OZ5URCZR1NZigbee Repeater

G Order Number : GETEC-C1-11-239 FCC Part 15 subpart C Test Report Number : GETEC-E3-11-122 Page 1 / 1 EUT Type: Zigbee Repeater FCC ID.: OZ5URCZR1N APPENDIX H : USER’S MANUAL ZR-1N Z Repeater Owner’s Manual ZR-1N Z Repeater Owner’s Manual ©2010 Universal Remote Control, Inc. The information in this manual is copyright protected. No part of this manual may be copied or reproduced in any form without prior written consent from Universal Remote Control, Inc. UNIVERSAL REMOTE CONTROL, INC. SHALL NOT BE LIABLE FOR OPER- ATIONAL, TECHNICAL OR EDITORIAL ERRORS/OMISSIONS MADE IN THIS MANUAL. The information in this manual may be subject to change without prior notice. URC - Control the Experience is a registered trademark of Universal Remote Control, Inc. All other brand or product names are trademarks or registered trademarks of their respective companies or organizations. 500 Mamaroneck Avenue, Harrison, NY 10528 Phone: (914) 835-4484 Fax: (914) 835-4532 TABLE OFCONTENTS Introduction1 Features and Benefits1 Parts Guide1 ZR-1N Front and Side Panel Descriptions2 Specifications3 USA Limited Warranty Statement3 Federal Communication Commission Interference Statement5 Regulatory Information to the user6 Declaration of Conformity7 Page 1 ZR-1N Z REPEATER Introduction Congratulations on your purchase of the ZR-1N Z Repeater! The ZR-1N is used to extend the operational range between Total Control products such as the TRC-780 and the MRX-10. Once joined to the MRX-10 it will wirelessly relay communication between an TRC-780 and another ZR-1N repeater. Features and Benefits Wirelessly extends the range between Total Control products. Extend the operational range between a TRC-780 remote and a MRX-10 Advanced Network System Controller. Control lighting, music and more from through- out the home. Parts Guide The ZR-1N Z Repeater includes: 1 - ZR-1N Z Repeater1 - AC Power Adapter 1 - Wall Mount and 4 Screws1 - Owner’s Manual Page 2 ZR-1N Z REPEATER ZR-1N Front and Side Panel Descriptions The front panel consists of 3 indicator lights which will illuminate when in use. Power LED: Indicates that the ZR-1N is powered on when illuminated. Status LED: The LED will show what the RF signal strength of the ZR-1N to the MRX-10. By pressing the TEST button on the side of the unit, it will indicate the signal strength. When the LED is: . OFF: The ZR-1N is not testing for signal strength, and the TEST button should be pressed. . Orange: The signal strength is LOW, and the ZR-1N should be move to a different location . Green: The signal strength is GOOD, and the ZR-1N is in a good location. Data LED: The LED will flash RED when the unit is transmitting or receiving data. Antenna: Omnidirectional antenna. Adjust the antenna for best per- formance. Usually vertical positioning works well. DC9V Power: Attach the included 9V DC power supply here. Mounting Plate: May be attached to a wall or other surface with the included screws for easy slide on/off mounting. POWER LED STATUS LED USB DC9V Power TEST Mounting Plate Antenna DATA LED Page 3 Specifications RF Frequency:2.48GHz (Two-way RF) Effective Range:Typically 50-75 ft, depending on environment Size:L x D x H = 3.625" x 1.125" x 6.625" (with antenna vertical) Weight:3 oz. Power Supply:9V DC 300mA USA Limited Warranty Statement Your Universal Remote Control, when delivered to you in new con- dition, is warranted against defects in materials or workmanship as follows: UNIVERSAL REMOTE CONTROL, INC.warrants this prod- uct against defects in material or workmanship for a period of one (1) year and as set forth below. Universal Remote Control will, at its sole option, repair the product using new or comparable rebuilt parts, or exchange the product for a comparable new or rebuilt product. In the event of a defect, these are your exclusive remedies. This Limited Warranty covers only the hardware components pack- aged with the Product. It does not cover technical assistance for hardware or software usage and it does not cover any software products whether or not contained in the Product; any such soft- ware is provided "AS IS" unless expressly provided for in any enclosed software Limited Warranty. To obtain warranty service, you must deliver the product, freight prepaid, in its original packaging or packaging affording adequate protection to Universal Remote Control at the address provided in the Owner's Manual. It is your responsibility to backup any macro programming, artwork, software or other materials that may have been programmed into your unit. It is likely that such data, soft- ware, or other materials will be lost during service and Universal Remote Control will not be responsible for any such damage or loss.A dated purchase receipt, Bill of Sale, Installation Contract or other verifiable Proof of Purchase is required. For product support and other important information visit Universal Remote Control's website: http://www .UniversalRemote.comor call the Customer Service Center (914) 835-4484. ZR-1N Z REPEATER Page 4 This Limited Warranty only covers product issues caused by defects in material or workmanship during ordinary consumer use. It does not cover product issues caused by any other reason, including but not limited to product issues due to commercial use, acts of God, third-party installation, misuse, limitations of technology, or modifi- cation of or to any part of the Universal Remote Control product. This Limited Warranty does not cover Universal Remote Control products sold as USED, AS IS, REFURBISHED, so-called “B STOCK” or consumables (such as batteries). This Limited Warranty is invalid if the factory-applied serial number has been altered or removed from the product. This Limited Warranty is valid only in the United States of America. This Limited Warranty specifically excludes products sold by unauthorized resellers. LIMITATION OF REMEDIES UNIVERSAL REMOTE CONTROL SHALL NOT BE LIABLE FOR ANY INCIDENTAL OR CONSEQUENTIAL DAMAGES FOR BREACH OF ANY EXPRE…

