NKRKU8M802.11b WLAN USB Adapter

802.11b WLAN USB Adapter with 128MB Flash Disk Model KU8-M User’s Guide Version: 1.0 — Sept. 2003 1 Copyright Statement No part of this publication may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, whether electronic, mechanical, photocopying, recording or otherwise without the prior writing of the publisher. Windows ™ 98SE/2000/ME/XP/CE are trademarks of Microsoft ® Corp. Pentium is trademark of Intel. All copyright reserved. 2 Regulatory Information Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures: - Reorient or relocate the receiving antenna. - Increase the separation between the equipment and receiver. - Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. - Consult the dealer or an experienced radio/TV technician for help. FCC Caution: To assure continued compliance, (example - use only shielded interface cables when connecting to computer or peripheral devices) any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. IMPORTANT NOTE: FCC Radiation Exposure Statement: This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. 3 Table of Contents REGULATORY INFORMATION 2 1. WELCOME 5 1.1 KIT CONTENTS 6 1.2 PRODUCT FEATURES 7 1.3 WIRELESS NETWORKING SCENARIOS 9 1.4 ADVANTAGES FOR USING WIRELESS NETWORK 11 2. AS FLASH DISK 12 2.1 INSTALLATION 12 2.2 UNPLUG THE USB ADAPTER 14 3. AS WIRELESS NETWORKING 15 3.1 INSTALL THE IEEE802.11B WLAN DRIVER / UTILITY 16 3.1.1 ADDITIONAL SETUP PROCESSES 19 3.1.2 DISABLE WINDOWS XP ZERO-CONFIGURATION 20 3.2 VERIFYING THE DRIVER/UTILITY 21 3.3 IEEE802.11B WLAN UTILITY 22 3.4 BASIC SETTING FOR INFRASTRUCTURE MODE 23 3.5 BASIC SETTING FOR 802.11AD HOC MODE/AD HOC MODE 24 3.6 ADVANCED SETTINGS 25 3.7 ENCRYPTION FUNCTION 26 3.8 UNINSTALL THE IEEE802.11B WLAN UTILITY / DRIVER 29 4. USING THE UTILITY 30 4.1 LAN STATUS TAB 30 4.2 LINK INFORMATION TAB 31 4.3 SITE SURVEY TAB 31 4.4 DIAGNOSTIC TAB 32 4.5 ABOUT TAB 32 4 5. NETWORK APPLICATION 33 5.1 SURVEYING THE NETWORK NEIGHBORHOOD 33 5.2 FILE SHARING 34 5.3 USING THE SHARED FOLDER 35 6. PRODUCT SPECIFICATIONS 36 5 1. Welcome Thank you for purchasing our 802.11b WLAN USB Adapter with 128MB Flash Disk, and welcome to Wireless LAN—the easy way to wireless networking. This user’s guide introduces to you the 802.11b WLAN USB Adapter with 128MB Flash Disk and describes the most common configurations, which will help you connect to your network easily. Please read this manual to get familiar with the IEEE802.11b Wireless LAN. This manual contains detailed instructions in operation of this product. Please keep this manual for future reference. As this product is designed to run under Microsoft Windows, it is recommended that to be installed by people who are familiar with the installation procedures for network operating systems under Microsoft Windows. 6 1.1 Kit Contents The 802.11b WLAN USB Adapter with 128MB Flash Disk kit should include the following items: One 802.11b WLAN USB Adapter with 128MB Flash Disk, one CD and one Quick Start Guide. a. One 802.11b WLAN USB Adapter with 128MB Flash Disk b. One Software CD including: 1. Driver for support Windows 98SE 2. User Manual PDF File c. Quick Start Guide If any of the items mentioned above are damaged or missing, please contact your distributor. 7 1.2 Product Features A. Status LED LED1 (Blue) LED2 (Green) Off Power Off. Power off or in Standby / Power saving Blinking The USB adapter is Powered on and searching for AP before connecting The memory disk is in Read / Write processing (busy state) Steady Blue Wireless connection is linked. N/A B. USB Connector C. Switch l On: The radio (wireless function) is on. l Off: The radio (wireless function) is off. A B C 8 802.11b WLAN USB Adapter with 128MB Flash Disk features: 1. High-speed wireless connection, up to 11 Mbps 2. IEEE802.11b (DSSS) standard for 2.4 GHz Wireless LAN 3. Plug-and-Play 4. Solid design with an integrated antenna 5. Full mobility and seamless cell-to-cell roaming 6. Automatic scale back at per packet level 7. Dual mode Application (Memory & WLAN) 8. Pen Driver mode only (radio off) 9. Radio ON/Off Switch 10. Supports security & Boot up function 802.11b WLAN USB Adapter with 128MB Flash Disk supports: 1. Automatic load balancing for optimized bandwidth 2. Advanced power management 3. No driver required for Windows 2000 / ME / XP 4. Support Windows 98 / 98SE with device driver 9 1.3 Wireless Networking Scenarios As our 802.11b WLAN USB Adapter with 128MB Flash Disk is interoperable and compatible with other IEEE 802.11b compliant products from other manufacturers, it offers you the most freedom to establish your ideal wireless network. Therefore, after installing 802.11b WLAN USB Adapter with 128MB Flash Disk, you can connect your …

