P3IKIDGUARDWireless Kid Guard

Kid Guard USER'S MANUAL ’ ’ ’ ’ ’ ’’ FCC Compliance Statements NOTE : This equipment has been tested and found to comply with the limits for a FCC Subpart C device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates ,uses and can radiate radio frequency energy and ,if not installed and used in accordance with the instruction , may cause harmful interference to radio communication. However , there is no guarantee that interference will not occur in a particular installation. If this equipment dose harmful interference to radio or television reception ,which can be determined by turning the equipment off and on. The user is encouraged to try to correct the interference by one or more of the following measures : - Reorient or relocate the receiving antenna - Increase the separation between the equipment and receiver. - Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. - Consult the dealer or an experienced radio / TV technician for help. Warning : Your are cautioned that any change or modifications to the equipment not prissily approved by the party responsible for compliance could void your authority to operate such equipment. NOTE : This unit was tested with shielded cables on the peripheral device . Shield cables must be used with the unit to insure compliance.

Model : Kid Guard Test Report No. : 01JAC024.FCC APPENDIX 3 System Block Diagram 2001 JungAng EMC Co., Ltd. FCC ID : P3IKIDGUARD Page 1 of 2 Model : Kid Guard Test Report No. : 01JAC024.FCC 2001 JungAng EMC Co., Ltd. FCC ID : P3IKIDGUARD Page 2 of 2

Model : Kid Guard Test Report No. : 01JAC024.FCC A1-1 External Photo of EUT( ) A1-2 External Photo of EUT( )  JungAng EMC Co., Ltd. FCC ID : P3IKIDGUARD Page 2 of 4

Model : Kid Guard Test Report No. : 01JAC024.FCC APPENDIX 2 ID Label and Location  JungAng EMC Co., Ltd. FCC ID : P3IKIDGUARD Page 1 of 3 Model : Kid Guard Test Report No. : 01JAC024.FCC A2-1 Label Requirements A FCC subpart C equipment subject to certification by the FCC shall carry a warning label which includes the following statements: This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This statement should be stuck in a conspicuous location on the device. If impossible, this warning label should be placed in a prominent location in the user’s manual. A2-2 ID Label Drawing NAITS INC. Model No : Kid Guard Serial No : xxxxxxx FCC ID : P3IKIDGUARD NAITS INC. Made in Korea. A2-3 ID Label Location : Bottom & side of EUT  JungAng EMC Co., Ltd. FCC ID : P3IKIDGUARD Page 2 of 3 Model : Kid Guard Test Report No. : 01JAC024.FCC A2-4 Warning Labels Operation manuals for fcc subpart C devices shall contain the following statements or their equivalent : Note: This equipment has been tested and found to comply with the limits for a fcc subpart C device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: - Reorient or relocate the receiving antenna. - Increase the separation between the equipment and receiver. - Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. - Consult the dealer or an experienced radio/TV technician for help. y NOTE: You are cautioned that any change or modifications to the equipment not expressly approved by the party responsible for compliance could void your authority to operate such equipment. In case that shielded cables were used on the test, operation manuals shall contain the following statements or their equivalent : y NOTE: This unit was tested with shielded cables on the peripheral devices. Shielded cables must be used with the unit to insure compliance.  JungAng EMC Co., Ltd. FCC ID : P3IKIDGUARD Page 3 of 3

Model : Kid Guard Test Report No. : 01JAC024.FCC A1-3 Inside Photo of EUT A1-4 Top PCB Photo of EUT  JungAng EMC Co., Ltd. FCC ID : P3IKIDGUARD Page 3 of 4

Model : Kid Guard Test Report No. : 01JAC024.FCC APPENDIX 5 RF DESCRIPTION  JungAng EMC Co., Ltd. FCC ID : P3IKIDGUARD Page 1 of 2 Model : Kid Guard Test Report No. : 01JAC024.FCC 2 7 A 1 2 V U4 BAT:23A12V 1 2 + - C6 10pF SW1 POWER 3 2 1 C3 104 U1 PIC12C508A 1 2 3 45 6 7 8 VDD GP5/OSC1 GP4/OSC2 GP3/MCLRT0CKI/GP2 GP1 GP0 VSS U3 RO2149 1 2 3 T1 T2 GND R210 R4 5.1k D1 ZENER 5V Q1 2N2757[mark:H3O] C1 104 C4 100pF R1 20K C5 2pF Loop Ant C210pF_VAR 12 12 R3 470  JungAng EMC Co., Ltd. FCC ID : P3IKIDGUARD Page 2 of 2

