OGPJSE99

• The test results reported in this report shall refer only to the sample actually tested and shall not refer or be deemed to refer to bulk from which such a sample may be said to have been obtained. • This report shall not be reproduced except in full without prior authorization from Intertek Testing Services Hong Kong Limited FCC ID : OGPJSE99 Applicant Name Application For Certification (FCC ID: OGPJSE99) RF Lighting Device WO# 9811126.dot CKL/at May 19, 1999 INTERTEK TESTING SERVICES FCC ID: OGPJSE99 i LIST OF EXHIBITS INTRODUCTION EXHIBIT 1:General Description EXHIBIT 2:System Test Configuration EXHIBIT 3:Emission Results EXHIBIT 4:Equipment Photographs EXHIBIT 5:Product Labelling EXHIBIT 6:Technical Specifications EXHIBIT 7:Instruction Manual EXHIBIT 8:Miscellaneous Information INTERTEK TESTING SERVICES FCC ID: OGPJSE99 ii MEASUREMENT/TECHNICAL REPORT Shenzhen Jiashi Electronics Co. Ltd. MODEL: Jiashi JS9812 Series 7W, 9W, 11W, 13W, 15W, 18W, 20W, 22W, 24W FCC ID: OGPJSE99 May 19, 1999 This report concerns (check one:)Original Grant X Class II Change Equipment Type: RF Lighting Device Deferred grant requested per 47 CFR 0.457(d)(1)(ii)?Yes No X If yes, defer until: date Company Name agrees to notify the Commission by: date of the intended date of announcement of the product so that the grant can be issued on that date. Report prepared by:C. K. Lam Intertek Testing Services 2/F., Garment Center, 576, Castle Peak Road, HONG KONG Phone:852-2173-8512 Fax:852-2742-9149 INTERTEK TESTING SERVICES FCC ID: OGPJSE99 iii Table of Contents 1.0 General Description ................................................................................................................. 2 1.1 Product Description.............................................................................................................. 2 1.2 Related Submittal(s) Grants .................................................................................................2 1.3 Test Methodology ................................................................................................................ 3 1.4 Test Facility.......................................................................................................................... 3 1.5 Equipment List..................................................................................................................... 4 2.0 System Test Configuration ...................................................................................................... 6 2.1 Justification .......................................................................................................................... 6 2.2 EUT Exercising Software.....................................................................................................6 2.3 Special Accessories.............................................................................................................. 6 2.4 Equipment Modification ......................................................................................................7 2.5 Support Equipment List and Description.............................................................................. 7 3.0 Emission Results ....................................................................................................................... 9 3.1 Field Strength Calculation ..................................................................................................10 3.1 Field Strength Calculation (cont)........................................................................................ 11 3.2 Radiated Emission Configuration Photograph.................................................................... 12 3.3 Radiated Emission Data .....................................................................................................13 3.4 Line Conducted Configuration Photograph ....................................................................... 16 3.5 Line Conducted Emission Data...............................................................................................18 4.0 Equipment Photographs ........................................................................................................ 20 5.0 Product Labelling ................................................................................................................... 22 6.0 Technical Specifications ......................................................................................................... 24 7.0 Instruction Manual ................................................................................................................ 26 INTERTEK TESTING SERVICES FCC ID: OGPJSE99 iv List of attached file Exhibit typeFile Descriptionfilename Cover LetterLetter of Agencyletter.pdf Test ReportTest Reportreport.doc Test Setup PhotoRadiated Emissionradiated1.jpg, radiated2.jpg Test Setup PhotoConducted Emissionconduct1.jpg to conduct3.jpg Test ReportConducted Emission Test Resultconduct.pdf External PhotoExternal Photoophoto1.jpg, ophoto2.jpg Internal PhotoInternal Photoiphoto1.jpg to iphoto4.jpg Block DiagramBlock Diagramblock.pdf SchematicsCircuit Diagramcircuit.pdf ID Label/LocationLabel Artwork and Locationlabel.pdf User ManualUser Manualmanual.pdf INTERTEK TESTING SERVICES FCC ID: OGPJSE99 1 EXHIBIT 1 GENERAL DESCRIPTION INTERTEK TESTING SERVICES FCC ID: OGPJSE99 2 1.0 General Description 1.1Product Description The equipment under test (EUT) is a self-ballasted lamp, model: Jiashi JS9812 Series 7W, 9W, 11W, 13W, 15W, 18W, 20W, 22W and 24W. The EUT is powered by AC 120V, 60Hz and operated with 20kHz to activated the fluorescent lamp. The self-ballasted lamps have two different shape of tubes. The lamps with 7W to 22W are 3U shape tubes which share the same circuit but are in different power. Whilst the lamp 24W is a screw shape tube. The difference in circuit between these two type of lamps is an additional capacitor (C10) adding across the a.c. terminal of the highest powered …

Text truncated - open the document above for the full version.