OZWKAREL-IPV10IP PBX

IP PBX TECHNICAL REFERENCE & INSTALLATION GUIDE 05/06/2012 TECHNICAL REFERENCE & INSTALLATION GUIDE II TECHNICAL REFERENCE & INSTALLATION GUIDE III CAUTION SINCE IPV50 SERIES IP TELEPHONE EXCHANGES ARE ELECTRONIC-BASED PRODUCTS, THE REQUIREMENTS BELOW SHOULD BE FULFILLED IN ORDER TO UTILIZE IT WITH DESIRED PERFORMANCE: The system covers must not be opened by unauthorized persons in any way. The cover of the exchange cabinet should always be kept closed. All the ground connections on the covers must be fixed and checked before closing all the covers of the system. Precautions must be taken in order to prevent any harmful substances from leaking or spilling into the exchange in any way. Serious hazards may occur unless the conditions above are matched completely! TECHNICAL REFERENCE & INSTALLATION GUIDE IV CAVEAT This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Any Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: --Reorient or relocate the receiving antenna. --Increase the separation between the equipment and receiver. --Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. --Consult the dealer or an experienced radio/TV technician for help. TECHNICAL REFERENCE & INSTALLATION GUIDE V CUSTOMER INFORMATION 1. This equipment complies with Part 68 of the FCC rules and the requirements adopted by the ACTA. On the bottom of this equipment is a label that contains, among other information, a product identifier in the format US: UL7IS00BIPV10. If requested, this number must be provided to the telephone company. 2. A plug and jack used to connect this equipment to the premises wiring and telephone network must comply with the applicable FCC Part 68 rules and requirements adopted by the ACTA. A compliant telephone cord and modular plug is provided with this product. It is designed to be connected to a compatible modular jack that is also compliant. See installation instructions for details. 3. If this equipment [Karel IP PBX IPV10] causes harm to the telephone network, the telephone company will notify you in advance that temporary discontinuance of service may be required. But if advance notice isn't practical, the telephone company will notify the customer as soon as possible. Also, you will be advised of your right to file a complaint with the FCC if you believe it is necessary. 4. The telephone company may make changes in its facilities, equipment, operations or procedures that could affect the operation of the equipment. If this happens the telephone company will provide advance notice in order for you to make necessary modifications to maintain uninterrupted service. 5. If trouble is experienced with this equipment [US: UL7IS00BIPV10], for repair or warranty information, Service can be facilitated through our office at: U.S. Agent Company name: RONCO COMMUNICATIONS Address: 84 Grand Island Blvd Tonawanda, NY 14150 Tel: 716-873-0760 Fax: 716-879-8189 If the equipment is causing harm to the telephone network, the telephone company may request that you disconnect the equipment until the problem is resolved. Please check if KAREL has office or agent at USA to provide the repair or warranty services? If not then, you can just provide the office at Turkey or other country. 6. Connection to party line service is subject to state tariffs. Contact the state public utility commission, public service commission or corporation commission for information. 7. If your home has specially wired alarm equipment connected to the telephone line, ensure the installation of this [US: UL7IS00BIPV10] does not disable your alarm equipment. If you have questions about what will disable alarm equipment, consult your telephone company or a qualified installer. 8. If the telephone company requests information on what equipment is connected to their lines, inform them of: a) The ringer equivalence number [0.0B] TECHNICAL REFERENCE & INSTALLATION GUIDE VI b) The USOC jack required [RJ11C] c) Facility Interface Codes (“FIC”) [METALLIC] d) Service Order Codes (“SOC”) [9.0y] e) The FCC Registration Number [US: UL7IS00BIPV10] 9. The REN is used to determine the number of devices that may be connected to a telephone line. Excessive RENs on a telephone line may result in the devices not ringing in response to an incoming call. In most but not all areas, the sum of RENs should not exceed five (5.0). To be certain of the number of devices that may be connected to a line, as determined by the total RENs, contact the local telephone company. The REN for this product is part of the product identifier that has the format US: AAAEQ##TXXXX. The digits represented by ## are the REN without a decimal point. For this product the FCC Registration number is [US: UL7IS00BIPV10] indicates the REN would be 0.0B. 10. If this product is equipped with a corded or cordless handset, it is hearing aid comp…

Text truncated - open the document above for the full version.

