OKVMT300Low Power Fixed TVBD

MT-300 Pico Broadcaster Operator Manual __ 1 MT300 Pico Broadcaster Version 1.0 OPERATOR MANUAL MT-300 Pico Broadcaster Operator Manual __ 2 August 21, 2012 Table of Contents 1. PREFACE............................................................................................................................................ 3 2. IMPORTANT NOTICE ..................................................................................................................... 3 3. INTRODUCTION............................................................................................................................... 3 3.1 OVERVIEW ................................................................................................................................... 3 3.2 DEFAULT SETTINGS...................................................................................................................... 4 3.3 GENERAL DESCRIPTION ............................................................................................................... 4 3.4 INTELLECTUAL PROPERTY WARNING........................................................................................... 5 3.5 SYSTEM ARCHITECTURE ................................................................................................................... 5 3.6 APPLICATIONS IN DIGITAL SIGNAGE ................................................................................................. 6 3.7 LIST OF ABBREVIATIONS ................................................................................................................... 6 4. INSTALLATION ................................................................................................................................ 7 4.1 FRONT/REAR PANEL INTERFACE ....................................................................................................... 7 4.2 SETTING UP MT300 FOR FIRST TIME USE .......................................................................................... 7 4.3 USING YOUR PICO BROADCASTER ...................................................................................................12 5. TROUBLE SHOOTING ..................................................................................................................14 5.1 HARDWARE SETUP ..........................................................................................................................14 5.2 SET UP AND TEST ETHERNET CONNECTION. .....................................................................................14 5.3 STREAM CONTENT TO DEVICE .....................................................................................................15 Copyright © 2012 by MELD Technology Inc. Information furnished in this document is believed to be accurate and reliable, but MELD assumes no responsibility for any errors that many appear in this material. MT-300 Pico Broadcaster Operator Manual __ 3 1. Preface This document provides operator information on how to set up the MT300 (Ethernet to Broadcast) Pico Broadcaster. This device requires professional installation. 2. IMPORTANT NOTICE This equipment has been tested and found to comply with the rules for TV bands devices, pursuant to part 15 of the FCC rules. These rules are designed to provide reasonable protection against harmful interference. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: (1) Reorient or relocate the receiving antenna. (2) Increase the separation between the equipment and receiver. (3) Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. (4) Consult the manufacturer, dealer or an experienced radio/TV technician for help. 3. Introduction The Meld Technology MT300 White Space radio must be professionally installed by an trained installer. The installation must be in accordance with 47 CFR Part 15 Subpart H and the instructions contained in this manual. Only the following components are approved for use with the radio. Power Supply: Stontronics 3A-401WP12 Antenna: U Tek Technology Co. EA-79X-1 3.1 Overview MELD develops Pico Broadcast products for wirelessly distributing content to any DTV ever made for the North American market using newly opened white space frequencies and broadcast standard modulation methods. The advantages of Personal Broadcast based solutions are: Lower cost labor for installation, modification and support MT-300 Pico Broadcaster Operator Manual __ 4 Economy of scale using standard DTV receivers and components verses other specialized non-standard receivers and communication methods. MELD’s Pico Broadcaster sends live full HD content wirelessly to any number of DTVs located in an unobstructed effective range of 360 feet, about the size of a football field. No cabling or infrastructure equipment investment needed. 3.2 Default Settings. The device has two IP address. 1) System Control CPU (default) IP address: 192.168.1.194 Gateway IP: 192.168.1.254 2) Digital Modulator (default IP address) IP address: 192.168.1.193 Port: 5002 3) Power levels: Output Power: 11 is the highest rated power 01 is the lowest available power 3.3 General Description MT-300 Pico Broadcaster Operator Manual __ 5 Figure 1 - Typical Setup for Device configuration and TVWS access The MT300 is an easy to use Fixed TV bands device using a VSB modulator that is designed to provide low-power transmission of a DTV compatible signal over a limited area. It is designed to not interfere with licensed broadcast transmissions and complies with the FCC CFR 47 Part 15 subpart H rules for TV Band devices. It is designed to …

Text truncated - open the document above for the full version.

