NKR-S236802.11 abgn USB Module

SHARP Corp. RUNTKA863WJQZ 802.11 abgn USB Module User Manual Version: 1.0 1 Copyright Statement No part of this publication may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, whether electronic, mechanical, photocopying, recording or otherwise without the prior writing of the publisher. Windows ™ 98SE/2000/ME/XP are trademarks of Microsoft ® Corp. Pentium is trademark of Intel. All copyright reserved. 2 Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures: - Reorient or relocate the receiving antenna. - Increase the separation between the equipment and receiver. - Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. - Consult the dealer or an experienced radio/TV technician for help. FCC Caution: To assure continued compliance, (example - use only shielded interface cables when connecting to computer or peripheral devices) any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. IMPORTANT NOTE: T h is tra n sm itte r m u st n o t b e co -lo ca te d o r o p e ra t ing in co n ju n ctio n with a n y o th e r a n te n n a o r tr a n sm itte r. 3 For product available in the USA/Canada market, only channel 1~11 can be operated. Selection of other channels is not possible. This device is going to be operated in 5.15~5.25GHz frequency range, it is restricted in indoor environment only. IMPORTANT NOTE: Federal Communication Commission (FCC) Radiation Exposure Statement This EUT is compliance with SAR for general population/uncontrolled exposure limits in ANSI/IEEE C95.1-1999 and had been tested in accordance with the measurement methods and procedures specified in OET Bulletin 65 Supplement C. This equipment should be installed and operated with minimum distance 0.5 cm between the radiator & your body. 4 Table of Contents 1. INTRODUCTION 5 2. DRIVER/UTILITY INSTALLATION / UNINSTALLATION 6 2.1 INSTALLATION......................................................................................................... 6 2.2 ADDITIONAL SETUP PROCESSES............................................................................. 9 2.3 UNINSTALLATION.................................................................................................. 10 3. CONNECTING TO AN EXISTING NETWORK 11 4. CREATING AN AD HOC NEW NETWORK 16 5. MODIFYING A WIRELESS NETWORK 20 5.1 INFRASTRUCTURE MODE AND AD HOC MODE..................................................... 20 5.2 MODIFYING A WIRELESS NETWORK.................................................................... 21 5.3 DEFAULT SETTINGS WINDOWS XP ZERO-CONFIGURATION............................... 28 5.4 SUPER A/G SETTING..........................................................錯誤! 尚未定義書籤。 5 1. Introduction Thank you for purchasing the 802.11 abgn USB Module that provides the easiest way to wireless networking. This User Manual contains detailed instructions in the operation of this product. Please keep this manual for future reference. System Requirements
A laptop PC contains: - 32 MB memory or greater - 300 MHz processor or higher
Microsoft ® Win ™ 2000/ME/98 Second Edition/XP 6 2. Driver/Utility Installation / Uninstallation 2.1 Installation Note! The Installation Section in this User Manual describes the first-time installation for Windows. To re-install the driver, please first uninstall the previously installed driver. See Chapter 2.3 “Uninstallation” in this User Manual. Follow the steps below to complete the driver/utility installation: 1. Insert the Installation Software CD into the CD-Rom Drive. 2. Click “Next”. 3. Read the License Agreement and click “Yes”. 7 4. Click “Next” to continue or click “Browse” to choose a destination folder. 5. Click “Next”. 6. Click “Yes” to create a shortcut icon on your desktop. 8 7. Click “Finish”. 8. You should now see a shortcut icon on your desktop. 9 2.2 Additional Setup Processes During software installation procedure, each operating system may prompt different specific options: 1. Windows 98SE: The system will request the original Windows CD during the installation process. When the installation is finished, you’ll have to restart your computer. 2. Windows Me: Please restart your computer when the installation is finished. 3. Windows 2000/XP: Select “Install the software automatically” when the window with this option appears, and then click “Next” to continue installation. 10 2.3 Uninstallation Note! Before uninstallation, please close all running programs. 1. Click Start>Programs>802.11 abgn USB Module >UnInstall 802.11 abgn USB Module . 2. Choose “Remove”. Click “Next”. 3. Click “OK” to start Uninstall. 4. Click “Finish”. Uninstall is now completed. 11 3. Connecting to an Existing Network 1. Double click the shortcut icon of 802.11 abgn USB Module on the desktop, and the Configuration window a…

Text truncated - open the document above for the full version.