1234 A B C D 4 321 D C B A Title NumberRevisionSize A4 Date:26-Dec-2012Sheet of File:D:\E\SCH\MA04.ddbDrawn By: RJ45 Reset 12VDC BRI and PSTN Interface MAC + PHY BRI module and CPLD CPU:BF533 SPI,TDM SPI DC-DC 3.3V DC-DC 5V DC-DC VDDINT NAND FlashSDRAMSPI Flash SPI RS232 RTC 25MHz Encryption 2.048MHz PSTN module 32.768KHZ

EXHIBIT B - EUT EXTERNAL PHOTOGRAPHS EUT – All View EUT – Top View EUT – Bottom View EUT – Left View EUT – Right View EUT – Port View EUT – Adapter View EUT – Adapter Label View

EXHIBIT A - FCC ID LABELING AND LOCATION FCC ID Label Proposed FCC ID Location

EXHIBIT C - EUT INTERNAL PHOTOGRAPHS EUT – Uncover View EUT – FXO Board Top View UT – FXO Board Bottom View EUT – FXS Board Top View EUT – FXS Board Bottom View EUT – Main Board Top View EUT – Main Board Bottom View EUT – Battery Top View EUT – Battery Bottom View

Note: This test report is prepared for the customer shown above and for the device described herein. It may not be duplicated or used in part without prior written consent from Bay Area Compliance Laboratories Corp. (Dongguan). FCC PART 15B, CLASS B TEST REPORT For KAREL ELEKTRONIK SANAYI VE TICARET A.S. Kore Sehitleri Caddesi, Yuzbasi Kaya Aldogan Sok. No: 16 Zincirlikuyu / Istanbul 34394, Turkey Report Type: Original Report Product Type: IP PBX Test Engineer: Star Xie Report Number: R1XM120806050-00 Report Date: 2012-12-26 Reviewed By: Harry Wu EMC Leader Test Laboratory: Bay Area Compliance Laboratories Corp. (Dongguan) No.69 Pulongcun, Puxinhu Industrial Zone, Tangxia, Dongguan, Guangdong, China Tel: +86-769-86858888 Fax: +86-769-86858891 www.baclcorp.com.cn FCC ID: OZWKAREL-IPV10 Bay Area Compliance Laboratories Corp. (Dongguan) Report No.: R1XM120806050-00 FCC Part15B, Class B Page 2 of 17 TABLE OF CONTENTS GENERAL INFORMATION ....................................................................................................................................... 3 PRODUCT DESCRIPTION FOR EQUIPMENT UNDER TEST (EUT) ..................................................................................... 3 OBJECTIVE ................................................................................................................................................................... 3 RELATED SUBMITTAL(S)/GRANT(S) ............................................................................................................................. 3 TEST FACILITY ............................................................................................................................................................. 3 SYSTEM TEST CONFIGURATION .......................................................................................................................... 4 JUSTIFICATION ............................................................................................................................................................. 4 EUT EXERCISE SOFTWARE .......................................................................................................................................... 4 EQUIPMENT MODIFICATIONS ....................................................................................................................................... 4 LOCAL SUPPORT EQUIPMENT LIST AND DETAILS ........................................................................................................ 4 EXTERNAL I/O CABLE .................................................................................................................................................. 4 BLOCK DIAGRAM OF TEST SETUP ................................................................................................................................ 5 SUMMARY OF TEST RESULTS ............................................................................................................................... 6 FCC §15.107 – AC LINE CONDUCTED EMISSIONS ............................................................................................. 7 MEASUREMENT UNCERTAINTY .................................................................................................................................... 7 EUT SETUP .................................................................................................................................................................. 7 EMI TEST RECEIVER SETUP ......................................................................................................................................... 7 TEST PROCEDURE ........................................................................................................................................................ 8 TEST EQUIPMENT LIST AND DETAILS ........................................................................................................................... 8 TEST RESULTS SUMMARY ............................................................................................................................................ 8 TEST DATA .................................................................................................................................................................. 8 FCC §15.109 - RADIATED EMISSIONS ................................................................................................................. 11 MEASUREMENT UNCERTAINTY .................................................................................................................................. 11 EUT SETUP ................................................................................................................................................................ 11 EMI TEST RECEIVER SETUP ....................................................................................................................................... 12 TEST PROCEDURE ...................................................................................................................................................... 12 CORRECTED AMPLITUDE & MARGIN CALCULATION ................................................................................................. 12 TEST EQUIPMENT LIST AND DETAILS ......................................................................................................................... 13 TEST RESULTS SUMMARY .......................................................................................................................................... 13 TEST DATA ................................................................................................................................................................ 13 Bay Area Compliance Laboratories Corp. (Dongguan) Report No.: R1XM120806050-00 FCC Part15B, Class B Page 3 of 17 GENERAL INFORMATION Product Description for Equipment under Test (EUT) The KAREL ELEKTRONIK SANAYI VE TICARET A.S.’s produc…

Text truncated - open the document above for the full version.

EXHIBIT D - TEST SETUP PHOTOGRAPHS Conduction Emissions - Front View Conduction Emissions - Side View Below 1GHz: Radiated Emissions - Front View Below 1GHz: Radiated Emissions - Rear View