OZ5URCMRX4SENSensor Extender

Order Number : GETEC-C1-1 3-116 FCC Part 15 subpart C Test Report Number : GETEC-E3-1 3-030 Page 1 / 1 EUT Type: Sensor Extender FCC ID.: OZ5URCMRX4SEN APPENDIX H : USER’S MANUAL MRX-4SEN Sensor Extender Owners Manual MRX-4SEN Sensor Extender Owners Manual ©2013 Universal Remote Control, Inc. The information in this manual is copyright protected. No part of this manual may be copied or reproduced in any form without prior written consent from Universal Remote Control, Inc. UNIVERSAL REMOTE CONTROL, INC. SHALL NOT BE LIABLE FOR OPERATIONAL, TECHNICAL OR EDITORIAL ERRORS/OMISSIONS MADE IN THIS MANUAL. The information in this manual may be subject to change without prior notice. Total Control is a registered trademark of Universal Remote Control, Inc. All other brand or product names are trademarks or registered trademarks of their respective companies or organizations. 500 Mamaroneck Avenue, Harrison, NY 10528 Phone: (914) 835-4484 Fax: (914) 835-4532 TABLEOFCONTENTS Introduction1 Features and Benefits1 Parts Guide1 Front, Rear, and Bottom Panel Descriptions2 Network Installation5 Specifications6 USA Limited Warranty Statement7 Federal Communication Commission Interference Statement9 Declaration of Conformity10 MRX-4SEN SENSOREXTENDER Introduction Thank you for purchasing the MRX-4SEN Sensor Extender. Expand your MRX Advanced Network System Controller sensor coverage beyond four ports by adding additional MRX-4SEN units throughout the home or office. Features and Benefits •Expand Sensor Coverage Add one or more MRX-4SEN throughout your home or office to detect changes in a connected sensor, which may be used to trigger system events. • No Cables, No Mess, No Fuss Connect a MRX-4SEN virtually anywhere in the home or office without the mess of cables while communicating over URC’s 2.4GHz wireless connection. • Compact Size The small size of the MRX-4SEN allows it to easily fit behind equipment or into places where a traditional base station would not. Page 1 Parts Guide The MRX-4SEN includes: 1 - MRX-4SEN Sensor Extender 1 - AC Power Adapter 4 - Mounting Screws 1 - Mounting Plate 1 - Owner’s Manual Page 2 MRX-4SEN SENSOREXTENDER Front, Rear, and Bottom Panel Descriptions Front Panel The front panel consists of 3 indicator lights: Power LED: The Power LED illuminates when the unit is powered. Status LED:The Status LED color will vary depending upon its connected state: ●Connected: Illuminates green ●Low Signal: Illuminates orange ●Not Connected: Not illuminated Data LED: The Data LED flashes as the MRX-4SEN transmits data to a MRX Advanced Network System Controller. Page 3 Rear Panel The rear panel consists of: DC 12V Power:Plug in the included 12V DC 1A power supply. Sensor Inputs: Connect the sensor’s 3.5mm plug to an available port. The following URC sensors, with their respective model numbers, are compatible with the MRX-4SEN: ● Voltage Sensor SEN-VOLT ●Video Sensor SEN-VID ●Contact Closure Sensor SEN-CCLS ●Light Sensor SEN-LITE ●Current Sensor (Magnetic Field) SEN-CMF ● Audio Sensor SEN-AUD Mini-USB connector: For future firmware upgrade use! MRX-4SEN SENSOREXTENDER Page 4 MRX-4SEN SENSOREXTENDER Bottom Panel The bottom panel consists of: MAC Address Sticker: The MAC Address (16 characters) identifies this wireless device when connected to the network. Serial Number Sticker:The serial number, located at the bottom of the unit, uniquely identifies the product. Test button: Press to test the signal strength between the MRX Advanced Network System Controller and the MRX-4SEN. While testing, the Status LED will update and display its current connection setting. (Refer to page 2 for Status LED information.) Reset button: Turns the unit OFF then ON again, and reconnects to the URC 2.4GHz RF signal. Page 5 Network Installation WARNING!! Before proceeding, a Custom Professional is required to install and configure your MRX-4SEN. Connect the 3.5mm sensor plug to the rear of the MRX-4SEN. When a change is sensor is detected, the MRX-4SEN sends a signal to the MRX Advanced Network System Controller and triggers a series of commands. The example below showcases a voltage sensor connected to the home’s front door and the MRX-4SEN. Whenever the door bell is pressed, a signal is sent over URC’s RF 2.4GHz to the MRX Advanced Network System Controller. The MRX unit, previously programmed by the Custom Professional, will trigger a series of commands or an event to gain your attention. A programmed event, such as Watch Movie/TV, may pause the movie, mute the audio and display the front door’s video camera. MRX-4SEN SENSOREXTENDER Page 6 MRX-4SEN SENSOREXTENDER Specifications Sensor :Four sensor supports Video, Current, Contact Closure, Ambient Light, Audio, Voltage Sensing via URC sensors. USB :Mini_USB for future firmware upgrade use. RF Range(radio frequency) : 50 to 100 feet, depending upon the environment RF Frequency :2.405 ~ 2.480 GHz Weight : 2.98oz Size : 3.74” X 2.7” X 1.1” Power : 12V DC 1A Page 7 MRX-4SEN SENSOREXTENDER USA Limited Warranty Statement Your Universal Remote Control, when delivered to you in new condition, is warranted against defects in materials or workmanship as follows: UNIVERSAL REMOTE CONTROL, INC.warrants this product against defects in material or workmanship for a period of one (1) year and as set forth below. Universal Remote Control will, at its sole option, repair the product using new or comparable rebuilt parts, or exchange the product for a comparable new or rebuilt product. In the event of a defect, these are your exclusive remedies. This Limited Warranty covers only the hardware components packaged with the Product. It does not cover technical assistance for hardware or software usage and it does not cover any software products whether or not contained in the Product; any such software is provided "AS IS" unless expressly provided for in any enclosed software Limited Warranty. To obtain warranty service, you must deliver the product, freight prepaid, in its origin…

