OXZPCLK2020PRECOlink

www.preco.com PRECOlink PLW8003 PLW8004 Operating Manual This page left blank intentionally This page left blank intentionally FCC STATEMENT This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Warning: Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. NOTE: This equipment has been tested and found to comply with the limits of a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try and correct the interference. INDUSTRY CANADA STATEMENT Per RSS-Gen, Section 8.4 This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. Per RSS - Gen, Section 8.4 Cet appareil est conforme à Industrie Canada exempts de licence standards RSS. Le fonctionnement est soumis aux deux conditions suivantes : (1 ) ce dispositif ne peut pas provoquer d'interférences et ( 2) cet appareil doit accepter toute interférence , y compris les interférences qui peuvent causer un mauvais fonctionnement de l'appareil. This radio transmitter, 20379-PRECOLINK, has been approved by Innovation, Science and Economic Development Canada to operate with the antenna type listed below, with the maximum permissible gain indicated. Antenna types not included in this list that have a gain greater than the maximum gain indicated for any type listed are strictly prohibited for use with this device. Manufacturer: Antenna Factor by Linx Model number: ANT-2.4-ID-2000-SMA Peak Gain: 3.0dBi max Impedance: 50-ohms REGULATORY COMPLIANCE The PreView Side Defender ® II sensor is compliant with the following countries/regions and their regulations as of the published date of this manual. The sensor may be compliant in other countries/regions. Please check your local regulations or contact PRECO Electronics ® for support. • United States - FCC- Part 15.247 o FCC ID: OXZPCLK2020 • Canada - RSS-247:2017 o IC ID:20379-PRECOLINK • European Union - ETSI EN300 328 V2.3.3:2019-07. ETSI EN301 489-17 V3.1.1:2017 • Australia/New Zealand – AS/NZS 4268:2017 Patent pending This document may be amended, corrected, and enhanced in keeping with the sensor development progress. The most recent version can be found at www.preco.com TRADEMARKS The names of actual companies and products mentioned herein may be the trademarks of their respective owners. Any rights not expressly granted herein are reserved. Contents Safety Symbols and signal words .................................................................. 1 Daily Maintenance ..................................................................................... 2 Product Description .................................................................................... 3 2.1 System Operation .............................................................................. 4 Installation .................................................................................................. 6 3.1 Before you Begin ............................................................................... 6 3.2 PRECOlink Install Location ................................................................ 6 3.3 System Connections .......................................................................... 6 PRECOlink Pin Out ...................................................................................... 7 Troubleshooting .......................................................................................... 8 Specifications ............................................................................................. 8 Warranty Information ................................................................................. 9 More PRECO Electronics ® Safety Products .....................................................10 (866) 977-7326 www.preco.com 3700262 Copyright 2019 Page 1 Safety Symbols and signal words Indicates a hazardous situation that, if not avoided, could result in death or serious injury Indicates a hazardous situation that, if not avoided, could result in minor or moderate injury Indicates information considered important, but not hazard-related This operating manual should be stored in a safe place and be referred to when maintaining and/or reinstalling the system. PRECOlink is an integral part of your PreView ® object detection system. The following notices and daily maintenance apply to all systems that utilize PRECOlink technology. If the PRECO Electronics® system is not maintained properly, it may not operate as intended, which may result in a failure to warn the operator of a hazardous situation. Failure to follow all safety precautions and instruction may result in property damage, serious injury, or death. It is necessary to read, understand and follow all instructions shipped with the product. The PreView ® system is intended as an Object Detection System and should not be relied upon as the first line of defense for the safe operation of the equipment. It should be used in conjuncti…

Text truncated - open the document above for the full version.