MT-300 Pico Broadcaster Operator Manual __ 1 MT300 Pico Broadcaster Version 1.2 OPERATOR MANUAL MT-300 Pico Broadcaster Operator Manual __ 2 Table of Contents 1. PREFACE............................................................................................................................................ 3 2. IMPORTANT NOTICES ................................................................................................................... 3 FCC PART 15 INFORMATION TO THE USER ................................................................................................. 3 RF EXPOSURE............................................................................................................................................. 3 3. INTRODUCTION............................................................................................................................... 4 3.1 OVERVIEW ................................................................................................................................... 4 3.2 DEFAULT SETTINGS ..................................................................................................................... 5 3.3 GENERAL DESCRIPTION ............................................................................................................... 5 3.4 INTELLECTUAL PROPERTY WARNING........................................................................................... 5 3.5 SYSTEM ARCHITECTURE ................................................................................................................... 6 3.6 APPLICATIONS IN DIGITAL SIGNAGE ................................................................................................. 7 3.7 LIST OF ABBREVIATIONS ................................................................................................................... 7 4. INSTALLATION ................................................................................................................................ 8 4.1 FRONT/REAR PANEL INTERFACE ....................................................................................................... 8 4.2 SETTING UP MT300 FOR FIRST TIME USE .......................................................................................... 8 4.3 USING YOUR PICO BROADCASTER ...................................................................................................13 5. STREAMING .....................................................................................................................................14 5.1 STREAM CONTENT TO DEVICE ..............................................................................................................14 5.2 TUNE THE TV RECEIVER .....................................................................................................................16 6. TROUBLE SHOOTING ...................................................................................................................17 6.1 HARDWARE SETUP ..........................................................................................................................17 6.2 SET UP AND TEST ETHERNET CONNECTION. .....................................................................................17 6.3 TUNING THE TV RECEIVER .............................................................................................................18 Copyright © 2012 by MELD Technology Inc. Information furnished in this document is believed to be accurate and reliable, but MELD assumes no responsibility for any errors that many appear in this material. MT-300 Pico Broadcaster Operator Manual __ 3 1. Preface This document provides operator information on how to set up the MT300 (Ethernet to Broadcast) Pico Broadcaster. This device requires professional installation and the use of tools and procedures for determining location, minimum power requirements. 2. IMPORTANT NOTICES FCC Part 15 Information to the User Caution: Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. Note: This equipment has been tested and found to comply with the rules for TV bands devices, pursuant to part 15 of the FCC rules. These rules are designed to provide reasonable protection against harmful interference. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: (1) Reorient or relocate the receiving antenna. (2) Increase the separation between the equipment and receiver. (3) Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. (4) Consult the manufacturer, dealer or an experienced radio/TV technician for help. RF Exposure The radio described in this manual transmits RF energy. The concentrated energy from the antenna may pose a health hazard. All antennas used with this radio must be installed to provide a minimum separation from all persons of 40 cm (15.7 inches). The above separation distance must be maintained at all times. More information can be obtained from the FCC at the following website: http://www.fcc.gov/Bureaus/Engineering_Technology/Documents/bulletins/oet65/oet65.pdf . MT-300 Pico Broadcaster Operator Manual __ 4 3. Introduction The Meld Technology MT300 White Space radio must be professionally installed by a trained installer. The installation must be in accordance with 47 CFR Part 15 Subpart H and the instructions contained in this manual. Only the following components are approved for use with the radio. Power Supply: Stontronics 3A-401WP12 Antenna: U Tek Technology Co. EA-79X-1 3.1 Over…

Text truncated - open the document above for the full version.