Text truncated - open the document above for the full version.

SCS-F18: Project and Product Certification Representative Authorization Letter Page 1 of 2 Rev 2.0 2206 Ringwood Avenue San Jose, CA 95131 Tel: 408-526-1188 Fax: 408-526-1088 Email: [email protected] Project and Product Certification Representative Authorization Letter Reason for Amendment (current / obsolete) Revision History Approved Date From To Initial Release (current) 1.0 1.0 Nov-14-2006 Revised wording (current) 1.0 2.0 Sept–25-2007 SCS-F18: Project and Product Certification Representative Authorization Letter Page 2 of 2 Rev 2.0 OHSUNG ELECTRONICS CO., LTD #181 Gongdan-Dong, Gumi-Si,Gyeongsangbuk-Do, Korea Tel: +82-54-468-7282, Fax: +82-54-461-8368 November 7, 2011 To: SIEMIC, INC. 2206 Ringwood Avenue, San Jose, CA 95131 USA Dear Sir/Madam, Re: Project and Product Certification Representative Authorization Letter We, OHSUNG ELECTRONICS CO., LTD, hereby authorize SIEMIC, INC. to act as a Certification Body for certifying for the following project(s): Product Name: Zigbee Repeater FCC ID: OZ5URCZR1N We affirm that between SIEMIC and OHSUNG ELECTRONICS CO., LTD, any difference in understanding, including test plan, measurement methods, applicable standards and relevant procedures and processes have been resolved prior to commencement of testing activities. Sincerely, --------------------------------------------- Hak-Ki Kim, Q.C Manager OHSUNG ELECTRONICS CO.,LTD