PRECO ELECTRONICS, INC. 10335 W. Emerald Street Boise, Idaho 83704 Phone: (208) 323-1000 Fax: (208) 323-1034 www.PreViewRadar.com August 12, 2020 Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, Maryland 21046 Re: Preco Electronics PRECOlink Wireless CAN unit FCC ID: OXZPCLK2020 To whom it may concern: Preco Electronics is seeking original certification for PRECOlink PWL800_ Wireless CAN unit. The name of the unit is PRECOlink and the models are PWL8003 for the coordinator unit and PWL8004 for the end device unit. The difference between coordinator and end device units is software only, the hardware is identical. The PRECOlink RADIO is an IEEE802.15.4 wireless microcontroller module. The module has three antennas that operate in the 2.4 GHz band. The two 2.4 GHz integral internal antennas are a type PCB trace PIFA (planar inverted-F antenna) residing on a RF circuit board with a realized gain of 2.7 dBi for antenna 1 and 4.6 dBi for antenna 2. The circuit board is then installed in a sealed plastic housing. The external antenna is a type dipole whip antenna that connects via a SMA connector on the outside of the housing. The gain for the external antenna is 3.0 dBi. The three antennas scan 15 channels for the least congested channel. The channel allocation is as follows. NOTE: PRECOlink does not use channel 26, the highest available channel in the band per the Zigbee standard. Channel Center Frequency (GHz) Channel Center Frequency (GHz) 11 2.405 18 2.44 12 2.41 19 2.445 13 2.415 20 2.45 14 2.42 21 2.455 15 2.425 22 2.46 16 2.43 23 2.465 17 2.435 24 2.47 25 2.475 The housing on each unit is the same, only the print on the label differs. The sensors have the same circuit board, transmit power and Effective Isotropic Radiated Power (EIRP). Approval is being sought under FCC Part 15.247 (2.4 GHz). Sincerely, ______________________ Donny Lloyd

PRECO ELECTRONICS, INC. 10335 W. Emerald Street Boise, Idaho 83704 Phone: (208) 323-1000 Fax: (208) 323-1034 www.Preco.com July 28, 2020 Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, Maryland 21046 Re: Preco Electronics PRECOlink Wireless CAN module FCC ID: OXZPCLK2020 To whom it may concern: Preco Electronics respectfully requests that under the provision of 47 CFR 0.459 and 47 CFR 0.457 (d), the documents listed below and attached with this application for certification be provided with long-term confidential status. The items listed below contain detailed schematic diagrams submitted to the FCC for review with this application. These schematics contain proprietary information regarding the circuit operation and capabilities that are the result of Preco Electronics extensive investment in research and development. Without the disclosed information, competitive organizations would take considerably more time to assess and develop a competitive product. We therefore formally request that the materials listed below be kept strictly confidential and not made available for inspection by any other party, except on a need to know basis for the sole purpose of the certification process. Confidential Items (long-term): • Schematics • Operational Description • Frequency Block Diagrams Sincerely, ________________________ Donny Lloyd Compliance Specialist R & D Engineer PRECO Electronics, Inc

JN5169-001-M06-2 ExternalPhotos TOP BOTTOM

PRECO ELECTRONICS, INC. 10335 W. Emerald Street Boise, Idaho 83704 Phone: (208) 323-1000 Fax: (208) 323-1034 www.PreViewRadar.com PRECOlink PWL800_External Photographs Label information in the included photos is for label placement reference only. The FCC and IC numbers are not reflective of the actual numbers assigned. PRECOlink models PWL8003 & PWL8004 use the same enclosure. The Model ambiguity is reflected as PWL800_. Front – PRECOlink Wireless CAN Module PWL800_ Back – PRECOlink Wireless CAN Module PWL800_ PRECO ELECTRONICS, INC. 10335 W. Emerald Street Boise, Idaho 83704 Phone: (208) 323-1000 Fax: (208) 323-1034 www.PreViewRadar.com Bottom - PRECOlink Wireless CAN Module PWL800_ Top - PRECOlink Wireless CAN Module PWL800_ PRECO ELECTRONICS, INC. 10335 W. Emerald Street Boise, Idaho 83704 Phone: (208) 323-1000 Fax: (208) 323-1034 www.PreViewRadar.com Left Side – PRECOlink Wireless CAN Module PWL800_ Right Side – PRECOlink Wireless CAN Module PWL800_

PRECO ELECTRONICS, INC. 10335 W. Emerald Street Boise, Idaho 83704 Phone: (208) 323-1000 Fax: (208) 323-1034 www.Preco.com PRECOlink Label Location (FCC) PRECOlink model numbers PWL8003 (Coordinator) and PWL8004 (End Device) label – Front PRECOlink FCC and IC ID label – Back

