NKR-P111abgn 2x2 USB WiFi module

11abgn 2x2 USB WiFi module Panasonic DNUR-P1 User Manual Copyright Statement No part of this publication may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, whether electronic, mechanical, photocopying, recording or otherwise without the prior writing of the publisher. Pentium is trademark of Intel. All copyright reserved. 1 FCC Statement: Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures: ● Reorient or relocate the receiving antenna. ● Increase the separation between the equipment and receiver. ● Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. ● Consult the dealer or an experienced radio/TV technician for help. FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate this equipment. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This device and its antenna(s) must not be co-located or operation in conjunction with any other antenna or transmitter. For product available in the USA/Canada market, only channel 1~11 can be operated. Selection of other channels is not possible. This device is restricted to indoor use when operated in the 5.15 to 5.25 GHz frequency range. ※ FCC requires this product to be used indoors for the frequency range 5.15 to 5.25 GHz to reduce the potential for harmful interference to co-channel Mobile Satellite systems. ※ This device will not permit operations on channels 116-128 for 11na and 120-128 for 11a which overlap the 5600 -5650MHz band. 2 IMPORTANT NOTE: FCC Radiation Exposure Statement: This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body. IMPORTANT NOTE: This module is intended for OEM integrator. The OEM integrator is still responsible for the FCC compliance requirement of the end product, which integrates this module. 20cm minimum distance has to be able to be maintained between the antenna and the users for the host this module is integrated into. Under such configuration, the FCC radiation exposure limits set forth for an population/uncontrolled environment can be satisfied. Any changes or modifications not expressly approved by the manufacturer could void the user's authority to operate this equipment. USERS MANUAL OF THE END PRODUCT: In the user’s manual of the end product, the end user has to be informed to keep at least 20cm separation with the antenna while this end product is installed and operated. The end user has to be informed that the FCC radio-frequency exposure guidelines for an uncontrolled environment can be satisfied. The end user has to also be informed that any changes or modifications not expressly approved by the manufacturer could void the user's authority to operate this equipment. If the size of the end product is smaller than 8x10cm, then additional FCC part 15.19 statement is required to be available in the users manual: This device complies with Part 15 of FCC rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference and (2) this device must accept any interference received, including interference that may cause undesired operation. LABEL OF THE END PRODUCT: The final end product must be labeled in a visible area with the following "Contains FCC ID: NKR-P1 ". If the size of the end product is larger than 8x10cm, then the following FCC part 15.19 statement has to also be available on the label: This device complies with Part 15 of FCC rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference and (2) this device must accept any interference received, including interference that may cause undesired operation. 3 This radio module (FCC: NKR-P1/ Model: DNUR-P1) has been approved to operate with the antenna types listed below with its antenna type and maximum permissible gain: Type Gain Remark Printed 0.67dBi 2.4GHz band Printed 2.15dBi 5GHz band The two antenna connectors of this module are only for test purpose and should not be connected with any external antenna. Any other antenna is strictly prohibited for use with this module without futher authorization by FCC. 4 Industry Canada statement: This Class B digital apparatus complies with Canadian ICES-003. Cet appareil numérique de la classe B conforme á la norme NMB-003 du Canada. This device complies with RSS-210 of the Industry Canada Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Ce dispositif est conforme à la norme CNR-210 d'Industrie Canada applicable aux appareils radio exempts de licence. Son fonctionnement est sujet aux deux conditions suivantes: (1) …

Text truncated - open the document above for the full version.