Confidentiality Request Letter Reason for Amendment (current / obsolete) Revision History Approved Date From To Initial Release (current) 1.0 1.0 Nov-14-2006 OHSUNG ELECTRONICS CO., LTD #181 Gongdan-Dong, Gumi-Si,Gyeongsangbuk-Do, Korea Tel: +82-54-468-7282, Fax: +82-54-461-8368 SCS-F19: Confidentiality Request Letter Rev 1.0 Nov 14, 2006 Federal Communications Commission Authorization and Evaluation Division November 7, 2011 Confidentiality Request regarding application for certification of FCC ID: OZ5URCZR1N We hereby request confidential treatment of information accompanying this application as outlined below: Exhibit Type File Name BLOCK DIAGRAM URCZR1N_BlkDia.pdf SCHEMETIC DIAGRAM URCZR1N_SchDia.pdf OPERATIONAL DESCRIPTION URCZR1N_OpeDes.pdf The above materials contain trade secrets and proprietary information not customarily released to the public. The public disclosure of these materials may be harmful to the applicant and provide unjustified benefits to its competitors. In addition to above mentioned documents, pursuant to Public DA 04-1705 of the Commission’s policy, in order to comply with the marketing regulations in 47 CFR 2.803 and the importation rules in 47 CFR 2.1204, while ensuring that business sensitive information remains confidential until the actual marketing of newly authorized devices. We are requesting the commission to grant short-term confidentiality request on the following Exhibit Type File Name TEST SET UP PHOTOS URCZR1N_Tsup.pdf EXTERNAL PHOTOGRAPHS URCZR1N_ExtPho.pdf INTERNAL PHOTOGRAPHS URCZR1N_IntPho.pdf USER’S MANUAL URCZR1N_UseMan.pdf The applicant understands that pursuant to Section 0.457 of the Rules, disclosure of this application and all accompanying documentation will not be made before the date of the Grant for this application. Sincerely, --------------------------------------------- Hak-Ki Kim, Q.C Manager OHSUNG ELECTRONICS CO.,LTD

OHSUNG ELECTRONICS CO., LTD #181 Gongdan-Dong, Gumi-Si,Gyeongsangbuk-Do, Korea Tel: +82-54-468-7282, Fax: +82-54-461-8368 Federal Communications Commission Authorization and Evaluation Division Equipment Authorization Branch 1435 Oakland Mills Road Columbia, MD 21046 U.S.A October 3, 2011 Subject: FCC Application for OZ5URCZR1N We, the undersigned, hereby attest to the fact that we will apply the Declaration of Conformity procedure to the class B computer peripheral portion of this composite filing. Sincerely, --------------------------------------------- Hak-Ki Kim, Q.C Manager OHSUNG ELECTRONICS CO., LTD

Order Number : GETEC-C1-11-239 FCC Part 15 subpart C Test Report Number : GETEC-E3-11-122 Page 1 / 5 EUT Type: Zigbee Repeater FCC ID.: OZ5URCZR1N APPENDIX F : EXTERNAL PHOTOGRAPHS Order Number : GETEC-C1-11-239 FCC Part 15 subpart C Test Report Number : GETEC-E3-11-122 Page 2 / 5 EUT Type: Zigbee Repeater FCC ID.: OZ5URCZR1N < Front > Order Number : GETEC-C1-11-239 FCC Part 15 subpart C Test Report Number : GETEC-E3-11-122 Page 3 / 5 EUT Type: Zigbee Repeater FCC ID.: OZ5URCZR1N < Rear > Order Number : GETEC-C1-11-239 FCC Part 15 subpart C Test Report Number : GETEC-E3-11-122 Page 4 / 5 EUT Type: Zigbee Repeater FCC ID.: OZ5URCZR1N < AC/DC adapter > Order Number : GETEC-C1-11-239 FCC Part 15 subpart C Test Report Number : GETEC-E3-11-122 Page 5 / 5 EUT Type: Zigbee Repeater FCC ID.: OZ5URCZR1N < Adapter label >

Order Number : GETEC-C1-11-239 FCC Part 15 subpart C Test Report Number : GETEC-E3-11-122 Page 1 / 2 EUT Type: Zigbee Repeater FCC ID.: OZ5URCZR1N APPENDIX B : ID SAMPLE LABEL & LOCATION Order Number : GETEC-C1-11-239 FCC Part 15 subpart C Test Report Number : GETEC-E3-11-122 Page 2 / 2 EUT Type: Zigbee Repeater FCC ID.: OZ5URCZR1N LABELLING REQUIREMENTS The label shown shall be permanently affixed at a conspicuous location on the device and be readily visible to the user at the time of purchase.  ID Label  ID Label Location of EUT ID Label

