OGGK3MF2724SPEAKER

15” PORTABLE PARTY SPEAKER Model # BB2724 Instruction Manual Instrucciones en español incluidas 2 PLEASE READ THESE INSTRUCTIONS CAREFULLY BEFORE USING YOUR PARTY SPEAKER. KEEP THESE INSTRUCTIONS FOR FUTURE REFERENCE. Your Speaker has an internal rechargeable battery. Improper usage may result in the Speaker becoming hot, ignite or burst and cause injury if exposed to conditions of abuse. Be sure to follow the safety warnings listed below: 1. Do not assemble, throw away or damage the Party Speaker. 2. Store the Party Speaker in a dry place, keeping it away from damp corrosive materials and environments such as salt air. 3. Keep the Speaker away from direct sunlight, fire, and high voltage equipment. Do not store the Speaker inside a car during hot weather. Remember a closed car acts as a greenhouse allow- ing the inside temperature to possibly reach over 200F. 4. The Party Speaker is not a toy. Please keep it out of the reach of young children. Please do not discard this rechargeable device as trash. Consult your local waste collection agency for proper disposal or recycling methods. You may also contact *Call2Recycle” at 877-273-2925 or online at *call2Recycle.org* for a battery recycling drop off location near you. Charging the battery This device has an internal, rechargeable battery. 1. Plug the charger cable into the Party Speaker. 2. Connect the charger to a USB power source. The red indicator light will display during charging. Charging does not start, disconnect the charger plug it in again, and retry. Charging the battery fully may take up to 3 hours. 3. When the battery is fully charged, the red indicator light will turn off. Disconnect the charger from the USB power source and the Party Speaker. The fully charged battery has power for up to 4-5 hours of music time or up to 240 hours of standby time. However, the talk and standby times may vary when used with different devices, settings, and environments. Battery Information Your device is powered by a rechargeable battery. The full performance of a new battery is achieved only after two to three complete charge and discharge cycles. The battery can be charged and discharged hundreds of times, but it will eventually wear out. • Do not leave a fully charged battery connected to a charger, overcharging may shorten its lifetime. If left unused, a fully charged battery will lose its charge over time. • Never use any charger that is damaged. • Leaving the device in hot or cold places will reduce the capacity and lifetime of the battery. Optimal temperature for the battery is between 59 ̊F and 77 ̊F. A device with a hot or cold battery may not work temporarily, even when the battery is fully charged. • Do not dispose of batteries in a fire as they may explode. Batteries may also explode if damaged. Always dispose of batteries according to local regulations. Please recycle. Do not dispose as household waste. 3 POR FAVOR LEA ESTAS INSTRUCCIONES CUIDADOSAMENTE ANTES DE USAR EL ALTAVOZ DE SU FIESTA. CONSERVE ESTAS INSTRUCCIONES PARA FUTURAS REFERENCIAS. Su altavoz tiene una batería interna recargable. El uso incorrecto puede provocar que el al- tavoz se caliente, se encienda o explote y cause lesiones si se expone a condiciones de abuso. Asegúrese de seguir las advertencias de seguridad que se enumeran a continuación: 1. No monte, tire ni dañe el altavoz del partido. 2. Guarde el altavoz para fiestas en un lugar seco, manteniéndolo alejado de materiales corro- sivos húmedos y entornos como el aire salado. 3. Mantenga el altavoz alejado de la luz solar directa, fuego y equipos de alto voltaje. No guarde el altavoz dentro de un automóvil cuando haga calor. Recuerde que un automóvil cerra- do actúa como un invernadero permitiendo que la temperatura interior alcance posiblemente más de 200F. 4. El orador del partido no es un juguete. Manténgalo fuera del alcance de los niños pequeños. No deseche este dispositivo recargable como basura. Consulte a su agencia local de recolección de residuos para la eliminación adecuada o métodos de reciclaje. También puede contactar * Call2Recycle ”en 877-273-2925 o en línea en * call2Recycle.org * para obtener una ubicación de reciclaje de bat- erías cerca de usted. Charge de la batterie Cet appareil est doté d’une batterie interne rechargeable. 1. Branchez le câble du chargeur sur le haut-parleur de parti. 2. Connectez le chargeur à une source d’alimentation USB. Le voyant rouge s’affiche pendant le chargement. La charge ne commence pas, débranchez à nouveau le chargeur, puis réessayez. Le chargement complet de la batterie peut prendre jusqu’à 3 heures. 3. Lorsque la batterie est complètement chargée, le voyant rouge s’éteint. Débranchez le chargeur de la source d’alimentation USB et du haut-parleur de parti. La batterie complètement chargée est alimentée pendant 4 à 5 heures de musique ou jusqu’à 240 heures en veille. Toute- fois, les temps de conversation et de veille peuvent varier lorsqu’ils sont utilisés avec différents périphériques, paramètres et environnements. Informations sur la batterie Votre appareil est alimenté par une batterie rechargeable. Les performances optimales d’une nouvelle batterie ne sont atteintes qu’après deux à trois cycles complets de charge et de décharge. La batterie peut être chargée et déchargée des centaines de fois, mais elle finira par s’user. • Ne laissez pas une batterie complètement chargée connectée à un chargeur, la surcharge ris- que de réduire sa durée de vie. Si elle reste inutilisée, une batterie complètement chargée perd sa charge avec le temps • N’utilisez jamais de chargeur endommagé. • Laisser l’appareil dans des endroits chauds ou froids réduira la capacité et la durée de vie de la batterie. La température optimale pour la batterie est comprise entre 59 ̊F et 77 ̊F. Un appareil avec une batterie chaude ou froide peut ne pas fonctionner temporairement, même lorsque la batterie est complètement chargée. • Ne jetez pas les piles au feu, elles pourraient explose…