Date: December 4, 2012 Subject: Ad Hoc Mode Function Declaration FCC ID: NKR-P1 IC: 4441A-P1 To Whom it may concern, We, Wistron NeWeb Corporation, declare that the device (FCC ID: NKR-P1 /IC: 4441A-P1) 1. is able to be operated on client mode. 2. does not have Ad-hoc function on channels within the frequency bands a. Band 2: 5250 – 5350MHz b. Band 3: 5470 – 5725MHz 3. Ad-hoc will be supported in 802.11bgn(2412~2462MHz) mode and 802.11a (Band1: 5150~5250MHz; Band4:5725~5850MHz) 4. is acting as client without DFS detection capability. 5. cannot operate as a client device on frequencies within the band 5600 – 5650MHz in US/Canada. 6. is not able to operate in non-US/IC frequencies, country code selection will be disable for this device. 7. In non associated mode, that software and associated drivers will not initiate any transmission on DFS frequencies. This includes transmissions for beacon ad-hoc peer-to-peer modes. (KDB848637) Regards, Applicant : Wistron NeWeb Corporation Address : 20 Park Avenue II, Hsinchu Science Park, Hsinchu 308,Taiwan,R.O.C. Signature : Name and Job Title. : Alan Wang / Engineer E-mail [email protected] Tel. +886 3 6667799 #6907

A G E N C Y A U T H O R I Z A T I O N L E T T E R Date: 2012-12-04 I, Troy Chien, am associate technical director for Wistron NeWeb Corp. hereby authorize the following to act on our behalf, as our agent, in all matters relating to all processes required according to FCC approval for Wistron NeWeb Corp. products (Grantee Code: NKR) Alan Wang If you have any questions regarding the authorization, please don’t hesitate to contact us. Thank you! Sincerely yours, __________________________________ Troy Chien / Associate Technical Director Tel: +886-3-6667799 Fax: +886-3-6667323 E-mail:[email protected]

Confidentiality Request Letter Date: 2012/12/4 Federal Communications Commission Authorization and Evaluation Division FCC ID：NKR-P1 Permanent Confidentiality Request Pursuant to Sections 0.457 and 0.459 of the Commission’s Rules, the Applicant Hereby requests confidential treatment of information accompanying this Application As outlined below: 1. Block Diagram 2. Circuit Diagram 3. Operational Description The above materials contain trade secrets and proprietary information not customarily released to the public. The public disclosure of these matters might be harmful to the Applicant and provide unjustified benefits to its competitors. The Applicant understands that pursuant to Rule 0.457, disclosure of this Application and all accompanying documentation will not be made before the date of the Grant for this application Sincerely, Applicant’s company name : Wistron NeWeb Corporation Applicant’s company address : 20 Park Avenue II, Hsinchu Science Park, Hsinchu 308,Taiwan,R.O.C. Signature : Job Title and Dept. : Alan Wang / Engineer E-mail : [email protected] Tel. : +886 3 6667799 #6907

International Certification Corp. (全球檢測股份有限公司) Tel：886-3-271-8666 Fax : 886-3-318-0155 No.3-1, Lane 6, Wen 33rd Rd., Kwei Shan Hsiang, Tao Yuan Hsein 333, Taiwan (R.O.C.) Gary Chang , Manager Report & Certification department Tel:+886-3-271-8628 Email:[email protected] Subject: Modular approval request FCC ID: NKR-P1 Date: December 18, 2012 Dear reviewer: The modular would like to have authorization as a modular approval. The requirements of section 15.212 have been met and shown on the following statements 1) The radio elements of the modular transmitter must have their own shielding The modular has shielding. Please refer to external photo. 2) The modular transmitter must have buffered modulation/da ta inputs The buffer is integrated with IC RT5572 3) The modular transmitter must have its own power supply regulation The part No. of regulator is AUR9717 4) The modular transmitter must comply with the antenna and transmission system requirements of §§15.203, 15.204(b) and 15.204 (c). The modular complies with above requirement. 5) The modular transmitter must be tested in a stand-alone configuration The modular is tested in a stand-alone configuration via an extender. Please refer to test setup photo. 6) The modular transmitter must be equipped with either a permanently affixed label or must be cap able of electronically displaying its FCC identification number. The modular complies with the requirement. Please refer to label location and label sample exhibit. 7) The modular transmitter must comply with any specific rules or operating requirements The modular complies with the requirement. Detail information please refer to user manual 8) The modular transmitter must comply with any applicable RF exposure requirements in its final configuration. The modular complies with the requirement. Please refer to RF exposure exhibit Please contact me if you have any questions about this letter. Best regards

