NKR-TR1V1-IDUVerizon 5G Extender

Verizon 5G Extender TR1V1 User Guide Version 1 i Federal Communication Commission Interference Statement This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures: • Reorient or relocate the receiving antenna. • Increase the separation between the equipment and receiver. • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. • Consult the dealer or an experienced radio/TV technician for help. FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. WARNING. This is NOT a CONSUMER device. It is designed for installation by FCC LICENSEES and QUALIFIED INSTALLERS. You MUST have an FCC LICENSE or express consent of an FCC Licensee to operate this device. Unauthorized use may result in significant forfeiture penalties, including penalties in excess of $100,000 for each continuing violation. ii RF Exposure Statement To comply with FCC RF exposure compliance requirements, the antenna used for this transmitter must be installed to provide a separation distance of at least 32 cm from all persons and must not be co-located or operating in conjunction with any other antenna or transmitter. iii Table of Contents Chapter 1 Introduction ..................................................................................................................................... 1 1.1 Unboxing Information........................................................................................................................... 1 1.2 Front Panel ............................................................................................................................................ 2 1.3 Back Panel ............................................................................................................................................ 3 1.4 Bottom Panel ........................................................................................................................................ 4 1.5 Side Panel ............................................................................................................................................. 4 1.6 Mounting Bracket ................................................................................................................................. 5 Chapter 2 Mounting the 5G Extender ........................................................................................................... 7 2.1 Window Mounting ................................................................................................................................. 7 2.2 Wall Mounting ....................................................................................................................................... 9 Chapter 3 Product Specifications................................................................................................................ 12 1 Chapter 1 Introduction This chapter includes a list of items included with the TR1V1 5G Extender and a description of the user interface and ports on the device. 1.1 Unboxing Information Inside the product package for the TR1V1 5G Extender, you should find the following items: • Extender • AC adapter • Window mounting bracket • One alcohol swab • Cable ties • Cable clips (with adhesive) • Window wedges (with adhesive) • Anchors and metal screws for wall mounting • Installation location labels (with adhesive) 2 1.2 Front Panel An LED indicator is located in the top-left corner of the Extender’s front panel. LED Light Guide Device Status Description LED Status Booting up The Extender is powered and in the process of booting up. Solid: White Ready to pair The Extender is ready to be paired with the 5G nodes. Blinking: Blue Ready to scan The Extender is connected to the 5G nodes. Solid: Blue Scanning The Extender is scanning the signal strength from the 5G nodes. Soft Blink: White Paired: Good Signal The signal strength from the 5G nodes is good. Solid: Green Paired: Poor Signal The signal strength from the 5G nodes is poor. Solid: Yellow 3 Paired: No/Bad Signal There is no signal from the 5G nodes. Solid: Red Regular usage The Extender is working normally. Off Error An error has occurred (ex. pairing/FW issue) Blinking: Red FW Update / Reset The Extender is ready to reboot after a FW update. Fast Blink: White (Occurs during the 2 seconds prior to reboot/power off) 1.3 Back Panel 1. Product label and QR code Scan the QR code on this label with the Installer app to enable the receiver to establish a connection with the Extender. 2. Mounting head The mounting head fits into the installation slot on the mounting bracket. 4 1.4 Bottom Panel 1. DC jack Plug the AC adapter into this jack to power the Extender. 2. Screw holes The securing screw for the mounting bracket should be fastened into one of …

Text truncated - open the document above for the full version.

Reference No.: 200130C10-1 Page No. 1 / 5 CONSTRUCTION PHOTOS OF EUT Reference No.: 200130C10-1 Page No. 2 / 5 Reference No.: 200130C10-1 Page No. 3 / 5 Reference No.: 200130C10-1 Page No. 4 / 5 Reference No.: 200130C10-1 Page No. 5 / 5