Text truncated - open the document above for the full version.

Wistron Neweb Corporation No. 10-1, Li-hsin Road 1, Science-based Industrial Park,Hsinchu 300, Taiwan, R. O. C. 886-3-666-7799 886-3-666-1654 Rev 2 C:\tmp\03LR019 Ku8-m\fcc\AP FORM.doc 02/08/02 Letter Of Agency Date: Oct. 09, 2003 American Telecommunications Certification Body, Inc. 6731 Whittier Avenue Suite C110 McLean, VA 22101 To Whom It May Concern: Please be advised that Wistron NeWeb Corporation authorizes International Standards Laboratory (ISL) to act on our behalf, until otherwise notified, for applications submitted to American Telecommunications Certification Body, Inc. (ATCB). We certify that we are not subject to denial of federal benefits that includes FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse ACT of 1988, U.S.C. 862. Further, no party as defined in 47 CFR 1.2002(b), for this application is subject to denial of federal benefits that includes FCC benefits. Thank you for your attention to this matter. ________________ Eric Liu / Sr. Manager Engineer Wistron NeWeb Corporation Wistron Neweb Corporation No. 10-1, Li-hsin Road 1, Science-based Industrial Park,Hsinchu 300, Taiwan, R. O. C. 886-3-666-7799 886-3-666-1654 Rev 2 C:\tmp\03LR019 Ku8-m\fcc\AP FORM.doc 02/08/02 FCC Labeling Requirements and Information Date: Oct. 9, 2003 American Telecommunications Certification Body, Inc. 6731 Whittier Avenue Suite C110 McLean, VA 22101 RE: FCC Labeling Requirements FCC ID: NKRKU8M The following label information is required by the FCC Rules and Regulations for certified devices. Please find marketing information required by the FCC Rules and Regulations as following: Label Requirements An intentional radiator device subject to certification by the FCC shall carry a warning label which includes the following statement: (Due to space limitation, this statement will be shown on Users’ Manual Page 2.) This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. The sample label shown shall be permanently affixed at a conspicuous location on the device and be readily visible to the user at the time of purchase. FCC ID: NKRKU8M Thank you for your attention to these matters. Sincerely, ________________ Eric Liu / Sr. Manager Engineer Wistron NeWeb Corporation Wistron Neweb Corporation No. 10-1, Li-hsin Road 1, Science-based Industrial Park,Hsinchu 300, Taiwan, R. O. C. 886-3-666-7799 886-3-666-1654 Rev 2 C:\tmp\03LR019 Ku8-m\fcc\AP FORM.doc 02/08/02 Request for Confidentiality Date: Oct. 9, 2003 American Telecommunications Certification Body, Inc. 6731 Whittier Avenue Suite C110 McLean, VA 22101 RE: Certification Application FCC ID: NKRKU8M Please be advised that the following information is to be held confidential on behalf of Wistron NeWeb Corporation : q Block Diagram q Schematics q Technical Spec The application contains technical information which Wistron NeWeb Corporation deems to be trade secrets and proprietary. If made public, the information might be used to the disadvantage of the applicant in the market place. Thank you for your attention to this matter. Sincerely, ________________ Eric Liu / Sr. Manager Engineer Wistron NeWeb Corporation