DFS client device channel plan and software operational declaration Date: 2013-11-08 We, Wistron NeWeb Corp., declare that the device, FCC ID: NKR-S236 Model Name: RUNTKA863WJQZ, does not have “Ad Hoc on non-US frequencies” and/or “on DFS frequencies. Also, the client software and associated drivers will not initiate any transmission on DFS frequencies without initiation by a master. This includes restriction on transmissions for beacons and support for ad-hoc peer-to-peer modes. Below is the channel / frequency plan for the device Also, on DFS channels, the WLAN driver in the device operates under the control of an AP at all times, except when in ad-hoc mode, on US non-DFS channels. The device passively scans DFS frequencies until a master device is detected. The control of this functionality is not accessible to anyone under any conditions. Furthermore, the firmware is protected by special signature and CRC checksum. Signature and CRC checksum will be calculated and verified before firmware upgrade. Unauthorized modification to firmware will lead the failure of verification thus firmware upgrade is not allowed. Sincerely yours, ----------------------------------- Alan Wang / Senior Engineer Wistron NeWeb Corp. Tel: 886-3-6667799 Ext 6907 Fax: 886-3-6667323 E-mail: [email protected] CH 1 2 3 4 5 6 7 8 9 10 11 Frequency (MHz) 2412 2417 2422 2427 2432 2437 2442 2447 2452 2457 2462 Scan Type Active Active Active Active Active Active Active Active Active Active Active CH 36 38 40 42 44 48 52 54 56 58 60 Frequency (MHz) 5180 5190 5200 5210 5220 5240 5260 5270 5280 5290 5300 Scan Type Active Active Active Active Active Active Passive Passive Passive Passive Passive CH 62 64 Frequency (MHz) 5310 5320 Scan Type Passive Passive CH 100 102 104 106 108 110 112 116 132 134 136 Frequency (MHz) 5500 5510 5520 5530 5540 5550 5560 5580 5660 5670 5680 Scan Type Passive Passive Passive Passive Passive Passive Passive Passive Passive Passive Passive CH 140 Frequency (MHz) 5700 Scan Type Passive CH 149 151 153 155 157 159 161 165 Frequency (MHz) 5745 5755 5765 5775 5785 5795 5805 5825 Scan Type Active Active Active Active Active Active Active Active

FCC ID: NKR-S236 Date: 2013-11-08 Federal Communications Commission Authorization and Evaluation Division Confidentiality Request Pursuant to Sections 0.457 and 0.459 of the Commission’s Rules, the Applicant hereby requests confidential treatment of information accompanying this Application as outlined below: Schematics Block Diagram The above materials contain trade secrets and proprietary information not customarily released to the public. The public disclosure of these matters might be harmful to the Applicant and provide unjustified benefits to its competitors. The Applicant understands that pursuant to Rule 0.457, disclosure of this Application and all accompanying documentation will not be made before the date of the Grant for this application. Sincerely, ______________________ _____ Alan Wang / Senior Engineer Wistron NeWeb Corp. Tel: 886-3-6667799 Ext 6907 Fax: 886-3-6667323 E-mail: [email protected]