Text truncated - open the document above for the full version.

< GUANGZHOU PANYU MINFU SPEAKER FACTORY > Office of Engineering Technology Federal Communications Commission 7435 Oakland Mills Road Columbia, MD21046 Date: 2020-05-11 Subject; Request for Long Term Confidentiality FCC ID: OGGK3MF2724 To Whom It May Concern, Pursuant to the provisions of the Commission’s rules Title 47 Sections §0.457 and §0.459, we are requesting the Commission to withhold the following attachment(s) as confidential documents from public disclosure indefinitely. These documents contain detailed system and equipment descriptions and are considered as proprietary information in operation of the equipment. The public disclosure of these documents might be harmful to our company and would give competitors an unfair advantage in the market. Schematic Diagram Block Diagram Operational Description It is our understanding that all measurement test reports, FCC ID label format and correspondence during the certification review process cannot be granted as confidential documents and this information will be available for public review once the grant of equipment authorization is issued. Sincerely, Signature: Name: Pan FuXin Title: Manager

GUANGZHOU PANYU MINFU SPEAKER FACTORY Letter of Authorization Company: GUANGZHOU PANYU MINFU SPEAKER FACTORY Address: DONG SHENG SAN HENG RD., CHADONG, SHIJI, PANYU DIS, GUANGZHOU, China Product Name: SPEAKER Model Number(s): BB2724 Product Description: SPEAKER We authorize MiCOM Labs Inc., 575 Boulder Court, Pleasanton, California 94566, USA, to act on our behalf on all matters concerning the certification of above named equipment. We declare that MiCOM Labs Inc. is allowed to forward all information related to the approval and certification of equipment to the regulatory agencies as required and to discuss any issues concerning the approval application. Any and all acts carried out by MiCOM Labs on our behalf shall have the same effect as acts of our own. Signature: Date: 2020-05-11 Name: Pan FuXin Title: Manager Company: GUANGZHOU PANYU MINFU SPEAKER FACTORY

