Text extracted from the exhibit documents filed with the FCC. Open a document above to read the original.
22611 Markey Ct.; Unit 110; Sterling, VA 20166 (703) 421-2086 08/18/99 PART NO. 72-76060 PERSONAL PROTECTION DEVICE (PPD) INSTRUCTION SHEET Introduction The Dominion Wireless, Inc. personal protection device (PPD) is a body-worn radio transmitter that emits an alert signal when activated. The PPD is intended to be worn on the belt of the user. When used in a facility equipped with the Dominion Wireless, Inc. Personal Alarm Location System (PALS), the transmitter notifies security staff that an alarm transmission has occurred and reports the location of the user on a computerized map of the facility. A unique ID code identifies the particular unit in alarm. The PPD is activated by removing a pull-pin from the end of the PPD housing. Operating Instructions Wearing the PPD Always wear the PPD on the belt in a location that permits easy access to the pull-pin. It is recommended that the unit be used with the optional carrying pouch for added protection. The PPD can also be worn on the belt with the included belt clip. Always position the belt clip (also the battery cover) surface towards the body for optimal performance. The performance of the unit is not degraded if worn under clothing. Activation The PPD is activated by completely removing the pull-pin. The unit transmits its unique ID code once each time the pin is removed. It takes approximately one quarter (.25) of a second for the transmitter to complete the alarm sequence once the pull-pin is removed. Your ID and position will be reported to security staff within three seconds of activation. RE-INSERTING THE PULL-PIN DOES NOT PREVENT THE TRANSMITTER FROM SENDING THE ALERT SIGNAL. Always return the pull-pin to its mating plug in the PPD housing so that the unit is armed and to prevent the pull-pin from becoming lost. The pull-pin is equipped with a flexible lanyard to make activation easier. Do not cover the PPD with your hand when activating – simply remove the pull-pin. Testing Test the PPD at the beginning of each shift. Your facility administrator will develop a procedure for you to warn the security staff that a test transmission is under way and for the security staff to communicate to you that the unit has passed the test. Follow their established procedures. Since the PPD is a battery-operated device, it is imperative that you test its operation at the beginning of each shift. The internal battery will operate reliably for one year when activated three times per day (once each, at the beginning of three shifts). The battery must be replaced once every twelve months. If the battery is operational at the beginning of your shift, but begins to discharge below its operating threshold during your shift, the unit will automatically transmit a low battery alert to the central computer. This will instruct the security staff to contact you and have your PPD replaced. DO NOT ATTEMPT TO REPLACE THE BATTERY YOURSELF. THIS PROCEDURE IS INTENDED FOR TRAINED FACILITY MAINTENANCE STAFF. 22611 Markey Ct.; Unit 110; Sterling, VA 20166 (703) 421-2086 08/18/99 Do’s & Don’ts Do Always wear the PPD on your belt. Always position the PPD on your belt such that the pull-pin is accessible. Always wear the transmitter with the battery cover and belt clip (if used) towards your body. If your PPD fails to transmit upon activation, return the unit to maintenance immediately. If you accidentally remove the pull-pin, contact security immediately to report the false alarm. Don’t: Submerge the PPD in water or expose it to pounding rain. Cover the unit with your hand or metal objects while transmitting. Wear or store the PPD without the pull-pin completely inserted . Replace batteries unless you are a certified maintenance technician. Remove the marking labels on the transmitter. Drop or otherwise abuse the transmitter. Operator Maintenance and Cleaning There are no operator-servicable components or adjustments on the PPD. If the unit becomes soiled, wipe with a damp (not dripping) cloth or paper towel. Do not use other solvents or cleaning agents on the transmitter housing. If the carrying pouch becomes saturated with moisture, obtain a new pouch since this can potentially impact locating accuracy. Accessories Dominion Wireless, Inc. PPD Carrying Pouch Pull pin & cord Specifications Personal Alarm Transmitter Operating Frequency:420-475 MHz Frequency Stability:+/- 1 2KHz over temperature, voltage, all loads Output Power:50 mW, +/- 1dB over temperature and voltage Modulation:FM, FSK Antenna:Integral, no external antenna Operating Temperature:-20 to +55 Deg. C Operating Humidity:0 to 90% Noncondensing Dimensions:2.3” x 4.2” x .75” Battery:Duracell # PX28L / Eveready #L544 Battery Life:1 Year, 3 activations per day Weight (including battery):4 oz.