Order Number : GETEC-C1-11-239 FCC Part 15 subpart C Test Report Number : GETEC-E3-11-122 Page 1 / 4 EUT Type: Zigbee Repeater FCC ID.: OZ5URCZR1N APPENDIX G : INTERNAL PHOTOGRAPHS Order Number : GETEC-C1-11-239 FCC Part 15 subpart C Test Report Number : GETEC-E3-11-122 Page 2 / 4 EUT Type: Zigbee Repeater FCC ID.: OZ5URCZR1N < Inside > Order Number : GETEC-C1-11-239 FCC Part 15 subpart C Test Report Number : GETEC-E3-11-122 Page 3 / 4 EUT Type: Zigbee Repeater FCC ID.: OZ5URCZR1N < RF & Power board front > RF part Order Number : GETEC-C1-11-239 FCC Part 15 subpart C Test Report Number : GETEC-E3-11-122 Page 4 / 4 EUT Type: Zigbee Repeater FCC ID.: OZ5URCZR1N < RF & Power board front >

Order Number : GETEC-C1-11-239 FCC Certification Test Report Number : GETEC-E3-11-122 Page 1 / 3 EUT Type: Zigbee Repeater FCC ID.: OZ5URCZR1N APPENDIX L : MAXIMUM PERMISSIBLE EXPOSURE Order Number : GETEC-C1-11-239 FCC Certification Test Report Number : GETEC-E3-11-122 Page 2 / 3 EUT Type: Zigbee Repeater FCC ID.: OZ5URCZR1N Maximum Permissible Exposure 1.1 Applicable Standard Systems operating under the provisions of this section shall be operated in a manner that ensures that the public is not exposed to radio frequency energy levels in excess limit for maximum permissible exposure. In accordance with 47 CFR FCC Part 2 Subpart J, section 2.1091 this device has been defined as a mobile device whereby a distance of 0.2 m normally can be maintained between the user and the device (A) Limits for Occupational / Controlled Exposure Frequency range(MHz) Electric Field Strength (E) (V/m) Magnetic Field Strength (H) (A/m) Power Density(S) (mW/cm2) Averaging Time |E|2, |H|2 or S (minutes) 0.3 ~ 3.0 614 1.63 (100)* 6 3.0~30 1842/f 4.89/f (900/f)* 6 30~300 61.4 0.163 1.0 6 300 ~ 1,500 f/300 6 1,500 ~ 100,000 5.0 6 (B) Limits for General Population / Uncontrolled Exposure Frequency range(MHz) Electric Field Strength (E) (V/m) Magnetic Field Strength (H) (A/m) Power Density(S) (mW/cm2) Averaging Time |E|2, |H|2 or S (minutes) 0.3 ~ 1.34 614 1.63 (100)* 30 1.34 ~ 30 824/f 2.19/f (180/f)* 30 30~ 300 27.5 0.073 0.2 30 300 ~ 1,500 f/1500 30 1,500 ~ 100,000 1.0 30 Note: f=frequency in MHz; *Plane-wave equivalent power density 1.2 MPE Calculation Method d GP mVE   30 )/( Power Density: 377 )/( 2 2 E mWPd E = Electric field (V/m) P = Peak RF output power (W) G = EUT Antenna numeric gain (numeric) d = Separation distance between radiator and human body (m) The formula can be changed to 2 377 30 d GP Pd    From the peak EUT RF output power, the minimum mobile separation distance, d=0.2m, as well as the gain of the used antenna, the RF power density can be obtained. Order Number : GETEC-C1-11-239 FCC Certification Test Report Number : GETEC-E3-11-122 Page 3 / 3 EUT Type: Zigbee Repeater FCC ID.: OZ5URCZR1N 1.3 Calculated Result and Limit Antenna type: dipole antenna Antenna gain (dBi) Antenna gain (numeric) Peak output power (dBm) Peak output power (mW) Power Density (s) (mW/cm 2 ) Limit of Power density (S) (mW/cm 2 ) 2.0 1.58 16.10 40.70 0.013 1

