OWLA99Android POS Terminal

6 Flash light ⑫ Docking interface ⑬ Power key ⑭ NANO SIM slots ⑮ *SD card slots ⑯ SAM card slots ⑰ SIM2 slots ⑱ IC card reader ⑲ Rear Cameras ⑪ Take out the POS terminal, lithium battery, the power adapter, and other necessary parts from the packing box, then follow the steps below for a quick installation. 1 Install the printing paper： ① Pull up the printing paper container cover to open the container. ② Strip off the printing paper. Hold one side of the paper and put it into the container. Leave a bit of the paper on the top of the scudding knife. ③ Close the cover when hearing the "tick" sound. 【 Cautions】 Please be careful with the direction when installing the thermal printing paper, and please do so by following the figures below,otherwise it will cause a failure of printing. 3 Install and remove the lithium battery: Install the battery: Open the battery cover Insert the plug side of the battery into the battery socket Put the battery into the battery container; Close the battery cover. Remove the battery: Open the battery cover after power-off; Pull off the battery by grasping the line at the plug and pulling it up and off ; Gently remove the battery from the battery container. Power on / Power off / Restart: • Power on: press and hold the “Power” key on the keyboard for 2 seconds. When the backlight of the display scree is on, the device is activating. • Power off/ Restart: press and hold the “Power” key for 2 seconds. The screen will display options for "shutdown/con- textual model/restart/airplane mode" menu. Press the “shutdown” key to complete the shutdown; Press the “restart” key to restart the device. [Cautions] When operating a transaction, the user interface is in the communi- cation status. Please do not turn off your device. 5 7 Usage and Operation Quick Operation Guide A99 Android POS Terminal The pictures and descriptions in this guide are for reference only, please prevaillin in kind. Statement Product Description Quick installation Package Content Please read this guide carefully before using the device to ensure your safety and correct use of the device. For information about the device configuration, please refer to the contract or information related to the device and the seller of the device to you. The pictures in this guide are for reference only. If some pictures do not match the actual products, please refer to the actual products. Many network functions described in this document are special services provided by network service providers (ISPs). The availability of these network functions depends on the ISPs that provide the services to you. No part of this Manual shall be reproduced, excerpted, backed up, modified, transmitted, translated into other languages, or used in whole or in part for commercial purposes in any form or by any means without the permis- sion of the Company. Components Name 8 1. The battery is exhausted and cannot be recharged. Please change the battery. 2. The battery volume is low. Please recharge the battery. Failing to turn on the device when pressing the power key Display screen shows error massage about network or service Touch screen slow or incorrect reaction Device is frozen or has serious mistakes If the device is frozen or suspended, it may need to be shutdown or restarted to re-motivate functions. If the device is frozen or has slow reaction, please press the power key for 6 seconds, and the device will be restarted automatically. 1. The device may lost the ability of receiving signal when you are in a place where the signal is weak or reception is bad. Please try to relocate and try it again. 2. Some of the options may not be able to use because of the lack of reservation. Please contact your service providers for more information. If the device has a touch screen, and the screen reaction is incorrect, please try with the following options: 1. Take off the protective film on the screen because it may prevent the device recognize input correctly. We do not recommend to use any type of protective films for touch screens. 2. Please ensure that the screen is clean without greasy dirt. Please keep fingers dry and clean when touching the screen. 3. Please restart the device to solve any type of temporary software errors. 4. If the screen is scratched or damaged, please contact the agent or distributor selling the device to you. Troubles and Troubleshooting TroublesTroubleshooting A99 Android POS terminal Lithium battery Power adapter USB cable Quick operation guide Certificate of qualification and Warranty card Quantity -10- Matters need attention Cautions for use Unauthorized disassembly of this device will cause the built-in security key to be destroyed resulting in unusable. If the power adapter plug or power cord is damaged, please do not use them in case of electric shock or fire. Please do not touch power cord with wet hand or pull out the power adapter like pulling power cable. Please do not touch the device and power adapter with wet hand in case of short circuit, malfunction, or electric shock. Please stop using the power adapter and contact sales representatives for exchanging if the power adapter is caught in the rain, getting wet, or affected with damp seriously. The charge must be certified by local regulations and meet the charging specifications of the device. If the device has to connect USB ports, please ensure that the USB ports has USB-IF identification, and its performance is qualified with the USB-IF requirements. Operating environment Do not use the device during thunderstorms. Otherwise, the device may fail or you could get an electric shock. Avoid putting the terminal in direct sunlight high temperature, moist, or dusty environment Forbid non-professional to repair the terminal. Before insert the card, please check internal and around of IC card slot when you found some suspicious objects, must report to related administra- tor. A door or cover intended only for occasional use by the ordinary person such …

Text truncated - open the document above for the full version.