Date: 2012/12/4 Federal Communications Commission 7435 Oakland Mills Rd Columbia MD 21046-1609 Subject: Product Certification Representative Authorization Letter FCC ID: NKR-P1 Product name: 11abgn 2x2 USB WiFi module To whom it may concern: We the undersigned, hereby authorize following person to act as our agent in the preparation of an application for equipment authorization of model DNUR-P1 to the FCC Rules and Regulations. International Certification Corp. Address : No.3-1, Lane 6, Wen 33rd Rd., Kwei Shan Hsiang, Tao Yuan Hsein 333, Taiwan (R.O.C.) Name : Gary Chang Job Title : Manager e-mail : [email protected] Webs We further certifies that neither the applicant nor any party to this application, as defined in 47 CFR Ch. 1.2002(b), is subject to a denial to Federal benefits, that include FCC benefits, pursuant to section 5301 of the Anti-Drug Abuse Act of 1998, 21 U.S.C. 835(a). This appointment also includes the authority to complete FCC Form 731 on our behalf and sign the application as an authorized agent. Note: The registered grantee contact is not avliable, 現在簽署人名 is signing for grantee contact. He can be reached at email :xxxxxxxxxxx(現在簽署人email). Applicant : Wistron NeWeb Corporation Address : 20 Park Avenue II, Hsinchu Science Park, Hsinchu 308,Taiwan,R.O.C. Signature : _________________________________ Name and Job Title. : Alan Wang / Engineer E-mail : [email protected] Tel. : +886 3 6667799 #6907

IC Test Report Report No. : CR2N2717 SPORTON International Inc. TEL : 886-3-327-3456 FAX : 886-3-327-0973 PAGE NUMBER : B1 OF B3 ISSUED DATE : Dec. 13, 2012 APPENDIX B. Photographs of EUT

Panasonic / DNUR-P1 Label Location

IC Test Report Report No. : CR2N2717 SPORTON International Inc. TEL : 886-3-327-3456 FAX : 886-3-327-0973 PAGE NUMBER : B2 OF B3 ISSUED DATE : Dec. 13, 2012 IC Test Report Report No. : CR2N2717 SPORTON International Inc. TEL : 886-3-327-3456 FAX : 886-3-327-0973 PAGE NUMBER : B3 OF B3 ISSUED DATE : Dec. 13, 2012 IC Test Report Report No. : CR2N2717 SPORTON International Inc. TEL : 886-3-327-3456 FAX : 886-3-327-0973 PAGE NUMBER : B4 OF B3 ISSUED DATE : Dec. 13, 2012