Test model number: BB2724

Model No.: BB2724 Label location

Test model number: BB2724

Global United Technology Services Co., Ltd. Report No.: GTS202004000172F01 + TEST REPORT Applicant: GUANGZHOU PANYU MINFU SPEAKER FACTORY Address of Applicant: DONG SHENG SAN HENG RD., CHADONG, SHIJI, PANYU DIS, GUANGZHOU, China Manufacturer/Factory: GUANGZHOU PANYU MINFU SPEAKER FACTORY Address of Manufacturer/Factory: DONG SHENG SAN HENG RD., CHADONG, SHIJI, PANYU DIS, GUANGZHOU, China Equipment Under Test (EUT) Product Name: SPEAKER Model No.: BB2724 Trade Mark: Billboard FCC ID: OGGK3MF2724 Applicable standards: FCC CFR Title 47 Part 15 Subpart C Section 15.249 Date of sample receipt: April 24, 2020 Date of Test: April 24-28, 2020 Date of report issued: April 28, 2020 Test Result : PASS * * In the configuration tested, the EUT complied with the standards specified above. Authorized Signature: Robinson Lo Laboratory Manager This results shown in this test report refer only to the sample(s) tested, this test report cannot be reproduced, except in full, without prior written permission of the company. The report would be invalid without specific stamp of test institute and the signatures of compiler and approver. Page 1 of 28 Report No.: GTS202004000172F01 2 Version Version No. Date Description 00 April 28, 2020 Original Prepared By: Date: April 28, 2020 Project Engineer Check By: Date: April 28, 2020 Reviewer Global United Technology Services Co., Ltd. No. 123- 128, Tower A, Jinyuan Business Building, No.2, Laodong Industrial Zone, Xixiang Road, Baoan District, Shenzhen, Guangdong, China 518102 Telephone: +86 (0) 755 2779 8480 Fax: +86 (0) 755 2779 8960 Page 2 of 28 Report No.: GTS202004000172F01 3 Contents Page 1 COVER PAGE ............................................................................................................................................ 1 2 VERSION .................................................................................................................................................. 2 3 CONTENTS .............................................................................................................................................. 3 4 TEST SUMMARY ..................................................................................................................................... 4 4.1 MEASUREMENT UNCERTAINTY ............................................................................................................ 4 5 GENERAL INFORMATION ...................................................................................................................... 5 5.1 GENERAL DESCRIPTION OF EUT ......................................................................................................... 5 5.2 TEST MODE ........................................................................................................................................ 7 5.3 DESCRIPTION OF SUPPORT UNITS ....................................................................................................... 7 5.4 DEVIATION FROM STANDARDS ............................................................................................................. 7 5.5 ABNORMALITIES FROM STANDARD CONDITIONS ................................................................................... 7 5.6 TEST FACILITY .................................................................................................................................... 8 5.7 TEST LOCATION ................................................................................................................................. 8 5.8 ADDITIONAL INSTRUCTIONS ................................................................................................................. 8 6 TEST INSTRUMENTS LIST ..................................................................................................................... 9 7 TEST RESULTS AND MEASUREMENT DATA .................................................................................... 11 7.1 ANTENNA REQUIREMENT ................................................................................................................... 11 7.2 CONDUCTED EMISSIONS ................................................................................................................... 12 7.3 RADIATED EMISSION METHOD ........................................................................................................... 15 7.3.1 Field Strength of The Fundamental Signal ................................................................................ 17 7.3.2 Spurious emissions .................................................................................................................... 18 7.3.3 Bandedge emissions.................................................................................................................. 23 7.4 20DB OCCUPY BANDWIDTH .............................................................................................................. 25 8 TEST SETUP PHOTO ............................................................................................................................ 28 9 EUT CONSTRUCTIONAL DETAILS ..................................................................................................... 28 Global United Technology Services Co., Ltd. No. 123- 128, Tower A, Jinyuan Business Building, No.2, Laodong Industrial Zone, Xixiang Road, Baoan District, Shenzhen, Guangdong, China 518102 Telephone: +86 (0) 755 2779 8480 Fax: +86 (0) 755 2779 8960 Page 3 of 28 Report No.: GTS202004000172F01 4 Test Summary Test Item Section in CFR 47 Result Antenna requirement 15.203 Pass AC Power Line Conducted Emission 15.207 Pass Field strength of the fundamental signal 15.249 (a) Pass Spurious emissions 15.249 (a) (d)/15.209 Pass Band edge 15.249 (d)/15.205 Pass 20dB Occupied Bandwidth 15.215 (c) Pass Pass: The EUT complies with the essential requirements in the standard. Remark ：Test according to ANSI C63.10:2013. 4.1 Measurement Uncertainty Test Item Frequency Range Measure…

Text truncated - open the document above for the full version.