American Telecommunications Certification Body Inc. 6731 Whittier Ave, McLean, VA 22101 ` October 22, 2003 RE: Wistron Neweb Corporation FCC ID: NKRKU8M After a review of the submitted information, I have a few comments on the above referenced Application. General 1) This device is also subject to a DoC as given by the type of device an labeling. However the users manual must also contain the Statement of Compliance information given below on the SAME page (i.e. page 2) as the 2 part FCC statement. Please provide an updated users manual. COMPLIANCE INFORMATION (47CFR 2.1077) If a product is tested and authorized under a Declaration of Conformity, a compliance information statement shall be supplied with the product at the time of marketing or importation, containing the following information on a single page: (1) Identification of the product, i.e. name and model number. (2) A statement similar to that contained in Section 15.19(a)(3) that the product complies with Part 15 of the regulations. - NOTE THIS IS ALREADY SHOWN ON PAGE 2 OF THE USERS MANUAL. (3) The identification, by name, address and telephone number, of the responsible party. The responsible party is defined as either the manufacturer, or if the equipment is imported, the importer. The responsible party for a Declaration of Conformity must be located within the United States. Timothy R. Johnson Examining Engineer mailto: [email protected] The items indicated above must be submitted before processing can continue on the above referenced application. Failure to provide the requested information may result in application termination. Correspondence should be considered part of the permanent submission and may be viewed from the Internet after a Grant of Equipment Authorization is issued. Please do not respond to this correspondence using the email reply button. In order for your response to be processed expeditiously, you must submit your documents through the AmericanTCB.com website. Also, please note that partial responses increase processing time and should not be submitted. Any questions about the content of this correspondence should be directed to the sender.

KU8-M XXX XX XXXXXXXX XXX XX XXXXXXXX XXXXXXXX Label Location Label Location

International Standards Laboratory Report Number: ISL-03LR019P NVLAP Lab. Code: 200234-0; VCCI: R-1435, C-1440; NEMKO Aut. No: ELA 113b, 193b; BSMI Lab. Code: SL2-IN-E-0013 Appendix Photographs of EUT of WLAN b USB Adapter with Flash Disk Model: KU8-M (Brand:Wistron NeWeb) International Standards Laboratory Report Number: ISL-03LR019P NVLAP Lab. Code: 200234-0; VCCI: R-1435, C-1440; NEMKO Aut. No: ELA 113b, 193b; BSMI Lab. Code: SL2-IN-E-0013 -1- EUT-1 International Standards Laboratory Report Number: ISL-03LR019P NVLAP Lab. Code: 200234-0; VCCI: R-1435, C-1440; NEMKO Aut. No: ELA 113b, 193b; BSMI Lab. Code: SL2-IN-E-0013 -2- EUT-2 International Standards Laboratory Report Number: ISL-03LR019P NVLAP Lab. Code: 200234-0; VCCI: R-1435, C-1440; NEMKO Aut. No: ELA 113b, 193b; BSMI Lab. Code: SL2-IN-E-0013 -3- EUT-3 International Standards Laboratory Report Number: ISL-03LR019P NVLAP Lab. Code: 200234-0; VCCI: R-1435, C-1440; NEMKO Aut. No: ELA 113b, 193b; BSMI Lab. Code: SL2-IN-E-0013 -4- EUT-4 International Standards Laboratory Report Number: ISL-03LR019P NVLAP Lab. Code: 200234-0; VCCI: R-1435, C-1440; NEMKO Aut. No: ELA 113b, 193b; BSMI Lab. Code: SL2-IN-E-0013 -5- EUT-5