FCC Test Report Report No. : FR2N2717 SPORTON INTERNATIONAL INC. Page No. : 1 of 5 TEL : 886-3-327-3456 Report Version : Rev. 01 FAX : 886-3-327-0973 1 Human Exposure Assessment 1.1 Maximum Permissible Exposure 1.1.1 Limit of Maximum Permissible Exposure Limits for Occupational / Controlled Exposure Frequency Range (MHz) Electric Field Strength (E) (V/m) Magnetic Field Strength (H) (A/m) Power Density (S) (mW/ cm²) Averaging Time |E|²,|H|² or S (minutes) 0.3-3.0 614 1.63 (100)* 6 3.0-30 1842 / f 4.89 / f (900 / f)* 6 30-300 61.4 0.163 1.0 6 300-1500 - - F/300 6 1500-100,000 - - 5 6 Limits for General Population / Uncontrolled Exposure Frequency Range (MHz) Electric Field Strength (E) (V/m) Magnetic Field Strength (H) (A/m) Power Density (S) (mW/ cm²) Averaging Time |E|²,|H|² or S (minutes) 0.3-1.34 614 1.63 (100)* 30 1.34-30 824/f 2.19/f (180/f)* 30 30-300 27.5 0.073 0.2 30 300-1500 - - F/1500 30 1500-100,000 - - 1.0 30 Note 1: f = frequency in MHz ; *Plane-wave equivalent power density Note 2: For the applicable limit, see FCC 1.1310 FCC Test Report Report No. : FR2N2717 SPORTON INTERNATIONAL INC. Page No. : 2 of 5 TEL : 886-3-327-3456 Report Version : Rev. 01 FAX : 886-3-327-0973 RF Field Strength Limits for Controlled Use Devices (Controlled Environment) Frequency Range (MHz) Electric Field (V/m rms) Magnetic Field (A/m rms) Power Density (W/m2) Averaging Time (minutes) 0.003-1 600 4.9 - 6 1-10 600/ƒ 4.9/ƒ - 6 10-30 60 4.9/ƒ - 6 30-300 60 0.163 10* 6 300-1500 3.54 ƒ 0.5 0.0094 ƒ 0.5 ƒ/30 6 1500-15000 137 0.364 50 6 15000-150000 137 0.364 50 616000/ƒ 1.2 150000-300000 0.354 ƒ 0.5 9.4 x 10-4 ƒ 0.5 3.33 x 10-4 ƒ 616000/ƒ 1.2 RF Field Strength Limits for Devices Used by the General Public (Uncontrolled Environment) Frequency Range (MHz) Electric Field (V/m rms) Magnetic Field (A/m rms) Power Density (W/m2) Averaging Time (minutes) 0.003-1 280 2.19 - 6 1-10 280/ƒ 2.19/ƒ - 6 10-30 28 2.19/ƒ - 6 30-300 28 0.073 2* 6 300-1500 1.585 ƒ 0.5 0.0042 ƒ 0.5 ƒ/150 6 1500-15000 61.4 0.163 10 6 15000-150000 61.4 0.163 10 616000/ƒ 1.2 150000-300000 0.158 ƒ 0.5 4.21 x 10 -4 ƒ 0.5 6.67 x 10 -5 ƒ 616000/ƒ 1.2 Note 1: ƒ is frequency in MHz. Note 2: For the applicable limit, see IC RSS-102 1.1.2 MPE Calculation Method E (V/m) = d GP30 Power Density: Pd (W/m 2 ) = 377 E 2 E = Electric field (V/m) P = RF output power (W) G = EUT Antenna numeric gain (numeric) d = Separation distance between radiator and human body (m) The formula can be changed to Pd = 2 d377 GP30   FCC Test Report Report No. : FR2N2717 SPORTON INTERNATIONAL INC. Page No. : 3 of 5 TEL : 886-3-327-3456 Report Version : Rev. 01 FAX : 886-3-327-0973 1.1.3 Result of Maximum Permissible Exposure-(2.4G) Transmitter Chains & Receiver Chains Information IEEE Std. 802.11 Protocol Number of Transmit Chains (N TX ) Number of Receive Chains (N RX ) Correlation Signals with Multiple N TX RF Output Power (dBm) Co-location 11B-20M 1 1 N/A 23.34 N/A 11G-20M 1 1 N/A 20.14 N/A n (HT-20) 2 2 Uncorrelated 22.77 N/A n (HT-40) 2 2 Uncorrelated 18.25 N/A Note 1: Co-location, Co-location is generally defined as simultaneously transmitting (co-transmitting) antennas within 20 cm of each other. (i.e., EUT has simultaneously co-transmitting that operating 2.4GHz and 5GHz.) Note 2: RF output power specifies that Maximum Conducted (Average) Output Power. Worst Maximum RF Output Power Result Exposure Environment General Population / Uncontrolled Exposure Separation Distance (cm) 20 Condition RF Output Power (dBm) Modulation Mode N TX Chain- Port 1 Chain- Port 2 - - Sum Chain DG (dBi) EIRP Power PD (S) (mW/cm²) 11B-20M 1 23.28 - - 23.34 0.67 24.01 0.05012 11G-20M 1 19.64 - - 20.14 0.67 20.81 0.02398 11N-HT-20 2 18.65 18.80 - - 22.77 0.21 22.98 0.03950 11N-HT-40 2 13.43 13.40 - - 18.25 0.21 18.47 0.01397 Maximum Permissible Exposure Limit (mW/cm²) 1 Note 1: N TX = Number of Transmit Chains FCC Test Report Report No. : FR2N2717 SPORTON INTERNATIONAL INC. Page No. : 4 of 5 TEL : 886-3-327-3456 Report Version : Rev. 01 FAX : 886-3-327-0973 1.1.4 Result of Maximum Permissible Exposure-(5.8G) Transmitter Chains & Receiver Chains Information IEEE Std. 802.11 Protocol Number of Transmit Chains (N TX ) Number of Receive Chains (N RX ) Correlation Signals with Multiple N TX RF Output Power (dBm) Co-location 11A5.8G-20M 1 1 Correlated 20.87 N/A 11N5.8G- HT20 2 2 Uncorrelated 21.22 N/A 11N5.8G- HT40 2 2 Uncorrelated 23.00 N/A Note 1: Co-location, Co-location is generally defined as simultaneously transmitting (co-transmitting) antennas within 20 cm of each other. (i.e., EUT has simultaneously co-transmitting that operating 2.4GHz and 5GHz.) Note 2: RF output power specifies that Maximum Conducted (Average) Output Power. Worst Maximum RF Output Power Result Exposure Environment General Population / Uncontrolled Exposure Separation Distance (cm) 20 Condition RF Output Power (dBm) Modulation Mode N TX Chain- Port 1 Chain- Port 2 - - Sum Chain DG (dBi) EIRP Power PD (S) (mW/cm²) 11A5.8G-20M 1 20.35- - - 20.87 2.15 23.02 0.03983 11N5.8G- HT20 2 17.29 17.17 - - 21.22 1.85* 23.06 0.04028 11N5.8G- HT40 2 18.05 18.19 - - 23.00 1.85* 24.85 0.06074 Maximum Permissible Exposure Limit (mW/cm²) 1 Note 1: N TX = Number of Transmit Chains Note 2:* Direction gain = 10 log[(10 1.52/10 + 10 2.15/10) /2]=1.85dBi FCC Test Report Report No. : FR2N2717 SPORTON INTERNATIONAL INC. Page No. : 5 of 5 TEL : 886-3-327-3456 Report Version : Rev. 01 FAX : 886-3-327-0973 1.1.5 Result of Maximum Permissible Exposure-(5.2G~5.6G) RF General Information Modulation Mode Ch. Freq. (MHz) Channel Number Transmit Chains (N TX ) RF Output Power (dBm) Co-location 11A5.2G-20M 5180-5240 36-48 [4] 1 14.79 N/A 11A5.3G-20M 5260-5320 52-64 [4] 1 20.37 11A5.6G-20M 5500-5700 100-140 [8] 1 20.87 11N5.2G-HT-20 5180-5240 36-48 [4] 2 14.53 N/A 11N5.3G-HT-20 5260-5320 52-64 [4] 2 21.59 11N5.6G-HT-20 5500-5700 100-140 [8] 2 21.26 11N5.2G-HT-40 5190-5230 38-46 [2] 2 16.60 N/A 11N5.3G-HT-40 5270-5310 54-62 [2] 2 22.65 11N5.6G-HT-40 5510-5…