Applicant Declaration QSF27-14-04 Rev 1.0 Rev. Feb 6, 2023 Page 1 of 1 Original Issue: Jan. 4, 2021 SGS North America Inc. 620 Old Peachtree Road SUITE 100 Suwanee, Georgia 30024 United States Applicant Legal Business Name Vanstone Electronic (Beijing) Co., Ltd. Address 3F No.2 Building, Aisino corporation park 18A, Xingshikou Road, Haidian District, Beijing, China Grantee Code OWL FCC ID OWLA99 Authorized Contact Name ZhiQin Shan Contact Email [email protected] Contact Phone 86-10-88048100 I, the undersigned, certify that I am an authorized signatory for the Applicant and therefore declare; a) in accordance with 47CFR2.911(d), all of the statements herein and the exhibits attached hereto are true and correct to the best of my knowledge and belief. b) in accepting a Grant of Equipment Authorization issued by a TCB, under the authority of the FCC, as a result of the representations made in this application, the Applicant is responsible for: (1) labeling the equipment with the exact FCC ID as specified in this application, (2) compliance statement labeling pursuant to the applicable rules, (3) compliance of the equipment with the applicable technical rules, c) if the Applicant is not the actual manufacturer of the equipment, appropriate arrangements have been made with the manufacturer to ensure that production units of this equipment will continue to comply with the FCC’s technical requirements. d) in accordance with 47 CFR 2.909 and KDB394321, the Applicant has read, understood and agrees to accept that they are the responsible party and agree to abide by their responsibilities as specified under 47 CFR 2.909 and KDB394321. e) in accordance with ISO 17065, FCC KDB641163, FCC KDB610077, KDB394321 and RSP-100, the Applicant has read, understood, accepts and agrees to abide by the post market surveillance requirements. (1) the Applicant understands, accepts and agrees that a sample may be requested for surveillance testing. (2) the Applicant shall make provisions to always have a production sample available upon request by SGS, FCC and/or ISED. (3) the Applicant shall, upon request by SGS, at the Applicant’s expense, provide a production sample of the requested product to SGS, FCC and/or ISED as instructed. The sample shall include all support devices, cables, software, accessories or other hardware or software required for evaluation, review, certification and audit surveillance of products certified by SGS. f) neither the Applicant nor any party to the application is subject to a denial of Federal benefits, that includes FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C. §862 because of a conviction for possession or distribution of a controlled substance. See 47CFR 1.2002(b) for the definition of a “party” for these purposes. g) the Applicant has read, understood, accepts and agrees to abide by the SGS North America, Inc.(TCB) terms and conditions. Link to CFRs: https://www.fcc.gov/wireless/bureau-divisions/technologies-systems-and-innovation-division/rules-regulations-title-47 Link to KDBs: https://apps.fcc.gov/oetcf/kdb/index.cfm Link to RSP-100: https://www.ic.gc.ca/eic/site/smt-gst.nsf/eng/sf01130.html Link to the Covered List: Covered List [Vanstone Electronic (Beijing) Co., Ltd] (“the applicant”) certifies that the equipment for which authorization is sought is not “covered” equipment prohibited from receiving an equipment authorization pursuant to section 2.903 of the FCC rules. [Vanstone Electronic (Beijing) Co., Ltd] (“the applicant”) certifies that, as of the date of the filing of the application, the applicant [ is not] identified on the Covered list, established pursuant to §1.50002, as an entity producing “covered” equipment. Applicant Signature: Date:2023.8.9 Print Name: ZhiQin Shan Title: Quality Engineer *NOTE: This declaration cannot be signed by an Agent, it shall be signed by an authorized person listed in the FCC database