Model : Kid Guard Test Report No. : 01JAC024.FCC APPENDIX 4 System Schematics  JungAng EMC Co., Ltd. FCC ID : P3IKIDGUARD Page 1 of 2 Model : Kid Guard Test Report No. : 01JAC024.FCC 2 7 A 1 2 V U4 BAT:23A12V 1 2 + - C6 10pF SW1 POWER 3 2 1 C3 104 U1 PIC12C508A 1 2 3 45 6 7 8 VDD GP5/OSC1 GP4/OSC2 GP3/MCLRT0CKI/GP2 GP1 GP0 VSS U3 RO2149 1 2 3 T1 T2 GND R210 R4 5.1k D1 ZENER 5V Q1 2N2757[mark:H3O] C1 104 C4 100pF R1 20K C5 2pF Loop Ant C210pF_VAR 12 12 R3 470  JungAng EMC Co., Ltd. FCC ID : P3IKIDGUARD Page 2 of 2

Model : Kid Guard Test Report No. : 01BWS003.FCC 
 BWS Tech, Inc. FCC ID : P3IKIDGUARD Page 1 of 11 BWS Tech, Inc. 294-9, Jungdae-Dong, Gwangju-City, Gyeoeonggi-do 464-809 Korea TEL: 82 31 764 0125 FAX: 82 31 764 0126
  
  
  
     Date of Test : December 26, 2001 Test Report No : 01BWS003.FCC Test Site : BWS Tech, Inc. (Registration No. : 553281) Trade Name : N/A Manufacturer : NAITS INC Address : SeoHwa B/D #839-8 YeokSam-Dong, KangNam-Gu, Seoul, Korea. Contact Person : Chang Il, Kim Tel No. : 82-2-569-5869 Fax No. : 82-2-569-5847 Product : Wireless Kid Guard Model : Kid Guard Fcc Rule Part(s) : FCC Part 15 Subpart C Classification : N/A The device bearing the trade name and model specified above has been shown to comply with the applicable technical standards as indicated in the measurement report and was tested in accordance with the measurement procedures specified in ANSI C.63.4-2000. I attest to the accuracy of data and all measurement reported herein were performed by me or were made under my supervision and are correct to the best of my knowledge and belief. I assume full responsibility for the completeness of these measurements and vouch for the qualification of all persons taking them. TaeHyun Nam President-BWS Tech, Inc. http://www.approvalspecialists.co.kr Model : Kid Guard Test Report No. : 01BWS003.FCC 
 BWS Tech, Inc. FCC ID : P3IKIDGUARD Page 2 of 11 TABLE OF CONTENTS PAGE 1. Description of device 3 1.1 General 3 1.2 EUT Description 3 2. Test facility 4 3. Summary of results 4 3.1 Electromagnetic Emission 4 3.2 Modifications to the EUT 4 4. Tested system details 5 4.1 Peripherals and Others 5 4.2 Type of Cables Used 5 4.3 System layout on EUT and peripherals 5 5. Test result 6 5.1 RFI Voltage Measurement 6 5.2 RFI Field Strength Measurement 6 5.3 Minimum Margin 10 5.4 Sample Calculations 10 6. Measurement Photos 11 6.1 Setup with RFI Field Strength Emission Level 11





Model : Kid Guard Test Report No. : 01BWS003.FCC 
 BWS Tech, Inc. FCC ID : P3IKIDGUARD Page 3 of 11 1. DESCRIPTION OF DEVICE 1.1 General Responsible Party NAITS INC Contact Person Chang Il, Kim Tel No. : 82-2-569-5869 Fax No. : 82-2-569-5847 Manufacturer NAITS INC SeoHwa B/D #839-8 YeokSam-Dong, KangNam-Gu, Seoul, Korea. • Trade name N/A • Model name Kid Guard • EUT Type Wireless Kid Guard • Classification N/A • Tx Frequency 311.06 MHz • Clock Speed Main Clock : 311.06 MHz • Rule Part(s) FCC Part 15 Subpart C § 15.231 • Test Procedure(s) ANSI C63.4(2000) • Date of Tests DECEMBER. 26, 2001 • Place of Tests BWS Tech, Inc. 1.2 EUT Description This product is radio system that is manufactured by missing child prevention.