Text truncated - open the document above for the full version.

FCC Test Report Report No. : FR2N2717AC SPORTON INTERNATIONAL INC. Page No. : 1 of 64 TEL : 886-3-327-3456 Report Version : Rev. 01 FAX : 886-3-327-0973 FCC Test Report Equipment : 11abgn 2x2 USB WiFi module Brand Name : Panasonic Model No. : DNUR-P1 FCC ID : NKR-P1 Standard : 47 CFR FCC Part 15.247 Operating Band : 2400 MHz – 2483.5 MHz Equipment Class : DTS Applicant Manufacturer : Wistron NeWeb Corporation 20 Park Avenue II, Hsinchu Science Park, Hsinchu 308,Taiwan,R.O.C. The product sample received on Nov. 27, 2012 and completely tested on Dec. 03, 2012. We, SPORTON, would like to declare that the tested sample has been evaluated in accordance with the procedures given in ANSI C63.10-2009 and shown compliance with the applicable technical standards. The test results in this report apply exclusively to the tested model / sample. Without written approval of SPORTON INTERNATIONAL INC., the test report shall not be reproduced except in full. Reviewed by: Wayne Hsu / Assistant Manager FCC Test Report Report No. : FR2N2717AC SPORTON INTERNATIONAL INC. Page No. : 2 of 64 TEL : 886-3-327-3456 Report Version : Rev. 01 FAX : 886-3-327-0973 Table of Contents 1 GENERAL DESCRIPTION .................................................................................................................... 5 1.1 Information .............................................................................................................................................. 5 1.2 Support Equipment ................................................................................................................................. 7 1.3 Testing Applied Standards ..................................................................................................................... 7 1.4 Testing Location Information .................................................................................................................. 7 1.5 Measurement Uncertainty ...................................................................................................................... 8 2 TEST CONFIGURATION OF EUT......................................................................................................... 9 2.1 The Worst Case Modulation Configuration ............................................................................................ 9 2.2 Test Channel Frequencies Configuration ............................................................................................... 9 2.3 The Worst Case Power Setting Parameter ............................................................................................ 9 2.4 The Worst Case Measurement Configuration ...................................................................................... 10 2.5 Test Setup Diagram ............................................................................................................................. 11 3 TRANSMITTER TEST RESULT .......................................................................................................... 12 3.1 AC Power-line Conducted Emissions .................................................................................................. 12 3.2 6dB Bandwidth ..................................................................................................................................... 15 3.3 RF Output Power .................................................................................................................................. 18 3.4 Power Spectral Density ........................................................................................................................ 24 3.5 Transmitter Radiated Bandedge Emissions ......................................................................................... 27 3.6 Transmitter Radiated Unwanted Emissions ......................................................................................... 33 4 TEST EQUIPMENT AND CALIBRATION DATA ................................................................................ 62 5 CERTIFICATION OF TAF ACCREDITATION ..................................................................................... 64 APPENDIX A. TEST PHOTOS ....................................................................................................................... A7 APPENDIX B. PHOTOGRAPHS OF EUT ...................................................................................................... B3 FCC Test Report Report No. : FR2N2717AC SPORTON INTERNATIONAL INC. Page No. : 3 of 64 TEL : 886-3-327-3456 Report Version : Rev. 01 FAX : 886-3-327-0973 Summary of Test Result Conformance Test Specifications Report Clause Ref. Std. Clause Description Measured Limit Result 1.1.2 15.203 Antenna Requirement Antenna connector mechanism complied FCC 15.203 Complied 3.1 15.207 AC Power-line Conducted Emissions [dBuV]: 17.470MHz 33.26 (Margin 16.74dB) - AV 39.15 (Margin 20.85dB) - QP FCC 15.207 Complied 3.2 15.247(a) 6dB Bandwidth 6dB Bandwidth Unit [MHz] 20M: 17.28 / 40M: 35.83 ≥500kHz Complied 3.3 15.247(b) RF Output Power (Maximum Peak Conducted Output Power) Power [dBm]: 29.81 Power [dBm]:30 Complied 3.4 15.247(d) Power Spectral Density PSD [dBm/3kHz]: -3.79 PSD [dBm/3kHz]:8 Complied 3.5 15.247(c) Transmitter Radiated Bandedge Emissions Non-Restricted Bands: 2397.14MHz: 26.36dB Restricted Bands [dBuV/m at 3m]: 2483.5MHz 60.64 (Margin 13.36dB) - PK 52.97 (Margin 1.03dB) - AV Non-Restricted Bands: > 20 dBc Restricted Bands: FCC 15.209 Complied 3.6 15.247(c) Transmitter Radiated Unwanted Emissions Restricted Bands [dBuV/m at 3m]: 480.08MHz 44.85 (Margin 1.15dB) - QP Non-Restricted Bands: > 20 dBc Restricted Bands: FCC 15.209 Complied FCC Test Report Report No. : FR2N2717AC SPORTON INTERNATIONAL INC. Page No. : 4 of 64 TEL : 886-3-327-3456 Report Version : Rev. 01 FAX : 886-3-327-0973 Revision History Report No. Version Description Issued Date FR2N2717AC Rev. 01 Initial issue of report Dec. 13, 2012 2500-2690 FCC Test Report…

Text truncated - open the document above for the full version.

