NTMAT-200IDAudio Guide using 125kHz RFID technology

AT-200iD-MT Audio Guide User Manual Most users do not need a license to operate this wireless microphone system. Nevertheless, operating this microphone system without a license is subject to certain restrictions: The system may not cause harmful interference; it must operate at a low power level (not in excess of 50 milliwatts); and it has no protection from interference received from any other device. Purchasers should also be aware that the FCC is currently evaluating use of wireless microphone systems, and these rules are subject to change. For more information, call the FCC at 1–888–CALL–FCC (TTY: 1–888–TELL–FCC) or visit the FCC’s wireless microphone Web ments and void user’s authority to operate the device. Consumer Alert site at http://www.fcc.gov/cgb/wirelessmicrophones. Notice: The changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. IMPORTANT NOTE: To comply with the FCC RF exposure compliance requirements, no change to the antenna or the device is permitted. Any change to the antenna or the device could result in the device exceeding the RF exposure require- If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: —Reorient or relocate the receiving antenna. —Increase the separation between the equipment and receiver. —Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. —Consult the dealer or an experienced radio/ TV technician for help. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.However, there is no guarantee that interference will not occur in a particular installation. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. Notice: The changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Preface Thank you for the purchase of Audio Guide AT-200. This user manual contains comprehensive instructions and operation of the unit, please read it over before your use for the first time. Features High fidelity DSP technology, offering up to 20 hours stereo audio playback with built-in 2GB memory card. Access audio content through built-in speaker or external earphone jacks. 2 earphone jacks available for couple or kids and parents. Backlit display and keypad for ease of use. Raised dot 5 for visual impaired people. Chargeable. Audio Guide can be recharged with chargers. Each charge can run operation up to 12 hours. Fast audio content update through Audio Master and Audio Guide Uploader. AT-200 Audio Guide Earphone jack Triggering module Charging indicator Inbuilt speaker OLED screen Keypad Power/Stop button Uploading/Charging connector Battery door Illustration 1. Earphone jack, stereo, 3.5 mm 1 or 2 headphones are valid for more than 1 user. 2. Triggering module In addition to inbuilt IR triggering mode, various triggering options (RFID/RF/ GPS) are offered respectively upon demands. 3. Charging indicator Glittery red LED indicator means potentially defective battery inside. Please hand over the audio guide to the counter. Red/Green LED indicator stands for charging/fully charged status. AT-200 Audio Guide 7. Power/Stop button 4. Inbuilt speaker Users can listen to audio commentaries through the inbuilt speaker. However, this function will be disabled when the player connects with headphones. 5. OLED screen Triggering modes, battery status, volumes, photos of exhibits, and playing tracks/progress will display on the OLED screen. 6. Keypad Numeric buttons for audio tracks Fast forward, next track Fast backward, last track Play & Pause Volume up Volume down NOTE: 2 auxiliary buttons, and , are designed for further information and will be updated by organizers. To power on - press power button for about 1 second. To power off - press power button for about 2 seconds till “OFF” shows up. To stop or redial codes of an audio commentary, simply press stop button and dial new codes again. 9. Battery door If the inbuilt battery is failed, open the battery door for replacement. 8. Uploading/Charging connector (IEEE 1394 port) This port will be connected with uploaders/chargers for either uploading or recharging. AT-200 Audio Guide Operation Power ON/OFF Press and hold power button for 1 second until a beep to power on. Press and hold the button for 2 seconds until an OFF sign shown in display and beeps twice to power off. (* Alarm is still working even audio guide is off.) Auto Power OFF When audio guide is not operated for 30 minutes (factory default), it will switch off automatically. (* Alarm is still working.) Auto Power Off can be changed or defined through software “Audio Master G2”. Automatic audio play is only working with specific devices : IT-200, RT-200, iD-200, which are optional on demand. Choose Language Change and choose a desired language by entering 3 number codes with # and press to activate. A prompt audio and display will give assistive information to your change when the change is successful. (Language code is available from 951 to 982. 951 is the factory default.) Manual Play and Auto Play There are two ways to activate a picked aud…

Text truncated - open the document above for the full version.