Text truncated - open the document above for the full version.

SCS-F18: Project and Product Certification Representative Authorization Letter Page 2 of 2 Rev 2.0 OHSUNG ELECTRONICS CO., LTD #181 Gongdan-Dong, Gumi-Si,Gyeongsangbuk-Do, Korea Tel: +82-54-468-7282, Fax: +82-54-461-8368 April 3, 2013 To: SIEMIC, INC. 775 Montague Expressway, Milpitas, CA95035 USA Dear Sir/Madam, Re: Project and Product Certification Representative Authorization Letter We, OHSUNG ELECTRONICS CO., LTD, hereby authorize SIEMIC, INC. to act as a Certification Body for certifying for the following project(s): Product Name: Base Station FCC ID: OZ5URCMRX4SEN We affirm that between SIEMIC and OHSUNG ELECTRONICS CO., LTD, any difference in understanding, including test plan, measurement methods, applicable standards and relevant procedures and processes have been resolved prior to commencement of testing activities. Sincerely, --------------------------------------------- Hak-Ki Kim, Q.C Manager OHSUNG ELECTRONICS CO.,LTD

OHSUNG ELECTRONICS CO., LTD #181 Gongdan-Dong, Gumi-Si,Gyeongsangbuk-Do, Korea Tel: +82-54-468-7282, Fax: +82-54-461-8368 SCS-F19: Confidentiality Request Letter Rev 1.0 Nov 14, 2006 Federal Communications Commission Authorization and Evaluation Division April 3, 2013 Confidentiality Request regarding application for certification of FCC ID: OZ5URCMRX4SEN We hereby request confidential treatment of information accompanying this application as outlined below: Exhibit Type File Name BLOCK DIAGRAM URCMRX4SEN_BlkDia.pdf SCHEMETIC DIAGRAM URCMRX4SEN_SchDia.pdf OPERATIONAL DESCRIPTION URCMRX4SEN_OpeDes.pdf PART LIST URCMRX4SEN_PrtLst.pdf The above materials contain trade secrets and proprietary information not customarily released to the public. The public disclosure of these materials may be harmful to the applicant and provide unjustified benefits to its competitors. In addition to above mentioned documents, pursuant to Public DA 04-1705 of the Commission’s policy, in order to comply with the marketing regulations in 47 CFR 2.803 and the importation rules in 47 CFR 2.1204, while ensuring that business sensitive information remains confidential until the actual marketing of newly authorized devices. We are requesting the commission to grant short-term confidentiality request on the following for 180 day. Exhibit Type File Name TEST SET UP PHOTOS URCMRX4SEN_Tsup.pdf EXTERNAL PHOTOGRAPHS URCMRX4SEN_ExtPho.pdf INTERNAL PHOTOGRAPHS URCMRX4SEN_IntPho.pdf USER’S MANUAL URCMRX4SEN_UseMan.pdf The applicant understands that pursuant to Section 0.457 & 0.459 of the Rules, disclosure of this application and all accompanying documentation will not be made before the date of the Grant for this application. Sincerely, --------------------------------------------- Hak-Ki Kim, Q.C Manager OHSUNG ELECTRONICS CO., LTD

