PJMCPR44RF Reader Module

INSTALLATION final - public (B) ID CPR44 User Manual.doc ID CPR44 ISO14443-A and -B RFID Reader OBID ® classic-pro Installation ID CPR44 FEIG ELECTRONIC GmbH Page 2 of 16 ID CPR44 User Manual.doc Note  Copyright 2010 - 2012 by FEIG ELECTRONIC GmbH Lange Strasse 4 D-35781 Weilburg Tel.: +49 6471 3109-0 http://www.feig.de With the edition of this document, all previous editions become void. Indications made in this manual may be changed without previous notice. The reproduction, distribution and utilization of this document as well as the communication of its contents to others without express authorization is prohibited. Offenders will be held liable for the payment of damages. All rights reserved in the event of the grant of a patent, utility model or design. Composition of the information in this document has been done to the best of our knowledge. FEIG ELECTRONIC GmbH does not guarantee the correctness and completeness of the details given in this manual and may not be held liable for damages ensuing from incorrect or incomplete information. Since, despite all our efforts, errors may not be completely avoided, we are always grateful for your useful tips. The instructions given in this manual are based on advantageous boundary conditions. FEIG ELECTRONIC GmbH does not give any guarantee promise for perfect function in cross environments and does not give any guaranty for the functionality of the complete system which incorporates the subject of this document. FEIG ELECTRONIC call explicit attention that devices which are subject of this document are not designed with components and testing methods for a level of reliability suitable for use in or in connection with surgical implants or as critical components in any life support systems whose failure to perform can reasonably be expected to cause significant injury to a human. To avoid damage, injury, or death, the user or application designer must take reasonably prudent steps to protect against system failures. FEIG ELECTRONIC GmbH assumes no responsibility for the use of any information contained in this document and makes no representation that they free of patent infringement. FEIG ELECTRONIC GmbH does not convey any license under its patent rights nor the rights of others. OBID ® and OBID i-scan ® is a registered trademark of FEIG ELECTRONIC GmbH. All brand names, trademarks or logos are property of their respective owners. OBID ® classic-pro Installation ID CPR44 FEIG ELECTRONIC GmbH Page 3 of 16 ID CPR44 User Manual.doc Contents 1. Safety Instructions / Warning - Read before start-up ! 4 2. Characterization ID CPR44.0x-xx 5 3. Installation and wiring 6 3.1. Dimensions ........................................................................................................................ 6 3.2. Connection X1, X2 - Vcc and Interface ............................................................................. 7 3.3. Digital Outputs ................................................................................................................... 8 3.4. SAM Module ....................................................................................................................... 9 3.4.1. Installation of a SAM Card.......................................................................................... 10 3.5. Installation notes ............................................................................................................. 11 3.5.1. Metallic surroundings ................................................................................................. 11 3.5.2. EMC effects on cables ............................................................................................... 11 3.5.3. EMC effects from magnetic fields ............................................................................... 12 4. Radio Approvals 13 4.1. Europe (CE) ...................................................................................................................... 13 4.2. USA (FCC) and Canada (IC) ............................................................................................ 14 5. Technical Data 15 OBID ® classic-pro Installation ID CPR44 FEIG ELECTRONIC GmbH Page 4 of 16 ID CPR44 User Manual.doc 1. Safety Instructions / Warning - Read before start-up ! • The device may only be used for the intended purpose designed by for the manufacturer. • The operation manual should be conveniently kept available at all times for each user. • Unauthorised changes and the use of spare parts and additional devices which have not been sold or recommended by the manufacturer may cause fire, electric shocks or injuries. Such unauthorised measures shall exclude any liability by the manufacturer. • The liability-prescriptions of the manufacturer in the issue valid at the time of purchase are valid for the device. The manufacturer shall not be held legally responsible for inaccuracies, errors, or omissions in the manual or automatically set parameters for a device or for an incorrect application of a device. • Repairs may only be executed by the manufacturer. • Installation, operation, and maintenance procedures should only be carried out by qualified personnel. • Use of the device and its installation must be in accordance with national legal requirements and local electrical codes . • When working on devices the valid safety regulations must be observed. • Special advice for carriers of cardiac pacemakers: Although this device doesn't exceed the valid limits for electromagnetic fields you should keep a minimum distance of 25 cm between the device and your cardiac pace- maker and not stay in an immediate proximity of the device respective the antenna for some time. OBID ® classic-pro Installation ID CPR44 FEIG ELECTRONIC GmbH Page 5 of 16 ID CPR44 User Manual.doc 2. Characterization ID CPR44 The reader modules ID CPR44 are designed for data exchange (read and write) with passive tran- sponder according ISO14443 type A and type B a…

Text truncated - open the document above for the full version.