Rear - Label Without the bracket Label location Label location

ANEW RELEASE WNC CONFIDENTIAL A 2 AMANDA LAI03/27/20 03/27/20 03/27/20 AMANDA LAI SAM SUN 1/1 1 OF 1 DIE LINE (DO NOT PRINT) PMS COOL GREY 5C LV11 PRIMARY GARY() LABEL, FCC WARNING, UPDATED, TR1 NOTES: 1. MATERIAL: PET, t=0.075 ADHESIVE: FINISH: PET, T=0.025 2. COLOR: LV11 PRIMARY GARY,PMS COOL GREY 5C 3. 4. 3±0.5MM,3.0±0.3MM 5. :ABS 6. :30mm±0.3mm,120~315mm±0.5mm,315±0.8mm 7. TEST REQUIREMENT TEST I TEMTEST SPECTEST CONDITIONCR ITER IA 1 附著力測 試 ISO Class.: 1 ASTM Class.: 4 B ASTM D3359-02/ ISO 2409:2007 Det achment of smal l fl akes of the coat ing at the inter sections of the cuts. A cross-cut ar ea not signifi cantly greater than 5 % is affected. 03/27/20SAM SUN 4L.TR100.00401 WARNING. This is NOT a CONSUMER device. It is designed for installation by FCC LICENSEES and QUALIFIED INSTALLERS. You MUST have an FCC LICENSE or express consent of an FCC Licensee to operate this device. Unauthorized use may result in significant forfeiture penalties, including penalties in excess of $100,000 for each continuing violation. FCC ID: NKR-TR1V1-IDU WARNING. This is NOT a CONSUMER device. It is designed for installation by FCC LICENSEES and QUALIFIED INSTALLERS. You MUST have an FCC LICENSE or express consent of an FCC Licensee to operate this device. Unauthorized use may result in significant forfeiture penalties, including penalties in excess of $100,000 for each continuing violation. FCC ID: NKR-TR1V1-IDU WARNING. This is NOT a CONSUMER device. It is designed for installation by FCC LICENSEES and QUALIFIED INSTALLERS. You MUST have an FCC LICENSE or express consent of an FCC Licensee to operate this device. Unauthorized use may result in significant forfeiture penalties, including penalties in excess of $100,000 for each continuing violation. FCC ID: NKR-TR1V1-IDU 29.6 22.7 *1 *2 1.3±0.5 1.3±0.5 3 4

Reference No.: 200130C10-2 Page No. 1 / 13 CONSTRUCTION PHOTOS OF EUT Reference No.: 200130C10-2 Page No. 2 / 13 Reference No.: 200130C10-2 Page No. 3 / 13 Reference No.: 200130C10-2 Page No. 4 / 13 Reference No.: 200130C10-2 Page No. 5 / 13 Reference No.: 200130C10-2 Page No. 6 / 13 Reference No.: 200130C10-2 Page No. 7 / 13 Reference No.: 200130C10-2 Page No. 8 / 13 Reference No.: 200130C10-2 Page No. 9 / 13 Reference No.: 200130C10-2 Page No. 10 / 13 Reference No.: 200130C10-2 Page No. 11 / 13 Reference No.: 200130C10-2 Page No. 12 / 13 Reference No.: 200130C10-2 Page No. 13 / 13