PRECO ELECTRONICS, INC. 10335 W. Emerald Street Boise, Idaho 83704 Phone: (208) 323-1000 Fax: (208) 323-1034 www.Preco.com PRECOlink Internal Photos PRECOlink top view – Close ups on the following pages SMA antenna connection to board PRECO ELECTRONICS, INC. 10335 W. Emerald Street Boise, Idaho 83704 Phone: (208) 323-1000 Fax: (208) 323-1034 www.Preco.com PRECOlink closeup part 1. SMA connector traces, antenna 3 SMA antenna connection to board Antennas 1 & 2 (next picture) PRECO ELECTRONICS, INC. 10335 W. Emerald Street Boise, Idaho 83704 Phone: (208) 323-1000 Fax: (208) 323-1034 www.Preco.com PRECOlink closeup part 2. Antenna 1 & 2 PRECO ELECTRONICS, INC. 10335 W. Emerald Street Boise, Idaho 83704 Phone: (208) 323-1000 Fax: (208) 323-1034 www.Preco.com NXP JN5169-001M06-2 radio module PRECO ELECTRONICS, INC. 10335 W. Emerald Street Boise, Idaho 83704 Phone: (208) 323-1000 Fax: (208) 323-1034 www.Preco.com PRECOlink PCA – Bottom

JN5169-001-M06-2 InternalPhotos TOP BOTTOM

PRECO ELECTRONICS, INC. 10335 W. Emerald Street Boise, Idaho 83704 Phone: (208) 323-1000 Fax: (208) 323-1034 www.PreViewRadar.com July 27, 2020 Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, Maryland 21046 PRECOlink wireless CAN module PWL8003 Coordinator unit and PWL8004 End Device unit Antenna Information. FCC ID: OXZPCLK2020 Preco Electronics PRECOlink PWl8003 and PWL8004 compiles with the antenna requirements of paragraph 15.203 of the FCC rules. The 2.4 GHz integral internal antennas are a type PCB trace PIFA (planar inverted-F antenna) residing on a RF circuit board with a realized gain of 2.7 dBi for antenna 1 and 4.6 dBi for antenna 2. The circuit board is then installed in a sealed plastic housing. The external antenna is a type dipole whip antenna that connects via a SMA connector on the outside of the housing. The gain for the external antenna is 3.0 dBi. Photos of each respective antenna are below. Details of compliance by Preco electronics is as follows. Antennas 1 and 2 are sealed inside the unit and are therefore, inaccessible to the user. Antenna 3 on the device is only to be installed by a professional installer that is recommended by Preco electronics. Only the recommended SMA antenna shall be used (ANT-2.4-ID-1000-SMA or ANT-2.4-ID-2000-SMA). Use of other antennas may damage unit or cause disruptions in inter-unit communication. The PRECOlink is available for commercial purchase only. The PRECOlink is not available for sale at retail outlets, to the general public, or by mail order. Only professional installers for Preco electronics authorized dealers shall be permitted to install the PRECOlink and the corresponding external antenna onto a machine or vehicle. The PRECOlink is unique in that, professional installation is needed to pair two PRECOlink units together, one as a ‘coordinator device’ and the second, as an ‘end device’ unit. Professional installation is also required to ensure that The PRECOlink system correctly transfers CAN communication data throughout the system. Antennas 1, 2, and 3 shown below. PRECO ELECTRONICS, INC. 10335 W. Emerald Street Boise, Idaho 83704 Phone: (208) 323-1000 Fax: (208) 323-1034 www.PreViewRadar.com Antenna 1 Antenna 2 SMA Antenna Connection Board View SMA Antenna Connection External View SMA External Antenna (ANT-2.4-ID-2000-SMA) Sincerely, ________________________ Donny Lloyd Compliance Specialist R & D Engineer PRECO Electronics, Inc