Note. This report may be reproduced in full. Partial reproduction may only be made with the written permission of the laboratory. The results in this report is only applied to the sample(s) tested.



Note. Please refer to the duties and responsibilities of the Responsible Party attached. Model : Kid Guard Test Report No. : 01BWS003.FCC 
 BWS Tech, Inc. FCC ID : P3IKIDGUARD Page 4 of 11 2. TEST FACILITY The open field test site and conducted measurement facility used for this measurement, is located following address. This site was fully described in a report dated Dec. 26, 2001 that was submitted to the FCC. Our site and facility had been accepted in a letter dated Dec. 26, 2001(Registration No. : 553281) : BWS Tech, Inc. Address : 294-9, Jungdae-Dong, Gwangju-City, Gyeonggi-Do 464-809 Korea The detailed description of the measurement facility was found to be in compliance with the requirements of ­2.948 according to ANSI C63.4 on Dec. 08, 2000. 3. SUMMARY OF RESULTS 3.1 Electromagnetic Emission RFI Voltage Measurement N/A RFI Field Strength Measurement PASS Although the measured emissions indicate that the EUT complies with the required limits, some measurement are close to these limits. When the uncertainty of measurement is considered, there is some possibility that the EUT may not be compliant. 3.2 Modifications to the EUT : None Model : Kid Guard Test Report No. : 01BWS003.FCC 
 BWS Tech, Inc. FCC ID : P3IKIDGUARD Page 5 of 11 4. TESTED SYSTEM DETAILS 4.1 Peripherals and Others : Description Model Name Serial No. Manufacturer FCC ID EUT Kid Guard - NAITS INC - 4.2 Type of Cables Used: Device from Device to Type of Cable Length Type of shield - - - - - 4.3 System layout on EUT and peripherals Figure 4-1 System layout EUT Model : Kid Guard Test Report No. : 01BWS003.FCC 
 BWS Tech, Inc. FCC ID : P3IKIDGUARD Page 6 of 11 5. TEST RESULT 5.1 RFI Voltage Measurement N/A 5.2 RFI Field Strength Measurement 5.2.1 Measurement Instrumentation Used (30MHz ~ 1000MHz) Signal Analyzer (PMM9000/3100J70602/PMM/10 Oct. 2001/Oct. 2002) Spectrum Analyzer (R3261/61720002/Advantest/25 Aug. 2001/Aug. 2002) Biconical antenna (BC01/0020J70501/PMM/10 Oct. 2001/Oct. 2002) Log periodic antenna (LP01/0020J70501/PMM/10 Oct. 2001/Oct. 2002) Coaxial cable (RG213U/---/MARLOW/--/--) (Over 1000MHz) Pre-amplifier (8449B/3008A00682)HP/02 Jun. 2001/Jun. 2002) Spectrum Analyzer (8563E/3450A02895)HP/25 Jun. 2001/Jun. 2002) Horn Antenna (BBHA9120D/0501/SCHWARZBECK/23 Mar. 2001/Mar. 2002) Coaxial cable (Sucoflex 104/---/SUCOFLEX/--/--) 5.2.2 Measurement Procedure Final test was performed according to ANSI C63.4-2000 at the open field site . Deviations from the standard were none. The EUT was placed in a 0.8 m high table along with the peripherals. The turn table was separated from the antenna with the distance of 3 meter. Cables were placed in a position to produce maximum emissions as determined by experimentation, and operation mode was selected for maximum. The frequencies and amplitudes of maximum emission were measured at varying azimuths, antenna heights and antenna polarities. We measured device in normal operation mode. We reported at maximum emission levels. 5.2.3 Operation Modes EUT was tested according to the spe…

Text truncated - open the document above for the full version.

Model : Kid Guard Test Report No. : 01BWS003.FCC 
 BWS Tech, Inc. FCC ID : P3IKIDGUARD Page 11 of 11 6. MEASUREMENT PHOTOS 6.1 Setup with the Maximized RFI Field Strength Emission Level