OKZ-WC20-2040BTankscan Controller Radio Module

1 TankScan™ W-Series WC2 Controller Installation Manual Version 99L15xz ID#11680 4/2001 Introduction The TankScan Wireless Level System Controller includes a radio/modem enclosure, an antenna, and an AC power adapter. System Installation Steps A. Install Controller (distance & line-of-sight location predetermined). B. Install monitor(s) on the tank(s) C. Install fill indicator(s) at a accessible location near the fill point. D. Install software on host PC E. Power up and configure the Controller F.Power up the monitor(s) and fill unit(s). Controller Installation NOTICE Do not install Controller near any RF sources (TV, Radio, etc.). Interference from such devices can cause data loss and Controller malfunctions. 1. Place Controller on stable flat surface or mount on wall. a. If desired, install the self-adhesive rubber feet. b. To wall mount, attach mounting plate to bottom of enclosure using supplied screws, then attach the assembly to the wall with the antenna connector facing up. Note: Controller must be within reach of the power source/outlet, phone jack (if used) and PC (if direct connection is used). 2. Attach Antenna to Controller (pointed upward). Note: Ant. connector has left-handed thread. 3. Connect Phone Line, using supplied RJ11 cable. Plug one end into the Controller and the other into the wall phone jack. If a phone is needed, plug it into the second RJ11 socket on the Controller. Note: RJ11 sockets are in parallel, either can be used for line. CUS Mounting Bracket See Dimensions on Page 4. RS232 Power Antenna Phone Line CAUTION To reduce the risk of fire, use only No. 28 AWG or larger telecommu- nications line cord. PRELIMINARY 2 Controller Installation (continued) 4. Plug in the appropriate Power Adapter (US or EU type included, per order). Plug the barrel-ended connector into Controller and the 3-prong plug into an unswitched AC outlet. 5. Check front panel indicator lights to make sure unit is operating. During normal operation (with no level requests, fill operations, or modem activities), the power light will be on and the "SYNC" light will flash every 32 seconds. 6. Configure the Controller using the DataScan Plus PC software. 7. The Controller is now ready to receive signals from the level Monitor(s) setup during the DataScan Plus PC software configuration process. (US) Power Adapter (EU) Power Adapter lebaLemaNnoitpircseD RWPrewoPnositinU HOkooHffOkoohffoenilenohP XTataDtimsnarTatadgnidnesmedoM XRataDevieceRatadgniviecermedoM TMXtimsnarToidaRatadgnittimsnartoidaR VCRevieceRoidaRatadgnivieveroidaR CNYScnySemiTdettimsnartgniebegassemcnySemiT QCAedoMeriuqAoidaraivstinudleifgniriuqasirellortnoC The AUTO ANSWER switch sets the modem's answer mode. If OFF, the modem will not answer incoming calls - it will only call out on a pre-set schedule or alarm. Front Panel Indicator Lights & Auto Answer Switch 3 Specifications Operating Temperature ........... +32°F to +140°F (0°C to +60°C) Enclosure ............................... NEMA-1/IP30 - Indoor Use Only Safety Ratings ......................... UL1950, CSA950, and EN60950 Flame Class Rating .................. UL94V-0 Power Requirements ............... 110 VAC (60 Hz) US; 220 VAC (50-60 Hz) Europe, 5 VA Internal Transceiver ................. (for use with up to 30 field devices) Transmits up to 500 feet (150 m), line-of-sight, in the unlicensed 902-928 MHz band (North America) or 869.7-870 MHz band (Europe) Phone Modem ........................ Internal (calls host per schedule or alarm and accepts calls from host) Line Impedance: 600 Ohm, transformer coupled (CTR21 - complex impedance) Dial Type: DTMF or Pulse (subject to national approvals) Baud Rate: 2400 (CCITT V.22bis); 1200 (CCITT V.22 or Bell 212A) Note: This modem will not detect cadenced dial tone, but will blind dial on command. For compliance and approval statements, see pages 5-7. Data Storage .......................... Depends upon number of field devices and frequency of readings. Host Software ........................ Barton DataScan ® Plus PC Software Mounting ............................... Tabletop or wall mount Shipping Weight (approx.) ....... Controller, (standard) Antenna, & AC adapter 1.7 lbs (0.8 kg) Technical Support/Warranty Service/Repair US: 626-961-2547 • Canada: 403-291-4814 • Europe: 441243826741 Symbol Information The following symbols may be used in this manual or on the instrument: 4 Dimensions Replacement Parts List Part DescriptionPart Number AC Power Adapter (US) .......... TL10-2009T Antenna (standard) .................. TL10-2004T Optional Outdoor Antenna (with mount): 20-ft. cable ......................... WC20-2046B-1 30-ft. cable ......................... WC20-2046B-2 Telephone Cable (10') .............. TL10-2007T PC Cable ............................... TS10-1173T 5 COMPLIANCE STATEMENTS FCC COMPLIANCE STATEMENTS FOR WC20 FCC PART 68 NOTICE This equipment complies with FCC Part 68 rules. The FCC registration number and Ringer Equivalent Number (REN) are printed on a label attached to the bottom of the enclosure. You must, upon request, provide this information to your telephone company. The REN number is used to determine the maximum number of devices that may be connected to the phone line and still have all those devices ring when your number is called. To determine the number of devices that may be connected to your line, as determined by the REN, contact your local telephone company. If your telephone equipment causes harm to the telephone network, the telephone company may discontinue your service temporarily. If possible, they will notify you in advance. If advanced notice is not practical, you will be notified as soon as possible. You will be informed of your right to file a complaint with the FCC. If there is a problem with the telephone network, the telephone company may ask you to disconnect your equipment from the telephone line until the problem has been corrected or until it is determined that your equipment is not malf…