Dominion Wireless, Inc 22611 Markey Ct., Unit 110 Sterling, VA 20166 September 24, 1999 Federal Communications Commission Washington, DC Subject:FCC Application, Dominion Wireless, Inc. Transmitter Part Number B76060, Request for Proprietary Application To Whom it May Concern: Dominion Wireless requests that the subject application and all related filings be kept proprietary and is providing a $135 payment as due consideration. The following technical information about the transmitter is deemed company proprietary: Operating Specifications Block Diagram Schematic Diagram Printed Circuit Board Top Assembly Synthesizer and Power Output Control Design Modulation Waveform Generation Design Microprocessor Firmware Feel free to contact me at (703)-421-2086 if you have an questions regarding the technical material referenced above. Sincerely, Roger Christ President, Dominion Wireless, Inc.
Dominion Wireless, Inc 22611 Markey Ct., Unit 110 Sterling, VA 20166 September 24, 1999 Federal Communications Commission Washington, DC Subject:FCC Application, Dominion Wireless, Inc. Transmitter Part Number B76060, Request for Proprietary Application To Whom it May Concern: Dominion Wireless requests that the subject application and all related filings be kept proprietary and is providing a $135 payment as due consideration. The following technical information about the transmitter is deemed company proprietary: 1. Appendix H: Personal Alarm Transmitter Design Specification • Operating Specifications • Synthesizer and Power Output Control Design • Modulation Waveform Generation Design • Microprocessor Firmware 2. Block Diagram 3. Schematic Diagram Feel free to contact me at (703)-421-2086 if you have an questions regarding the technical material referenced above. Sincerely, Roger Christ President, Dominion Wireless, Inc.
APPENDIX G: LABEL INFORMATION Please see following pages. G1: FCC ID LABEL G2: LOCATION OF LABEL ON EUT Label Placement FCC ID: OQUB76060
APPENDIX B: PRODUCT DESCRIPTION Please see following pages. B1: PRODUCT DESCRIPTION OVERVIEW The Dominion Wireless, Inc. Personal Protection Device (PPD) is a body worn radio transmitter that emits an alert signal when activated the PPD is intended to be worn on the belt of the user. When used in a facility equipped with the Dominion Wireless, Inc. Personal Alarm Location System (PALS), the transmitter notifies security staff that an alarm transmission has occurred and reports the location of the user on a computerized map of the facility. A unique ID code identifies the particular unit in alarm. Removing a pull-pin from the end of the PPD housing activates the PPD. For more detailed information please refer to the “Personal Alarm Transmitter Design Specification”.