Precautions User Manual ID CPR44 1 / 1 FCC ID No: FCC ID: PJMCPR44 File : CPR44 - PRECAUTIONS USER MANUAL.DOC Date : 2015-06-18 Installation instructions to the host manufacturer Changes or modifications made to the equipment not expressly approved by FEIG ELECTRONIC GmbH may void the FCC / IC authorization to operate this equipment. The use of the transceiver module is authorized in mobile or fixed host devices taking into account the conditions listed below:  OEM Integrator must ensure that the end user manual may not contain any information about the way to install or remove the module from the final product.  Depending on the final host device additional authorization requirements for the non- transmitter functions of the transmitter module may be required (i.e., Verification, or Declaration of Conformity) The OEM integrator is responsible for ensuring that after the module is installed and operational the host continues to be compliant with the Part 15B unintentional radiator requirements.  The information on the label and in the user manual is required to be incorporated in the user manual of the final host. See 47 CFR15 requirements for more details (e.g. 15.19 / 15.21 / 15.101 / 15.105 / RSS-GEN).  Additional label with the words ‘Contains FCC ID: PJMCPR44’ and ‘Contains IC: 6633A- CPR44’ shall be applied and visible from the outside of the host product.  The module must be installed and used in strict accordance with the manufacturer’s instructions as described in the user documentation that comes with the module.  The power supply for the module must be 5,0 to 5,25 V DC (Ripple 0...250 kHz < 10 mVpp).  It is not necessary to shield the module to comply with the FCC / IC requirements. The antenna must not be shielded.  The internal antenna of the module may not be removed, replaced nor modified. The antenna must not be co-located or operating in conjunction with any other antenna or transmitter. No additional antenna must be used. Mode d’emploi et précautions d’usage ID CPR44 1 / 1 FCC ID No: FCC ID: PJMCPR44 File : CPR44 - PRECAUTIONS USER MANUAL - FR.DOC Date : 2015-06-18 Instructions d’installation pour le fabricant principal Les changements ou modifications effectués par l’équipement ne sont pas approuvés par FEIG ELECTRONIC, il est possible que GmbH annule l’autorisation du FCC/ IC pour utiliser cet équipement. L’utilisation de cet émetteur récepteur est autorisée dans les dispositifs fixes ou mobiles en prenant en considération les conditions informées ci-dessous : • L’intégrateur OEM doit s’assurer que le manuel d’utilisateur ne contient aucune information sur l’installation ou le retrait du module du produit ultime. • Pour l’ultime dispositif principal, une autre autorisation est requise pour les fonctions de la non-transmission du module émetteur. (ex. Vérification, déclaration ou conformité) Après que le module soit installé et opérationnel, l’intégrateur OEM doit s’assurer que l’hôte continue de se conformer aux exigences du radiateur 15B. • Les informations sur le label et dans le manuel d’utilisateur doivent être introduites dans le manuel d’utilisateur pour l’ultime hôte. Se référer aux exigences 47 CFR15 pour plus de détails. (ex. 15.19 / 15.21 / 15.101 / 15.105 / RSS-GEN). • Le label additionnel aux ‘Contains FCC ID : PJMCPR44’ et ‘Contains IC : 6633A-CPR44’ doit être appliqué et visible sur le produit hôte. • Le module doit être installé et utilisé selon les instructions du fabricant dans la documentation d’utilisateur qui est communiquée avec le module. • L’alimentation du module doit être de 5,0 à 5,25 V DC (tension 0....250kHz < 10 mVpp). • S’il est nécessaire de protéger le module pour se conformer aux exigences du FCC/IC. L’antenne doit être protégée. • L’antenne interne du module ne doit pas être retirée, remplacée ni modifiée. Elle ne doit pas être co-implantée ni utilisée conjointement avec d’autres antennes ou émetteurs. Aucune autre antenne ne doit être utilisée.

CONFIDENTIALITY REQUEST for Certification Service in USA Federal Communication Commission Equipment Authorization Division, Application Processing Branch 7435 Oakland Mills Road Columbia, MD 21048 07.04.2015 TO WHOM IT MAY CONCERN Pursuant to Paragraphs §0.457 and 0.459 of the Commission’s Rules (47 C.F.R.) and Section §552(b)(4) of the Freedom of Information Act, we requests confidentiality for the following products: FCC ID Model name FCC ID: PJMCPR44 ID CPR44 1. Electrical Schematic ID CPR44 – Schematic.pdf (4 pages) 2. PCB Layout ID CPR44 – PCB-01.pdf (1 pages) 3. Block Diagram ID CPR44 – Blockdiagram-01.pdf (1 pages) 4. Bill of Material ID CPR44 – BOM-01.pdf (2 pages) 5. Description ID CPR44-Operational Discription-01.pdf (1 pages) For the product stated above, we request permanent confidentiality for exhibits which contain Operational Description, Block Diagram, Schematics, Parts Lists or Tune Up Information. The above exhibits contain our trade secrets and proprietary information that could be of benefit to our competitors. If you have any questions, please feel free to contact me at the address shown below. Sincerely, Date: 07.04.2015 City: Weilburg Name of applicant: Dipl.-Ing. Bernhard Schüßler, Signature: Contact name: Bernhard Schüßler Company: FEIG ELECTRONIC GmbH Address: Lange Straße 4 / 35781 Weilburg, Germany Phone: 00 49 645 ́71/3109 0 Fax: 00 49 645 ́71/3109 99 Email: [email protected]

