P27970F208F4WLAN Printer Server

Wireless Print Server User Guide Copyright2001.ALL RIGHTS RESERVED Document Version: 1.0 (October, 2001) P/N: 9570F20001 All trademark and trade names are the properties of their respective owners. FEDERAL COMMUNICATIONS COMMISSION INTERFERENCE STATEMENT This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: -- Reorient or relocate the receiving antenna. -- Increase the separation between the equipment and receiver. -- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. -- Consult the dealer or an experienced radio/TV technician for help. CAUTION: Any changes or modifications not expressly approved by the grantee of this device could void the user's authority to operate the equipment. FCC RF Radiation Exposure Statement This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20cm between the radiator and your body. Page 1 Chapter 1 Introduction This chapter provides an overview of your Print Server's features. Features Congratulations on the purchase of your new Print Server. This device was designed to provide a simple and efficient network printing solution. It is packed with features, including: ¾ Versatility. The Print Server supports TCP/IP, SMB (Service Message Block), AppleTalk (EtherTalk), and NetBEUI. Operating system support includes Apple, Unix, and Microsoft Windows. The PS723H also provides full support for Novell NetWare. ¾ Easy Installation and Setup. Installation can be accomplished in minutes. For initial configuration, a number of utility programs are supplied to simplify setup. For Windows 95/98/NT/ME/2000/XP users, the supplied Wizard allows quick and easy setup. ¾ Web-based Interface. The Web-based interface provides an easy method of configuration in TCP/IP networks. ¾ Compact Size. This allows the Print Server to be used even where space is limited. ¾ Remote Management Tools. A variety of software tools are provided. In most environments, both the Print Server and attached bi-directional printers can be configure d remotely, from any station on your LAN. For Windows users, the supplied BiAdmin program makes it easy to configure the Print Server for a variety of network and server configurations ¾ SNMP Support. The Print Server can act as a SNMP agent, with it's own MIB. This allows TCP/IP users to monitor, configure and troubleshoot the Print Server using their existing SNMP management tools. ¾ JetAdmin Support.. If you are already using HP's JetAdmin, you can also use this program to manage your Print Server. ¾ Internet Printing Protocol (IPP) Support. All models can act as an IPP (Internet Printing Protocol) Server, allowing clients, suppliers, colleagues and others to print to your printer from anywhere on the Internet. Windows IPP Client software is also supplied. ¾ Wireless LAN Support. Wireless stations supporting the IEEE 802.11b standard can interoperate with the Wireless Print Server. Both LAN and WLAN users can print to the attached printer. ¾ Wireless Access Point (PS723H only). The PS723H can act as a Wireless Access Point, allowing Wireless Stations to access LAN resources. The IEEE 802.11b standard is fully supported, including WEP and access control. 1 Page 2 Safety Instructions For your own safety, and to protect your Print Server, please observe the following safety advice. 1.Unplug this device from its power source before cleaning. Use only a slightly dampened cloth for cleaning. Do not use liquid or aerosol cleaners. 2.Avoid using this product near water. Exposure to water poses an electric -shock hazard. 3.Do not place the Print Server on an unstable surface. The device may fall causing serious damage to the device. 4.This device should only be used with the power supply type specified on the marking label. If you are not sure of type of your local power supply, consult your dealer or the local power company. 5.Do not pinch, crimp or otherwise damage the power cord. If exposed to foot traffic, ensures that the cable is properly shielded and does not pose a tripping hazard. 6.If using an extension cord, makes sure the total ampere rating of the products using the cord does not exceed the extension cord's ampere rating. 7.Do not attempt to service this device, as opening or removing casing may expose you to dangerous voltage points or other risks. Refer all servicing to qualified service personnel. 8.The Print Server should be serviced by qualified service personnel under the following conditions: • The power cord is damaged or frayed. • Liquid has been spilled onto the product. • The product has been exposed to rain or water. • The product does not operate normally in accordance with the operating instructions. • The device has been dropped or the casing has been damaged. Page 3 Package Contents You should find the following items packaged with your Print Server. If any items are missing, contact your dealer immediately. • The Print Server • Power Adapter • One CD-ROM containing all support programs and this manual • Quick Install Guide • Wireless PCMCIA Card Models This manual covers the following Wireless Print Server models. Details of the LEDs is in…

Text truncated - open the document above for the full version.