A G E N C Y A U T H O R I Z A T I O N L E T T E R FCC ID: NKR-S236 Date: 2013-11-08 To whom it may concern: We, the undersigned, hereby authorize Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch (BV CPS Taoyuan) of Taiwan to act on our behalf, as our agent, in the following matters related to the FCC approval of our products: report submittal, related correspondence, the signing of all documents relating to these matters, and any other lawful activity necessary to obtain such certification. Any act carried out by BV CPS Taoyuan within the scope of this authorization shall have the same effects as our own. This authorization shall expire 6 months from original date. If you have any questions regarding the authorization, please don’t hesitate to contact us. Thank you. Sincerely, ____________ _______________ Alan Wang / Senior Engineer Wistron NeWeb Corp. Tel: 886-3-6667799 Ext 6907 Fax: 886-3-6667323 E-mail: [email protected]

A G E N C Y A U T H O R I Z A T I O N L E T T E R Date: 2013-08-30 I, Troy Chien, am Associate Technical Director for Wistron NeWeb Corp. hereby authorize the following to act on our behalf, as our agent, in all matters relating to all processes required according to FCC approval for Wistron NeWeb Corp. products (Grantee Code: NKR) Barry Chen Alan Wang Lulu Lin This authorization shall expire twelve months from the original date. If you have any questions regarding the authorization, please don’t hesitate to contact us. Thank you! , Sincerely yours, Troy Chien / Associate technical director Wistron NeWeb Corp. Tel: 886-3-6667799 Ext 6361 Fax: 886-3-6667323 E-mail: [email protected]

FCC ID: NKR-S236 Report No.: RF131024C11 Modular Approval Request Letter Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch December 3, 2013 Dear Application Examiner, Wistron NeWeb Corp., 802.11 abgn USB Module, FCC ID: NKR-S236 would like to have your authorization as a modular approval specific to the mobile RF exposure condition. The requirements of Public Notice DA00-1407 have been met and shown on the following statements. 1. “The modular transmitter must have its own RF shielding.” The radio portion of this module has been shielded, please see exhibition External Photo. 2. “The modular transmitter must have buffered modulation/data inputs.” The EUT has buffered data inputs; it is integrated in chip BCM43236. 3. “The modular transmitter must have its own power supply regulation.” The part number of this regulator is BCM43236. 4. “The modular transmitter must comply with the antenna requirements of section 15.203 and 15.204(C).” The EUT meets the FCC antenna requirements. The spurious emission, unique antenna connector and photo of antennas are shown in the test report. 5. “The modular transmitter must be tested in a stand-alone configuration” The EUT was tested in a stand-alone configuration via a USB extender. Please see section Photographs of Test Configuration in the test report, the EUT was plugged in this extender. 6. “The modular transmitter must be labeled with its own FCC ID number.” Please see exhibition Label Sample for the FCC ID of this module. And also in the exhibition Users Manual, there are instructions give to the OEM on how to label the end product. FCC ID: NKR-S236 Report No.: RF131024C11 7. “The modular transmitter must comply with any specific rule or operating requirements applicable to the transmitter and the manufacturer must provide adequate instructions along with the module to explain any such requirements.” The EUT is compliant with all applicable FCC rules. Detail instructions for maintaining compliance are given in the Users Manual. 8. “The modular transmitter must comply with any applicable RF exposure requirements.” The EUT is compliant with all applicable RF exposure requirements. RF Exposure is addressed in the RF exposure exhibition. Please contact me if you have any further questions. Thanks for your attention. Best Regards, Robert Huang Senior Engineer Bureau Veritas Consumer Products Services (H.K.) Ltd., Hsinchu Branch