MT-300 Pico Broadcaster Operator Manual __ 1 MT300 Pico Broadcaster Version 1.3 OPERATOR MANUAL MT-300 Pico Broadcaster Operator Manual __ 2 Table of Contents 1. PREFACE............................................................................................................................................ 3 2. IMPORTANT NOTICES ................................................................................................................... 3 FCC PART 15 INFORMATION TO THE USER ................................................................................................. 3 RF EXPOSURE............................................................................................................................................. 3 3. INTRODUCTION............................................................................................................................... 4 3.1 OVERVIEW ................................................................................................................................... 4 3.2 GENERAL DESCRIPTION ............................................................................................................... 5 3.4 INTELLECTUAL PROPERTY WARNING........................................................................................... 5 3.5 SYSTEM ARCHITECTURE ................................................................................................................... 5 3.6 APPLICATIONS IN DIGITAL SIGNAGE ................................................................................................. 7 3.7 LIST OF ABBREVIATIONS ................................................................................................................... 7 4. INSTALLATION ................................................................................................................................ 8 4.1 FRONT/REAR PANEL INTERFACE ....................................................................................................... 8 4.2 SETTING UP THE MT300 FOR FIRST TIME USE ................................................................................... 9 4.3 USING YOUR PICO BROADCASTER ...................................................................................................15 5. STREAMING .....................................................................................................................................16 5.1 STREAM CONTENT TO DEVICE ..............................................................................................................16 5.2 TUNE THE TV RECEIVER .....................................................................................................................18 6. TROUBLE SHOOTING ...................................................................................................................19 6.1 HARDWARE SETUP ..........................................................................................................................19 6.2 SET UP AND TEST ETHERNET CONNECTION. .....................................................................................19 6.3 TUNING THE TV RECEIVER .............................................................................................................20 Copyright © 2012 by MELD Technology Inc. Information furnished in this document is believed to be accurate and reliable, but MELD assumes no responsibility for any errors that many appear in this material. MT-300 Pico Broadcaster Operator Manual __ 3 1. Preface This document provides operator information on how to set up the MT300 (Ethernet to Broadcast) Pico Broadcaster. This device requires professional installation and the use of tools and procedures for determining location, minimum power requirements. 2. IMPORTANT NOTICES FCC Part 15 Information to the User Caution: Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. Note: This equipment has been tested and found to comply with the rules for TV bands devices, pursuant to part 15 of the FCC rules. These rules are designed to provide reasonable protection against harmful interference. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: (1) Reorient or relocate the receiving antenna. (2) Increase the separation between the equipment and receiver. (3) Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. (4) Consult the manufacturer, dealer or an experienced radio/TV technician for help. RF Exposure The radio described in this manual transmits RF energy. The concentrated energy from the antenna may pose a health hazard. All antennas used with this radio must be installed to provide a minimum separation from all persons of 40 cm (15.7 inches). The above separation distance must be maintained at all times. More information can be obtained from the FCC at the following website: http://www.fcc.gov/Bureaus/Engineering_Technology/Documents/bulletins/oet65/oet65.pdf . MT-300 Pico Broadcaster Operator Manual __ 4 3. Introduction The Meld Technology MT300 White Space radio must be professionally installed by a trained installer. The installation must be in accordance with 47 CFR Part 15 Subpart H and the instructions contained in this manual. Only the following components are approved for use with the radio. Power Supply: Stontronics 3A-401WP12 Antenna: U Tek Technology Co. EA-79X-1 3.1 Overview MELD develops Pico Broadcast products for wirelessly distributing content to any DTV ever made for the North American market using newly op…

Text truncated - open the document above for the full version.