Report No.: 01BH041FI Page : 1 of 5 Version : 1.0 Attachment 2 : EUT Detailed Photographs M/N: PD507B (1) EUT Photo (Connect to long antennas 5dBi) (2) EUT Photo (Connect to long antennas 5dBi) Report No.: 01BH041FI Page : 2 of 5 Version : 1.0 M/N: PD507B (3) EUT Photo (Connect to short antennas 2dBi) (4) EUT Photo (Connect to short antennas 2dBi) Report No.: 01BH041FI Page : 3 of 5 Version : 1.0 M/N: PS7100 (5) EUT Photo (Connect to long antennas 5dBi) (6) EUT Photo (Connect to long antennas 5dBi) Report No.: 01BH041FI Page : 4 of 5 Version : 1.0 M/N: PS7100 (7) EUT Photo (Connect to short antennas 2dBi) (8) EUT Photo (Connect to short antennas 2dBi) Report No.: 01BH041FI Page : 5 of 5 Version : 1.0 M/N: WPS11 (9) EUT Photo (Connect to long antennas 5dBi) (10) EUT Photo (Connect to long antennas 5dBi)

FCC ID.: P27970F208F4 The FCC ID and DoC Label will be placed on the equipment as shown in the photograph below. WLAN Printer Server Model No.: WPS11, PS7100, PD507B F F C C C C I I D D : : P P 2 2 7 7 9 9 7 7 0 0 F F 2 2 0 0 8 8 F F 4 4 This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference and (2) this device must accept any interference received, including interference that may cause undesired operation. S/N: Made in Taiwan

FCC ID.: P27970F208F4 LabelLoc

Report No.: 01BH041FI Page : 1 of 16 Version : 1.0 Attachment 2 : EUT Detailed Photographs M/N: PD507B (1) EUT Photo (2) EUT Photo Report No.: 01BH041FI Page : 2 of 16 Version : 1.0 M/N: PD507B (3) EUT Photo (4) EUT Photo Report No.: 01BH041FI Page : 3 of 16 Version : 1.0 M/N: PD507B (5) EUT Photo Report No.: 01BH041FI Page : 4 of 16 Version : 1.0 M/N: PD507B (6) EUT Photo Report No.: 01BH041FI Page : 5 of 16 Version : 1.0 M/N: PD507B (7) EUT Photo Report No.: 01BH041FI Page : 6 of 16 Version : 1.0 M/N: PD507B (8) EUT Photo (9) EUT Photo Report No.: 01BH041FI Page : 7 of 16 Version : 1.0 M/N: PD507B (10) EUT Photo (11) EUT Photo Report No.: 01BH041FI Page : 8 of 16 Version : 1.0 M/N: PD507B (12) EUT Photo Report No.: 01BH041FI Page : 9 of 16 Version : 1.0 M/N: PS7100 & WPS11 (13) EUT Photo (14) EUT Photo Report No.: 01BH041FI Page : 10 of 16 Version : 1.0 M/N: PS7100 & WPS11 (15) EUT Photo (16) EUT Photo Report No.: 01BH041FI Page : 11 of 16 Version : 1.0 M/N: PS7100 & WPS11 (17) EUT Photo Report No.: 01BH041FI Page : 12 of 16 Version : 1.0 M/N: PS7100 & WPS11 (18) EUT Photo Report No.: 01BH041FI Page : 13 of 16 Version : 1.0 M/N: PS7100 & WPS11 (19) EUT Photo Report No.: 01BH041FI Page : 14 of 16 Version : 1.0 M/N: PS7100 & WPS11 (20) EUT Photo (21) EUT Photo Report No.: 01BH041FI Page : 15 of 16 Version : 1.0 M/N: PS7100 & WPS11 (22) EUT Photo (23) EUT Photo Report No.: 01BH041FI Page : 16 of 16 Version : 1.0 M/N: PS7100 & WPS11 (24) EUT Photo

