P8JRPWLight Bulb

RPW-20E, PRW-26E Users Manual Instruction for Compact Fluorescent Lamp Major Features Brightness Brighter than an ordinary incandescent lamp. Energy Cost Savings Consumes 25% of electricity of an ordinary incandescent lamp. Longer Life Six times longer than an ordinary incandescent lamp. Other features Light weight and compact design. Instant (Flicker-free) start. Less Heat radiation thus reduce the load on air-conditioning systems. Insignificant electro-magnetic which affecting nearby TV and VCR. Applications STARWISE Energy Saving Lamps are suitable for installation in most indoor and outdoor lighting sockets. They are especially best for Lighting in long period of time. Such as: Hotels/Motels, Supermarkets, Department Stores, Gardens, Homes, Stores, Offices, Parks, etc... Precautions Never drop or strike the lamp. Never attempt to disassemble or modify the lamp. Never use with dimming circuit fixtures, emergency light fixtures, direct current fixtures and totally enclosed recessed fixtures. Never install where water may drop on the lamp and use in the dry locations. Never install where the temperature may rise above 40 ̊C. Never use on a source voltage that fluctuates 6% or above. Unsuitable for applications where the lamp may be turned on and off frequently. Note: This light device has been tested and found to comply with the limits for Consumer RF lighting Device, pursuant to Part 18 of the FCC rules. Any changes or modification to this unit not expressly approved by the party not responsible for compliance will void the user’s authority to operate the equipment. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. This product may cause interference to radio equipment and should not be installed near maritime safety communications equipment or other critical navigation or communication equipment operating between 0.45-30MHz.

EXTERNAL PHOTOGRAPHS EUT - Top View (RPW-20E) EUT - Rear View (RPW-20E) EUT - Top View (RPW-26E) EUT - Rear View (RPW-26E)

Proposed FCC Label Format Specifications: Text is black or white in color and is left justified. Labels are silk-screened and shall be “permanently affixed” at a conspicuous location on the EUT. Proposed Label Location on EUT Front View of EUT Proposed FCC Label Location

FCC ID Label 1. RPW-20E 2. SPW-26E

FCC ID Label 1. RPW-20E 2. SPW-26E

STARWISE INDUSTRIAL (HONG KONG) LTD.FCC ID: P8JRPW 5 – FCC PRODUCT LABELING AND WARNING STATEMENT 5.1 Proposed FCC Label Format Specifications: Text is black or white in color and is left justified. Labels are silk-screened and shall be “permanently affixed” at a conspicuous location on the EUT. 5.2 Proposed Label Location on EUT Front View of EUT Proposed FCC Label Location 5.3 FCC Warning Statement This device complies with Part 18 of FCC rules. Information on the following matters shall be provided to the user in the instruction manual or on the packaging if an instruction manual is not provided for any type of any ISM equipment: a. The interference potential of the device or system b. Maintenance of the system c. Simple measures that can be taken by the user to correct interference. FCC ID: P8JRPW

EXTERNAL PHOTOGRAPHS EUT - Component View (RPW-20E) EUT – Solder View (RPW-20E) EUT - Component View (RPW-26E) EUT - Solder View (RPW-26E)

Note: The test report is specially limited to the use of the above client company and the product model. It may not be duplicated without prior written consent of Bay Area Compliance Laboratory Corporation. This report must not be used by the client to claim product endorsement by NVLAP or any agency of the U.S. Government. FCC PART 18 MEASUREMENT AND TEST REPORT For STARWISE INDUSTRIAL (HONG KONG) LTD. RM. A, 17/F. CHEUNG HING SHING CENTRE, 23 SHA TSUI RD., TSUEN WAN, N.T., HONG KONG FCC ID: P8JRPW March 4, 2002 This Report Concerns: Original Report Equipment Type: Light Bulb Test Engineer:Wayne Chia Test Date:February 15, 2002 Reviewed By: John Y. Chan – Engineering Manager Prepared By:Bay Area Compliance Laboratory Corporation 230 Commercial Street Sunnyvale, CA 94085 Tel: (408) 732-9162 Fax: (408) 732-9164 STARWISE INDUSTRIAL (HONG KONG) LTD.FCC ID: P8JRPW Report # R02021313.DOCPage 2 of 22FCC Part 18 Report TABLE OF CONTENTS 1 - GENERAL INFORMATION.................................................................................................................................................3 1.1 PRODUCT DESCRIPTION FOR EQUIPMENT UNDER TEST (EUT).........................................................................................3 1.2 OBJECTIVE................................................................................................................................................................................3 1.3 RELATED SUBMITTAL(S)/GRANT(S)......................................................................................................................................3 1.4 TEST METHODOLOGY.............................................................................................................................................................3 1.5 TEST FACILITY.........................................................................................................................................................................3 1.6 TEST EQUIPMENT LIST AND DETAILS...................................................................................................................................4 1.7 EQUIPMENT UNDER TEST (EUT)...........................................................................................................................................4 2 - SYSTEM TEST CONFIGURATION..................................................................................................................................5 2.1 JUSTIFICATION.........................................................................................................................................................................5 2.2 SCHEMATICS / BLOCK DIAGRAM..........................................................................................................................................5 2.3 EQUIPMENT MODIFICATIONS.................................................................................................................................................5 2.4 CONFIGURATION OF TEST SYSTEM.......................................................................................................................................6 2.5 TEST SETUP BLOCK DIAGRAM..............................................................................................................................................6 3 - CONDUCTED EMISSIONS TEST DATA........................................................................................................................7 3.1 MEASUREMENT UNCERTAINTY.............................................................................................................................................7 3.2 EUT SETUP...............................................................................................................................................................................7 3.3 SPECTRUM ANALYZER SETUP...............................................................................................................................................7 3.4 TEST PROCEDURE....................................................................................................................................................................7 3.5 SUMMARY OF TEST RESULTS.................................................................................................................................................8 3.6 CONDUCTED EMISSIONS TEST DATA....................................................................................................................................8 3.7 PLOT(S) OF CONDUCTED EMISSIONS TEST DATA...............................................................................................................8 4 - RADIATED EMISSION DATA..........................................................................................................................................11 4.1 MEASUREMENT UNCERTAINTY...........................................................................................................................................11 4.2 EUT SETUP.............................................................................................................................................................................11 4.3 SPECTRUM ANALYZER SETUP.............................................................................................................................................11 4.4 TEST PROCEDURE..................................................................................................................................................................11 4.5 CORRECTED AMPLITUDE & MARGIN CALCULATION......................................................................................................12 4.6 SUMMARY OF TEST RESULTS...............................................................................................................................................12 4.7 RADIATED EMISSIONS TEST DATA.......................................…

Text truncated - open the document above for the full version.

Conducted Emission Photograph – Front View (RPW-20E) Conducted Emission Photograph – Rear View (RPW-20E) Radiated Emission Photograph – Front View (RPW-20E) Radiated Emission Photograph – Rear View (RPW-20E) Radiated Emission Photograph – Rear View (RPW-20E)