Page 1 CONSTRUCTION PHOTOS OF EUT

Label location

REVAPPROVEDDATE REV SIZE DWG TITLE DWG NO. SCALESHEET REV A4A4 A 1/1 1 OF 2 SANDY CHEN HSINYUN LIN HSINYUN LIN 10/23/13 10/23/13 10/23/13 10/23/13 SANDY CHEN AA RELEASE TO FILE 4L-DNUB103-011 4L-DNUB103-011 DESCRIPTION REVISIONS PART NUMBER BLOCK PART NUMBER LABEL, WHITE, 18.5X15.0, DNUB-S236LABEL, WHITE, 18.5X15.0, DNUB-S236 WNC PROPRIETARY 15.0 18.5 NOTES: 1. MATERIAL: WHITE MATT PET, t=0.05, 壓克力背膠 2. COLOR: a. 底色為材質原色 3. TEMPERATURE RESISTANT= 80 0 C. 4. ADHESIVE THICKNESS=0.024±0.003mm. 5. 貼於ABS塑膠(凹槽) 6. PRODUCT LABEL 參照第二頁相關測試規範 7. 捲狀進料 DNUB-S236 20 Park Avenue II, Hsinchu Science Park, Hsinchu 308, Taiwan, R.O.C. Tel: 886-3-6667799 Fax: 886-3-5788726 ON LINE PRINTING FCC ID : NKR-S236 IC : 4441A-S236 Model : RUNTKA863WJQZ (DNUB-S236) MAC ID : XXXXXXXXXXXX MADE IN CHINA 201WW11215030 201XW11215031 201YW11215032 D110186003 FCC ID : NKR-S236 IC : 4441A-S236 Model : RUNTKA863WJQZ (DNUB-S236) MAC ID : XXXXXXXXXXXX MADE IN CHINA 201WW11215030 201XW11215031 201YW11215032 D110186003

Page 2

FCC ID: NKR-S236 Report No.: RF131024C11 Operational Description This device is a 802.11 abgn USB Module, which operates in both of 2.4GHz and 5GHz bands; the maximum data rate could be up to 300Mbps which OFDM technique. If the signal to noise radio is too poor which could not support 300Mbps, the 11Mbps data rate with DSSS technique will be applied. The transmitter of the EUT is powered by the 5Vdc from host equipment. The antenna is Printed antenna without antenna connector. The other instruction, please have a look at the user’s manual. FCC 15.407(c) states: The device shall automatically discontinue transmission in case of either absence of information to transmit or operational failure. These provisions are not intended to preclude the transmission of control or signaling information or the use of repetitive codes used by certain digital technologies to complete frame or burst intervals. Applicants shall include in their application for equipment authorization a description of how this requirement is met” Data transmission is always initiated by software, which is then pass down through the MAC, through the digital and analog baseband, and finally to the RF chip. Several special packets (ACKs, CTS, PSPoll, etc...) are initiated by the MAC. There are the only ways the digital baseband portion will turn on the RF transmitter, which it then turns off at the end of the packet. Therefore, the transmitter will be on only while one of the aforementioned packets are being transmitted.

