P8BCA-2000RFWireless Video Sender

USB Remote Surveillance System 1 USB Remote Surveillance System Quick Reference Guide Receiver Transmitter USB Remote Surveillance System 2 Table Of Contents: Chapter 1: Introduction.......................................................4 Chapter 2: Minimum System Requirements...............................4 Chapter 3: Receiver Setup.....................................................5 Chapter 4: Wireless Camera Setup...........................................9 Chapter 5: Using Amcap5a .................................................10 Chapter 6: Customer/Technical Support...................................12 Chapter 7: Copyright.........................................................12 USB Remote Surveillance System 3 Federal Communications Commission (FCC) Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: -Reorient or relocate the receiving antenna. -Increase the separation between the equipment and receiver. -Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. -Consult the dealer or an experienced radio/TV technician for help. You are cautioned that changes or modifications not expressly approved by the party responsible for compliance could void your authority to operate the equipment. USB Remote Surveillance System 4 Chapter 1: Introduction Congratulations on your purchase of the USB Remote Surveillance System (Transmitter: CA-2000RF, Camlinc & Receiver: SG-W4A3, S-912RFB, Gateway, S-912RF). It allows you to connect up to 4 wireless cameras and 3 CCTV cameras to monitor your home, office, baby’s room, parking lot, or warehouse. Over the Internet, users can remotely view what has been captured by the cameras, or have a realtime view of the cameras over a standard web browser. The USB Remote Surveillance System is easy to use and able to do real-time video capture, motion detection and video recording. With the USB Remote Surveillance System, your life will be more convenient and secure. Please note that no antenna other than that supplied by the manufacturer shall be used with the device, and the use of a standard antenna jack or electrical connector is prohibited. If your device (SG-W4A3, S-912RFB, Gateway, or S-912RF) comes with a broken antenna, please do not attempt to fix it yourself, instead please contact the dealer you purchased this device from. Chapter 2: Minimum System Requirements • IBM ® or 100% compatible personal computer • Available USB port USB Remote Surveillance System 5 • Microsoft ® Windows ® 98/98SE/ME, or Windows 2000 • Pentium ® CPU 166 MHz or higher • 32 MB of RAM • 12 MB or more hard drive space Chapter 3: Receiver Setup Setting up your receiver (S-912RFB, SG-W4A3, S-912RF, or Gatway) is easy. Simply follow the steps below, and you will be ready to remotely monitor your home, warehouse, garage, and day-care center. Connect your receiver to an available USB port on your computer, and the Hardware Wizard of Windows 98/98SE/ME/2000 will automatically detect this device. ü Once you see a dialogue box with “This wizard searches for new drivers for USB Composite Device” during the hardware setup, please do the following: • Click “Next” to go to the next dialogue box • When you see a dialogue box with “What do you want Windows to do?”, select “Search for the best driver for your device. (Recommended).” and click “Next”. • When you are prompted by a dialogue box, “Windows will search for new drivers in its driver database...”, make sure there is a check mark beside “Floppy disk drives.” and click “Next”. USB Remote Surveillance System 6 • Windows has found an update driver..., choose “ The update driver USB S912RF Video Capture, AME Version 2.62”. • During the driver installation, Windows may prompt you to insert your Windows CD-ROM because it couldn’t find some specific data from the driver disk. When this happens, if you have your Windows CD-ROM, please insert it and direct Windows to copy the required files from your CD-ROM drive. (Click “Browse...” and select your CD-ROM drive) If you do not have your Windows CD-ROM available, you can still complete installation by the following steps: • When Windows cannot find the file, ‘ks.sys’, please go to “Browse...”, and direct the search to where you installed Windows. In our case is C: drive. • Then under C: drive, look for the “Windows” directory, and double click on it with your mouse. • When you are in the “Windows” directory, look for the “system32” directory, and double click on it. • Once you are in the “system32” directory, look for the “drivers” directory and double click on it, and there is your ‘ks.sys’ file. Click OK, then another OK to continue with the driver installation. • You may get a prompt by Windows saying that it could not find the file ‘ksclockf.ax’ and asks you to insert your Windows CD-ROM. If you already have your Windows CD-ROM inserted, you will not get this prompt. If you do not have the Windows CD-ROM, go to “Browse...” and follow the steps above, but make changes to the following: USB Remote Surveillance System 7 • When you are in the “Windows” directory, please replace the “system32” directory to the “system” directory. • Once you are in the “system” directory, you will be able to find the “ksclockf.a…

Text truncated - open the document above for the full version.