     #181 Gongdan-Dong, Gumi-Si,Gyeongsangbuk-Do, Korea Tel: +82-54-468-7282, Fax: +82-54-461-8368    !" ## $% !"&! '()*+,  -,.'/(0   March 4, 2013  -34  %%56* MRX4SEN   :!;!-2!5!<<%%2!5 52%!&%%%!%5!%5;   2     ============================================= +=>>? ,;      GG

February 14, 2013 Federal Communications Commission Authorization and Evaluation Division Equipment Authorization Branch 7435 Oakland Mills Road Columbia, MD 21046 U.S.A. To whom it may concern: We, the undersigned, hereby authorize GUMI College EMC Center to act on our behalf in all matters relating to applications for equipment authorization, including the signing of all documents relation to these matters. Any and all acts carried out by GUMI College EMC Center on our behalf shall have the same effect as acts of our own. We also hereby certify that no party to the application is subject of a denial of benefits, including FCC benefits, pursuant 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C. 853(a). Sincerely, HAK-KI, KIM / General Manager OHSUNG ELECTRONICS CO., LTD. G

Order Number : GETEC-C1-1 3-116 FCC Part 15 subpart C Test Report Number : GETEC-E3-1 3-030 Page 1 / 6 EUT Type: Sensor Extender FCC ID.: OZ5URCMRX4SEN APPENDIX F : EXTERNAL PHOTOGRAPHS Order Number : GETEC-C1-1 3-116 FCC Part 15 subpart C Test Report Number : GETEC-E3-1 3-030 Page 2 / 6 EUT Type: Sensor Extender FCC ID.: OZ5URCMRX4SEN < Front > Order Number : GETEC-C1-1 3-116 FCC Part 15 subpart C Test Report Number : GETEC-E3-1 3-030 Page 3 / 6 EUT Type: Sensor Extender FCC ID.: OZ5URCMRX4SEN < Rear > Order Number : GETEC-C1-1 3-116 FCC Part 15 subpart C Test Report Number : GETEC-E3-1 3-030 Page 4 / 6 EUT Type: Sensor Extender FCC ID.: OZ5URCMRX4SEN < I/O port > Order Number : GETEC-C1-1 3-116 FCC Part 15 subpart C Test Report Number : GETEC-E3-1 3-030 Page 5 / 6 EUT Type: Sensor Extender FCC ID.: OZ5URCMRX4SEN < Adapter > Order Number : GETEC-C1-1 3-116 FCC Part 15 subpart C Test Report Number : GETEC-E3-1 3-030 Page 6 / 6 EUT Type: Sensor Extender FCC ID.: OZ5URCMRX4SEN < Adapter label >

Order Number : GETEC-C1-1 3-116 FCC Part 15 subpart C Test Report Number : GETEC-E3-1 3-030 Page 1 / 2 EUT Type: Sensor Extender FCC ID.: OZ5URCMRX4SEN APPENDIX B : ID SAMPLE LABEL & LOCATION Order Number : GETEC-C1-1 3-116 FCC Part 15 subpart C Test Report Number : GETEC-E3-1 3-030 Page 2 / 2 EUT Type: Sensor Extender FCC ID.: OZ5URCMRX4SEN LABELLING REQUIREMENTS The label shown shall be permanently affixed at a conspicuous location on the device and be readily visible to the user at the time of purchase.  ID Label  ID Label Location of EUT ID Label

Order Number : GETEC-C1-1 3-116 FCC Part 15 subpart C Test Report Number : GETEC-E3-1 3-030 Page 1 / 6 EUT Type: Sensor Extender FCC ID.: OZ5URCMRX4SEN APPENDIX G : INTERNAL PHOTOGRAPHS Order Number : GETEC-C1-1 3-116 FCC Part 15 subpart C Test Report Number : GETEC-E3-1 3-030 Page 2 / 6 EUT Type: Sensor Extender FCC ID.: OZ5URCMRX4SEN < Inside > Order Number : GETEC-C1-1 3-116 FCC Part 15 subpart C Test Report Number : GETEC-E3-1 3-030 Page 3 / 6 EUT Type: Sensor Extender FCC ID.: OZ5URCMRX4SEN < Main board front > Order Number : GETEC-C1-1 3-116 FCC Part 15 subpart C Test Report Number : GETEC-E3-1 3-030 Page 4 / 6 EUT Type: Sensor Extender FCC ID.: OZ5URCMRX4SEN < Main board rear > Order Number : GETEC-C1-1 3-116 FCC Part 15 subpart C Test Report Number : GETEC-E3-1 3-030 Page 5 / 6 EUT Type: Sensor Extender FCC ID.: OZ5URCMRX4SEN < RF module front > RF Antenna Order Number : GETEC-C1-1 3-116 FCC Part 15 subpart C Test Report Number : GETEC-E3-1 3-030 Page 6 / 6 EUT Type: Sensor Extender FCC ID.: OZ5URCMRX4SEN < RF module rear >