Text truncated - open the document above for the full version.

ANTENNA INFORMATION The module was tested using two different antennas, a direct mounted antenna that is attached directly to the module, and a remote mounted antenna that includes a coaxial cable. Both of these antennas are connected to the module using a unique antenna connector (a special TNC connector that uses a left hand thread), which is not available to the general public.

FCC ID: OKZ-WC20-2040B Report No.: B10209D1 114 OLINDA DRIVE, BREA, CALIFORNIA 92823 PHONE: (714) 579-0500 FAX: (714) 579-1850 Page 1 of 18 FCC PART 15, SUBPART B AND C TEST REPORT for TANKSCAN CONTROLLER RADIO MODULE Assembly Number: WC20-2040B Prepared for BARTON INSTRUMENT SYSTEMS, LLC 900 SOUTH TURNBULL CANYON ROAD CITY OF INDUSTRY, CALIFORNIA 91749-1882 COMPATIBLE ELECTRONICS INC. 114 OLINDA DRIVE BREA, CALIFORNIA 92823 (714) 579-0500 DATE: FEBRUARY 12, 2001 REPORT APPENDICES TOTAL BODY A B C D E PAGES 18 2 2 13 28 2 65 This report shall not be reproduced except in full, without the written approval of Compatible Electronics. FCC ID: OKZ-WC20-2040B Report No.: B10209D1 114 OLINDA DRIVE, BREA, CALIFORNIA 92823 PHONE: (714) 579-0500 FAX: (714) 579-1850 Page 2 of 18 TABLE OF CONTENTS Section / Title PAGE GENERAL REPORT SUMMARY 4 SUMMARY OF TEST RESULTS 5 1. PURPOSE 6 2. ADMINISTRATIVE DATA 7 2.1 Location of Testing 7 2.2 Traceability Statement 7 2.3 Cognizant Personnel 7 2.4 Date Test Sample was Received 7 2.5 Disposition of the Test Sample 7 2.6 Abbreviations and Acronyms 7 3. APPLICABLE DOCUMENTS 8 4. Description of Test Configuration 9 4.1 Description of Test Configuration - EMI 9 4.1.1 Cable Construction and Termination 10 5. LISTS OF EUT, ACCESSORIES AND TEST EQUIPMENT 11 5.1 EUT and Accessory List 11 5.2 EMI Test Equipment 12 6. TEST SITE DESCRIPTION 13 6.1 Test Facility Description 13 6.2 EUT Mounting, Bonding and Grounding 13 7. Test Procedures 14 7.1 Radiated Emissions (Spurious and Harmonics) Test 15 7.2 Band Edge Plots of the Low and High Channels 17 8. CONCLUSIONS 18 FCC ID: OKZ-WC20-2040B Report No.: B10209D1 114 OLINDA DRIVE, BREA, CALIFORNIA 92823 PHONE: (714) 579-0500 FAX: (714) 579-1850 Page 3 of 18 LIST OF APPENDICES APPENDIX TITLE A Modifications to the EUT B Additional Models Covered Under This Report C Diagrams, Charts and Photos • Test Setup Diagrams • Radiated Emissions Photos • Antenna and Effective Gain Factors D Data Sheets E Lab Recognitions LIST OF FIGURES FIGURE TITLE 1 Conducted Emissions Test Setup 2 Plot Map And Layout of Test Site FCC ID: OKZ-WC20-2040B Report No.: B10209D1 114 OLINDA DRIVE, BREA, CALIFORNIA 92823 PHONE: (714) 579-0500 FAX: (714) 579-1850 Page 4 of 18 GENERAL REPORT SUMMARY This electromagnetic emission test report is generated by Compatible Electronics Inc., which is an independent testing and consulting firm. The test report is based on testing performed by Compatible Electronics personnel according to the measurement procedures described in the test specifications given below and in the "Test Procedures" section of this report. The measurement data and conclusions appearing herein relate only to the sample tested and this report may not be reproduced in any form unless done so in full with the written