Vanstone Electronic (Beijing) Co., Ltd. Date: 2023-08-09 TO: Federal Communication Commission Equipment Authorization Branch 7435 Oakland Mills Road Columbia, MID 21046 Regarding: FCC ID: OWLA99 To whom it may concern: We, the undersigned, hereby authorize SGS-CSTC Standards Technical Services Co., Ltd. (SGS) and Keny Xu in SGS- CSTC Standards Technical Services Co., Ltd. (SGS) to act on our behalf in all manners relating to application for equipment authorization with respect to the FCC ID above, including signing of all documents relating to these matters. Any and all acts carried out by the agent on our behalf shall have the same effect as acts of our own.. We, the undersigned, hereby certify that we are not subject to a denial of federal benefits, that includes FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C. 853(a). Where our agent signs the application for certification on our behalf, I acknowledge that all responsibility for complying with the terms and conditions for Certification, as specified by SGS North America, Inc., still resides with Vanstone Electronic (Beijing) Co., Ltd. This authorization is valid until further written notice from the applicant. Print Name: ZhiQin Shan Title: Quality Engineer Signature: On behalf of Company: Vanstone Electronic (Beijing) Co., Ltd. Telephone: 86-10-88048100 E-mail: [email protected]

Vanstone Electronic (Beijing) Co., Ltd. TO: Federal Communication Commission Equipment Authorization Branch 7435 Oakland Mills Road Columbia, MID 21046 Regarding: Confidentiality Request regarding application for FCC ID: OWLA99 LONG TERM CONFIDENTIALITY Pursuant to 47 CFR Section 0.459 and 0.457 of the commission’s rules, the applicant hereby request confidential treatment of the documents listed below, associated with the certification application referenced above. Schematic(s) Block Diagrams Operational Descriptions Tune up procedure Software Security Description The documents above contain proprietary information not released to the public. Public disclosure of this information may prove harmful to the business of the applicant. Sincerely, Print Name: ZhiQin Shan Title: Quality Engineer Signature: On behalf of Company: Vanstone Electronic (Beijing) Co., Ltd. Telephone: 86-10-88048100 E-mail: [email protected]

SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch SZEMC-TRF-A02 Rev.A/0 Page: 1 of 7 Appendix External Photos for SZCR2306001888AT FCC ID: OWLA99 SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch SZEMC-TRF-A02 Rev.A/0 Page: 2 of 7 EUT Constructional Details (EUT Photos) SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch SZEMC-TRF-A02 Rev.A/0 Page: 3 of 7 SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch SZEMC-TRF-A02 Rev.A/0 Page: 4 of 7 SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch SZEMC-TRF-A02 Rev.A/0 Page: 5 of 7 SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch SZEMC-TRF-A02 Rev.A/0 Page: 6 of 7 SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch SZEMC-TRF-A02 Rev.A/0 Page: 7 of 7 - End of the Appendix -

Android POS Terminal A99 5V 2A C15B-6BEF-0RA8-4EN-0B0 S / N :XXXXXXXXXXX （Made In China) FCC ID: OWLA99

SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch SZEMC-TRF-A03 Rev.A/0 Page: 1 of 6 Appendix Internal Photos for SZCR2306001888AT FCC ID: OWLA99 SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch SZEMC-TRF-A03 Rev.A/0 Page: 2 of 6 EUT Constructional Details (EUT Photos) WWAN antenna GPS antenna NFC antenna SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch SZEMC-TRF-A03 Rev.A/0 Page: 3 of 6 BTWIFI antenna SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch SZEMC-TRF-A03 Rev.A/0 Page: 4 of 6 SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch SZEMC-TRF-A03 Rev.A/0 Page: 5 of 6 SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch SZEMC-TRF-A03 Rev.A/0 Page: 6 of 6 - End of the Appendix -

SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch Report No.: SZCR230600188811 Page: 1 of 1 Appendix C Calibration certificate Equipment Manufacturer Model Serial Number Certificate No: Dipole SPEAG D835V2 4d042 Z22-60172 Dipole SPEAG D1800V2 254 Z22-60188 Dipole SPEAG D1950V3 1138 Z22-60488 Dipole SPEAG D2450V2 955 Z22-60107 Dipole SPEAG D2600V2 1125 Z22-60181 Dipole SPEAG D5GHzV2 1042 Z22-60176 DAE SPEAG DAE4 760 J23Z60309 E-field PROBE SPEAG EX3DV4 7380 J23Z60276

SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch SZSAR-TRF-01-A01 Rev. A/0 May15,2023 Report No.: SZCR230600188811 Page: 1 of 100 Keny Xu EMC Laboratory Manager FCC SAR TEST REPORT Application No.: SZCR2306001888AT Applicant: Vanstone Electronic (Beijing) Co., Ltd. Address of Applicant: 3F No.2 Building, Aisino Corporation Park 18A, Xingshikou Road, Haidian District, Beijing, China 100195 Manufacturer: Vanstone Electronic (Beijing) Co., Ltd. Address of Manufacturer: 3F No.2 Building, Aisino Corporation Park 18A, Xingshikou Road, Haidian District, Beijing, China 100195 Product Name: Android POS Terminal Model No.(EUT): A99 Trade mark: Aisino FCC ID: OWLA99 Standard(s) : FCC 47CFR §2.1093 Date of Receipt: 2023-07-06 Date of Test: 2023-07-07 to 2023-07-23 Date of Issue: 2023-07-25 Test Result: Pass* * In the configuration tested, the EUT complied with the standards specified above. SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch SZSAR-TRF-01-A01 Rev. A/0 May15,2023 Report No.: SZCR230600188811 Page: 2 of 100 Revision Record Version Description Date Remark 00 Original 2023-07-25 / Authorized for issue by: Owen Xiao / Project Engineer Eric Fu / Reviewer SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch SZSAR-TRF-01-A01 Rev. A/0 May15,2023 Report No.: SZCR230600188811 Page: 3 of 100 TEST SUMMARY Frequency Band Maximum Reported SAR(W/kg) Extremity GSM850 0.821 GSM1900 1.179 WCDMA Band II 2.219 WCDMA Band IV 1.992 WCDMA Band V 0.824 LTE Band 2 1.861 LTE Band 4 1.379 LTE Band 5 0.74 LTE Band 7 2.321 LTE Band 38 1.321 Bluetooth 0.19 WI-FI (2.4GHz) 0.29 WI-FI (5GHz) 0.702 SAR Limited(W/kg) 4 Maximum Simultaneous Transmission SAR (W/kg) Scenario Extremity Sum SAR 2.375 SPLSR N/A SPLSR Limited 0.1 SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch SZSAR-TRF-01-A01 Rev. A/0 May15,2023 Report No.: SZCR230600188811 Page: 4 of 100 CONTENTS 1 GENERAL INFORMATION......................................................................................................................... 6 1.1 GENERAL DESCRIPTION OF EUT ............................................................................................................ 6 1.1.1 DUT Antenna Locations .................................................................................................................. 7 1.2 TEST SPECIFICATION............................................................................................................................. 8 1.3 RF EXPOSURE LIMITS ............................................................................................................................ 9 1.4 TEST LOCATION ...................................................................................................................................10 1.5 TEST FACILITY .....................................................................................................................................10 2 LABORATORY ENVIRONMENT ...............................................................................................................11 3 SAR MEASUREMENTS SYSTEM CONFIGURATION ...............................................................................12 3.1 THE SAR MEASUREMENT SYSTEM ........................................................................................................12 3.2 ISOTROPIC E-FIELD PROBE EX3DV4 .....................................................................................................14 3.3 DATA ACQUISITION ELECTRONICS (DAE) ...............................................................................................15 3.4 SAM TWIN PHANTOM ...........................................................................................................................15 3.5 ELI PHANTOM .....................................................................................................................................16 3.6 DEVICE HOLDER FOR TRANSMITTERS.....................................................................................................17 3.7 MEASUREMENT PROCEDURE .................................................................................................................18 3.7.1 Scanning procedure ......................................................................................................................18 3.7.2 Data Storage .................................................................................................................................20 3.7.3 Data Evaluation by SEMCAD ........................................................................................................20 4 SAR MEASUREMENT VARIABILITY AND UNCERTAINTY .....................................................................22 4.1 SAR MEASUREMENT VARIABILITY...........................................................................................................22 4.2 SAR MEASUREMENT UNCERTAINTY ........................................................................................................23 5 DESCRIPTION OF TEST POSITION .........................................................................................................24 5.1 EXTREMITY EXPOSURE CONDITIONS .......................................................................................................24 6 SAR SYSTEM VERIFICATION PROCEDURE ...........................................................................................25 6.1 TISSUE SIMULATE LIQUID ......................................................................................................................25 6.1.1 Recipes for Tissue Simulate Liquid ................................................................................................25 6.1.2 Test Liquids Confirmation ..............................................................................................................26 6.1.3 Measurement for Tissue Simulate Liquid ..........................................................................…

Text truncated - open the document above for the full version.