Report No.: SA200130C10A Page No. 1 / 6 Report Format Version: 6.1.1 Reference No.: 200327C32 RF Exposure Report Report No.: SA200130C10A FCC ID: NKR-TR1V1-IDU Test Model: TR1V1 Received Date: Jan. 31, 2020 Test Date: Feb. 06 ~ Mar. 11, 2020 Issued Date: Mar. 30, 2020 Applicant: Wistron NeWeb Corp. Address: 20 Park Avenue II, Hsinchu Science Park, Hsinchu 308, Taiwan, R.O.C. Issued By: Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch Lin Kou Laboratories Lab Address: No. 47-2, 14th Ling, Chia Pau Vil., Lin Kou Dist., New Taipei City, Taiwan Test Location: No. 19, Hwa Ya 2nd Rd., Wen Hwa Vil., Kwei Shan Dist., Taoyuan City 33383, Taiwan FCC Registration / Designation Number: 788550 / TW0003 This report is for your exclusive use. Any copying or replication of this report to or for any other person or entity, or use of our name or trademark, is permitted only with our prior written permission. This report sets forth ourfindings solely with respect to the test samples identified herein. The results set forth in this report are not indicative or representative of the quality or characteristics of the lot from which a test sample was taken or any similar or identical product unless specifically and expressly noted. Our report includes all of the tests requested by you and the results thereof based upon the information that you provided to us. You have 60 days from date of issuance of this report to notify us of any material error or omission caused by our negligence, provided, however, that such notice shall be in writing and shall specifically address the issue you wish to raise. A failure to raise such issue within the prescribed time shall constitute your unqualified acceptance of the completeness of this report, the tests conducted and the correctness of the report contents. Unless specific mention, the uncertainty of measurement has been explicitly taken into account to declare the compliance or non-compliance to the specification. The report must not be used by the client to claim product certification, approval, or endorsement by TAF or any government agencies. Report No.: SA200130C10A Page No. 2 / 6 Report Format Version: 6.1.1 Reference No.: 200327C32 Table of Contents Release Control Record .................................................................................................................................. 3 1 Certificate of Conformity ...................................................................................................................... 4 2 RF Exposure .......................................................................................................................................... 5 2.1 Limits for Maximum Permissible Exposure (MPE) .............................................................................. 5 2.2 MPE Calculation Formula ................................................................................................................... 5 2.3 Classification ....................................................................................................................................... 5 3 Calculation Result of Maximum Conducted Power ........................................................................... 6 Report No.: SA200130C10A Page No. 3 / 6 Report Format Version: 6.1.1 Reference No.: 200327C32 Release Control Record Issue No. Description Date Issued SA200130C10A Original release Mar. 30, 2020 Report No.: SA200130C10A Page No. 4 / 6 Report Format Version: 6.1.1 Reference No.: 200327C32 1 Certificate of Conformity Product: Verizon 5G Extender Brand: Verizon Test Model: TR1V1 Sample Status: Engineering sample Applicant: Wistron NeWeb Corp. Test Date: Feb. 06 ~ Mar. 11, 2020 Standards: FCC Part 2 (Section 2.1091) IEEE C95.3 -2002 References Test Guidance: KDB 447498 D01 General RF Exposure Guidance v06 The above equipment has been tested by Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch, and found compliance with the requirement of the above standards. The test record, data evaluation & Equipment Under Test (EUT) configurations represented herein are true and accurate accounts of the measurements of the sample’s RF characteristics under the conditions specified in this report. Prepared by : , Date:Mar. 30, 2020 Pettie Chen / Senior Specialist Approved by : , Date:Mar. 30, 2020 Bruce Chen / Senior Project Engineer Report No.: SA200130C10A Page No. 5 / 6 Report Format Version: 6.1.1 Reference No.: 200327C32 2 RF Exposure 2.1 Limits for Maximum Permissible Exposure (MPE) Frequency Range (MHz) Electric Field Strength (V/m) Magnetic Field Strength (A/m) Power Density (mW/cm 2 ) Average Time (minutes) Limits For General Population / Uncontrolled Exposure 0.3-1.34 614 1.63 (100)* 30 1.34-30 824/f 2.19/f (180/f 2 )* 30 30-300 27.5 0.073 0.2 30 300-1500 ... ... f/1500 30 1500-100,000 ... ... 1.0 30 f = Frequency in MHz; *Plane-wave equivalent power density 2.2 MPE Calculation Formula Pd = (Pout*G) / (4*pi*r 2 ) where Pd = power density in mW/cm 2 Pout = output power to antenna in mW G = gain of antenna in linear scale pi = 3.1416 r = distance between observation point and center of the radiator in cm 2.3 Classification The antenna of this product, under normal use condition, is at least 32cm away from the body of the user. So, this device is classified as Mobile Device. Report No.: SA200130C10A Page No. 6 / 6 Report Format Version: 6.1.1 Reference No.: 200327C32 3 Calculation Result of Maximum Conducted Power Mode Max Power (dBm) Antenna Gain (dBi) Distance (cm) Power Density (mW/cm 2 ) Limit (mW/cm 2 ) BT LE 10.63 4 32 0.002 1 Mode Frequency Band EIRP (dBm) Distance (cm) Power Density (mW/cm 2 ) Limit (mW/cm 2 ) Relay 27.5 GHz ~ 28.35 GHz 24.36 32 0.021 1 Donor 27.5 GHz ~ 28.35 GHz 41.06 32 0.992 1 Note: Determining compliance based on the results of the compliance measurement, not taking into account measurement instrumentation uncertainty. Conclusion: BT LE and Relay or Donor can tra…

Text truncated - open the document above for the full version.