MT-300 Pico Broadcaster Operator Manual __ 1 MT300 Pico Broadcaster Version 1.4 OPERATOR MANUAL MT-300 Pico Broadcaster Operator Manual __ 2 Table of Contents 1. PREFACE............................................................................................................................................ 3 2. IMPORTANT NOTICES ................................................................................................................... 3 FCC PART 15 INFORMATION TO THE USER ................................................................................................. 3 RF EXPOSURE............................................................................................................................................. 3 3. INTRODUCTION............................................................................................................................... 4 3.1 OVERVIEW ................................................................................................................................... 4 3.2 GENERAL DESCRIPTION ............................................................................................................... 5 3.4 INTELLECTUAL PROPERTY WARNING........................................................................................... 5 3.5 SYSTEM ARCHITECTURE ................................................................................................................... 6 3.6 APPLICATIONS IN DIGITAL SIGNAGE ................................................................................................. 7 3.7 LIST OF ABBREVIATIONS ................................................................................................................... 7 4. INSTALLATION ................................................................................................................................ 8 4.1 FRONT/REAR PANEL INTERFACE ....................................................................................................... 8 4.2 SETTING UP THE MT300 FOR FIRST TIME USE ................................................................................... 9 4.3 USING YOUR PICO BROADCASTER ...................................................................................................15 5. STREAMING .....................................................................................................................................16 5.1 STREAM CONTENT TO DEVICE ..............................................................................................................16 5.2 TUNE THE TV RECEIVER .....................................................................................................................18 6. TROUBLE SHOOTING ...................................................................................................................19 6.1 HARDWARE SETUP ..........................................................................................................................19 6.2 SET UP AND TEST ETHERNET CONNECTION. .....................................................................................19 6.3 TUNING THE TV RECEIVER .............................................................................................................20 Copyright © 2012 by MELD Technology Inc. Information furnished in this document is believed to be accurate and reliable, but MELD assumes no responsibility for any errors that many appear in this material. MT-300 Pico Broadcaster Operator Manual __ 3 1. Preface This document provides operator information on how to set up the MT300 (Ethernet to Broadcast) Pico Broadcaster. This device requires professional installation and the use of tools and procedures for determining location, minimum power requirements. 2. IMPORTANT NOTICES FCC Part 15 Information to the User Caution: Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. Note: This equipment has been tested and found to comply with the rules for TV bands devices, pursuant to part 15 of the FCC rules. These rules are designed to provide reasonable protection against harmful interference. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: (1) Reorient or relocate the receiving antenna. (2) Increase the separation between the equipment and receiver. (3) Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. (4) Consult the manufacturer, dealer or an experienced radio/TV technician for help. RF Exposure The radio described in this manual transmits RF energy. The concentrated energy from the antenna may pose a health hazard. All antennas used with this radio must be installed to provide a minimum separation from all persons of 40 cm (15.7 inches). The above separation distance must be maintained at all times. More information can be obtained from the FCC at the following website: http://www.fcc.gov/Bureaus/Engineering_Technology/Documents/bulletins/oet65/oet65.pdf . MT-300 Pico Broadcaster Operator Manual __ 4 3. Introduction The Meld Technology MT300 White Space radio must be professionally installed by a trained installer. The installation must be in accordance with 47 CFR Part 15 Subpart H and the instructions contained in this manual. Only the following components are approved for use with the radio. Power Supply: Stontronics 3A-401WP12 Antenna: U Tek Technology Co. EA-79X-1 3.1 Overview MELD develops Pico Broadcast products for wirelessly distributing content to any DTV ever made for the North American market using newly op…

Text truncated - open the document above for the full version.

Box Exterior Labels Box SideLabel 6.5 x 5.0 mm Box Top Label On bottom of Device Stick on labelseach 6.5 x 5.0 mm FCC compliance label Product ID label (contains variable data, OEM version would be different) Both would be affixed to underside of device Label Placement Bottom view of device(drawing not exactly to scale)

1 0 6 4 G r e e n w o o d B l v d # 2 0 0 • L a k e M a r y FCC Certification Application Code of Federal Regulations, Title 47, Part 15, Subpart H Applicant: The MT300 is a Fixed TV bands device using a power transmission of a DTV compatible signal over a limited area. only device and the transmitted signal is compliant with the tuner input of a Digital TV It is designed to work with the tuner input of any Di The ID signal is transmitted as an receiver. The FCC ID, location and manufacturer format via the Ethernet port that DTV screen of all DTV receivers tuned to the same channel as the MT300 transmitted signal. The operator will be instructed to than once a day. Detailed instruction 1 0 6 4 G r e e n w o o d B l v d # 2 0 0 • L a k e M a r y • F L • 86 6 . 5 9 8 . 7 4 2 6 spectrumbridge.com FCC Certification Application – Fixed TVBD WhiteSpace Radio FCC ID - OKVMT300 Code of Federal Regulations, Title 47, Part 15, Subpart H Applicant: Meld Technology, Inc. DEVICE ID SIGNAL High Level Description Fixed TV bands device using a VSB modulator that is designed to provide low power transmission of a DTV compatible signal over a limited area. The MT300 is a transmit transmitted signal is compliant with the tuner input of a Digital TV It is designed to work with the tuner input of any Digital TV sold in North America. n ATSC compliant signal that can be received by any The FCC ID, location and manufacturer information is provided in an MPEG2 file format via the Ethernet port that is streamed to the MT300. The text will be displayed on the of all DTV receivers tuned to the same channel as the MT300 transmitted signal. ed to stream the identification information for transmission no less Detailed instructions can be found in the MT300 Operator Manual. 6 6 . 5 9 8 . 7 4 2 6 BD WhiteSpace Radio Code of Federal Regulations, Title 47, Part 15, Subpart H VSB modulator that is designed to provide low- MT300 is a transmit transmitted signal is compliant with the tuner input of a Digital TV receiver. gital TV sold in North America. signal that can be received by any Digital TV in an MPEG2 file The text will be displayed on the of all DTV receivers tuned to the same channel as the MT300 transmitted signal. stream the identification information for transmission no less can be found in the MT300 Operator Manual.

