NKR-XRCIXRCI NFC Module

NFC module Delivery Specification V0.5 XRCI (PN7150) NFC Module Operation Description (V0.5.1) Model Name: XRCI NFC MODULE Description: NFC reader/writter module compatible Version : V 0.5.1 This document contains proprietary information which is the property of Wistron NeWeb Corporation and is strictly confidential and shall not be disclosed to others in whole or in part, reproduced, copied, or used as basic for design, manufacturing or sale of apparatus without the written permission of Wistron NeWeb Corporation. NFC module Delivery Specification 1 V0.5 1. Introduction PN7150 is a kind of NFC (Near Field Communication) module that could be embedded in one IT system by simply connecting the module through I 2 C interface and start developing his application software. 2. Hardware Block Diagram PN7150 is a full feature NFC module and compliant with NFC standards (NFC Forum, EMVCo, ETSI/SCP). PN7150 has an optimized architecture for low-power consumption in different operation modes. The RF contactless front-end is supporting various transmission modes according to NFCIP- 1, NFCIP-2, ISO/IEC14443, ISO/IEC 15693, ISO-14443, MIFARE, and FeliCa specifications. The major internal components are illustrated in Figure 1-1. Figure 1-1 NFC module Major Component and System Interface NFC module Delivery Specification 2 V0.5 3. Pin Definition ▪ Host connector ▪ Antenna connector Pin number Name Configuration Description 1 MOD_VDD Power Supply Input Module power supply 2 GND Power Supply Ground Module ground 3 n.c. 4 MOD_VUP Power Supply Input Power supply for RF Front-end 5 IRQ Output Interrupt request from module to platform 6 n.c. 7 I 2 C_SDA Input/ Output I 2 C data 8 I 2 C_SCL Input I 2 C clock 9 GND Input Used for extra GND for signal integrity 10 RESET Input Reset pin input from the host to wake up the device from standby and also to reset the device 11 n.c. 12 n.c. 13 MOD_VDD Power supply input Additional pin for module power supply to support higher current capacity 14 VDD_IO Power supply input Host IO reference voltage 15 GND Power Supply Ground Module ground Pin number Name Configuration Description 1 n.c. 2 RXN Input Antenna reception path #2 3 TX2 Output Antenna transmission line #2 4 GND Ground Antenna ground 5 TX1 Output Antenna transmission line #1 6 RXP Input Antenna reception path #1 7 n.c. NFC module Delivery Specification 3 V0.5 4. Specification Item Standard specifications Main chipset  NXP PN7150 Frequency  13.56MHz NFC Standards  ISO/IEC 14443A, ISO/IEC 14443B PCD mode  FeliCa PCD mode  MIFARE PCD encryption mechanism (MIFARE Classic 1K/4K)  ISO/IEC 15693/ICODE VCD mode  NFC Forum tags 1 to 5  NFCIP-1/NFCIP-2 protocol Host interface  NCI protocol interface according to NFC Forum standardization  I 2 C High-speed mode supported I 2 C Address  0x28 Host connector  15 Pin FPC/FFC Antenna connector  7 Pin FPC/FFC Ambient temperature  -25 ~ 80 o C (Typical: 25 o C) Storage temperature  -25 o ~ 125 o C Weight  TBD 5. Electrical Characteristics Recommended Operating conditions Symbol Parameter Min Typical Maximum Unit MOD_VDD Power supply input 2.7 3.3 5.5 V MOD_VUP Power supply input 2.7 3.3 5.5 VDD_IO IO power supply 1.65 1.8 1.95 3.0 3.3 3.6 Current consumption characteristics Symbol Min Typical Maximum Unit I MOD_VDD -- -- 190 [1] mA I VDD_IO -- -- 15 [1] MOD_VDD=3.3V NFC module Delivery Specification 4 V0.5 6. Power Consumption (TBD) Test condition: MOD_VDD = 3.3V, VDD_IO= 3.3V, MOD_VUP =5V (continuously TX mode) 6.1 Test conditions PCB P/N Hardware version Firmware version Antenna Impedance Transfer Board Consumption (mA) @ 5V 6.2 Power Consumption 3.3V Power Rail Current (mA), RF TxLDO=3.3V (MOD_VDD + VDD_IO + VDD_SIM) *1 Standby (RF OFF, VEN Pull Low) AVG Peak Polling Mode *2 AVG Peak Detected Test Tag type Type 1 Topaz Type 2 Mifare Type 3 Felica Type 4 Mifare Desfire Communicating AVG Peak *1: Means NFC module “Digital part” power consumption *2: Means “Normal” polling mode. 3.3V Power Rail Current (mA), RF TxLDO =4.7V (MOD_VDD + VDD_IO + VDD_SIM) Standby (RF OFF, VEN Pull Low) AVG Peak Polling Mode AVG Peak Detected Test Tag type Type 1 Topaz Type 2 Mifare Type 3 Felica Type 4 Mifare Desfire Communicating AVG Peak NFC module Delivery Specification 5 V0.5 5V Power Rail Current (mA), RF TxLDO=3.3V (MOD_VUP) *3 Standby (RF OFF, VEN Pull Low) AVG Peak Polling Mode AVG Peak Detected Test Tag type Type 1 Topaz Type 2 Mifare Type 3 Felica Type 4 Mifare Desfire Communicating AVG Peak *3: Means NFC module “RF part” power consumption 5V Power Rail Current (mA), RF TxLDO=4.7V (MOD_VUP) Standby (RF OFF, VEN Pull Low) AVG Peak Polling Mode AVG Peak Detected Test Tag type Type 1 Topaz Type 2 Mifare Type 3 Felica Type 4 Mifare Desfire Communicating AVG Peak NFC module Delivery Specification 6 V0.5 7. Recommended Operation Temperature Supply voltage  AC mains  DC Type of DC Source  Internal DC supply  External DC adapter  Battery Operational Climatic  Tnom (25 °C)  Tmax (80 °C)  Tmin (-25 °C) NFC module Delivery Specification 7 V0.5 8. Power Sequence 8.1 Power up Symbol Parameter Min Typical Max Unit t t(MOD_VDD - MOD_VUP) Minimum time from VDD_MOD high to MOD_VUP high 0 0.5 ms t t(MOD_VDD - VDD_IO) Minimum time from VDD_MOD high to VDD_IO high 0 0.5 ms t t(VDD_IO - Reset) Minimum time from VDD_IO high to Reset high 0 0.5 ms NFC module Delivery Specification 8 V0.5 8.2 Reset (via RESET pin) Symbol Parameter Conditions Min Typical Max Unit t W(RESET) RESET pulse width to reset 10 - - μs t boot Boot time - - 2.5 ms NFC module Delivery Specification 9 V0.5 8.3 Power down NFC module Delivery Specification 10 V0.5 9. Mechanical Dimension NFC module Delivery Specification 11 V0.5 10. FPC/FFC Specifications 10.1 15 pin FFC ▪Connector Vendor: CVILUX ▪Connector Vendor P/N: CF39152D0R0-NH 10.2 7 pin FPC/FFC ▪Connector Vendor: CVILUX ▪Connector Vendor P/N: CF4207FH0R0-05-NH NFC module Delivery Specification 12 V0.5 11. Antenna Reference Matching Circuit Reference impedance ran…