Report No.: RF200130C10-1 Page No. 1 / 358 Report Format Version: 6.1.1 FCC Test Report (Part 20 / Part 30) Report No.: RF200130C10-1 FCC ID: NKR-TR1V1-IDU Test Model: TR1V1 Received Date: Jan. 31, 2020 Test Date: Feb. 22 ~ Mar. 11, 2020 Issued Date: Mar. 13, 2020 Applicant: Wistron NeWeb Corp. Address: 20 Park Avenue II, Hsinchu Science Park, Hsinchu 308, Taiwan, R.O.C. Issued By: Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch Lin Kou Laboratories Lab Address: No. 47-2, 14th Ling, Chia Pau Vil., Lin Kou Dist., New Taipei City, Taiwan Test Location: No. 19, Hwa Ya 2nd Rd., Wen Hwa Vil., Kwei Shan Dist., Taoyuan City 33383, Taiwan FCC Registration / Designation Number: 788550 / TW0003 This report is for your exclusive use. Any copying or replication of this report to or for any other person or entity, or use of our name or trademark, is permitted only with our prior written permission. This report sets forth our findings solely with respect to the test samples identified herein. The results set forth in this report are not indicative or representative of the quality or characteristics of the lot from which a test sample was taken or any similar or identical product unless specifically and expressly noted. Our report includes all of the tests requested by you and the results thereof based upon the information that you provided to us. You have 60 days from date of issuance of this report to notify us of any material error or omission caused by our negligence, provided, however, that such notice shall be in writing and shall specifically address the issue you wish to raise. A failure to raise such issue within the prescribed time shall constitute your unqualified acceptance of the completeness of this report, the tests conducted and the correctness of the report contents. Unless specific mention, the uncertainty of measurement has been explicitly taken into account to declare the compliance or non-compliance to the specification. The report must not be used by the client to claim product certification, approval, or endorsement by TAF or any government agencies. Report No.: RF200130C10-1 Page No. 2 / 358 Report Format Version: 6.1.1 Table of Contents Release Control Record .................................................................................................................................. 4 1 Certificate of Conformity ...................................................................................................................... 5 2 Summary of Test Results ..................................................................................................................... 6 2.1 Measurement Uncertainty ................................................................................................................... 6 2.2 Modification Record ............................................................................................................................ 6 3 General Information .............................................................................................................................. 7 3.1 General Description of EUT ................................................................................................................ 7 3.2 Description of Test Modes ................................................................................................................... 9 3.2.1 Test Mode Applicability and Tested Channel Detail ............................................................................. 9 3.3 EUT Operating Conditions ................................................................................................................. 11 3.4 Test Setup .......................................................................................................................................... 11 3.5 Duty Cycle of Test Signal .................................................................................................................. 12 3.6 Description of Support Units ............................................................................................................. 15 3.6.1 Configuration of System under Test .................................................................................................. 15 3.6.2 Test Instruments ................................................................................................................................ 16 3.7 General Description of Applied Standards ........................................................................................ 18 4 Test Types and Results ...................................................................................................................... 19 4.1 Modulation characteristics ................................................................................................................. 19 4.1.1 Limits of Modulation characteristics .................................................................................................. 19 4.1.2 Test Instruments ................................................................................................................................ 19 4.1.3 Test Setup .......................................................................................................................................... 19 4.1.4 EUT Operating Conditions ................................................................................................................. 19 4.1.5 Test Results ....................................................................................................................................... 20 4.2 AGC Threshold Level / Mean Output Power and Amplifier/Booster Gain ......................................... 21 4.2.1 Limit of Measuring AGC Threshold Level / Mean Output Power and Amplifier/Booster Gain .......... 21 4.2.2 Test Instruments ...............................................................................................................................…

Text truncated - open the document above for the full version.