Report No. 01BH041FI Page : 1 of 66 Version:1.0 Test Report Product Name : WLAN Printer Server Model No. : WPS11, PS7100, PD507B FCC ID.: P27970F208F4 Applicant : SerComm Corp. Address : 10th F1., No.19-13, San Chung Road Nankang, Taipei City, Taiwan 115, R.O.C. Date of Receipt : Nov.23, 2001 Date of Test : Dec.05, 2001 Report No. : 01BH041FI The Test Results relate only to the samples tested. The test report shall not be reproduced except in full without the written approval of QuieTek Corporation. This report must not be used to claim product endorsement by NVLAP any agency of the U.S. Government Report No. 01BH041FI Page : 3 of 66 Version:1.0 TABLE OF CONTENTS Description Page 1. GENERAL INFORMATION .....................................................................................................5 1.1. EUT Description............................................................................................................................5 1.2. Operational Description ................................................................................................................6 1.3. Tested System Details....................................................................................................................7 1.4. Configuration of tested System .....................................................................................................8 1.5. EUT Exercise Software .................................................................................................................8 1.6. Test Facility ...................................................................................................................................9 2. Conducted Emission..................................................................................................................10 2.1. Test Equipment List.....................................................................................................................10 2.2. Test Setup ....................................................................................................................................10 2.3. Limits ..........................................................................................................................................10 2.4. Test Procedure .............................................................................................................................11 2.5. Test Result of Conducted Emission.............................................................................................12 3. Peak Power Output ...................................................................................................................13 3.1. Test Equipment............................................................................................................................14 3.2. Test Setup ....................................................................................................................................14 3.3. Test Condition .............................................................................................................................14 3.4. Minimum Standard......................................................................................................................14 3.5. Test Result of Peak Power Output...............................................................................................15 4. RF Exposure Evaluation ...........................................................................................................16 4.1. Friis Formula ...............................................................................................................................16 4.2. EUT Operation condition ............................................................................................................16 4.3. Test Result of RF Exposure Evaluation.......................................................................................17 5. Radiated Emission .....................................................................................................................18 5.1. Test Equipment............................................................................................................................18 5.2. Test Setup ....................................................................................................................................18 5.3. Test Condition .............................................................................................................................19 5.4. Limits ..........................................................................................................................................19 5.5. Test Procedure .............................................................................................................................20 5.6. Test Result of Radiated Emission................................................................................................21 6. Band Edge ..................................................................................................................................45 6.1. Test Equipment............................................................................................................................45 6.2. Test Setup ....................................................................................................................................45 6.3. Test Condition .............................................................................................................................46 6.4. Standard Reqirement ...................................................................................................................46 6.5. Test Result of Band Edge ............................................................................................................47 7. Occupied Bandwidth .................................................................................................................…

Text truncated - open the document above for the full version.

Report No.: 01BH041FI Page: 1 of 6 Version: 1.0 Attachment 1 : EUT Test Photographs Front View of Conducted Test (Mode 1) Back View of Conducted Test (Mode 1) Report No.: 01BH041FI Page: 2 of 6 Version: 1.0 Front View of Conducted Test (Mode 2) Back View of Conducted Test (Mode 2) Report No.: 01BH041FI Page: 3 of 6 Version: 1.0 Front View of Radiated Test (Mode 1) Back View of Radiated Test (Mode 1) Report No.: 01BH041FI Page: 4 of 6 Version: 1.0 Front View of Radiated Test (Mode 2) Back View of Radiated Test (Mode 2) Report No.: 01BH041FI Page: 5 of 6 Version: 1.0 Front View of Radiated Test (Mode 1-Horn) Report No.: 01BH041FI Page: 6 of 6 Version: 1.0 Front View of Radiated Test (Mode 2-Horn) -