transmitter. The specific location on the final product will be consistent with each same final product, but will vary in location across various final products, and in any case will always be clearly visible to all persons exposed to the transmitter. The physical size of the label and font size of the lettering will be dependent on the size of the final product, but in any case will always be clearly visible to all persons exposed to the transmitter. Note: The warning label shown in Exhibit A is not required when SAR compliance of the final product is approved through separate FCC equipment authorization approvals. Exhibit A WARNING While this device is in operation, a separation distance of at least 20 centimeters must be maintained between radiating antennas and the body of the user or nearby persons in order to meet the FCC RF exposure guidelines. Copyright Copyright © 1999 U.S. Wireless Data, Inc., all rights reserved. No part of this publication may be reproduced, adapted, stored in a retrieval system, translated into any language, or transmitted in any form or by any means without the written permission of U.S. Wireless Data, Inc. Trademarks USWD500 is a trademark of U.S. Wireless Data, Inc. Limited Warranty In no event will U.S. Wireless Data, Inc. be liable for any damage, including loss of data or profits, cost of cover, or other incidental, consequential or indirect damages arising from the installation, maintenance, use, performance, failure, or interruption of USWD’s products, for whatever cause and on any theory of liability. This limitation will apply even if U.S. Wireless Data has been advised of the possibility of such damage. Technical Support U.S. Wireless Data, Inc. Address: 2200 Powell Street, Emeryville, CA 94608-1809 Telephone: (510) 596-2025 Fax: (510) 596-2029 E-mail: [email protected] [email protected] [email protected] Web Site:http://www.uswdata.com About This Manual The USWD500 User’s Manual was first published by U.S. Wireless Data, Inc., in 1997. This revision is for the USWD500 for CDPD Version 1.1 with UDP/TCP Protocol, issued in July 1998. This manual provides information for setting up, maintaining, and troubleshooting the USWD500 CDPD Modem. USWD500 User’s Manual 1 CONTENTS Chapter 1Introduction................................................................................................ 4 Who Should Read this Manual .......................................................................................... 4 Purpose of this Manual ...................................................................................................... 4 General Description and Features .................................................................................... 4 USWD500 Product Package and Services ........................................................................ 5 Product Package.................................................................................................................................5 Services ..............................................................................................................................................5 How to Use this Manual ..................................................................................................... 5 Chapter 2Product Specifications.............................................................................. 6 Hardware Specifications .................................................................................................... 6 General Specifications ....................................................................................................... 6 Receiver Specifications ..................................................................................................... 7 Transmitter Specifications................................................................................................. 8 I/O Pin Assignments (FFC Connector) .............................................................................. 9 Mechanical Specifications ............................................................................................... 10 Mechanical Size................................................................................................................10 MMCX RF Connector.........................................................................................................11 …

Text truncated - open the document above for the full version.

USWD500 CDPD Modem User’s Manual For CDPD Version 1.1 with UDP/TCP Protocol Version 3.0.3 February 18, 1999 FCC Information The Federal Communication Commission Radio Frequency Interference Statement includes the following paragraph: This equipment has been tested and found to comply with the limits for a Class B Digital Device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and radiates radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communication. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: • Reorient or relocate the receiving antenna. • Increase the separation between the equipment and receiver. • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. • Consult the dealer or an experienced radio / TV technician for help. The user should not modify or change this equipment without written approval from U.S. Wireless Data. Modification could void authority to use this equipment. WARNING LABEL The warning label, shown in Exhibit A, must be placed on the final product, clearly visible to all persons exposed to the transmitter. The specific location on the final product will be consistent with each same final product, but will vary in location across various final products, and in any case will always be clearly visible to all persons exposed to the transmitter. The physical size of the label and font size of the lettering will be dependent on the size of the final product, but in any case will always be clearly visible to all persons exposed to the transmitter. Note: The warning label shown in Exhibit A is not required when SAR compliance of the final product is approved through separate FCC equipment authorization approvals. Exhibit A WARNING While this device is in operation, a separation distance of at least 20 centimeters must be maintained between radiating antennas and the body of all persons exposed to the transmitter in order to meet the FCC RF exposure guidelines. Copyright Copyright © 1999 U.S. Wireless Data, Inc., all rights reserved. No part of this publication may be reproduced, adapted, stored in a retrieval system, translated into any language, or transmitted in any form or by any means without the written permission of U.S. Wireless Data, Inc. Trademarks USWD500 is a trademark of U.S. Wireless Data, Inc. Limited Warranty In no event will U.S. Wireless Data, Inc. be liable for any damage, including loss of data or profits, cost of cover, or other incidental, consequential or indirect damages arising from the installation, maintenance, use, performance, failure, or interruption of USWD’s products, for whatever cause and on any theory of liability. This limitation will apply even if U.S. Wireless Data has been advised of the possibility of such damage. Technical Support U.S. Wireless Data, Inc. Address: 2200 Powell Street, Emeryville, CA 94608-1809 Telephone: (510) 596-2025 Fax: (510) 596-2029 E-mail: [email protected] [email protected] [email protected] Web Site:http://www.uswdata.com About This Manual The USWD500 User’s Manual was first published by U.S. Wireless Data, Inc., in 1997. This revision is for the USWD500 for CDPD Version 1.1 with UDP/TCP Protocol, issued in July 1998. This manual provides information for setting up, maintaining, and troubleshooting the USWD500 CDPD Modem. USWD500 User’s Manual 1 CONTENTS Chapter 1Introduction................................................................................................ 4 Who Should Read this Manual .......................................................................................... 4 Purpose of this Manual ...................................................................................................... 4 General Description and Features .................................................................................... 4 USWD500 Product Package and Services ........................................................................ 5 Product Package.................................................................................................................................5 Services ..............................................................................................................................................5 How to Use this Manual ..................................................................................................... 5 Chapter 2Product Specifications.............................................................................. 6 Hardware Specifications .................................................................................................... 6 General Specifications ....................................................................................................... 6 Receiver Specifications ..................................................................................................... 7 Transmitter Specifications................................................................................................. 8 I/O Pin Assignments (FFC Connector) .............................................................................. 9 Mechanical Specifications ............................................................................................... 10 Mechanical Size................................................................................................................10 MMCX RF Connector................................................................................................…

Text truncated - open the document above for the full version.