Report No.: RF200130C10-1 Page No. 151 / 358 Report Format Version: 6.1.1 Band n261 Test Mode B Frequency Range 1GHz ~18 GHz Channel High Polarity Vertical Beam ID 10(Vertical) Antenna Polarity & Test Distance: Vertical at 3 M No. Freq. (MHz) Reading (dBm) S.G Power Value (dBm) Correction Factor (dB) EIRP (dBm)Limit (dBm) Margin (dB) 1 8208.00 -63.5 -43.2 4.4 -38.8 -13.0 -25.8 2 10792.00 -63.8 -36.6 2.3 -34.3 -13.0 -21.3 3 11285.00 -64.7 -35.8 2.2 -33.6 -13.0 -20.6 4 13240.00 -64.6 -34.5 3.1 -31.4 -13.0 -18.4 5 14311.00 -64.0 -29.5 1.4 -28.1 -13.0 -15.1 6 17813.00 -64.0 -21.5 -2.9 -24.4 -13.0 -11.4 Remarks: 1. EIRP (dBm) = S.G Value (dBm) + Correction Factor (dB). 2. Correction Factor (dB) = Substitution Antenna Gain (dB) + Cable Loss (dB). Report No.: RF200130C10-1 Page No. 152 / 358 Report Format Version: 6.1.1 Band n261 Test Mode B Frequency Range 1GHz ~18 GHz Channel Low Polarity Horizontal Beam ID 10(Horizontal + Vertical) Antenna Polarity & Test Distance: Horizontal at 3 M No. Freq. (MHz) Reading (dBm) S.G Power Value (dBm) Correction Factor (dB) EIRP (dBm)Limit (dBm) Margin (dB) 1 11149.00 -65.2 -36.7 2.2 -34.5 -13.0 -21.5 2 12135.00 -64.7 -37.0 3.8 -33.2 -13.0 -20.2 3 13529.00 -66.0 -33.5 2.6 -30.9 -13.0 -17.9 4 14090.00 -66.4 -33.2 1.6 -31.6 -13.0 -18.6 5 17371.00 -65.9 -30.2 1.1 -29.1 -13.0 -16.1 6 17847.00 -66.3 -25.4 -3.3 -28.7 -13.0 -15.7 Remarks: 1. EIRP (dBm) = S.G Value (dBm) + Correction Factor (dB). 2. Correction Factor (dB) = Substitution Antenna Gain (dB) + Cable Loss (dB). Report No.: RF200130C10-1 Page No. 153 / 358 Report Format Version: 6.1.1 Band n261 Test Mode B Frequency Range 1GHz ~18 GHz Channel Low Polarity Vertical Beam ID 10(Horizontal + Vertical) Antenna Polarity & Test Distance: Vertical at 3 M No. Freq. (MHz) Reading (dBm) S.G Power Value (dBm) Correction Factor (dB) EIRP (dBm)Limit (dBm) Margin (dB) 1 11404.00 -64.3 -37.3 2.4 -34.9 -13.0 -21.9 2 13257.00 -64.9 -34.6 3.0 -31.6 -13.0 -18.6 3 14175.00 -65.9 -31.8 1.6 -30.2 -13.0 -17.2 4 14549.00 -65.9 -32.4 1.5 -30.9 -13.0 -17.9 5 17133.00 -65.1 -30.8 2.0 -28.8 -13.0 -15.8 6 17949.00 -65.2 -20.9 -4.5 -25.4 -13.0 -12.4 Remarks: 1. EIRP (dBm) = S.G Value (dBm) + Correction Factor (dB). 2. Correction Factor (dB) = Substitution Antenna Gain (dB) + Cable Loss (dB). Report No.: RF200130C10-1 Page No. 154 / 358 Report Format Version: 6.1.1 Band n261 Test Mode B Frequency Range 1GHz ~18 GHz Channel Middle Polarity Horizontal Beam ID 10(Horizontal + Vertical) Antenna Polarity & Test Distance: Horizontal at 3 M No. Freq. (MHz) Reading (dBm) S.G Power Value (dBm) Correction Factor (dB) EIRP (dBm)Limit (dBm) Margin (dB) 1 11098.00 -64.5 -36.5 2.2 -34.3 -13.0 -21.3 2 12815.00 -64.0 -35.4 3.8 -31.6 -13.0 -18.6 3 13427.00 -65.8 -33.7 2.8 -30.9 -13.0 -17.9 4 14668.00 -66.0 -33.9 2.1 -31.8 -13.0 -18.8 5 17303.00 -65.7 -30.3 1.5 -28.8 -13.0 -15.8 6 17796.00 -65.9 -25.2 -2.8 -28.0 -13.0 -15.0 Remarks: 1. EIRP (dBm) = S.G Value (dBm) + Correction Factor (dB). 