Order Number : GETEC-C1-1 3-116 FCC Certification Test Report Number : GETEC-E3-1 3-030 Page 1 / 3 EUT Type: Sensor Extender FCC ID.: OZ5URCMRX4SEN APPENDIX L : MAXIMUM PERMISSIBLE EXPOSURE Order Number : GETEC-C1-1 3-116 FCC Certification Test Report Number : GETEC-E3-1 3-030 Page 2 / 3 EUT Type: Sensor Extender FCC ID.: OZ5URCMRX4SEN Maximum Permissible Exposure 1.1 Applicable Standard Systems operating under the provisions of this section shall be operated in a manner that ensures that the public is not exposed to radio frequency energy levels in excess limit for maximum permissible exposure. In accordance with 47 CFR FCC Part 2 Subpart J, section 2.1091 this device has been defined as a mobile device whereby a distance of 0.2 m normally can be maintained between the user and the device (A) Limits for Occupational / Controlled Exposure Frequency range(MHz) Electric Field Strength (E) (V/m) Magnetic Field Strength (H) (A/m) Power Density(S) (mW/cm2) Averaging Time |E|2, |H|2 or S (minutes) 0.3 ~ 3.0 614 1.63 (100)* 6 3.0~30 1842/f 4.89/f (900/f)* 6 30~300 61.4 0.163 1.0 6 300 ~ 1,500 f/300 6 1,500 ~ 100,000 5.0 6 (B) Limits for General Population / Uncontrolled Exposure Frequency range(MHz) Electric Field Strength (E) (V/m) Magnetic Field Strength (H) (A/m) Power Density(S) (mW/cm2) Averaging Time |E|2, |H|2 or S (minutes) 0.3 ~ 1.34 614 1.63 (100)* 30 1.34 ~ 30 824/f 2.19/f (180/f)* 30 30~ 300 27.5 0.073 0.2 30 300 ~ 1,500 f/1500 30 1,500 ~ 100,000 1.0 30 Note: f=frequency in MHz; *Plane-wave equivalent power density 1.2 MPE Calculation Method d GP mVE ×× = 30 )/( Power Density: 377 )/( 2 2 E mWPd= E = Electric field (V/m) P = Peak RF output power (W) G = EUT Antenna numeric gain (numeric) d = Separation distance between radiator and human body (m) The formula can be changed to 2 377 30 d GP Pd × ×× = From the peak EUT RF output power, the minimum mobile separation distance, d=0.2m, as well as the gain of the used antenna, the RF power density can be obtained. Order Number : GETEC-C1-1 3-116 FCC Certification Test Report Number : GETEC-E3-1 3-030 Page 3 / 3 EUT Type: Sensor Extender FCC ID.: OZ5URCMRX4SEN 1.3 Calculated Result and Limit Antenna type: chip antenna Antenna gain (dBi) Antenna gain (numeric) Peak output power (dBm) Peak output power (mW) Power Density (s) (mW/cm 2 ) Limit of Power density (S) (mW/cm 2 ) 3.05 2.02 16.31 42.76 0.017 1