This report must not be used to claim product certification, approval, or endorsement by NVLAP, NIST, or any agency of the U.S. Government. This Report shall not be reproduced, except in full without written approval of the laboratory. EAR-Controlled Data - This document contains technical data whose export and reexport/retransfer is subject to control by the U.S. Department of Commerce under the Export Administration Act and the Export Administration Regulations. The Department of Commerce’s prior written approval may be required for the export or re- export/retransfer of such technical data to any foreign person, foreign entity or foreign organization whether in the United States or abroad. More: https://www.bis.doc.gov/index.php/forms-documents/regulations-docs/14-commerce-country-chart/fileT Preco, Inc. PRECOlink FCC 2.1091:2019 2.4 GHz 802.15.4 (Zigbee) Report: PRCO0113.6 NVLAP Lab Code: 200630-0 CERTIFICATE OF EVALUATION 2018-09-14 Product compliance is the responsibility of the client; therefore, the tests and equipment modes of operation represented in this report were agreed upon by the client, prior to testing. The results of this test pertain only to the sample(s) tested. The specific description is noted in each of the individual sections of the test report supporting this certificate of test. This report reflects only those tests from the referenced standards shown in the certificate of test. It does not include inspection or verification of labels, identification, marking or user information. As indicated in the Statement of Work sent with the quotation, Element’s standard process is to always use the latest published version of the test methods even when earlier versions are cited in the test specification. Issuance of a purchase order was de facto acceptance of this approach. Otherwise, the client would have advised Element in writing of the specific version of the test methods they wanted applied to the subject testing Last Date of Evaluation: Thursday, August 13, 2020 Preco, Inc. EUT: PRECOlink RF Exposure Evaluation Standards Specification Method FCC 2.1091:2019 FCC 447498 D01 General RF Exposure Guidance v06 Results Method Clause Description Applied Results Comments 7.1 Maximum Permissible Exposure Yes Pass Deviations From Evaluation Standards None Approved By: Donald Facteau, Process Architect Report No. PRCO0113.6EAR-Controlled Data2/9 REVISION HISTORY 2018.07.17 Revision Number Description Date (yyyy-mm-dd) Page Number 00 None Report No. PRCO0113.6EAR-Controlled Data3/9 ACCREDITATIONS AND AUTHORIZATIONS 2019.03.08 United States FCC - Designated by the FCC as a Telecommunications Certification Body (TCB). Certification chambers, Open Area Test Sites, and conducted measurement facilities are listed with the FCC. A2LA - Accredited by A2LA to ISO / IEC 17065 as a product certifier. This allows Element to certify transmitters to FCC and IC specifications. NVLAP - Each laboratory is accredited by NVLAP to ISO 17025 Canada ISED - Recognized by Innovation, Science and Economic Development Canada as a Certification Body (CB) and as a CAB for the acceptance of test data. European Union European Commission – Within Element, we have a EU Notified Body validated for the EMCD and RED Directives. Australia/New Zealand ACMA - Recognized by ACMA as a CAB for the acceptance of test data. Korea MSIT / RRA - Recognized by KCC’s RRA as a CAB for the acceptance of test data. Japan VCCI - Associate Member of the VCCI. Conducted and radiated measurement facilities are registered. Taiwan BSMI – Recognized by BSMI as a CAB for the acceptance of test data. NCC - Recognized by NCC as a CAB for the acceptance of test data. Singapore IDA – Recognized by IDA as a CAB for the acceptance of test data. Israel MOC – Recognized by MOC as a CAB for the acceptance of test data. Hong Kong OFCA – Recognized by OFCA as a CAB for the acceptance of test data. Vietnam MIC – Recognized by MIC as a CAB for the acceptance of test data. SCOPE For details on the Scopes of our Accreditations, please visit: https://www.nwemc.com/emc-testing-accreditations Report No. PRCO0113.6EAR-Controlled Data4/9 FACILITIES 2019.03.08 California Labs OC01-17 41 Tesla Irvine, CA 92618 (949) 861-8918 Minnesota Labs MN01-10 9349 W Broadway Ave. Brooklyn Park, MN 55445 (612)-638-5136 Oregon Labs EV01-12 6775 NE Evergreen Pkwy #400 Hillsboro, OR 97124 (503) 844-4066 Texas Labs TX01-09 3801 E Plano Pkwy Plano, TX 75074 (469) 304-5255 Washington Labs NC01-05 19201 120 th Ave NE Bothell, WA 98011 (425)984-6600 NVLAP NVLAP Lab Code: 200676-0 NVLAP Lab Code: 200881-0 NVLAP Lab Code: 200630-0 NVLAP Lab Code:201049-0 NVLAP Lab Code: 200629-0 Innovation, Science and Economic Development Canada 2834B-1, 2834B-3 2834E-1, 2834E-3 2834D-1 2834G-1 2834F-1 BSMI SL2-IN-E-1154R SL2-IN-E-1152R SL2-IN-E-1017 SL2-IN-E-1158R SL2-IN-E-1153R VCCI A-0029 A-0109 A-0108 A-0201 A-0110 Recognized Phase I CAB for ISED, ACMA, BSMI, IDA, KCC/RRA, MIC, MOC, NCC, OFCA US0158 US0175 US0017 US0191 US0157 Report No. PRCO0113.6EAR-Controlled Data5/9 PRODUCT DESCRIPTION 2018-07-17 Client and Equipment Under Evaluation Information Company Name: Preco, Inc. Address: 10335 West Emerald Street City, State, Zip: BOISE, ID 83704 Evaluation Requested By: Bryan Holloway EUT: PRECOlink Date of Evaluation: Thursday, August 13, 2020 Information Provided by the Party Requesting the Evaluation Functional Description of the Equipment: The PRECOlink is a wireless CAN bus device for vehicles marketed as an after-market accessory. The 802.15.4 (Zigbee) radio operates in the 2.4 GHz unlicensed band. The product has three different antennas (for diversity). Two of the antennas are on-board PCB trace antennas. The third antenna path is to an SMA port for connection to an external antenna. Objective: To demonstrate compliance with FCC requirements for RF exposure for 2.1091 mobile/fixed devices Report No. PRCO0113.6EAR-Controlled Data6/9 RF Exposure Condition 2018-07-17 The following RF Expo…