2. Correction Factor (dB) = Substitution Antenna Gain (dB) + Cable Loss (dB). Report No.: RF200130C10-1 Page No. 155 / 358 Report Format Version: 6.1.1 Band n261 Test Mode B Frequency Range 1GHz ~18 GHz Channel Middle Polarity Vertical Beam ID 10(Horizontal + Vertical) Antenna Polarity & Test Distance: Vertical at 3 M No. Freq. (MHz) Reading (dBm) S.G Power Value (dBm) Correction Factor (dB) EIRP (dBm)Limit (dBm) Margin (dB) 1 11268.00 -65.7 -36.9 2.2 -34.7 -13.0 -21.7 2 11744.00 -66.1 -38.2 2.9 -35.3 -13.0 -22.3 3 13750.00 -66.2 -32.9 2.2 -30.7 -13.0 -17.7 4 14345.00 -66.4 -32.0 1.5 -30.5 -13.0 -17.5 5 17473.00 -65.0 -27.9 0.6 -27.3 -13.0 -14.3 6 17796.00 -65.5 -23.1 -2.8 -25.9 -13.0 -12.9 Remarks: 1. EIRP (dBm) = S.G Value (dBm) + Correction Factor (dB). 2. Correction Factor (dB) = Substitution Antenna Gain (dB) + Cable Loss (dB). Report No.: RF200130C10-1 Page No. 156 / 358 Report Format Version: 6.1.1 Band n261 Test Mode B Frequency Range 1GHz ~18 GHz Channel High Polarity Horizontal Beam ID 10(Horizontal + Vertical) Antenna Polarity & Test Distance: Horizontal at 3 M No. Freq. (MHz) Reading (dBm) S.G Power Value (dBm) Correction Factor (dB) EIRP (dBm)Limit (dBm) Margin (dB) 1 10401.00 -65.7 -39.1 2.9 -36.2 -13.0 -23.2 2 11421.00 -65.8 -36.9 2.4 -34.5 -13.0 -21.5 3 13716.00 -65.3 -32.8 2.3 -30.5 -13.0 -17.5 4 14974.00 -65.3 -34.5 3.1 -31.4 -13.0 -18.4 5 17252.00 -66.0 -31.2 1.7 -29.5 -13.0 -16.5 6 17915.00 -65.9 -24.6 -4.1 -28.7 -13.0 -15.7 Remarks: 1. EIRP (dBm) = S.G Value (dBm) + Correction Factor (dB). 2. Correction Factor (dB) = Substitution Antenna Gain (dB) + Cable Loss (dB). Report No.: RF200130C10-1 Page No. 157 / 358 Report Format Version: 6.1.1 Band n261 Test Mode B Frequency Range 1GHz ~18 GHz Channel High Polarity Vertical Beam ID 10(Horizontal + Vertical) Antenna Polarity & Test Distance: Vertical at 3 M No. Freq. (MHz) Reading (dBm) S.G Power Value (dBm) Correction Factor (dB) EIRP (dBm)Limit (dBm) Margin (dB) 1 11234.00 -66.2 -37.4 2.2 -35.2 -13.0 -22.2 2 13563.00 -65.2 -32.9 2.5 -30.4 -13.0 -17.4 3 14345.00 -66.3 -31.9 1.5 -30.4 -13.0 -17.4 4 16929.00 -64.8 -32.3 2.9 -29.4 -13.0 -16.4 5 17592.00 -65.1 -26.8 -0.4 -27.2 -13.0 -14.2 6 18000.00 -66.5 -21.2 -5.1 -26.3 -13.0 -13.3 Remarks: 1. EIRP (dBm) = S.G Value (dBm) + Correction Factor (dB). 2. Correction Factor (dB) = Substitution Antenna Gain (dB) + Cable Loss (dB). Report No.: RF200130C10-1 Page No. 158 / 358 Report Format Version: 6.1.1 Above 18GHz Data (n261): 18GHz-27.475GHz: Mode A Band n261 Beam ID Full Beam / Horizontal Frequency Range 18GHz-27.475GHz Channel Low Antenna polarity Horizontal Test distance 1m Note: The test results already include the correction factor (corrections: On). Report No.: RF200130C10-1 Page No. 159 / 358 Report Format Version: 6.1.1 Band n261 Beam ID Full Beam / Vertical Frequency Range 18GHz-27.475GHz Channel Low Antenna polarity Vertical Test distance 1m Note: The test results already include the correction factor (corrections: On). Report No.: RF200130C10-1 Page …