nnERFL잃많$GE pagc 1 orJ 1 FCCEν4L UA TION REPORT FOR CERTIFICATION Manufacturer: OHSUNG ELECTRONICS CO., LTD. #141 Gongdan-dong , Gumi-si, Gyeongbuk, RepubJic of Korea Attn: Mr. Hak-Ki Kim I General Manager Date of Issue: Aprill ,2013 Order Number: GETEC-CI-13-116 Test Report Number: GETEC-E3-13-030 Test Site: GUMI COLLEGE EMC CENTER FCC Registration Number: (100749,443957) FCC ID_ 0Z5URCMRX4SEN Applicant : Rule Part(s) Test Method Equipment Class EUTType Type of Authority Model Name Trade Name OHSUNG ELECTRONICS CO_, LTD. : FCC Part 15 Subpart C-1ntentional Radiator ~ 15.247 : ANSI C63.1O (2009) : Digital Tγansmission System(DTS) : Sensor Extender : Certification : MRX-4SEN : UNIVERSAL Remote Control This equipment has been shown to be in compliance with tbe applicable tecbnical standards as indicated in the measurement report and was tested in accordance with the measurement procedures specified in ANSI C63.4 (2009) 1 attest to the accuracy of data. AII measurements reported herein were performed by me or were made under my supeπision and are correct to the vest of my knowledge and beJief. 1 assume full responsibility for the completeness of tbese measurements and vouch for tbe qualifications of all persons taking them. Tested by, ?~ Seung'::thul Lee, Senior Engineer GUMI COLLEGE EMC CENTER GETEC-QP-28-007 (Rev.Ol ) Reviewed by , Jae-Hoon Jeong, ;recbnical Manager GUMI COLLEGE EMC CENTER EMC CENTER rhis 1εstrεport only contains thζ result ofa specific sample supplied f or the examination It is not allowed t o copy this report even partly without the approval of EMC center 壘聽魔줬~ Order Number : GETEC-C1-13-116 FCC Part 15 Subpart C Test Report Number: GETEC-E3-13-030 Page2 / 31 EUT Type: Sensor Extender FCC ID.: OZ5URCMRX4SEN G E TEC CONTENTS 1. GENERAL INFORMATION ...................................................................................................................................... 4 2. INTRODUCTION ........................................................................................................................................................ 5 3. PRODUCT INFORMATION ...................................................................................................................................... 6 3.1 DESCRIPTION OF EUT .............................................................................................................................................. 6 3.2 SUPPORT EQUIPMENT / CABLES USED ..................................................................................................................... 7 3.3 MODIFICATION ITEM(S) ........................................................................................................................................... 7 4. DESCRIPTION OF TESTS ......................................................................................................................................... 8 4.1 TEST CONDITION ...................................................................................................................................................... 8 5. ANTENNA REQUIREMENT - §15.203 ..................................................................................................................... 8 5.1 DESCRIPTION OF ANTENNA ...................................................................................................................................... 8 5.2 CONDUCTED EMISSION ............................................................................................................................................ 9 5.3 RADIATED EMISSION .............................................................................................................................................. 10 6. CONDUCTED EMISSION ........................................................................................................................................ 11 6.1 OPERATING ENVIRONMENT ................................................................................................................................... 11 6.2 TEST SET-UP ........................................................................................................................................................... 11 6.3 MEASUREMENT UNCERTAINTY.............................................................................................................................. 11 6.4 LIMIT ...................................................................................................................................................................... 12 6.5 TEST EQUIPMENT USED .......................................................................................................................................... 12 6.6 TEST DATA FOR CONDUCTED EMISSION ................................................................................................................ 12 7. MAXIMUM PEAK OUTPUT POWER MEASUREMENT .................................................................................. 14 7.1 OPERATING ENVIRONMENT ................................................................................................................................... 14 7.2 TEST SET-UP (LAYOUT) .......................................................................................................................................... 14 7.3 LIMIT ...................................................................................................................................................................... 14 7.4 TEST EQUIPMENT USED .......................................................................................................................................... 14 7.5 TEST RESULT .......................................................................................................................................................... 14 8. POWER SPECTRAL DENSITY MEASUREMENT ............................................................................................…

Text truncated - open the document above for the full version.

Order Number : GETEC-C1-1 3-116 FCC Part 15 subpart C Test Report Number : GETEC-E3-1 3-030 Page 1 / 4 EUT Type: Sensor Extender FCC ID.: OZ5URCMRX4SEN APPENDIX E : TEST SET UP PHOTOGRAPHS Order Number : GETEC-C1-1 3-116 FCC Part 15 subpart C Test Report Number : GETEC-E3-1 3-030 Page 2 / 4 EUT Type: Sensor Extender FCC ID.: OZ5URCMRX4SEN  Conducted Test Picture (Front)  Conducted Test Picture (Rear) Order Number : GETEC-C1-1 3-116 FCC Part 15 subpart C Test Report Number : GETEC-E3-1 3-030 Page 3 / 4 EUT Type: Sensor Extender FCC ID.: OZ5URCMRX4SEN  Radiated Test Picture (Front): Below 30 MHz  Radiated Test Picture (Rear): Below 1 GHz Order Number : GETEC-C1-1 3-116 FCC Part 15 subpart C Test Report Number : GETEC-E3-1 3-030 Page 4 / 4 EUT Type: Sensor Extender FCC ID.: OZ5URCMRX4SEN  Radiated Test Picture (Front): Above 1 GHz