permission of Compatible Electronics. This report must not be used to claim product endorsement by NVLAP or any other agency of the U.S. Government. Device Tested: TankScan Controller Radio Module Assembly Number: WC20-2040B S/N: N/A Product Description: See Expository Statement. Modifications: The EUT was not modified during the testing. Manufacturer: Barton Instrument Systems, LLC 900 South Turnbull Canyon Road City of Industry, California 91749-1882 Test Dates: February 7 and 8, 2001 Test Specifications : EMI requirements CFR Title 47, Part 15, Subpart B CFR Title 47, Part 15 Subpart C, Sections 15.205, 15.209, and 15.249 Test Procedure: ANSI C63.4: 1992 Test Deviations: The test procedure was not deviated from during the testing. FCC ID: OKZ-WC20-2040B Report No.: B10209D1 114 OLINDA DRIVE, BREA, CALIFORNIA 92823 PHONE: (714) 579-0500 FAX: (714) 579-1850 Page 5 of 18 SUMMARY OF TEST RESULTS TEST DESCRIPTION RESULTS 1 Conducted RF Emissions, 450 kHz - 30 MHz This test was not performed because the EUT operates on battery power only 2 Radiated RF Emissions for the EUT in transmit mode, 10 kHz - 9300 MHz Complies with the limits of CFR Title 47, Part 15, Subpart C, sections 15.205, 15.209, and 15.249 3 Radiated RF Emissions for the EUT in receive mode, 30 MHz – 5000 MHz Complies with the Class B limits of CFR Title 47, Part 15, Subpart B FCC ID: OKZ-WC20-2040B Report No.: B10209D1 114 OLINDA DRIVE, BREA, CALIFORNIA 92823 PHONE: (714) 579-0500 FAX: (714) 579-1850 Page 6 of 18 1. PURPOSE This document is a qualification test report based on the Electromagnetic Interference (EMI) tests performed on the TankScan Controller Radio Module Assembly Number: WC20- 2040B. The EMI measurements were performed according to the measurement procedure described in ANSI C63.4: 1992. The tests were performed in order to determine whether the electromagnetic emissions from the equipment under test, referred to as EUT hereafter, are within the specification limits defined by CFR Title 47, Part 15, Subpart C, sections 15.205, 15.209, and 15.249. FCC ID: OKZ-WC20-2040B Report No.: B10209D1 114 OLINDA DRIVE, BREA, CALIFORNIA 92823 PHONE: (714) 579-0500 FAX: (714) 579-1850 Page 7 of 18 2. ADMINISTRATIVE DATA 2.1 Location of Testing The EMI tests described herein were performed at the test facility of Compatible Electronics, 114 Olinda Drive, Brea, California 92823. 2.2 Traceability Statement The calibration certificates of all test equipment used during the test are on file at the location of the test. The calibration is traceable to the National Institute of Standards and Technology (NIST) . 2.3 Cognizant Personnel Barton Instrument Systems, LLC Brian Dearden Staff Engineer Compatible Electronics Inc. Kyle Fujimoto Test Engineer Scott McCutchan Lab Manager 2.4 Date Test Sample was Received The test sample was received on February 7, 2001. 2.5 Disposition of the Test Sample The test sample was returned to Barton Instrument Systems, LLC on February 9, 2001. 2.6 Abbreviations and Acronyms The following abbreviations and acronyms may be used in this document. RF Radio Frequency EMI Electromagnetic Interference EUT Equipment Under Test P/N Part Number S/N Serial N…

Text truncated - open the document above for the full version.