IC/FCC Modular Approval Statement Receiver Federal Communication Commission Equipment Authorization Devision, Application Processing Branch 7435 Oakland Mills Road Columbia, MD 21048 Certification and Engineering Bureau Industry Canada Spectrum Engineering Branch 3701 Carling Avenue, Building 94 Ottawa, Ontario K2H 8S2 Subject: Modular Approval Statement Date: 17.06.2015 FCC Certification Number: PJMCPR44 Only applicable for IC certification: IC Company Number: 6633A-CPR44 UPN: ID CPR44 HVIN (Hardware Version Identification Number): ID CPR44 PMN: (Product Marketing Name) ID CPR44 HMN: (Host Marketing Name) FVIN: (Firmware Version Identification Number) TO WHOM IT MAY CONCERN Pursuant to Paragraphs RSP-100 Issue 10 November 2014 Item 7.3 and CFR § 15.212, we herewith declare for our module. Modular approval requirement Yes No * (a) The radio elements must have the radio frequency circuitry be shielded. Physical/discrete and tuning capacitors may be located external to the shield, but must be on the module assembly. No *Please provide a detailed explanation if the answer is “No.”: No critical radiated spurious emissions were measured. (b) The module shall have buffered modulation/data input(s) (if such inputs are provided) to ensure that the module will comply with the requirements set out in the applicable RSS standard under conditions of excessive data rates or over-modulation. Yes *Please provide a detailed explanation if the answer is “No.”: (c) The module shall have its own power supply regulation on the module. This is to ensure that the module will comply with the requirements set out in the applicable standard regardless of the design of the power supplying circuitry in the host device which houses the module. No *Please provide a detailed explanation if the answer is “No.”: The module has no own power supply regulation but a filter for external power supply. IC/FCC Modular Approval Statement (d) The module shall comply with the provisions for external power amplifiers and antennas detailed in this standard. The equipment certification submission shall contain a detailed description of the configuration of all antennas that will be used with the module. No *Please provide a detailed explanation if the answer is “No.”: No external power amplifiers and antennas. (e) The module shall be tested for compliance with the applicable standard in a stand-alone configuration, i.e. the module must not be inside another device during testing. Yes *Please provide a detailed explanation if the answer is “No.”: (f) The module shall comply with the Category I equipment labeling requirements and CFR § 15.212(a)(1)(vi). Yes *Please provide a detailed explanation if the answer is “No.”: (g) The module shall comply with applicable RSS-102 exposure requirements and any applicable FCC RF exposure requirement which are based on the intended use/configurations. Yes *Please provide a detailed explanation if the answer is “No.”: Only applicable for IC certification: (h) Is the modular device for an Industry Canada licence-exempt service? Yes Only applicable for FCC certification: (i) The modular transmitter complies with all applicable FCC rules. Instructions for maintaining compliance are given in the user instructions. Yes If you have any questions, please feel free to contact us at the address shown below Best Regards, Name: Bernhard Schüßler Company: FEIG ELECTRONIC GmbH Address: Lange Strasse 4, 35781 Weilburg, Germany Telephone No: +49 6471 3109 0 Fax No: +49 6471 3109 99 Email: [email protected] INFO for applicant: LMA may be granted when one or more of the requirements in the table above cannot be demonstrated. LMA will also be issued in those instances where applicants can demonstrate that they will retain control over the final installation of the device, such that compliance of the end product is assured. In such cases, an operating condition on the LMA for the module must state that the module is only approved for use when installed in devices produced by a specific manufacturer. When LMA is sought, the application for equipment certification must specifically state how control of the end product, into which the module will be installed, will be maintained, such that full compliance of the end product is always ensured.