From: Nancy [[email protected]] Sent: Friday, March 22, 2002 7:35 PM To: Mike Kuo Subject: Re: AME OptimediaTechnology Co., Ltd., FCC ID:P8BCA-2000RF Importance: High Dear Mike, Thank you for your advice. Regarding your question for FCC ID: P8BCA-2000RF, the answers as below: Question #1: User manual does not contian information required under 15.21 of FCC rules. Please provide revised user manual to comply this requirements. Answer #1: Please see test report Appendix 2 of User manual Page 3. Question #2: Request for confidentiality box is checked on the TCB appliation form. Please provide a request for confidentiality letter to indicate which document should be withheld from public disclosure. Answer #2: Please see attachment: Confidentiality letter. Question #3: What is Page 15 of 53 test data for ? Frequency range investigated are under 30MHz but the test data is presented under Radaited emission tests. Answer #3: When I was transformed word.doc to PDF, the PC had some problem. So the page 15 is not the correct data. Now, please refer the page 15 of test report that had update. Best regards, Nancy ----- Original Message ----- From: "Mike Kuo" <[email protected]> To: <[email protected]> Cc: "Nancy (E-mail)" <[email protected]> Sent: Wednesday, March 20, 2002 4:07 AM Subject: FW: AME OptimediaTechnology Co., Ltd., FCC ID:P8BCA-2000RF > > > -----Original Message----- > From: CERTADM > Sent: Tuesday, March 19, 2002 12:06 PM > To: '[email protected]' > Subject: AME OptimediaTechnology Co., Ltd., FCC ID:P8BCA-2000RF > > > Notice_content > ------------- > Question #1: User manual does not contian information required under 15.21 > of FCC rules. Please provide revised user manual to comply this > requirements. > > Question #2: Request for confidentiality box is checked on the TCB > appliation form. Please provide a request for confidentiality letter to > indicate which document should be withheld from public disclosure. > > > Question #3: What is Page 15 of 53 test data for ? Frequency range > investigated are under 30MHz but the test data is presented under Radaited > emission tests. > > Best Regards > > Mike Kuo / TCB Certifier > The items indicated above must be submitted before processing can continue > on the above referenced application. Failure to provide the requested > information within 60 days of the original e-mail date may result in > application dismissal and forfeiture of the filing fee. Also, please note > that partial responses increase processing time and should not be submitted. > Any questions about the content of this correspondence should be directed to > the e-mail address listed below the name of the sender.

C&C Laboratory Co. Ltd. REPORT NO: 020010-R FCC ID: P8BCA-2000RF DATE: 03/13/2002 Accredited Lab. of NEMKO, A2LA, BSMI, CNLA NEMKO Authorization #: ELA 124 Page 48 of 53 Listed Lab. of FCC, VCCI, MOC A2LA Certificate #: 824.01 (for Emission) This report shall not be reproduced except in full, without the written approval of C&C Rev. 02 C&C Laboratory Co. Ltd. REPORT NO: 020010-R FCC ID: P8BCA-2000RF DATE: 03/13/2002 Accredited Lab. of NEMKO, A2LA, BSMI, CNLA NEMKO Authorization #: ELA 124 Page 52 of 53 Listed Lab. of FCC, VCCI, MOC A2LA Certificate #: 824.01 (for Emission) This report shall not be reproduced except in full, without the written approval of C&C Rev. 02

FCC ID LABEL FORMAT AND LOCATION Applicant: AME Optimedia Technology Co., Ltd.. FCC ID: P8BCA-2000RF FCC ID: P8BCA-2000RF This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. FCC ID LABEL AREA

