N7U-ERFOLG1

How to use LOVEGETY2 1. Please power on ,select liking mode by mode button. Selected the mode can confirm by red indicator switch on and off . 2. when the men’s equipment of power on condition come near , if mode is same , “GET LED” is switch on and off . 3. If not “FIND LED” is switch on and off , men’s equipment will inform to be near . At that time , please change over mode switch . “GET LED” is switch on and off at one of these modes . FCC NOTICE CHANGE OR MODIFICATIONS NOT EXPESSLY APPROVED BY THE MANUFACTURER FOR COMPLIANCE COULD THE USER’S AUTHORITY TO OPERATE THE EQUIPMENT. NOTE : This equipment has been tested and found to comply with the limits for a Class B designed device, pursuant to Part 15 of the FCC Rules . These limits are designed to provide reasonable protection against harmful interference in a residential installation . This equipment generates, use and can radiate radio frequency energy . and, if not installed and used in accordance with instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does not harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: GET FIND POWER SWITCH Continue to push all of the LED switch on and off ,then be able to conform power on . MODE SWITCH Please select to liking the mode ALARM SWITCH Beeper ring when operate GET or FIND. Please power off when not used . GET LED when mode is same, GET LED switch on and off. FIND LED FIND LED switched on and off when the women’s setting different mode has came near side . MODE INDICATOR Selected of the mode switch on and off. STEARVING BOOZE FLICK CHAT FUN HELP ! Use 2 pcs UM-3 or “AA” 1.5V alkaline battery ! Please replace all batteries at the same time , do not mix old and new batteries . ! Don’t mix with a different type of battery . ! Please do not try to recharge the battery or put it into the fire . Each of part name and function This equipment is women’s . It respond to men’s. Reorient or relocate the receiving antenna . Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help.

FCC ID : N7U-ERFOLG1 two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference that may cause undesired operations. This device complies with Part 15 of the FCC rules. Operation is subject to the following

1 SUMMARY SPECIFICATIONS Description The ERFOLG1 transmits radio wave and receive periodically. The transmitting radio wave has different patterns by selected mode. In this receiving mode when a specific pattern is received. If the received pattern is the same as the selected mode, “GET LED” is switched on and off. If not “FIND LED” is switched on and off. After “LED” is switched on and off either BUZZER or VIBRATION MOTOR will be activated. BUZZER or VIBRATION MOTOR can be selected by slide switch. The ERFOLG2 always is in the mode of receiving. In this receiving mode when a specific pattern is received, than it transmits radio wave base on a selected mode. If the received pattern is the same as the selected mode, “GET LED” is switched on and off. If not “FIND LED” is switched on and off. After “LED” is switched on and off either BUZZER or VIBRATION MOTOR will be activated. BUZZER or VIBRATION MOTOR can be selected by slide switch. Basic Function LED BUZZER VIBRATOR
How to switch the working mode. Each mode is switched by a slide switch. TX/RX mode TX/RX mode will be changed 6 channels.
How to switch the TX/RX mode It is switched in tune 6 channels when press the push switch button. Timing Chart TX RX off on off on SET A RECEIVE on off ABB A A C D F G G H HG G H I E 2 timems nameMODE1MODE2MODE3MODE4MODE5MODE6 memo A 302520605550TX on B 302520605550TX off C150125100300250200RX off D762787812612662712RX on E912912912912912912cycle FMIN 256 MIN 270 MIN 270 G15105454035TX on H15105454035TX off IMIN 276 MIN 326 MIN 376 J755025225200175RX off K837862887687712737RX on RECEIVE J K F AB B A A E J IC F Start TX A and G (details) 0.1ms (10kHz:duty 50%) off on 3

Circuit explanation Control section U1CPUcontrol all of the control circuit . The S2 can control to supply . The mode is selected by S1 . U5 and Q4 are controlled as follow as The selected mode and receiving result . S3 select which B1 or BZ1 . the each of these drive Q4 and Q5 . LED are driving by U2 . U6 detect low voltage . Transmitter section The transmitter is controlled at Q1,Q3 and Q9 .The transmitter frequency is 315MHz . U3 is oscillator at about 10kHz . Receiving section The receiving frequency is 300MHz. The Receiving is detected by the super regenerative circuit . The circuit is composed of Q6 and Q8 . The regeneration signal is making the waveform by U4 and Q3 . The waveform input U1 . Q2 control timing .