910805 1 OKAYO Electronics Co., Ltd. No.2, Gongye 10 th Rd., Dali Dist., Taichung 41280, Taiwan Date: Sep. 12, 2013 Compliance Certification Services Certification Division 47173 Benicia Street Fremont, CA 94538, USA To whom it may concern: We, the undersigned, hereby authorize ELECTRONICS TESTING CENTER, TAIWAN, to act on our behalf in all manners relating to application for equipment authorization, including signing of all documents relating to these matters. Any and all acts carried out by ELECTRONICS TESTING CENTER, TAIWAN on our behalf shall have the same effect as acts of our own. We, the undersigned, hereby certify that we are not subject to a denial of federal benefits, that includes FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C. 853(a). In authorizing ELECTRONICS TESTING CENTER, TAIWAN as our agent, we still recognize that we are responsible to: a) comply with the relevant provisions of the certification program; b) make all necessary arrangements for the conduct of the evaluation, including provision for examining documentation and access to all areas, records (including internal audit reports) and personnel for the purposes of evaluation (e.g. testing, inspection, assessment, surveillance, reassessment) and resolution of complaints; c) make claims regarding certification only in respect of the scope for which certification has been granted; d) do not use our product certification in such a manner as to bring the Certification Division into disrepute and not make any statement regarding our product certification which the Certification Division may consider misleading or unauthorized; e) upon suspension or cancellation of certification, discontinue use of all advertising matter that contains any reference thereto and return any certification documents as required by the Certification Division; f) use certification only to indicate the products are certified as being in conformity with specified standards; 910805 2 g) endeavor to ensure that no certificate or report nor any part thereof is used in a misleading manner; h) ensure that any reference to our product certification in communication media such as documents, brochures or advertising, complies with the requirements of the Certification Division; i) keep a record of all complaints made known to the us relating to the product’s compliance with requirements of the relevant standard and to make these records available to the Certification Division when requested; j) take appropriate action with respect to such complaints and any deficiencies found in products or services that affect compliance with the requirements for certification; k) document the actions taken. This authorization is valid until further written notice from the applicant. Sincerely Yours, (signature) Stephen Wei / Sales Manager OKAYO Electronics Co., Ltd. No.2, Gongye 10 th Rd., Dali Dist., Taichung 41280, Taiwan

910805 1 OKAYO Electronics Co., Ltd. No.2, Gongye 10 th Rd., Dali Dist., Taichung 41280, Taiwan Federal Communications Commission FCC ID: NTMAT-200ID Product Name: Audio Guide Model Name: AT-200iD-MT Trade Name: OKAYO Dear Sir: In accordance with 47 C.F.R. Section 0457 and 0.459, we would like to request confidentiality on some exhibits we submitted for above application for the reason of trade secret. If those exhibits are available for public inspection, any person who once gets the information contained in those exhibits will be able to design and to make the same products very easily. This is a very serious problem and huge loss for us, because we did invest so much on it. Please be not made the Exhibit Types listed below routinely available for public inspection: Block Diagram and Schematics and Operation Description. By: By: Stephen Wei (Signature) (Printed) Title : Sales Manager Applicant : OKAYO Electronics Co., Ltd. Address : No.2, Gongye 10 th Rd., Dali Dist., Taichung 41280, Taiwan Tel : 886-4-24914666 Fax: 886-4-24913066 Date : Sep. 12, 2013

ETC Report No. : 13-05-RBF-025-01 Sheet 1 of 8 Sheets FCC ID. : NTMAT-200ID Rev. No 2.0 CONSTRUCTION PHOTOS OF EUT 1. 2. ETC Report No. : 13-05-RBF-025-01 Sheet 2 of 8 Sheets FCC ID. : NTMAT-200ID Rev. No 2.0 CONSTRUCTION PHOTOS OF EUT 3. 4. ETC Report No. : 13-05-RBF-025-01 Sheet 3 of 8 Sheets FCC ID. : NTMAT-200ID Rev. No 2.0 CONSTRUCTION PHOTOS OF EUT 5. 6.

AT-200iD-MT

ETC Report No. : 13-05-RBF-025-01 Sheet 4 of 8 Sheets FCC ID. : NTMAT-200ID Rev. No 2.0 CONSTRUCTION PHOTOS OF EUT 7. 8. ETC Report No. : 13-05-RBF-025-01 Sheet 5 of 8 Sheets FCC ID. : NTMAT-200ID Rev. No 2.0 CONSTRUCTION PHOTOS OF EUT 9. 10. ETC Report No. : 13-05-RBF-025-01 Sheet 6 of 8 Sheets FCC ID. : NTMAT-200ID Rev. No 2.0 CONSTRUCTION PHOTOS OF EUT 11. ETC Report No. : 13-05-RBF-025-01 Sheet 7 of 8 Sheets FCC ID. : NTMAT-200ID Rev. No 2.0 CONSTRUCTION PHOTOS OF EUT 12. 13. ETC Report No. : 13-05-RBF-025-01 Sheet 8 of 8 Sheets FCC ID. : NTMAT-200ID Rev. No 2.0 CONSTRUCTION PHOTOS OF EUT 14. 15.