C&C Laboratory Co. Ltd. REPORT NO: 020010-R FCC ID: P8BCA-2000RF DATE: 03/13/2002 Accredited Lab. of NEMKO, A2LA, BSMI, CNLA NEMKO Authorization #: ELA 124 Page 49 of 53 Listed Lab. of FCC, VCCI, MOC A2LA Certificate #: 824.01 (for Emission) This report shall not be reproduced except in full, without the written approval of C&C Rev. 02 C&C Laboratory Co. Ltd. REPORT NO: 020010-R FCC ID: P8BCA-2000RF DATE: 03/13/2002 Accredited Lab. of NEMKO, A2LA, BSMI, CNLA NEMKO Authorization #: ELA 124 Page 50 of 53 Listed Lab. of FCC, VCCI, MOC A2LA Certificate #: 824.01 (for Emission) This report shall not be reproduced except in full, without the written approval of C&C Rev. 02 C&C Laboratory Co. Ltd. REPORT NO: 020010-R FCC ID: P8BCA-2000RF DATE: 03/13/2002 Accredited Lab. of NEMKO, A2LA, BSMI, CNLA NEMKO Authorization #: ELA 124 Page 51 of 53 Listed Lab. of FCC, VCCI, MOC A2LA Certificate #: 824.01 (for Emission) This report shall not be reproduced except in full, without the written approval of C&C Rev. 02 C&C Laboratory Co. Ltd. REPORT NO: 020010-R FCC ID: P8BCA-2000RF DATE: 03/13/2002 Accredited Lab. of NEMKO, A2LA, BSMI, CNLA NEMKO Authorization #: ELA 124 Page 52 of 53 Listed Lab. of FCC, VCCI, MOC A2LA Certificate #: 824.01 (for Emission) This report shall not be reproduced except in full, without the written approval of C&C Rev. 02