APPENDIX D: PLOTS Please see following pages. D1: CHANNEL 421 AT 10 KHZ D2: CHANNEL 421 AT 100 HZ D3: CHANNEL 458.9375 AT 10 KHZ D4: CHANNEL 458.9375 AT 100 HZ D5: CHANNEL 470 AT 10 KHZ D6: CHANNEL 470 AT 100 HZ D7: 421 MHZ SPURIOUS D8: 458 MHZ SPURIOUS D9: 470 MHZ SPURIOUS D10: 421 BANDWIDTH D11: 458 BANDWIDTH D12: 470 BANDWIDTH
ÕÕÕÕÕÕÕÕÕÕÕÕÕÕÕÕÕÕÕÕÕÕÕÕÕÕÕÕÕÕÕÕÕÕÕÕÕÕÕÕÕÕÕÕÕÕÕ APPLICATION FOR PART 90 TYPE CERTIFICATION TRANSMITTER Dominion Wireless Inc. 22611 Markey Ct, Unit 110 Sterling, VA 20166 MODEL: Personal Protection Device (PPD) FCC ID: OQUB76060 October 8, 1999 REPORT PREPARED BY: EMI Technician:Daniel Baltzell Administrative Writer:Melissa Fleming Rhein Tech Laboratories, Inc. Document Number: 990386 / QRTL99-147A No part of this report may be reproduced without the full written approval of Rhein Tech Laboratories, Inc. This report concerns (check one):Original Grant: X Class II Change: Equipment Type: Transmitter Deferred grant requested per 47 CFR 0.457 (d) (1) (ii)?Yes:No: X If yes, defer until: Date Company name agrees to notify the Commission by: (date) of the intended date of announcement of the product so that the grant can be issued on that date. FCC ID: OQUB76060 i TABLE OF CONTENTS 1.0GENERAL INFORMATION...................................................................................................................1 1.1TEST METHODOLOGY..............................................................................................................................1 1.2TEST FACILITY........................................................................................................................................1 1.3JUSTIFICATION.........................................................................................................................................2 1.4EUT EXERCISE SOFTWARE.......................................................................................................................2 1.5SPECIAL ACCESSORIES.............................................................................................................................2 1.6CONFORMANCE STATEMENT....................................................................................................................3 2.0STANDARD REQUIREMENTS.............................................................................................................4 2.1FCC PART 90.217(B): EXEMPTION FROM TECHNICAL STANDARDS...........................................................4 2.2FCC PART PART 2.1047(D): MODULATION REQUIREMENTS AND CHARACTERISTICS...................................4 2.3FCC PART 2.1046: RF OUTPUT POWER...................................................................................................4 2.3.1 Methods of Measurement and Test Results.............................................................................................4 2.4FCC PART 2.1049 AND ANSI C63.4, SECTION 13.1.7: OCCUPIED BANDWIDTH.........................................6 2.5FCC PART 2.1057(A)(1): FREQUENCY SPECTRUM TO BE INVESTIGATED.....................................................6 2.6FCC PART 2.1051 AND PART 90.217(A): SPURIOUS EMISSIONS AT ANTENNA TERMINALS..........................6 2.6.1 Method of measurement:.......................................................................................................................6 2.7FCC PART 2.993 AND PART 90.217(A): FIELD STRENGTH OF SPURIOUS RADIATION..................................7 2.7.1Method of measurement:.................................................................................................................7 2.8FCC PART 90.213 AND PART 2.995(A): FREQUENCY STABILITY FUNCTION OF TEMPERATURE....................7 2.8.1 Method of Measurement:.......................................................................................................................7 2.8.2 Test Results:..........................................................................................................................................7 3.0SYSTEM TEST CONFIGURATION......................................................................................................8 3.1RELATED SUBMITTAL(S)/GRANT(S)..........................................................................................................8 3.2TEST SYSTEM DETAILS............................................................................................................................8 4.0TEST RESULTS.......................................................................................................................................9 4.1FIELD STRENTH OF SPURIOUS RADIATION.................................................................................................9 5.0 FIELD STRENGTH CALCULATION, AND RADIATED TEST METHODOLOGY............................10 5.1FIELD STRENGTH CALCULATION.............................................................................................................10 5.2RADIATED MEASUREMENT......................................................................................................................11 FCC ID: OQUB76060 ii APPENDIX LISTING APPENDIX A: EQUIPMENT LIST...................................................................................................................12 APPENDIX B: PRODUCT DESCRIPTION....................................................ERROR! BOOKMARK NOT DEFINED. B1: PRODUCT DESCRIPTION OVERVIEW.............................................................ERROR! BOOKMARK NOT DEFINED. APPENDIX C: TEST PICTURES...................................................................ERROR! BOOKMARK NOT DEFINED. C1: RADIATED TEST PICTURES FRONT VIEW......................................................ERROR! BOOKMARK NOT DEFINED. C2: RADIATED TEST PICTURES REAR VIEW........................................................ERROR! BOOKMARK NOT DEFINED. APPENDIX D: PLOTS...................................................................................ERROR! BOOKMARK NOT DEFINED. D1: CHANNEL 421 AT 10 KHZ.........................................................................ERROR! BOOKMARK NOT DEFINED. D2: CHANNEL 421 AT 100 HZ.........................................................................ERROR! BOOKMARK NOT DEFINED. D3: CHANNEL 458.9375 AT 10 KHZ..................…
Text truncated - open the document above for the full version.
