OBKWTGTLWALKIE TALKIE

MAX LIGHT Report Number: MLT9811P15002FCC ID: OBKWTGTL Technology Lab MAX LIGHT Report Number: MLT9811P15002FCC ID: OBKWTGTL Technology Lab MAX LIGHT Report Number: MLT9811P15002FCC ID: OBKWTGTL Technology Lab

MAX LIGHT Report Number: MLT9811P15002FCC ID: OBKWTGTL Technology Lab Label Format: Label Position: FCC ID: OBKWTGTL This device complies with Part15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference,and (2) This device must accept any interference received ,including. Interference that may cause undesired operation. Model: WT-2,WT-3,WT-6,WT-24,WT-94,HAPPY MEAL MADE IN CHINA Equipment Label 4.8CMX1.2CM Rear View

Product : 49MHz WALKIE TALKIE Manufacture : GOLDEN TIME LIMITED. FCC ID : OBKWTGTL Model : LT-2, WT-3, WT-6, WT-24, WT-94, HAPPY MEAL Report No. : MLT9811P15002 Test Date : DEC.03,1998 Test By Max Light Technology Co.,Ltd. Room 5, 8F, No.125, Section 3 Roosevelt Road, Taipei, Taiwan., R.O.C. Tel: 886-2-363-2447 Fax: 886-2-363-2597 MAX LIGHT MEASUREMENT REPORT Page: 2 Report Number: MLT9811P15002FCC ID: OBKWTGTL Technology Lab Table of Contents : I. General 4. II. Conducted Emissions Requirements 9. III. Radiated Emissions Requirements 13. IV. Emissions Within Band Edges Measurement 15. Appendix I (EUT Test Setup) 17. MAX LIGHT MEASUREMENT REPORT Page: 3 Report Number: MLT9811P15002FCC ID: OBKWTGTL Technology Lab CERTIFICATION We here by verify that : The test data, data evaluation, test procedures and equipment configurations shown in this report were made in accordance with the procedures given in ANSI C63.4-1992. All test were conducted by MLT (Max Light Technology Co.,Ltd) Room 5, 8F, No.125, Section 3 Roosevelt Road, Taipei, Taiwan, R.O.C Also, we attest to the accuracy of each. We further submit that the energy emitted by the sample EUT tested as described in the report is in compliance with Class B conducted and radiated emission limit of FCC Rules Part 15 Subpart C Section 15.235. EUT: 49MHz WALKIE TALKIE Applicant: GOLDEN TIME LIMITED. FLAT 1704, 17F, GRAND BUSINESS PLAZA 153 WAI YIP ST., KWUN TONG, KOWLOON, Hong Kong . Manufacturer: GOLDEN TIME LIMITED. FLAT 1704, 17F, GRAND BUSINESS PLAZA 153 WAI YIP ST., KWUN TONG, KOWLOON, Hong Kong . Model No: LT-2, WT-3, WT-6, WT-24, WT-94, HAPPY MEAL FCC ID: OBKWTGTL Prepared by :CountryApproved by : Roger Country Huang Roger Chen MAX LIGHT MEASUREMENT REPORT Page: 4 Report Number: MLT9811P15002FCC ID: OBKWTGTL Technology Lab I. GENERAL 1.1 Introduction The following measurement report is submitted on behalf of GOLDEN TIME LIMITED. In support of an Intentional Periodic Radiator certification in accordance with Part2 Subpart J and Part 15 Subpart A And C of the Commission’s Rules and Regulations. 1.2 Description of EUT EUT: 49MHz WALKIE TALKIE Applicant: GOLDEN TIME LIMITED.. FLAT 1704, 17F, GRAND BUSINESS PLAZA 153 WAI YIP ST., KWUN TONG, KOWLOON, Hong Kong . Manufacturer: GOLDEN TIME LIMITED.. FLAT 1704, 17F, GRAND BUSINESS PLAZA 153 WAI YIP ST., KWUN TONG, KOWLOON, Hong Kong . Model No: LT-2, WT-3, WT-6, WT-24, WT-94, HAPPY MEAL FCC ID : OBKWTGTL Power Type: 9.0 V/DC(“6F22” Size Battery x 1) Frequency: 49.86MHz The EUT(LT-2, WT-3, WT-6, WT-24, WT-94, HAPPY MEAL) is 49MHz Walkie Talkie product. The operation frequency is 49.86MHz. While testing the EUT was adjusted at a position which transmit the maximum. MAX LIGHT MEASUREMENT REPORT Page: 5 Report Number: MLT9811P15002FCC ID: OBKWTGTL Technology Lab 1.3 Description of Support Equipment In order to construct the minimum system which required by the ANSI C63.4-1991, following equipments were used as the support units. N/A MAX LIGHT MEASUREMENT REPORT Page: 6 Report Number: MLT9811P15002FCC ID: OBKWTGTL Technology Lab 1.4 Configuration of System Under Test During testing the EUT(49MHz WALKIE TALKIE)’s Talk Button is pushed so RF out continuously from the EUT. EUT MAX LIGHT MEASUREMENT REPORT Page: 7 Report Number: MLT9811P15002FCC ID: OBKWTGTL Technology Lab 1.5 Test Procedure All measurements contained in this report were performed according to the techniques described in Measurement procedure ANSI C63.4-1992 "Measurement of Intentional Radiators." 1.6 General Test Condition The conditions under which the EUT operates were varied to determine their effect on the equipment's emission characteristics. The final configuration of the test system and the mode of operation used during these tests was chosen as that which produced the highest emission levels. However, only those conditions which the EUT was considered likely to encounter in normal use were investigated. MAX LIGHT MEASUREMENT REPORT Page: 8 Report Number: MLT9811P15002FCC ID: OBKWTGTL Technology Lab II. Conducted Emissions Requirements The EUT operates solely by the battery. According to the rule of Section 15.207(c), the EUT exempt to the power line conducted test. MAX LIGHT MEASUREMENT REPORT Page: 9 Report Number: MLT9811P15002FCC ID: OBKWTGTL Technology Lab III. Radiated Emissions Requirements 3.1 General & Setup : Prior to open-field testing, the EUT was placed in a shielded enclosure and scanned at a close distance to determine its emission characteristics. The physical arrangement of the EUT was varied (within the scope of arrangements likely to be encountered in actual use) to determine the effect on the unit's emanations in amplitude, directivity, and frequency. The exact system configuration which produced the highest emissions was noted so it could be reproduced later during the open-field tests. This was done to ensure that the final measurements would demonstrate the worst-case interference potential of the EUT. Final radiation measurements were made on a three-meter, open-field test site. The EUT system was placed on a nonconductive turntable which is 0.8 meters height, top surface 1.0 x 1.5 meter. The spectrum was examined from 30 MHz to 1000 MHz using an Hewlett Packard 8591EM Spectrum Analyzer, EMCO Biconical Antenna (Model 3142) for 30-1000MHz. At each frequency, the EUT was rotated 360 degrees, and the antenna was raised and lowered from one to four meters to find the maximum emission levels. Measurements were taken using both horizontal and vertical antenna polarization. Appropriate preamplifiers were used for improving sensitivity and precautions were taken to avoid overloading or desensitizing the spectrum analyzer. No post-detector video filters were used in the test. The spectrum analyzer's 6 dB bandwidth was set to 120 KHz, and the analyzer was operated in the quasi-peak detection mode. The highest emission amplitudes relative to the appropriate limit were measured and recorded in paragraph 3.6. 3.2 Test …

Text truncated - open the document above for the full version.