1 0 6 4 G r e e n w o o d B l v d # 2 0 0 • L a k e M a r y • F L • 8 6 6 . 5 9 8. 7 4 2 6 spectrumbridge.com MELD Technology, Inc. 1645 Canary Drive Sunnyvale, CA 94087 Maximum Permissible Exposure Limits MPE Calculations P Transmit Power (mW): 11.57 G Max Antenna Gain (dB): -5 0.316228 Linear Gain R Distance (cm): 1 0.39 inches S Power Density (mW/cm 2 ): -4.606 Limits for General Public (mW/cm 2 ): f = 30 - 300 MHz 0.2 f = 300 - 1500 MHz f/1500 Adjust R until S < limits above Based on FCC OET Bulletin 65

FCC PART 15.Subpart H White Spaces System PART 1TEST REPORT Fixed TVBD Device Part 1 Applicant Meld Technology Inc. Address 1645 Canary Drive Sunnyvale, CA 94087 USA FCC ID OKVMT300 Model Number MT300 Product Description White Space Fixed TVBD Date Sample Received 7/6/2012 Date Tested 7/16/2012 Tested By Sushant Kadimdivan Approved By Mario de Aranzeta Report Number S\SPECTRUM BRIDGE\1695AUT12\1695AUT12TestReport.doc Test Results PASS FAIL THE ATTACHED REPORT SHALL NOT BE REPRODUCED EXCEPT IN FULL WITHOUT THE WRITTEN APPROVAL OF TIMCO ENGINEERING, INC. 849 NW State Road 45 Newberry, FL 32669 USA Ph: 888.472.2424 or 352.472.5500 Fax: 352.472.2030 Email: [email protected] Website: www.timcoengr.com Testing Certificate # 0955-01 APPLICANT: Meld Technology, Inc. FCC ID: OKVMT300 REPORT: s/SPECTRUM BRIDGE/1695AUT12TestReport.doc Page 2 of 40 TABLE OF CONTENT GENERAL REMARKS ...................................................................................................................................... 3 GENERAL INFORMATION .............................................................................................................................. 4 EMC EQUIPMENT LIST ................................................................................................................................... 6 TEST PROCEDURES ........................................................................................................................................ 7 §15.207 & §15.709(C)(5) POWER LINE CONDUCTED INTERFERENCE ............................................................. 8 §15.209 RADIATION INTERFERENCE ............................................................................................................ 11 §15.709(A) POWER LIMITS FIXED TVBD ..................................................................................................... 16 §15.709(A)(3)(I) TRANSMITTER POWER CONTROL FIXED TVBD .................................................................. 19 §15.709(C)(1) EMISSION LIMITS AT THE BAND EDGE FOR TVBDS ............................................................... 20 §15.709(C)(4) EMISSION IN THE BAND OF 602-620MHZ LIMITS FOR TVBDS ............................................... 30 §15.709(D) COMPLIANCE WITH RF EXPOSURE REQUIREMENTS: ................................................................. 38 PRODUCT PHOTOS ...................................................................................................................................... 39 APPLICANT: Meld Technology, Inc. FCC ID: OKVMT300 REPORT: s/SPECTRUM BRIDGE/1695AUT12TestReport.doc Page 3 of 40 GENERAL REMARKS The attached report shall not be reproduced except in full without the written permission of Timco Engineering Inc. The test results relate only to the items tested. Summary The devi…

Text truncated - open the document above for the full version.