ÕÕÕÕÕÕÕÕÕÕÕÕÕÕÕÕÕÕÕÕÕÕÕÕÕÕÕÕÕÕÕÕÕÕÕÕÕÕÕÕÕÕÕÕÕÕÕ APPLICATION FOR PART 90 TYPE CERTIFICATION TRANSMITTER Dominion Wireless Inc. 22611 Markey Ct, Unit 110 Sterling, VA 20166 MODEL: Personal Protection Device (PPD) FCC ID: OQUB76060 October 8, 1999 REPORT PREPARED BY: EMI Technician:Daniel Baltzell Administrative Writer:Melissa Fleming Rhein Tech Laboratories, Inc. Document Number: 990386 / QRTL99-147A No part of this report may be reproduced without the full written approval of Rhein Tech Laboratories, Inc. This report concerns (check one):Original Grant: X Class II Change: Equipment Type: Transmitter Deferred grant requested per 47 CFR 0.457 (d) (1) (ii)?Yes:No: X If yes, defer until: Date Company name agrees to notify the Commission by: (date) of the intended date of announcement of the product so that the grant can be issued on that date. FCC ID: OQUB76060 i TABLE OF CONTENTS 1.0GENERAL INFORMATION...................................................................................................................1 1.1TEST METHODOLOGY..............................................................................................................................1 1.2TEST FACILITY........................................................................................................................................1 1.3JUSTIFICATION.........................................................................................................................................2 1.4EUT EXERCISE SOFTWARE.......................................................................................................................2 1.5SPECIAL ACCESSORIES.............................................................................................................................2 1.6CONFORMANCE STATEMENT....................................................................................................................3 2.0STANDARD REQUIREMENTS.............................................................................................................4 2.1FCC PART 90.217(B): EXEMPTION FROM TECHNICAL STANDARDS...........................................................4 2.2FCC PART PART 2.1047(D): MODULATION REQUIREMENTS AND CHARACTERISTICS...................................4 2.3FCC PART 2.1046: RF OUTPUT POWER...................................................................................................4 2.3.1 Methods of Measurement and Test Results.............................................................................................4 2.4FCC PART 2.1049 AND ANSI C63.4, SECTION 13.1.7: OCCUPIED BANDWIDTH.........................................6 2.5FCC PART 2.1057(A)(1): FREQUENCY SPECTRUM TO BE INVESTIGATED.....................................................6 2.6FCC PART 2.1051 AND PART 90.217(A): SPURIOUS EMISSIONS AT ANTENNA TERMINALS..........................6 2.6.1 Method of measurement:.......................................................................................................................6 2.7FCC PART 2.993 AND PART 90.217(A): FIELD STRENGTH OF SPURIOUS RADIATION..................................7 2.7.1Method of measurement:.................................................................................................................7 2.8FCC PART 90.213 AND PART 2.995(A): FREQUENCY STABILITY FUNCTION OF TEMPERATURE....................7 2.8.1 Method of Measurement:.......................................................................................................................7 2.8.2 Test Results:..........................................................................................................................................7 3.0SYSTEM TEST CONFIGURATION......................................................................................................8 3.1RELATED SUBMITTAL(S)/GRANT(S)..........................................................................................................8 3.2TEST SYSTEM DETAILS............................................................................................................................8 4.0TEST RESULTS.......................................................................................................................................9 