OWFWSWireless Thermometer with Clock WS

G G G G G G G G G G G

FCC ID: OWFWS ——————————————————————————————————————————————— Advanced Compliance Lab, 6 Randolph Way, Hillsborough, NJ 08844 Tel: (908) 927 9288 Fax: (908) 927 0728 16 Figure 6.1 Front View FCC ID: OWFWS ——————————————————————————————————————————————— Advanced Compliance Lab, 6 Randolph Way, Hillsborough, NJ 08844 Tel: (908) 927 9288 Fax: (908) 927 0728 17 Figure 6.2 Rear View

FCC ID: OWFWS ——————————————————————————————————————————————— Advanced Compliance Lab, 6 Randolph Way, Hillsborough, NJ 08844 Tel: (908) 927 9288 Fax: (908) 927 0728 8 2. PRODUCT LABELING Fig 2.1 FCC Label ( statement may be shown in user manual) Fig 2.2 Location of the Label FCC Label FCC ID: OWFWS This device complies with part 15 of the FCC Rules. Operatin g is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept an y interference received, including interference that may causeundesired operation.

FCC ID: OWFWS ——————————————————————————————————————————————— Advanced Compliance Lab, 6 Randolph Way, Hillsborough, NJ 08844 Tel: (908) 927 9288 Fax: (908) 927 0728 18 Figure 6.3 Open View FCC ID: OWFWS ——————————————————————————————————————————————— Advanced Compliance Lab, 6 Randolph Way, Hillsborough, NJ 08844 Tel: (908) 927 9288 Fax: (908) 927 0728 19 Figure 6.4 Component Side FCC ID: OWFWS ——————————————————————————————————————————————— Advanced Compliance Lab, 6 Randolph Way, Hillsborough, NJ 08844 Tel: (908) 927 9288 Fax: (908) 927 0728 20 Figure 6.5 Foil Side

Operational description of RX Main unit 1. The Jumbo thermo clock main unit is MCU based LCD clock. 2. U1 MCU is clocked by a 32.768KHz crystal. 3. Battery low detection circuitry de tects battery low level of battery. 4. Thermo sensor is connected to MCU to measure the indoor temperature. 5. Buzzer circuitry is the output stage for alarm and keystone. 6. RCC RX circuitry is a receiver to captu re and amplify the RCC signal. A formed time data is fed to MCU every 1 hour. 7. 433MHz RX circuitry is RF receiver to receive the outdoor temperature signa l form the transmitter. Operational description of TX : 1. MCU generates a sequenced c ode to fed the RF transmitter. 2. Battery low detection circuitry de tects battery low level of battery. 3. A SAW resonator works in 433MHZ TX transmitter to transmit the outdoor temperatur e signal to main unit. 4. Thermo sensor is connected to MCU to detector the outdoor temperature.

ELECTROMAGNETIC EMISSION COMPLIANCE REPORT of Wireless Thermometer With Clock MODEL: WS FCC ID: OWFWS March 8, 2006 This report concerns (check one): Original grant X Class II change Equipment type: TRANSMITTER Deferred grant requested per 47 CF 0.457(d)(1)(ii)? yes no x If yes, defer until: (date) Company agrees to notify the Commission by (date) of the intended date of announcement of the product so that the grant can be issued on that date. Transition Rules Request per 15.37? yes no x If no, assumed Part 15, Subpart B for unintentional radiators - the new 47 CFR [10-1-90 Edition] provision. Report prepared for: KNOW-HOW DEVELOPMENT LIMITED Report prepared by: Advanced Compliance Lab Report number: 0048-060228-01 The test result in this report IS supported and covered by the NVLAP accreditation 6 Randolph Way Hillsborough, NJ 08844 Tel: (908) 927 9288 Fax: (908) 927 0728 Advanced Com pliance Laboratory FCC ID: OWFWS ——————————————————————————————————————————————— Advanced Compliance Lab, 6 Randolph Way, Hillsborough, NJ 08844 Tel: (908) 927 9288 Fax: (908) 927 0728 2 Table of Contents Report Cover Page .........................................................................................................1 Table of Contents ...........................................................................................................2 Figures.............................................................................................................................3 1. GENERAL INFORMATION ...................................................................................4 1.1 Verification of Compliance .........................................................................4 1.2 Equipment Modifications............................................................................5 1.3 Product Information....................................................................................6 1.4 Test Methodology.........................................................................................6 1.5 Test Facility ..................................................................................................6 1.6 Test Equipment ............................................................................................6 1.7 Statement of the Document Use..................................................................7 2. PRODUCT LABELING............................................................................................8 3. SYSTEM TEST CONFIGURATION ......................................................................9 3.1 Justification ..................................................................................................9 3.2 Special Accessories.......................................................................................9 3.3 Configuration of Tested System .................................................................9 4. SYSTEM SCHEMATICS .........................................................................................11 5. RADIATED EMISSION DATA ...............................................................................12 5.1 Field Strength Calculation ..........................................................................12 5.2 Test Methods and Conditions .....................................................................12 5.3 Test Data .......................................................................................................12 5.4 Occupied Bandwidth ...................................................................................14 6. PHOTOS OF TESTED EUT ....................................................................................15 FCC ID: OWFWS ——————————————————————————————————————————————— Advanced Compliance Lab, 6 Randolph Way, Hillsborough, NJ 08844 Tel: (908) 927 9288 Fax: (908) 927 0728 3 Figures Figure 2.1 FCC ID Label...............................................................................................8 Figure 2.2 Location of Label on Bottom of the EUT ..................................................8 Figure 3.1 Radiated Test Setup Front..........................................................................10 Figure 4.1 EUT Schematics ...........................................................................................11 Figure 5.1 Occupied Bandwidth ...................................................................................14 Figure 6.1 Front View....................................................................................................16 Figure 6.2 Rear View .....................................................................................................17 Figure 6.3 Open View ....................................................................................................18 Figure 6.4 Component Side ...........................................................................................19 Figure 6.5 Foil Side ........................................................................................................20 FCC ID: OWFWS ——————————————————————————————————————————————— Advanced Compliance Lab, 6 Randolph Way, Hillsborough, NJ 08844 Tel: (908) 927 9288 Fax: (908) 927 0728 4 1. GENERAL INFORMATION 1.1 Verification of Compliance EUT: Wireless Thermometer with Clock (TX) Model: WS Applicant: KNOW-HOW DEVELOPMENT LIMITED Test Type: FCC Part 15C CERTIFICATION Result: PASS Tested by: ADVANCED COMPLIANCE LAB Test Date: March 7, 2005 Report Number: 0048-060228-01 The above equipment was tested by Advanced Compliance Laboratory for compliance with the requirement set forth in the FCC rules and regulations Part 15, subpart C. This said equipment in the configuration described in the report, shows the maximum emission levels emanating from equipment are within the compliance requirements. The estimated uncertainty of the test result is given as following. The method of uncertainty calculation is provided in Advanced Compliance Lab. Doc. No. 0048-01-01. P…

Text truncated - open the document above for the full version.

FCC ID: OWFWS ——————————————————————————————————————————————— Advanced Compliance Lab, 6 Randolph Way, Hillsborough, NJ 08844 Tel: (908) 927 9288 Fax: (908) 927 0728 10 Figure 3.1 Radiated Test Setup, Front