Text truncated - open the document above for the full version.

This report must not be used to claim product certification, approval, or endorsement by NVLAP, NIST, or any agency of the U.S. Government. This Report shall not be reproduced, except in full without written approval of the laboratory. EAR-Controlled Data - This document contains technical data whose export and reexport/retransfer is subject to control by the U.S. Department of Commerce under the Export Administration Act and the Export Administration Regulations. The Department of Commerce’s prior written approval may be required for the export or re- export/retransfer of such technical data to any foreign person, foreign entity or foreign organization whether in the United States or abroad. Preco, Inc. PRECOlink FCC 15.247:2020 2.4GHz DTS Report: PRCO0113, Issue Date: April 15, 2020 NVLAP LAB CODE: 200630-0 CERTIFICATE OF TEST 2018-09-14 Product compliance is the responsibility of the client; therefore, the tests and equipment modes of operation represented in this report were agreed upon by the client, prior to testing. The results of this test pertain only to the sample(s) tested. The specific description is noted in each of the individual sections of the test report supporting this certificate of test. This report reflects only those tests from the referenced standards shown in the certificate of test. It does not include inspection or verification of labels, identification, marking or user information. As indicated in the Statement of Work sent with the quotation, Element’s standard process is to always use the latest published version of the test methods even when earlier versions are cited in the test specification. Issuance of a purchase order was de facto acceptance of this approach. Otherwise, the client would have advised Element in writing of the specific version of the test methods they wanted applied to the subject testing. Last Date of Test: March 30, 2020 Preco, Inc. EUT: PRECOlink Radio Equipment Testing Standards Specification Method FCC 15.247:2020 ANSI C63.10:2013, KDB 558074 Results Method Clause Test Description Applied Results Comments 6.2 Powerline Conducted Emissions No N/A Not required for a product intended for vehicular use 11.6 Duty Cycle Yes Pass 11.8.2 Occupied Bandwidth Yes Pass 11.9.1.1 Output Power Yes Pass 11.9.1.1 Equivalent Isotropic Radiated Power Yes Pass 11.10.2 Power Spectral Density Yes Pass 11.11 Band Edge Compliance Yes Pass 11.11 Spurious Conducted Emissions Yes Pass 11.12.1, 11.13.2, 6.5, 6.6 Spurious Radiated Emissions Yes Pass 11.12.1, 11.13.2, 6.5, 6.6 Spurious Radiated Emissions Yes Pass Deviations From Test Standards None Approved By: Kyle Holgate, Operations Manager Report No. PRCO01132/72 REVISION HISTORY 2018.07.17 Revision Number Description Date (yyyy-mm-dd) Page Number 00 None Report No. PRCO01133/72 ACCREDITATIONS AND AUTHORIZATIONS 2019.03.08 United States FCC - Designated by the FCC as a Telecommunications Certification Body (TCB). Certification chambers, Open Area Test Sites, and conducted measurement facilities are listed with the FCC. A2LA - Accredited by A2LA to ISO / IEC 17065 as a product certifier. This allows Element to certify transmitters to FCC and IC specifications. NVLAP - Each laboratory is accredited by NVLAP to ISO 17025 Canada ISED - Recognized by Innovation, Science and Economic Development Canada as a Certification Body (CB) and as a CAB for the acceptance of test data. European Union European Commission – Within Element, we have a EU Notified Body validated for the EMCD and RED Directives. Australia/New Zealand ACMA - Recognized by ACMA as a CAB for the acceptance of test data. Korea MSIT / RRA - Recognized by KCC’s RRA as a CAB for the acceptance of test data. Japan VCCI - Associate Member of the VCCI. Conducted and radiated measurement facilities are registered. Taiwan BSMI – Recognized by BSMI as a CAB for the acceptance of test data. NCC - Recognized by NCC as a CAB for the acceptance of test data. Singapore IDA – Recognized by IDA as a CAB for the acceptance of test data. Israel MOC – Recognized by MOC as a CAB for the acceptance of test data. Hong Kong OFCA – Recognized by OFCA as a CAB for the acceptance of test data. Vietnam MIC – Recognized by MIC as a CAB for the acceptance of test data. SCOPE For details on the Scopes of our Accreditations, please visit: https://www.nwemc.com/emc-testing-accreditations Report No. PRCO01134/72 FACILITIES 2019.03.08 California Labs OC01-17 41 Tesla Irvine, CA 92618 (949) 861-8918 Minnesota Labs MN01-10 9349 W Broadway Ave. Brooklyn Park, MN 55445 (612)-638-5136 Oregon Labs EV01-12 6775 NE Evergreen Pkwy #400 Hillsboro, OR 97124 (503) 844-4066 Texas Labs TX01-09 3801 E Plano Pkwy Plano, TX 75074 (469) 304-5255 Washington Labs NC01-05 19201 120 th Ave NE Bothell, WA 98011 (425)984-6600 NVLAP NVLAP Lab Code: 200676-0 NVLAP Lab Code: 200881-0 NVLAP Lab Code: 200630-0 NVLAP Lab Code:201049-0 NVLAP Lab Code: 200629-0 Innovation, Science and Economic Development Canada 2834B-1, 2834B-3 2834E-1, 2834E-3 2834D-1 2834G-1 2834F-1 BSMI SL2-IN-E-1154R SL2-IN-E-1152R SL2-IN-E-1017 SL2-IN-E-1158R SL2-IN-E-1153R VCCI A-0029 A-0109 A-0108 A-0201 A-0110 Recognized Phase I CAB for ISED, ACMA, BSMI, IDA, KCC/RRA, MIC, MOC, NCC, OFCA US0158 US0175 US0017 US0191 US0157 Report No. PRCO01135/72 MEASUREMENT UNCERTAINTY TMU.2015.07.10 Measurement Uncertainty When a measurement is made, the result will be different from the true or theoretically correct value. The difference is the result of tolerances in the measurement system that cannot be completely eliminated. To the extent that technology allows us, it has been our aim to minimize this error. Measurement uncertainty is a statistical expression of measurement error qualified by a probability distribution. A measurement uncertainty estimation has been performed for each test per our internal quality document QM205.4.6. The estimation is used to compare the measured result with its "true" or theoretically correct value. The expanded measur…