4.1FIELD STRENTH OF SPURIOUS RADIATION.................................................................................................9 5.0 FIELD STRENGTH CALCULATION, AND RADIATED TEST METHODOLOGY............................10 5.1FIELD STRENGTH CALCULATION.............................................................................................................10 5.2RADIATED MEASUREMENT......................................................................................................................11 FCC ID: OQUB76060 ii APPENDIX LISTING APPENDIX A: EQUIPMENT LIST...................................................................................................................12 APPENDIX B: PRODUCT DESCRIPTION....................................................ERROR! BOOKMARK NOT DEFINED. B1: PRODUCT DESCRIPTION OVERVIEW.............................................................ERROR! BOOKMARK NOT DEFINED. APPENDIX C: TEST PICTURES...................................................................ERROR! BOOKMARK NOT DEFINED. C1: RADIATED TEST PICTURES FRONT VIEW......................................................ERROR! BOOKMARK NOT DEFINED. C2: RADIATED TEST PICTURES REAR VIEW........................................................ERROR! BOOKMARK NOT DEFINED. APPENDIX D: PLOTS...................................................................................ERROR! BOOKMARK NOT DEFINED. D1: CHANNEL 421 AT 10 KHZ.........................................................................ERROR! BOOKMARK NOT DEFINED. D2: CHANNEL 421 AT 100 HZ.........................................................................ERROR! BOOKMARK NOT DEFINED. D3: CHANNEL 458.9375 AT 10 KHZ..................…
Text truncated - open the document above for the full version.
APPENDIX D: PLOTS Please see following pages. D1: CHANNEL 421 AT 10 KHZ D2: CHANNEL 421 AT 100 HZ D3: CHANNEL 458.9375 AT 10 KHZ D4: CHANNEL 458.9375 AT 100 HZ D5: CHANNEL 470 AT 10 KHZ D6: CHANNEL 470 AT 100 HZ D7: 421 MHZ SPURIOUS D8: 458 MHZ SPURIOUS D9: 470 MHZ SPURIOUS D10: 421 BANDWIDTH D11: 458 BANDWIDTH D12: 470 BANDWIDTH
ÕÕÕÕÕÕÕÕÕÕÕÕÕÕÕÕÕÕÕÕÕÕÕÕÕÕÕÕÕÕÕÕÕÕÕÕÕÕÕÕÕÕÕÕÕÕÕ APPLICATION FOR PART 90 TYPE CERTIFICATION TRANSMITTER Dominion Wireless Inc. 22611 Markey Ct, Unit 110 Sterling, VA 20166 MODEL: Personal Protection Device (PPD) FCC ID: OQUB76060 October 8, 1999 REPORT PREPARED BY: EMI Technician:Daniel Baltzell Administrative Writer:Melissa Fleming Rhein Tech Laboratories, Inc. Document Number: 990386 / QRTL99-147A No part of this report may be reproduced without the full written approval of Rhein Tech Laboratories, Inc. This report concerns (check one):Original Grant: X Class II Change: Equipment Type: Transmitter Deferred grant requested per 47 CFR 0.457 (d) (1) (ii)?Yes:No: X If yes, defer until: Date Company name agrees to notify the Commission by: (date) of the intended date of announcement of the product so that the grant can be issued on that date. FCC ID: OQUB76060 i TABLE OF CONTENTS 1.0GENERAL INFORMATION...................................................................................................................1 1.1TEST METHODOLOGY..............................................................................................................................1 1.2TEST FACILITY........................................................................................................................................1 1.3JUSTIFICATION.........................................................................................................................................2 1.4EUT EXERCISE SOFTWARE.......................................................................................................................2 1.5SPECIAL ACCESSORIES.............................................................................................................................2 1.6CONFORMANCE STATEMENT....................................................................................................................3 2.0STANDARD REQUIREMENTS.............................................................................................................4 2.1FCC PART 90.217(B): EXEMPTION FROM TECHNICAL STANDARDS...........................................................4 