Applicable to A99-SC200E-AU project WIFI antenna solution Electrical Specifications： Frequency BandWIFIThe Antenna MaterialFPC Nominal Impedance50ΩAntenna Connection ModeTouch VSWR≤3.0Working Temperature-40°C～+85°C Peak Gain 2400-2500MHz：2.11dBiKeep The Temperature+19°C～+23°C 5100-5800MHz：4.56dBiPolarizationLinear Polarization Test Conditions And Methods: Test InstrumentsTest MethodTest Result E5071B network analyzer 48 probe test system MT8862 comprehensive tester 1. Assemble the antenna to be tested on the prototype. 2. Put the prototype on the test fixture in a dark room, and conduct comprehensive test with it.Instrument/analyzer connection is established. 3. Test antenna passive data with test software. Refer to the Test Report Room 308, Block B, Cybernino Gene Therapy Park, No. 19, Science and Technology Road 1, Nanshan District, Shenzhen, China Product drawings Passive performance test parameters Frequency(GHz) 2.4 2.5 VSWR 2.2 1.8 Frequency(GHz) 5.155.85 VSWR 1.91.8 Antenna Passive Data： FreqEffiGain (MHz)(%)(dBi) 240037.261.88 241039.852.11 242036.241.62 243038.522.08 244032.591.17 245035.141.24 246030.250.5 247033.281.16 248031.10.61 249034.361.23 250030.290.58 520040.344.56 522036.534.14 524035.553.95 526034.543.84 528036.463.95 530036.263.67 532037.883.52 534039.53.29 536039.333.17 538039.012.72 540036.412.3 542036.722.29 544037.332.53 546036.52.58 548037.842.8 550042.143.53 552039.513.26 554036.912.81 556036.862.71 558036.582.6 560035.882.3 562037.152.32 564037.412.2 566038.812.38 568041.793.07 570042.93.42 572045.283.89 574047.124.19 576048.214.38 578044.694.21 580047.834.49 Directional diagram Display Picture:

SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch SZEMC-TRF-01 Rev. A/0 Aug01,2022 Report No.: SZCR230600188802 Page: 1 of 89 Keny Xu EMC Laboratory Manager TEST REPORT Application No.: SZCR2306001888AT Applicant: Vanstone Electronic (Beijing) Co., Ltd. Address of Applicant: 3F No.2 Building, Aisino Corporation Park 18A, Xingshikou Road, Haidian District, Beijing, China 100195 Manufacturer: Vanstone Electronic (Beijing) Co., Ltd. Address of Manufacturer: 3F No.2 Building, Aisino Corporation Park 18A, Xingshikou Road, Haidian District, Beijing, China 100195 Equipment Under Test (EUT): EUT Name: Android POS Terminal Model No.: A99 FCC ID: OWLA99 Standard(s) : 47 CFR Part 15, Subpart C 15.247 Date of Receipt: 2023-06-16 Date of Test: 2023-06-20 to 2023-07-18 Date of Issue: 2023-07-22 Test Result: Pass* * In the configuration tested, the EUT complied with the standards specified above. SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch SZEMC-TRF-01 Rev. A/0 Aug01,2022 Report No.: SZCR230600188802 Page: 2 of 89 Revision Record Version Chapter Date Modifier Remark 01 2023-07-22 Original Authorized for issue by: Calvin Weng/Project Engineer Eric Fu/Reviewer SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch SZEMC-TRF-01 Rev. A/0 Aug01,2022 Report No.: SZCR230600188802 Page: 3 of 89 2 Test Summary Radio Spectrum Technical Requirement Item Standard Method Requirement Result Antenna Requirement 47 CFR Part 15, Subpart C 15.247 N/A 47 CFR Part 15, Subpart C 15.203 & 15.247(b)(4) Pass Other requirements Frequency Hopping Spread Spectrum System Hopping Sequence N/A 47 CFR Part 15, Subpart C 15.247(a)(1),(g),(h) Pass Radio Spectrum Matter Part Item Standard Method Requirement Result Conducted Emissions at AC Power Line (150kHz-30MHz) 47 CFR Part 15, Subpart C 15.247 ANSI C63.10 (2013) Section 6.2 47 CFR Part 15, Subpart C 15.207 Pass Conducted Peak Output Power ANSI C63.10 (2013) Section 7.8.5 47 CFR Part 15, Subpart C 15.247(b)(1) Pass 20dB Bandwidth ANSI C63.10 (2013) Section 7.8.7 47 CFR Part 15, Subpart C 15.247(a)(1) Pass Carrier Frequencies Separation ANSI C63.10 (2013) Section 7.8.2 47 CFR Part 15, Subpart C 15.247a(1) Pass Hopping Channel Number ANSI C63.10 (2013) Section 7.8.3 47 CFR Part 15, Subpart C 15.247a(1)(iii) Pass Dwell Time ANSI C63.10 (2013) Section 7.8.4 47 CFR Part 15, Subpart C 15.247a(1)(iii) Pass Conducted Band Edges Measurement ANSI C63.10 (2013) Section 7.8.6 47 CFR Part 15, Subpart C 15.247(d) Pass Conducted Spurious Emissions ANSI C63.10 (2013) Section 7.8.8 47 CFR Part 15, Subpart C 15.247(d) Pass Radiated Emissions which fall in the restricted bands ANSI C63.10 (2013) Section 6.10.5 47 CFR Part 15, Subpart C 15.205 & 15.209 Pass Radiated Spurious Emissions Below 1GHz ANSI C63.10 (2013) Section 6.4,6.5 47 CFR Part 15, Subpart C 15.205 & 15.209 Pass Radiated Spurious Emissions Above 1GHz ANSI C63.10 (2013) Section 6.6 47 CFR Part 15, Subpart C 15.205 & 15.209 Pass SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch SZEMC-TRF-01 Rev. A/0 Aug01,2022 Report No.: SZCR230600188802 Page: 4 of 89 3 Contents Page 1 Cover Page ......................................................................................................................................... 1 2 Test Summary ..................................................................................................................................... 3 3 Contents ............................................................................................................................................. 4 4 General Information............................................................................................................................ 6 4.1 Details of E.U.T. ........................................................................................................................... 6 4.2 Description of Support Units ......................................................................................................... 6 4.3 Measurement Uncertainty ............................................................................................................ 7 4.4 Test Location ............................................................................................................................... 8 4.5 Test Facility .................................................................................................................................. 8 4.6 Deviation from Standards ............................................................................................................. 8 4.7 Abnormalities from Standard Conditions ....................................................................................... 8 5 Equipment List ................................................................................................................................... 9 6 Radio Spectrum Technical Requirement ..........................................................................................13 6.1 Antenna Requirement .................................................................................................................13 6.1.1 Test Requirement: ..................................................................................................................13 6.1.2 Conclusion ..............................................................................................................................13 6.2 Other requirements Frequency Hopping Spread Spectrum System Hopping Sequence ...............14 6.2.1 Test Requirement: ..................................................................................................................14 6.2.2 Conclusion ..............................................................................................................................14 7 Radio Spectrum Matter Test Results ................................................................................................16 7.1 Conducted Emissions at AC Po…