Text truncated - open the document above for the full version.

Report No.: RF200130C10-1 Page No. 226 / 358 Report Format Version: 6.1.1 Band n261 Beam ID 10 / Horizontal + Vertical Frequency Range 28.375GHz-40GHz Channel Middle Antenna polarity Horizontal Test distance 1m Note: The test results already include the correction factor (corrections: On). Report No.: RF200130C10-1 Page No. 227 / 358 Report Format Version: 6.1.1 Band n261 Beam ID 10 / Horizontal + Vertical Frequency Range 28.375GHz-40GHz Channel Middle Antenna polarity Vertical Test distance 1m Note: The test results already include the correction factor (corrections: On). Report No.: RF200130C10-1 Page No. 228 / 358 Report Format Version: 6.1.1 Band n261 Beam ID 10 / Horizontal + Vertical Frequency Range 28.375GHz-40GHz Channel High Antenna polarity Horizontal Test distance 1m Note: The test results already include the correction factor (corrections: On). Report No.: RF200130C10-1 Page No. 229 / 358 Report Format Version: 6.1.1 Band n261 Beam ID 10 / Horizontal + Vertical Frequency Range 28.375GHz-40GHz Channel High Antenna polarity Vertical Test distance 1m Note: The test results already include the correction factor (corrections: On). Report No.: RF200130C10-1 Page No. 230 / 358 Report Format Version: 6.1.1 40GHz-50GHz (n261): Mode A Band n261 Beam ID Full Beam / Horizontal Frequency Range 40GHz-50GHz Channel Low Antenna polarity Horizontal Test distance 1m Note: The test results already include the correction factor (corrections: On). Report No.: RF200130C10-1 Page No. 231 / 358 Report Format Version: 6.1.1 Band n261 Beam ID Full Beam / Vertical Frequency Range 40GHz-50GHz Channel Low Antenna polarity Vertical Test distance 1m Note: The test results already include the correction factor (corrections: On). Report No.: RF200130C10-1 Page No. 232 / 358 Report Format Version: 6.1.1 Band n261 Beam ID Full Beam / Horizontal Frequency Range 40GHz-50GHz Channel Middle Antenna polarity Horizontal Test distance 1m Note: The test results already include the correction factor (corrections: On). Report No.: RF200130C10-1 Page No. 233 / 358 Report Format Version: 6.1.1 Band n261 Beam ID Full Beam / Vertical Frequency Range 40GHz-50GHz Channel Middle Antenna polarity Vertical Test distance 1m Note: The test results already include the correction factor (corrections: On). Report No.: RF200130C10-1 Page No. 234 / 358 Report Format Version: 6.1.1 Band n261 Beam ID Full Beam / Horizontal Frequency Range 40GHz-50GHz Channel High Antenna polarity Horizontal Test distance 1m Note: The test results already include the correction factor (corrections: On). Report No.: RF200130C10-1 Page No. 235 / 358 Report Format Version: 6.1.1 Band n261 Beam ID Full Beam / Vertical Frequency Range 40GHz-50GHz Channel High Antenna polarity Vertical Test distance 1m Note: The test results already include the correction factor (corrections: On). Report No.: RF200130C10-1 Page No. 236 / 358 Report Format Version: 6.1.1 Band n261 Beam ID Full Beam / Horizontal +Vertical Frequency Range 40GHz-50GHz Channel Low Antenna polarity Horizontal Test distance 1m Note: The test results already include the correction factor (corrections: On). Report No.: RF200130C10-1 Page No. 237 / 358 Report Format Version: 6.1.1 Band n261 Beam ID Full Beam / Horizontal +Vertical Frequency Range …

Text truncated - open the document above for the full version.