Global United Technology Services Co., Ltd. Report No.: GTS202004000172F02 TEST REPORT Applicant: GUANGZHOU PANYU MINFU SPEAKER FACTORY Address of Applicant: DONG SHENG SAN HENG RD., CHADONG, SHIJI, PANYU DIS, GUANGZHOU, China Manufacturer/Factory: GUANGZHOU PANYU MINFU SPEAKER FACTORY Address of Manufacturer/Factory: DONG SHENG SAN HENG RD., CHADONG, SHIJI, PANYU DIS, GUANGZHOU, China Equipment Under Test (EUT) Product Name: SPEAKER Model No.: BB2724 Trade Mark: Billboard FCC ID: OGGK3MF2724 Applicable standards: FCC CFR Title 47 Part 15 Subpart C Section 15.249 Date of sample receipt: April 24, 2020 Date of Test: April 24-28, 2020 Date of report issued: April 28, 2020 Test Result : PASS * * In the configuration tested, the EUT complied with the standards specified above. Authorized Signature: Robinson Lo Laboratory Manager This results shown in this test report refer only to the sample(s) tested, this test report cannot be reproduced, except in full, without prior written permission of the company. The report would be invalid without specific stamp of test institute and the signatures of compiler and approver. Page 1 of 26 Report No.: GTS202004000172F02 2 Version Version No. Date Description 00 April 28, 2020 Original Prepared By: Date: April 28, 2020 Project Engineer Check By: Date: April 28, 2020 Reviewer Global United Technology Services Co., Ltd. No. 123- 128, Tower A, Jinyuan Business Building, No.2, Laodong Industrial Zone, Xixiang Road, Baoan District, Shenzhen, Guangdong, China 518102 Telephone: +86 (0) 755 2779 8480 Fax: +86 (0) 755 2779 8960 Page 2 of 26 Report No.: GTS202004000172F02 3 Contents Page 1 COVER PAGE ............................................................................................................................................ 1 2 VERSION .................................................................................................................................................. 2 3 CONTENTS .............................................................................................................................................. 3 4 TEST SUMMARY ..................................................................................................................................... 4 4.1 MEASUREMENT UNCERTAINTY ............................................................................................................ 4 5 GENERAL INFORMATION ...................................................................................................................... 5 5.1 GENERAL DESCRIPTION OF EUT ......................................................................................................... 5 5.2 TEST MODE ........................................................................................................................................ 7 5.3 DESCRIPTION OF SUPPORT UNITS ....................................................................................................... 7 5.4 DEVIATION FROM STANDARDS ............................................................................................................. 7 5.5 ABNORMALITIES FROM STANDARD CONDITIONS ................................................................................... 7 5.6 TEST FACILITY .................................................................................................................................... 7 5.7 TEST LOCATION ................................................................................................................................. 7 5.8 ADDITIONAL INSTRUCTIONS ................................................................................................................. 7 6 TEST INSTRUMENTS LIST ..................................................................................................................... 8 7 TEST RESULTS AND MEASUREMENT DATA .................................................................................... 10 7.1 ANTENNA REQUIREMENT ................................................................................................................... 10 7.2 CONDUCTED EMISSIONS ................................................................................................................... 11 7.3 RADIATED EMISSION METHOD ........................................................................................................... 14 7.3.1 Field Strength of The Fundamental Signal ................................................................................ 16 7.3.2 Spurious emissions .................................................................................................................... 17 7.3.3 Bandedge emissions.................................................................................................................. 22 7.4 20DB OCCUPY BANDWIDTH .............................................................................................................. 24 8 TEST SETUP PHOTO ............................................................................................................................ 26 9 EUT CONSTRUCTIONAL DETAILS ..................................................................................................... 26 Global United Technology Services Co., Ltd. No. 123- 128, Tower A, Jinyuan Business Building, No.2, Laodong Industrial Zone, Xixiang Road, Baoan District, Shenzhen, Guangdong, China 518102 Telephone: +86 (0) 755 2779 8480 Fax: +86 (0) 755 2779 8960 Page 3 of 26 Report No.: GTS202004000172F02 4 Test Summary Test Item Section in CFR 47 Result Antenna requirement 15.203 Pass AC Power Line Conducted Emission 15.207 Pass Field strength of the fundamental signal 15.249 (a) Pass Spurious emissions 15.249 (a) (d)/15.209 Pass Band edge 15.249 (d)/15.205 Pass 20dB Occupied Bandwidth 15.215 (c) Pass Remarks: 1. Test according to ANSI C63.10: 2013. 2. Pass: The EUT complies with the essential requirements in the standard. 4.1 Measurement Uncertainty Test Item Frequency Range M…

Text truncated - open the document above for the full version.

Test Model No.: BB2724 Radiated Emission Conducted Emission