Text truncated - open the document above for the full version.

FCC ID: NKR-XRCI Modular Approval Request Letter Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch June 12, 2020 Dear Application Examiner, Wistron NeWeb Corp., XRCI NFC Module, FCC ID: NKR-XRCI would like to have your authorization as a modular approval specific to the mobile RF exposure condition. The requirements of KDB996369 have been met and shown on the following statements. 1. “The modular transmitter must have its own RF shielding.” The radio portion of this module has been shielded, please see exhibition External Photo. 2. “The modular transmitter must have buffered modulation/data inputs.” The EUT has buffered data inputs, it is integrated in chip PN7150. 3. “The modular transmitter must have its own power supply regulation.” The part number of this regulator is PN7150. 4. “The modular transmitter must comply with the antenna requirements of section 15.203 and 15.204(C).” The EUT meets the FCC antenna requirements. The spurious emission, unique antenna connector and photo of antennas are shown in the test report. 5. “The modular transmitter must be tested in a stand-alone configuration” The EUT was tested in a stand-alone configuration via a USB extender. Please see section Photographs of Test Configuration in the test report, the EUT was plugged in this extender. 6. “The modular transmitter must be labeled with its own FCC ID number.” Please see exhibition Label Sample for the FCC ID of this module. And also in the exhibition Users Manual, there are instructions give to the OEM on how to label the end product. FCC ID: NKR-XRCI 7. “The modular transmitter must comply with any specific rule or operating requirements applicable to the transmitter and the manufacturer must provide adequate instructions along with the module to explain any such requirements.” The EUT is compliant with all applicable FCC rules. Detail instructions for maintaining compliance are given in the Users Manual. 8. “The modular transmitter must comply with any applicable RF exposure requirements.” The EUT is compliant with all applicable RF exposure requirements. Due to the low power nature, RF exposure is exempted. Please contact me if you have any further questions. Thanks for your attention. Best Regards, Debby Lin, Senior Specialist Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch

Reference No.:200603E01-1 Page 1/5 CONSTRUCTION PHOTOS OF EUT EUT + Antenna EUT Reference No.:200603E01-1 Page 2/5 Reference No.:200603E01-1 Page 3/5 Reference No.:200603E01-1 Page 4/5 Antenna Reference No.:200603E01-1 Page 5/5

Label Location Back of EUT Brand name：WNC Model name：XRCI FCC ID：NKR-XRCI

Reference No.:200603E01-2 Page 1/2 CONSTRUCTION PHOTOS OF EUT Reference No.:200603E01-2 Page 2/2

Report No.: RF200507E01A Page No. 1 / 64 Report Format Version: 6.1.1 Reference No.: 200603E01 FCC Test Report (NFC) Report No.: RF200507E01A FCC ID: NKR-XRCI Test Model: XRCI Received Date: May 03, 2020 Test Date: May 04 to 18, 2020 Issued Date: June 09, 2020 Applicant: Wistron NeWeb Corp. Address: 20 Park Avenue II, Hsinchu Science Park,Hsinchu 308, Taiwan, R.O.C. Issued By: Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch Hsin Chu Laboratory Lab Address: E-2, No.1, Li Hsin 1st Road, Hsinchu Science Park, Hsinchu City 300, Ta i w a n Test Location: E-2, No.1, Li Hsin 1st Road, Hsinchu Science Park, Hsinchu City 300, Ta i w a n FCC Registration / Designation Number: 723255 / TW2022 This report is for your exclusive use. Any copying or replication of this report to or for any other person or entity, or use of our name or trademark, is permitted only with our prior written permission. This report sets forth our findings solely with respect to the test samples identified herein. The results set forth in this report are not indicative or representative of the quality or characteristics of the lot from which a test sample was taken or any similar or identical product unless specifically and expressly noted. Our report includes all of the tests requested by you and the results thereof based upon the information that you provided to us. You have 60 days from date of issuance of this report to notify us of any material error or omission caused by our negligence, provided, however, that such notice shall be in writing and shall specifically address the issue you wish to raise. A failure to raise such issue within the prescribed time shall constitute your unqualified acceptance of the completeness of this report, the tests conducted and the correctness of the report contents. Unless specific mention, the uncertainty of measurement has been explicitly taken into account to declare the compliance or non-compliance to the specification. The report must not be used by the client to claim product certification, approval, or endorsement by TAF or any government agencies. Report No.: RF200507E01A Page No. 2 / 64 Report Format Version: 6.1.1 Reference No.: 200603E01 Table of Contents Release Control Record .................................................................................................................................. 3 1 Certificate of Conformity ...................................................................................................................... 4 2 Summary of Test Results ..................................................................................................................... 5 2.1 Measurement Uncertainty ................................................................................................................... 5 2.2 Modification Record ............................................................................................................................ 5 3 General Information .............................................................................................................................. 6 3.1 General Description of EUT ................................................................................................................ 6 3.2 Description of Test Modes ................................................................................................................... 7 3.2.1 Test Mode Applicability and Tested Channel Detail ............................................................................. 8 3.3 Description of Support Units ............................................................................................................. 10 3.3.1 Configuration of System under Test .................................................................................................. 10 3.4 General Description of Applied Standards ......................................................................................... 11 4 Test Types and Results ...................................................................................................................... 12 4.1 Radiated Emission Measurement ..................................................................................................... 12 4.1.1 Limits of Radiated Emission Measurement ....................................................................................... 12 4.1.2 Test Instruments ................................................................................................................................ 13 4.1.3 Test Procedures ................................................................................................................................. 14 4.1.4 Deviation from Test Standard ............................................................................................................ 14 4.1.5 Test Setup .......................................................................................................................................... 15 4.1.6 EUT Operating Conditions ................................................................................................................. 15 4.1.7 Test Results ....................................................................................................................................... 16 4.2 Conducted Emission Measurement .................................................................................................. 49 4.2.1 Limits of Conducted Emission Measurement .................................................................................... 49 4.2.2 Test Instruments ................................................................................................................................ 49 4.2.3 Test Procedures ................................................................................................................................. 50 4.2.4 Deviation from Test Standard .......................................................…

Text truncated - open the document above for the full version.

Reference No.: 200603E01 Page No. 1 / 3 Report No.: RT200507E01 PHOTOGRAPHS OF THE TEST CONFIGURATION CONDUCTED EMISSION TEST Reference No.: 200603E01 Page No. 2 / 3 Report No.: RT200507E01 RADIATED EMISSION TEST (Below 1GHz) Reference No.: 200603E01 Page No. 3 / 3 Report No.: RT200507E01