Text truncated - open the document above for the full version.

XMit 2020.03.25.0 Direct Connect (1).JPG Direct Connect (2).JPG DIRECT CONNECT XMit 2020.03.25.0 Direct Connect (3).JPG Direct Connect (4).JPG DIRECT CONNECT photo PSA-ESCI 2019.11.08.1 photos PSA-ESCI 2019.11.08.1 SE (1).JPG SE (2).JPG -2 SPURIOUS RADIATED EMISSIONS Report No. PRCO01132/7 photo PSA-ESCI 2019.11.08.1 photos PSA-ESCI 2019.11.08.1 SE (3).JPG SE (4).JPG -4 SPURIOUS RADIATED EMISSIONS Report No. PRCO01133/7 photo PSA-ESCI 2019.11.08.1 photos PSA-ESCI 2019.11.08.1 SE (5).JPG SE (6).JPG -6 SPURIOUS RADIATED EMISSIONS Report No. PRCO01134/7 photo PSA-ESCI 2019.11.08.1 photos PSA-ESCI 2019.11.08.1 SE (7).JPG SE (8).JPG -8 SPURIOUS RADIATED EMISSIONS Report No. PRCO01135/7 SPURIOUS RADIATED EMISSIONS photo PSA-ESCI 2019.11.08.1 photos PSA-ESCI 2019.11.08.1 SE less than 1000, FCC (1).JPG SE less than 1000, FCC (2).JPG less than 1000, FCC (2) Report No. PRCO01136/7