Text truncated - open the document above for the full version.

SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch SZSAR-TRF-01-A01 Rev. A/0 May15,2023 Page: 1 of 7 Appendix D for SZCR2306001888AT Photographs 1. SAR measurement System 2. Photographs of Tissue Simulate Liquid 3. Photographs of EUT test position 4. EUT Antenna Locations 5. EUT Constructional Details SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch SZSAR-TRF-01-A01 Rev. A/0 May15,2023 Page: 2 of 7 1. SAR measurement System SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch SZSAR-TRF-01-A01 Rev. A/0 May15,2023 Page: 3 of 7 2. Photographs of Tissue Simulate Liquid Tissue Simulant Liquid for Head 600MHz-6GHz SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch SZSAR-TRF-01-A01 Rev. A/0 May15,2023 Page: 4 of 7 3. Photographs of EUT test position Front side 0mm Back side 0mm Left side 0mm Right side 0mm SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch SZSAR-TRF-01-A01 Rev. A/0 May15,2023 Page: 5 of 7 Top side 0mm Bottom side 0mm SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch SZSAR-TRF-01-A01 Rev. A/0 May15,2023 Page: 6 of 7 4. EUT Antenna Locations SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch SZSAR-TRF-01-A01 Rev. A/0 May15,2023 Page: 7 of 7 5. EUT Constructional Details Details please Refer to Appendix – Photographs of EUT Constructional Details for SZCR2306001888AT.

SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch SZEMC-TRF-A04 Rev.A/0 Page: 1 of 3 Appendix BT/WIFI Test Setup Photos for SZCR2306001888AT FCC ID: OWLA99 SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch SZEMC-TRF-A04 Rev.A/0 Page: 2 of 3 Test Setup Photo Conducted Emissions at AC Power Line (150kHz-30MHz) Radiated Spurious Emissions Below 1GHz SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch SZEMC-TRF-A04 Rev.A/0 Page: 3 of 3 Radiated Spurious Emissions Above 1GHz…

Text truncated - open the document above for the full version.