Report Number: 03LR018FC Test Date: 2003/09/29 NVLAP Lab. Code: 200234-0; VCCI: R-1435, C-1440; NEMKO Aut. No: ELA 113; BSMI Lab. Code: SL2-IN-E-0013 Test Report FOR FCC Part 15 Subpart C of WLAN b USB Adapter with Flash Disk Model: KU8-M (Brand:Wistron NeWeb) Applied by: Wistron NeWeb Corporation No. 10-1, Li-hsin Road I, Science-based Industrial Park Hsinchu 300, Taiwan, R. O. C. : (NVLAP Lab. Code: 200234-0) Test Performed by International Standards Laboratory No. 120, Lane 180, San Ho Tsuen, Hsin Ho Rd. Lung-Tan Hsiang, Tao Yuan County 325 Taiwan, R.O.C. Tel:(03)407-1718 Fax:(03)407-1738 FCC ID: NKRKU8M International Standards Laboratory Report Number: NVLAP Lab. Code: 200234-0; VCCI: R-1435, C-1440; NEMKO Aut. No: ELA 113; BSMI Lab. Code: SL2-IN-E-0013 -i- Contents of Report 1. . General...............................................................................................1 1.1 Certification of Accuracy of Test Data.............................................................................1 1.2 Test Results Summary.....................................................................................................2 1.3 Description of Equipment Under Test (EUT)...................................................................3 1.4 Test Standards and Procedure........................................................................................4 1.5 General Test Conditions..................................................................................................4 2. Powerline Conducted Emissions [Section 15.207]....................................5 2.1 EUT Configuration..........................................................................................................5 2.2 Test Procedure...............................................................................................................5 2.3 EMI Receiver/Spectrum Analyzer Configuration (for the frequencies tested).....................5 2.4 Test Data:.......................................................................................................................6 3. Bandwidth for DSSS [Section 15.247 (a)(2)]............................................8 3.1 Test Procedure...............................................................................................................8 3.2 Test Setup......................................................................................................................8 3.3 Test Data........................................................................................................................8 4. DSSS Maximum Peak Output Power [Section 15.247 (b)(1)]..................11 4.1 Test Procedure.............................................................................................................11 4.2 Test Setup....................................................................................................................11 4.3 Test Data:.....................................................................................................................11 5. Radiated Emission Measurement [Section [15.247(c)(4)]........................12 5.1 EUT Configuration........................................................................................................12 5.2 Test Procedure.............................................................................................................12 5.3 EMI Receiver/Spectrum Analyzer Configuration (for the frequencies tested)...................12 5.4 Test Data (30MHz – 1GHz) :........................................................................................13 5.5 Test Data ( 1GHz – 25 GHz, Transmitting from Main antenna) ......................................14 6. Band Edge Measurement.......................................................................17 6.1 Test Procedure (Conducted).........................................................................................17 6.2 Test Setup (Conducted)................................................................................................17 6.3 Test Data:.....................................................................................................................17 6.4 Band Edge measurement Test Procedure (Radiated)......................................................20 6.5 Test Setup (Radiated)...................................................................................................20 6.6 Test Data:.....................................................................................................................21 7. RF Exposure Measurement [Section 15.247(b)(4) & 1.1307(b)]..............26 7.1 Applied Standards........................................................................................................26 7.2 Calculation for Maximum Permissible Exposure (MPE)..................................................26 8. DSSS Peak Power Spectral Density [Section 15.247(d) ]........................27 8.1 Test Procedure.............................................................................................................27 8.2 Test Setup....................................................................................................................27 8.3 Test Data:.....................................................................................................................27 9. Appendix............................................................................................31 9.1 Appendix A: Measurement Procedure for Power-line Conducted Emissions...................31 9.2 Appendix B: Test Procedure for Radiated Emissions......................................................32 9.3 Appendix C: Test Equipment.........................................................................................33 FCC ID: NKRKU8M International Standards Laboratory Report Number: NVLAP Lab. Code: 200234-0; VCCI: R-1435, C-1440; NEMKO Aut. No: ELA 113; BSMI Lab. Code: SL2-IN-E-0013 -ii- 9.3.1 Test Equipment List....…

Text truncated - open the document above for the full version.

The Front View of Highest Conducted Set-up For EUT The Front View of Highest Radiated Set-up For EUT The Back View of Highest Radiated Set-up For EUT