Report No.: SA110209C16B 1 of 6 Report Format Version 5.0.0 Reference No.: 131024C11 RF EXPOSURE REPORT REPORT NO.: SA110209C16B MODEL NO.: RUNTKA863WJQZ FCC ID: NKR-S236 RECEIVED: Oct. 24, 2013 TESTED: Nov. 15 ~ Nov. 20, 2013 ISSUED: Nov. 27, 2013 APPLICANT: Wistron NeWeb Corp. ADDRESS: 20 Park Avenue II, Hsinchu Science Park,Hsinchu 30076, Taiwan, R.O.C. ISSUED BY: Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch LAB ADDRESS: No. 47, 14th Ling, Chia Pau Vil., Lin Kou Dist., New Taipei City, Taiwan, R.O.C. TEST LOCATION: No. 19, Hwa Ya 2nd Rd, Wen Hwa Tsuen, Kwei Shan Hsiang, Taoyuan Hsien 333, Taiwan, R.O.C. This report is for your exclusive use. Any copying or replication of this report to or for any other person or entity, or use of our name or trademark, is permitted only with our prior written permission. This report sets forth our findings solely with respect to the test samples identified herein. The results set forth in this report are not indicative or representative of the quality or characteristics of the lot from which a test sample was taken or any similar or identical product unless specifically and expressly noted. Our report includes all of the tests requested by you and the results thereof based upon the information that you provided to us. You have 60 days from date of issuance of this report to notify us of any material error or omission caused by our negligence, provided, however, that such notice shall be in writing and shall specifically address the issue you wish to raise. A failure to raise such issue within the prescribed time shall constitute your unqualified acceptance of the completeness of this report, the tests conducted and the correctness of the report contents. Unless specific mention, the uncertainty of measurement has been explicitly taken into account to declare the compliance or non-com pliance to the specification. This report should not be used by the client to claim product certification, approval, or endorsement by any government agencies. Report No.: SA110209C16B 2 of 6 Report Format Version 5.0.0 Reference No.: 131024C11 TABLE OF CONTENTS RELEASE CONTROL RECORD .................................................................................................. 3 1. CERTIFICATION ............................................................................................................... 4 2. RF EXPOSURE ................................................................................................................. 5 2.1 LIMITS FOR MAXIMUM PERMISSIBLE EXPOSURE (MPE) ........................................... 5 2.2 MPE CALCULATION FORMULA ...................................................................................... 5 2.3 CLASSIFICATION ............................................................................................................. 5 2.4 CALCULATION RESULT OF MAXIMUM CONDUCTED POWER .................................... 6 Report No.: SA110209C16B 3 of 6 Report Format Version 5.0.0 Reference No.: 131024C11 RELEASE CONTROL RECORD ISSUE NO. REASON FOR CHANGE DATE ISSUED SA110209C16B Original release. Nov. 27, 2013 Report No.: SA110209C16B 4 of 6 Report Format Version 5.0.0 Reference No.: 131024C11 1. CERTIFICATION PRODUCT: 802.11 abgn USB Module MODEL NO.: RUNTKA863WJQZ BRAND: SHARP Corporation APPLICANT: Wistron NeWeb Corp. TESTED: Nov. 15 ~ Nov. 20, 2013 TEST SAMPLE: ENGINEERING SAMPLE STANDARDS: FCC Part 2 (Section 2.1091) FCC OET Bulletin 65, Supplement C (01-01) IEEE C95.1 The above equipment (Model: RUNTKA863WJQZ) has been tested by Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch, and found compliance with the requirement of the above standards. The test record, data evaluation & Equipment Under Test (EUT) configurations represented herein are true and accurate accounts of the measurements of the sample’s EMC characteristics under the conditions specified in this report. PREPARED BY : , DATE : Nov. 27, 2013 Suntee Liu / Specialist APPROVED BY : , DATE : Nov. 27, 2013 Ken Liu / Senior Manager Report No.: SA110209C16B 5 of 6 Report Format Version 5.0.0 Reference No.: 131024C11 2. RF EXPOSURE 2.1 LIMITS FOR MAXIMUM PERMISSIBLE EXPOSURE (MPE) FREQUENCY RANGE (MHz) ELECTRIC FIELD STRENGTH (V/m) MAGNETIC FIELD STRENGTH (A/m) POWER DENSITY (mW/cm 2 ) AVERAGE TIME (minutes) LIMITS FOR GENERAL POPULATION / UNCONTROLLED EXPOSURE 300-1500 ... ... F/1500 30 1500-100,000 ... ... 1.0 30 F = Frequency in MHz 2.2 MPE CALCULATION FORMULA Pd = (Pout*G) / (4*pi*r 2 ) where Pd = power density in mW/cm 2 Pout = output power to antenna in mW G = gain of antenna in linear scale Pi = 3.1416 R = distance between observation point and center of the radiator in cm 2.3 CLASSIFICATION The antenna of this product, under normal use condition, is at least 20cm away from the body of the user. So, this device is classified as Mobile Device. Report No.: SA110209C16B 6 of 6 Report Format Version 5.0.0 Reference No.: 131024C11 2.4 CALCULATION RESULT OF MAXIMUM CONDUCTED POWER FREQUENCY BAND (MHz) MAX POWER (dBm) ANTENNA GAIN (dBi) DISTANCE (cm) POWER DENSITY (mW/cm 2 ) LIMIT (mW/cm 2 ) 2412-2462 27.86 1.85 20 0.186 1 5180-5240 16.27 2.15 20 0.014 1 5260-5320 16.22 2.24 20 0.014 1 5500-5700 16.41 2.12 20 0.014 1 5745-5825 24.70 1.23 20 0.078 1 ---END---