Rev. No 2.0 FCC Part 15 EMI TEST REPORT of E.U.T. : Audio Guide Model : AT-200iD-MT; AT-200iD FCC ID : NTMAT-200ID for APPLICANT : OKAYO ELECTRONICS CO., LTD. ADDRESS : No.2, Gongye 10 th Rd., Dali Dist., Taichung 41280, Taiwan Test Performed by ELECTRONICS TESTING CENTER, TAIWAN NO. 34. LIN 5. DINGFU, LINKOU DIST., NEW TAIPEI CITY, TAIWAN, 24442, R.O.C. Tel:(02)26023052 Fax:(02)26010910 http://www.etc.org.tw ; e-mail : [email protected] Report Number : 13-05-RBF-025-01 ETC Report No. : 13-05-RBF-025-01 Sheet 1 of 26 Sheets FCC ID. : NTMAT-200ID Rev. No 2.0 TEST REPORT CERTIFICATION Applicant : OKAYO ELECTRONICS CO., LTD. No.2, Gongye 10 th Rd., Dali Dist., Taichung 41280, Taiwan Manufacture : OKAYO ELECTRONICS CO., LTD. No.2, Gongye 10 th Rd., Dali Dist., Taichung 41280, Taiwan Description of Device : a) Type of EUT : Audio Guide b) Trade Name : OKAYO c) Model No. : AT-200iD-MT d) Serial Model : AT-200iD e) Power Supply : 3.7 V Li-ion.1200 mAh rechargeable battery Regulation Applied : FCC Rules and Regulations Part 15 Subpart C I HEREBY CERTIFY THAT: The data shown in this report were made in accordance with the procedures given in ANSI C63.4, and the energy emitted by the device was founded to be within the limits applicable. I assume full responsibility for accuracy and completeness of these data. Note: 1. The result of the testing report relate only to the item tested. 2. The testing report shall not be reproduced expect in full, without the written approval of ETC. Summary of Tests Test Results Radiated Emission Pass Conducted Emission Pass ETC Report No. : 13-05-RBF-025-01 Sheet 2 of 26 Sheets FCC ID. : NTMAT-200ID Rev. No 2.0 Date Test Item Received : May 31, 2013 Date Test Campaign Completed : Jul. 08, 2013 Date of Issue : Aug. 19, 2013 Test Engineer : ( Vincent Chang ) Approve & Authorized : S. S. Liou, Section Manager EMC Dept. II of ELECTRONICS TESTING CENTER, TAIWAN ETC Report No. : 13-05-RBF-025-01 Sheet 3 of 26 Sheets FCC ID. : NTMAT-200ID Rev. No 2.0 Table of Contents Page 1 GENERAL INFORMATION ....................................................................................................... 4 1.1 Product Description...................................................................................................................... 4 1.2 Characteristics of Device ............................................................................................................. 4 1.3 Test Methodology ........................................................................................................................ 5 1.4 Test Facility.................................................................................................................................. 5 2 PROVISIONS APPLICABLE...................................................................................................... 6 2.1 Definition ..................................................................................................................................... 6 2.2 Requirement for Compliance ....................................................................................................... 7 2.3 Restricted Bands of Operation ..................................................................................................... 8 2.4 Labeling Requirement .................................................................................................................. 8 2.5 User Information .......................................................................................................................... 9 3. SYSTEM TEST CONFIGURATION ........................................................................................ 10 3.1 Justification ................................................................................................................................ 10 3.2 Devices for Tested System......................................................................................................... 10 4 RADIATED EMISSION MEASUREMENT ............................................................................ 11 4.1 Applicable Standard ................................................................................................................... 11 4.2 Measurement Procedure............................................................................................................. 11 4.3 Measuring Instrument ................................................................................................................ 13 4.4 Radiated Emission Data ............................................................................................................. 14 4.4.1 RF Portion ......................................................................................................................................... 14 4.4.2 Other Emission.................................................................................................................................. 15 4.5 Field Strength Calculation ......................................................................................................... 17 4.6 Photos of Radiation Measuring Setup........................................................................................ 18 5 CONDUCTED EMISSION MEASUREMENT ........................................................................ 19 5.1 Standard Applicable ................................................................................................................... 19 5.2 Measurement Procedure............................................................................................................. 19 5.3 Conducted Emission Data .......................................................................................................... 20 5.4 Result Data Calculation ............................................................................................................. 24 5.5 Conducted Measurement Equipment ...........................................................…

Text truncated - open the document above for the full version.

ETC Report No. : 13-05-RBF-025-01 Sheet 18 of 26 Sheets FCC ID. : NTMAT-200ID Rev. No 2.0 4.6 Photos of Radiation Measuring Setup ETC Report No. : 13-05-RBF-025-01 Sheet 25 of 26 Sheets FCC ID. : NTMAT-200ID Rev. No 2.0 5.6 Photos of Conduction Measuring Setup