C&C Laboratory Co. Ltd. REPORT NO: 020010-R FCC ID: P8BCA-2000RF DATE: 03/13/2002 Accredited Lab. of NEMKO, A2LA, BSMI, CNLA NEMKO Authorization #: ELA 124 Page 1 of 53 Listed Lab. of FCC, VCCI, MOC A2LA Certificate #: 824.01 (for Emission) This report shall not be reproduced except in full, without the written approval of C&C Rev. 02 ELECTROMAGNETIC EMISSIONS COMPLIANCE REPORT INTENTIONAL RADIATOR CERTIFICATION TO FCC PART 15 SUBPART C REQUIREMENT OF USB Remote Surveillance System Transmitter MODEL NO.: CA-2000RF PRODUCT FAMILY: Camlinc FCC ID: P8BCA-2000RF REPORT NO: 020010-R ISSUE DATE: March 13, 2002 Prepared for AME Optimedia Technology Co., Ltd. 17F-2, No. 79, Hsin Tai Wu Road, Sec. 1, His-Chih, Taipei Hsien, Taiwan, R. O. C. Prepared by C&C LABORATORY, CO., LTD. #B1, 1 st Fl., Universal Center, No. 183, Sec. 1, Tatung Rd., Hsi Chih, Taipei Hsien, Taiwan, R.O.C. TEL: (02)8642-2071~3 FAX: (02)8642-2256 C&C Laboratory Co. Ltd. REPORT NO: 020010-R FCC ID: P8BCA-2000RF DATE: 03/13/2002 Accredited Lab. of NEMKO, A2LA, BSMI, CNLA NEMKO Authorization #: ELA 124 Page 2 of 53 Listed Lab. of FCC, VCCI, MOC A2LA Certificate #: 824.01 (for Emission) This report shall not be reproduced except in full, without the written approval of C&C Rev. 02 TEST REPORT CERTIFICATION Applicant : AME Optimedia Technology Co., Ltd. Manufacturer : AME Optimedia Technology Co., Ltd. Description of EUT a) Product : USB Remote Surveillance System Transmitter b) Model No. : CA-2000RF c) Product Family : Camlinc e) AC Power Adaptor : Model Name: SCP41-750500 INPUT: 120VAC / 60Hz / 7W; OUTPUT:7.5VDC / 500mA Note: The difference between the two model numbers (listed on the report) is identical, just for marketing purpose only Regulation Applied : FCC Rules and Regulations Part 15 Subpart C (2000) I HEREBY CERTIFY THAT: The data shown in this report were made in accordance with the procedures given in ANSI C63.4, and the energy emitted by the device was founded to be within the limits applicable. I assume full responsibility for accuracy and completeness of these data. Note: 1. The result of the testing report relate only to the item tested. 2. The testing report shall not be reproduced expect in full, without the written approval of C&C Laboratory Co. Ltd. Issued Date : March 13, 2002 Approve & Authorized Signer : Steven Wang / RF Manager C&C Laboratory Co. Ltd. REPORT NO: 020010-R FCC ID: P8BCA-2000RF DATE: 03/13/2002 Accredited Lab. of NEMKO, A2LA, BSMI, CNLA NEMKO Authorization #: ELA 124 Page 3 of 53 Listed Lab. of FCC, VCCI, MOC A2LA Certificate #: 824.01 (for Emission) This report shall not be reproduced except in full, without the written approval of C&C Rev. 02 Table of Contents Page 1 GENERAL INFORMATION.............................................................................................................5 1.1 Product Description..............................................................................................................................5 1.2 Characteristics of Device......................................................................................................................5 1.3 Test Methodology................................................................................................................................5 1.4 Test Facility..........................................................................................................................................5 2 PROVISIONS APPLICABLE.............................................................................................................6 2.1 Definition..............................................................................................................................................6 2.2 Requirement for Compliance.................................................................................................................7 2.3 Restricted Bands of Operation..............................................................................................................9 2.4 Labeling Requirement...........................................................................................................................9 2.5 User Information................................................................................................................................10 3 SYSTEM TEST CONFIGURATION...............................................................................................11 3.1 Justification.........................................................................................................................................11 3.2 Devices for Tested System.................................................................................................................11 4 RADIATED EMISSION MEASUREMENT..................................................................................12 4.1 Applicable Standard...........................................................................................................................12 4.2 Measurement Procedure.....................................................................................................................12 4.3 Measuring Instrument.........................................................................................................................14 4.4 Radiated Emission Data......................................................................................................................15 4.4.1 Tx Portion.....................................................................................................................................15 4.4.2 Other Emissions.............................................................................................................................21 4.5 Field Strength Calculation...................................................................................................................28 4.6 Photos of Radiation Measuring Setup.................................................…

Text truncated - open the document above for the full version.

C&C Laboratory Co. Ltd. REPORT NO: 020010-R FCC ID: P8BCA-2000RF DATE: 03/13/2002 Accredited Lab. of NEMKO, A2LA, BSMI, CNLA NEMKO Authorization #: ELA 124 Page 29 of 53 Listed Lab. of FCC, VCCI, MOC A2LA Certificate #: 824.01 (for Emission) This report shall not be reproduced except in full, without the written approval of C&C Rev. 02 4.6 Photos of Radiation Measuring Setup C&C Laboratory Co. Ltd. REPORT NO: 020010-R FCC ID: P8BCA-2000RF DATE: 03/13/2002 Accredited Lab. of NEMKO, A2LA, BSMI, CNLA NEMKO Authorization #: ELA 124 Page 30 of 53 Listed Lab. of FCC, VCCI, MOC A2LA Certificate #: 824.01 (for Emission) This report shall not be reproduced except in full, without the written approval of C&C Rev. 02 C&C Laboratory Co. Ltd. REPORT NO: 020010-R FCC ID: P8BCA-2000RF DATE: 03/13/2002 Accredited Lab. of NEMKO, A2LA, BSMI, CNLA NEMKO Authorization #: ELA 124 Page 40 of 53 Listed Lab. of FCC, VCCI, MOC A2LA Certificate #: 824.01 (for Emission) This report shall not be reproduced except in full, without the written approval of C&C Rev. 02 5.6 Photos of Conduction Measuring Setup