Report No.: RF110209C16B-2 1 of 25 Report Format Version 5.0.0 Reference No.: 131024C11 DFS TEST REPORT REPORT NO.: RF110209C16B-2 MODEL NO.: RUNTKA863WJQZ FCC ID: NKR-S236 RECEIVED: Oct. 24, 2013 TESTED: Nov. 15 ~ Nov. 20, 2013 ISSUED: Nov. 27, 2013 APPLICANT: Wistron NeWeb Corp. ADDRESS: 20 Park Avenue II, Hsinchu Science Park,Hsinchu 30076, Taiwan, R.O.C. ISSUED BY: Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch LAB ADDRESS: No. 47, 14th Ling, Chia Pau Vil., Lin Kou Dist., New Taipei City, Taiwan, R.O.C. TEST LOCATION: No. 19, Hwa Ya 2nd Rd, Wen Hwa Tsuen, Kwei Shan Hsiang, Taoyuan Hsien 333, Taiwan, R.O.C. This report is for your exclusive use. Any copying or replication of this report to or for any other person or entity, or use of our name or trademark, is permitted only with our prior written permission. This report sets forth our findings solely with respect to the test samples identified herein. The results set forth in this report are not indicative or representative of the quality or characteristics of the lot from which a test sample was taken or any similar or identical product unless specifically and expressly noted. Our report includes all of the tests requested by you and the results thereof based upon the information that you provided to us. You have 60 days from date of issuance of this report to notify us of any material error or omission caused by our negligence, provided, however, that such notice shall be in writing and shall specifically address the issue you wish to raise. A failure to raise such issue within the prescribed time shall constitute your unqualified acceptance of the completeness of this report, the tests conducted and the correctness of the report contents. Unless specific mention, the uncertainty of measurement has been explicitly taken into account to declare the com pliance or non-compliance to the specification. This report should not be used by the client to claim product certification, approval, or endorsement by TAF or any government agencies. Report No.: RF110209C16B-2 2 of 25 Report Format Version 5.0.0 Reference No.: 131024C11 TABLE OF CONTENTS RELEASE CONTROL RECORD .............................................................................................................. 3 1. CERTIFICATION .......................................................................................................................... 4 2. EUT INFORMATION .................................................................................................................... 5 2.1 OPERATING FREQUENCY BANDS AND MODE OF EUT ........................................................ 5 2.2 EUT SOFTWARE AND FIRMWARE VERSION .......................................................................... 5 2.3 DESCRIPTION OF AVAILABLE ANTENNAS TO THE EUT ....................................................... 5 2.4 EUT MAXIMUM CONDUCTED POWER .................................................................................... 6 2.5 EUT MAXIMUM E.I.R.P. POWER ................................................................................................ 7 2.6 TRANSMIT POWER CONTROL (TPC) ....................................................................................... 8 2.7 STATEMENT OF MAUNFACTURER .......................................................................................... 8 3. U-NII DFS RULE REQUIREMENTS ........................................................................................... 9 3.1 WORKING MODES AND REQUIRED TEST ITEMS .................................................................. 9 3.2 TEST LIMITS AND RADAR SIGNAL PARAMETERS ............................................................... 10 4. TEST & SUPPORT EQUIPMENT LIST ..................................................................................... 12 4.1 TEST INSTRUMENTS ............................................................................................................... 12 4.2 DESCRIPTION OF SUPPORT UNITS ...................................................................................... 12 5. TEST PROCEDURE .................................................................................................................. 13 5.1 BV ADT DFS MEASUREMENT SYSTEM ................................................................................. 13 5.2 CALIBRATION OF DFS DETECTION THRESHOLD LEVEL ................................................... 14 5.3 DEVIATION FROM TEST STANDARD ..................................................................................... 15 5.4 RADIATED TEST SETUP CONFIGURATION ........................................................................... 15 5.4.1 CLIENT WITHOUT RADAR DETECTION MODE ..................................................................... 15 6. TEST RESULTS ........................................................................................................................ 16 6.1 SUMMARY OF TEST RESULTS ............................................................................................... 16 6.2 DETELED TEST RESULTS ....................................................................................................... 17 6.2.1 TEST MODE: DEVICE OPERATING IN CLIENT WITHOUT RADAR DETECTION MODE ..... 17 6.2.2 CHANNEL CLOSING TRANSMISSION AND CHANNEL MOVE TIME .................................... 18 6.2.3 NON-OCCUPANCY PERIOD .................................................................................................... 20 6.2.4 NON-ASSOCIATED TEST ........................................................................................................ 22 6.2.5 NON- CO-CHANNEL TEST ....................................................................................................... 22 7. PHOTOGRAPHS OF THE TEST CONFIGURATION ............................................................... 23 8. INFORMATION ON THE TESTING LABORATORIES .........................................…