FCC Test Report Report No. : FR2N2717AN SPORTON INTERNATIONAL INC. Page No. : 1 of 112 TEL : 886-3-327-456 Report Version : Rev. 01 FAX : 886-3-327-973 FCC Test Report Equipment : 11abgn 2x2 USB WiFi module Brand Name : Panasonic Model No. : DNUR-P1 FCC ID : NKR-P1 Standard : 47 CFR FCC Part 15.407 Operating Band : 5150 MHz – 5250 MHz 5250 MHz – 5350 MHz 5470 MHz – 5725 MHz Equipment Class : NII Applicant : Wistron NeWeb Corporation 20 Park Avenue II, Hsinchu Science Park, Hsinchu 308,Taiwan,R.O.C. Manufacturer : Wistron NeWeb Corporation 20 Park Avenue II, Hsinchu Science Park, Hsinchu 308,Taiwan,R.O.C. Operate Mode : Client without radar detection The product sample received on Nov. 27, 2012 and completely tested on Dec. 07, 2012. We, SPORTON, would like to declare that the tested sample has been evaluated in accordance with the procedures given in ANSI C63.10-2009 and shown compliance with the applicable technical standards. The test results in this report apply exclusively to the tested model / sample. Without written approval of SPORTON INTERNATIONAL INC., the test report shall not be reproduced except in full. Reviewed by: Wayne Hsu / Assistant Manager FCC Test Report Report No. : FR2N2717AN SPORTON INTERNATIONAL INC. Page No. : 2 of 112 TEL : 886-3-327-456 Report Version : Rev. 01 FAX : 886-3-327-973 Table of Contents 1 GENERAL DESCRIPTION .................................................................................................................... 5 1.1 Information .............................................................................................................................................. 5 1.2 DFS and TPC Information ...................................................................................................................... 7 1.3 Support Equipment ................................................................................................................................. 7 1.4 Testing Applied Standards ..................................................................................................................... 7 1.5 Testing Location Information .................................................................................................................. 7 1.6 Measurement Uncertainty ...................................................................................................................... 8 2 TEST CONFIGURATION OF EUT......................................................................................................... 9 2.1 The Worst Case Modulation Configuration ............................................................................................ 9 2.2 Test Channel Frequencies Configuration ............................................................................................... 9 2.3 The Worst Case Power Setting Parameter .......................................................................................... 10 2.4 The Worst Case Measurement Configuration ...................................................................................... 11 2.5 Test Setup Diagram ............................................................................................................................. 12 3 TRANSMITTER TEST RESULT .......................................................................................................... 13 3.1 AC Power-line Conducted Emissions .................................................................................................. 13 3.2 Emission Bandwidth ............................................................................................................................. 16 3.3 RF Output Power .................................................................................................................................. 22 3.4 Peak Power Spectral Density ............................................................................................................... 33 3.5 Peak Excursion..................................................................................................................................... 41 3.6 Transmitter Radiated Bandedge Emissions ......................................................................................... 43 3.7 Transmitter Radiated Unwanted Emissions ......................................................................................... 53 3.8 Frequency Stability ............................................................................................................................. 108 4 TEST EQUIPMENT AND CALIBRATION DATA .............................................................................. 110 5 CERTIFICATION OF TAF ACCREDITATION ................................................................................... 112 APPENDIX A. TEST PHOTOS ....................................................................................................................... A7 APPENDIX B. PHOTOGRAPHS OF EUT .........................................................…

Text truncated - open the document above for the full version.