2.2FCC PART PART 2.1047(D): MODULATION REQUIREMENTS AND CHARACTERISTICS...................................4 2.3FCC PART 2.1046: RF OUTPUT POWER...................................................................................................4 2.3.1 Methods of Measurement and Test Results.............................................................................................4 2.4FCC PART 2.1049 AND ANSI C63.4, SECTION 13.1.7: OCCUPIED BANDWIDTH.........................................6 2.5FCC PART 2.1057(A)(1): FREQUENCY SPECTRUM TO BE INVESTIGATED.....................................................6 2.6FCC PART 2.1051 AND PART 90.217(A): SPURIOUS EMISSIONS AT ANTENNA TERMINALS..........................6 2.6.1 Method of measurement:.......................................................................................................................6 2.7FCC PART 2.993 AND PART 90.217(A): FIELD STRENGTH OF SPURIOUS RADIATION..................................7 2.7.1Method of measurement:.................................................................................................................7 2.8FCC PART 90.213 AND PART 2.995(A): FREQUENCY STABILITY FUNCTION OF TEMPERATURE....................7 2.8.1 Method of Measurement:.......................................................................................................................7 2.8.2 Test Results:..........................................................................................................................................7 3.0SYSTEM TEST CONFIGURATION......................................................................................................8 3.1RELATED SUBMITTAL(S)/GRANT(S)..........................................................................................................8 3.2TEST SYSTEM DETAILS............................................................................................................................8 4.0TEST RESULTS.......................................................................................................................................9 4.1FIELD STRENTH OF SPURIOUS RADIATION.................................................................................................9 5.0 FIELD STRENGTH CALCULATION, AND RADIATED TEST METHODOLOGY............................10 5.1FIELD STRENGTH CALCULATION.............................................................................................................10 5.2RADIATED MEASUREMENT......................................................................................................................11 FCC ID: OQUB76060 ii APPENDIX LISTING APPENDIX A: EQUIPMENT LIST...................................................................................................................12 APPENDIX B: PRODUCT DESCRIPTION....................................................ERROR! BOOKMARK NOT DEFINED. B1: PRODUCT DESCRIPTION OVERVIEW.............................................................ERROR! BOOKMARK NOT DEFINED. APPENDIX C: TEST PICTURES...................................................................ERROR! BOOKMARK NOT DEFINED. C1: RADIATED TEST PICTURES FRONT VIEW......................................................ERROR! BOOKMARK NOT DEFINED. C2: RADIATED TEST PICTURES REAR VIEW........................................................ERROR! BOOKMARK NOT DEFINED. APPENDIX D: PLOTS...................................................................................ERROR! BOOKMARK NOT DEFINED. D1: CHANNEL 421 AT 10 KHZ.........................................................................ERROR! BOOKMARK NOT DEFINED. D2: CHANNEL 421 AT 100 HZ.........................................................................ERROR! BOOKMARK NOT DEFINED. D3: CHANNEL 458.9375 AT 10 KHZ..................…
Text truncated - open the document above for the full version.
APPENDIX C: TEST PICTURES Please see following pages. C1: RADIATED TEST PICTURES FRONT VIEW C2: RADIATED TEST PICTURES REAR VIEW
360 Herndon Parkway · Herndon, Virginia · United States
| # | Rule Parts | Frequency Range | Power Output | Emission | Tolerance |
|---|---|---|---|---|---|
| 1 | 90.217(b) | 421 MHz - 470 MHz | 92.70 mW | 25K0F7D | 1010.0000000000 Hz |