Text truncated - open the document above for the full version.

Report No.: RF110209C16B 1 of 92 Report Format Version 5.2.0 Reference No.: 131024C11 FCC TEST REPORT (15.247) REPORT NO.: RF110209C16B MODEL NO.: RUNTKA863WJQZ FCC ID: NKR-S236 RECEIVED: Oct. 24, 2013 TESTED: Nov. 15 ~ Nov. 20, 2013 ISSUED: Nov. 27, 2013 APPLICANT: Wistron NeWeb Corp. ADDRESS: 20 Park Avenue II, Hsinchu Science Park,Hsinchu 30076, Taiwan, R.O.C. ISSUED BY: Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch LAB ADDRESS: No. 47, 14th Ling, Chia Pau Vil., Lin Kou Dist., New Taipei City, Taiwan, R.O.C. TEST LOCATION: No. 19, Hwa Ya 2nd Rd, Wen Hwa Tsuen, Kwei Shan Hsiang, Taoyuan Hsien 333, Taiwan, R.O.C. This report is for your exclusive use. Any copying or replication of this report to or for any other person or entity, or use of our name or trademark, is permitted only with our prior written permission. This report sets forth our findings solely with respect to the test samples identified herein. The results set forth in this report are not indicative or representative of the quality or characteristics of the lot from which a test sample was taken or any similar or identical product unless specifically and expressly noted. Our report includes all of the tests requested by you and the results thereof based upon the information that you provided to us. You have 60 days from date of issuance of this report to notify us of any material error or omission caused by our negligence, provided, however, that such notice shall be in writing and shall specifically address the issue you wish to raise. A failure to raise such issue within the prescribed time shall constitute your unqualified acceptance of the completeness of this report, the tests conducted and the correctness of the report contents. Unless specific mention, the uncertainty of measurement has been explicitly taken into account to declare the com pliance or non-compliance to the specification. This report should not be used by the client to claim product certification, approval, or endorsement by TAF or any government agencies. Report No.: RF110209C16B 2 of 92 Report Format Version 5.2.0 Reference No.: 131024C11 TABLE OF CONTENTS RELEASE CONTROL RECORD .............................................................................................................. 5 1. CERTIFICATION ....................................................................................................................... 6 2. SUMMARY OF TEST RESULTS .............................................................................................. 7 2.1 MEASUREMENT UNCERTAINTY ............................................................................................ 7 3. GENERAL INFORMATION ....................................................................................................... 8 3.1 GENERAL DESCRIPTION OF EUT ......................................................................................... 8 3.2 DESCRIPTION O…

Text truncated - open the document above for the full version.