Order Number : GETEC-C1-11-239 FCC Class B Certification Test Report Number : GETEC-E3-11-122 Page 2 / 24 EUT Type: Zigbee Repeater FCC ID.: OZ5URCZR1N CONTENTS 1. GENERAL INFORMATION ...................................................................................................................................... 4 2. INTRODUCTION ........................................................................................................................................................ 5 3. PRODUCT INFORMATION ...................................................................................................................................... 6 3.1 DESCRIPTION OF EUT .............................................................................................................................................. 6 3.2 SUPPORT EQUIPMENT / CABLES USED ..................................................................................................................... 6 3.3 MODIFICATION ITEM(S) ........................................................................................................................................... 6 4. DESCRIPTION OF TESTS ......................................................................................................................................... 7 4.1 TEST CONDITION ...................................................................................................................................................... 7 5. ANTENNA REQUIREMENT - §15.203 ..................................................................................................................... 7 5.1 DESCRIPTION OF ANTENNA ...................................................................................................................................... 7 5.2 CONDUCTED EMISSION ............................................................................................................................................ 8 5.3 RADIATED EMISSION ................................................................................................................................................ 9 6. CONDUCTED EMISSION ........................................................................................................................................ 10 6.1 OPERATING ENVIRONMENT ................................................................................................................................... 10 6.2 TEST SET-UP ........................................................................................................................................................... 10 6.3 MEASUREMENT UNCERTAINTY.............................................................................................................................. 10 6.4 LIMIT ...................................................................................................................................................................... 11 6.5 TEST EQUIPMENT USED .......................................................................................................................................... 11 6.6 TEST DATA FOR CONDUCTED EMISSION ................................................................................................................ 11 7. MAXIMUM PEAK OUTPUT POWER MEASUREMENT .................................................................................. 13 7.1 OPERATING ENVIRONMENT.................................................................................................................................... 13 7.2 TEST SET-UP (LAYOUT) .......................................................................................................................................... 13 7.3 LIMIT ...................................................................................................................................................................... 13 7.4 TEST EQUIPMENT USED .......................................................................................................................................... 13 7.5 TEST RESULT .......................................................................................................................................................... 13 8. POWER SPECTRAL DENSITY MEASUREMENT .............................................................................................. 14 8.1 OPERATING ENVIRONMENT ................................................................................................................................... 14 8.2 TEST SET-UP (LAYOUT) .......................................................................................................................................... 14 8.3 LIMIT ...................................................................................................................................................................... 14 8.4 TEST EQUIPMENT USED .......................................................................................................................................... 14 8.5 TEST RESULT .......................................................................................................................................................... 14 9. 6 DB SPECTRUM BANDWIDTH MEASUREMENT ........................................................................................... 16 9.1 OPERATING ENVIRONMENT.................................................................................................................................... 16 9.2 TEST SET-UP (LAYOUT) .......................................................................................................................................... 16 9.3 LIMIT ...................................................................................................................................................................... 16 9.4 TEST EQUIPMENT USED ..........................................................................................…

Text truncated - open the document above for the full version.

Order Number : GETEC-C1-11-239 FCC Part 15 subpart C Test Report Number : GETEC-E3-11-122 Page 1 / 5 EUT Type: Zigbee Repeater FCC ID.: OZ5URCZR1N APPENDIX E : TEST SET UP PHOTOGRAPHS Order Number : GETEC-C1-11-239 FCC Part 15 subpart C Test Report Number : GETEC-E3-11-122 Page 2 / 5 EUT Type: Zigbee Repeater FCC ID.: OZ5URCZR1N  Conducted Test Picture (Front)  Conducted Test Picture (Rear) Order Number : GETEC-C1-11-239 FCC Part 15 subpart C Test Report Number : GETEC-E3-11-122 Page 3 / 5 EUT Type: Zigbee Repeater FCC ID.: OZ5URCZR1N  Radiated Test Picture (Front): 9 kHz to 30 MHz  Radiated Test Picture (Rear): 9 kHz to 30 MHz Order Number : GETEC-C1-11-239 FCC Part 15 subpart C Test Report Number : GETEC-E3-11-122 Page 4 / 5 EUT Type: Zigbee Repeater FCC ID.: OZ5URCZR1N  Radiated Test Picture (Front): 30 MHz to 1 GHz  Radiated Test Picture (Rear): 30 MHz to 1 GHz Order Number : GETEC-C1-11-239 FCC Part 15 subpart C Test Report Number : GETEC-E3-11-122 Page 5 / 5 EUT Type: Zigbee Repeater FCC ID.: OZ5URCZR1N  Radiated Test Picture (Front): Above 1 GHz  Radiated Test Picture (Rear): Above 1 GHz