OGGM-1509Bluetooth Speaker

WASP1100WBT WASP1100WBT DISPLAYER USB/SD MODE 321 WASP1100WBT WASP1100WBT WIRELESS MICROPHONE FCC Statement This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: -- Reorient or relocate the receiving antenna. -- Increase the separation between the equipment and receiver. -- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. -- Consult the dealer or an experienced radio/TV technician for help.

Label Sample FCC ID : OGGM-1509 This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation.

LABEL LOCATION

FCCID: OGGM-1509 Report Number: HST201206-1597-FCC Page 1 of 83 Test Report Applicant: Guangzhou Panyu Minfu Speaker Factory Address of Applicant: Dong Sheng San Heng RD., Chadong, Shiji, Panyu Dist., Guangzhou, Guangdong, China Equipment Under Test (EUT): EUT Name: Bluetooth Speaker Model No.: WASP1100WBT, WASP1300WBT Trade Mark: N/A Serial No.: Not supplied by client Standards: FCC Part 15 Subpart C: 2010 section 15.247 Date of Receipt: May 16, 2012 Date of Test: May 16 to Jun. 3, 2012 Date of Issue: July 20, 2012 Test Result : PASS* z In the configuration tested, the EUT complied with the standards specified above. Authorized Signature: Henly Xie / Manager This report refers to the General Conditions for Inspection and Testing Services, printed overleaf This report details the results of the testing carried out on one sample. The results contained in this test report do not relate to other samples of the same product. The manufacturer should ensure that all products in series production are in conformity with the product sample detailed in this report. This report may only be reproduced and distributed in full. If the product in this report is used in any configuration other than that detailed in the report, the manufacturer must ensure the new system complies with all relevant standards. The report must not be used by the client to claim product certification, approval, or endorsement by NVLAP, NIST, or any agency of the federal government. All test results in this report can be traceable to National or International Standards. The test report prepare by: Guangzhou Huesent Testing Service Co., Ltd. No.91, Dongguanzhuang Road, Tianhe District, Guangzhou, China. Tel: 86-20-28263298 Fax: 86-20-28263237 http://www.hst.org.cn E-mail: [email protected] Report Number: HST201206-1597-FCC Page 2 of 83 Contents 1 TEST SUMMARY .................................................................................................3 2 GENERAL INFORMATION ...................................................................................4 2.1 Client Information ...........................................................................................................4 2.2 General Description of E.U.T. .........................................................................................4 2.3 Details of E.U.T...............................................................................................................4 2.4 Description of Support Units...........................................................................................4 2.5 Test Location ..................................................................................................................5 2.6 Deviation from Standards ...............................................................................................5 2.7 Abnormalities from Standard Conditions ........................................................................5 2.8 Other Information Requested by the Customer ..............................................................5 2.9 Measurement Uncertainty ..............................................................................................5 3 EQUIPMENTS USED DURING TEST ..................................................................6 4 TEST RESULTS ...................................................................................................7 4.1 E.U.T. test conditions......................................................................................................7 4.2 Antenna equirement .....................................................................................................10 4.3 Occupied Bandwidth .................................................................................................... 11 4.4 Carrier Frequencies Separated ....................................................................................16 4.5 Hopping Channel Number............................................................................................20 4.6 Dwell Time....................................................................................................................22 4.7 Pseudorandom Frequency Hopping Sequence............................................................32 4.7.1 Standard requirement ......................................................................................32 4.7.2 EUT Pseudorandom Frequency Hopping Sequence.......................................32 4.8 Maximum Peak Output Power .....................................................................................33 4.9 Conducted Spurious Emissions ...................................................................................38 4.10 Radiated Spurious Emissions ......................................................................................41 4.10.1 Harmonic and other spurious emissions .........................................................44 4.11 Radiated Emissions which fall in the restricted bands .................................................53 4.12 Band Edges Requirement ............................................................................................57 4.13 Conducted Emissions at Mains Terminals 150 kHz to 30 MHz....................................61 4.13.1 Measurement Data ..........................................................................................63 5 APPENDIX .........................................................................................................65 5.1 Photographs of the Test Arrangement .........................................................................65 5.2 Photographs of EUT Constructional Details ................................................................67 5.3 Antenna Photo .............................................................................................................83 Report Number: HST201206-1597-FCC Page 3 of 83 1 Test Summary Te s t Test Requirement Te s t m e t h o d Result Antenna Requirement FCC PA…

Text truncated - open the document above for the full version.