Test report no.: 1-9651/15-01-01_AnnexB Page 1 of 4 Annex B This test report annex is electronically signed and valid without handwriting signature. For verification of the electronic signatures, the public keys can be requested at the testing laboratory. Test report annex authorised: Christoph Schneider Testing Manager Radio Communications & EMC Test report no.: 1-9651/15-01-01_AnnexB Page 2 of 4 Inter nal p ho tos of the E UT Photo 1, whole test assembly: Photo 2, EUT top view: Test report no.: 1-9651/15-01-01_AnnexB Page 3 of 4 Photo 3, EUT bottom view: Test report no.: 1-9651/15-01-01_AnnexB Page 4 of 4 Docu men t his to r y Version Applied changes Date of release Initial release 2015-05-18

Label ID CPR44 1 / 1 FCC ID No: FCC ID PJMCPR44 File : ID CPR44-LABLEL-01.DOC Date : 2015-06-17 Dimensions (W x H): ~ 28 x 9 mm²

Test report no.: 1-9651/15-01-01_AnnexB Page 1 of 4 Annex B This test report annex is electronically signed and valid without handwriting signature. For verification of the electronic signatures, the public keys can be requested at the testing laboratory. Test report annex authorised: Christoph Schneider Testing Manager Radio Communications & EMC Test report no.: 1-9651/15-01-01_AnnexB Page 2 of 4 Inter nal p ho tos of the E UT Photo 1, whole test assembly: Photo 2, EUT top view: Test report no.: 1-9651/15-01-01_AnnexB Page 3 of 4 Photo 3, EUT bottom view: Test report no.: 1-9651/15-01-01_AnnexB Page 4 of 4 Docu men t his to r y Version Applied changes Date of release Initial release 2015-05-18

TEST REPORT Test report no.: 1-9651/15-01-02 Testing laboratory Applicant CETECOM ICT Services GmbH Untertuerkheimer Strasse 6 – 10 66117 Saarbruecken / Germany Phone: + 49 681 5 98 - 0 Fax: + 49 681 5 98 - 9075 Internet: http://www.cetecom.com e-mail: [email protected] Accredited Testing Laboratory: The testing laboratory (area of testing) is accredited according to DIN EN ISO/IEC 17025 (2005) by the Deutsche Akkreditierungsstelle GmbH (DAkkS) The accreditation is valid for the scope of testing procedures as stated in the accreditation certificate with the registration number: D-PL-12076-01-00 FEIG ELECTRONIC GmbH Lange Str. 4 35781 Weilburg-Waldhausen / GERMANY Phone: +49 6471 31 09-0 Fax: +49 6471 310-999 Contact: Bernhard Schüßler e-mail: [email protected] Phone: +49 6471 310-9435 Manufacturer FEIG ELECTRONIC GmbH Lange Str. 4 35781 Weilburg-Waldhausen / GERMANY Test standard/s 47 CFR Part 15 Title 47 of the Code of Federal Regulations; Chapter I; Part 15 - Radio frequency devices RSS - 210 Issue 8 Spectrum Management and Telecommunications Radio Standards Specification - Licence-exempt Radio Apparatus (All Frequency Bands): Category I Equipment For further applied test standards please refer to section 3 of this test report. Test Item Kind of test item: RF Reader Module Model name: ID CPR44 FCC ID: PJMCPR44 IC: 6633A-CPR44 Frequency: 13.56 MHz Technology tested: RFID Antenna: Integrated antenna Power supply: 5 V DC by power supply Temperature range: -25°C to +70°C This test report is electronically signed and valid without handwriting signature. For verification of the electronic signatures, the public keys can be requested at the testing laboratory. Test report authorised: Test performed: Marco Bertolino Christoph Schneider Lab Manager Testing Manager Radio Communications & EMC Radio Communications & EMC Test report no.: 1-9651/15-01-02 Page 2 of 21 1 Table of contents 1 Table of contents ............................................................................................................................................ 2 2 General information ....................................................................................................................................... 3 2.1 Notes and disclaimer .......................................................................................................................... 3 2.2 Application details ............................................................................................................................... 3 3 Test standard/s ............................................................................................................................................... 3 4 Test environment ............................................................................................................................................ 4 5 Test item .......................................................................................................................................................... 4 5.1 Additional information ........................................................................................................................ 4 6 Test laboratories sub-contracted ................................................................................................................. 4 7 Description of the test setup ......................................................................................................................... 5 7.1 Shielded semi anechoic chamber ...................................................................................................... 6 7.2 Shielded full anechoic chamber......................................................................................................... 7 7.3 Conducted measurements normal and extreme conditions ........................................................... 8 8 Summary of measurement results ............................................................................................................... 9 9 Additional comments ..................................................................................................................................... 9 10 Measurement results ................................................................................................................................ 10 10.1 Occupied bandwidth ...................................................................................................................... 10 10.2 Field strength of the fundamental ................................................................................................ 12 10.3 Field strength of the harmonics and spurious ........................................................................... 13 10.4 Frequency error ............................................................................................................................. 16 10.5 Conducted limits ............................................................................................................................ 17 11 Observations ............................................................................................................................................. 19 Annex A Document history .......................................................................................................................... 20 Annex B Further information ........................................................................................................................ 20 Annex C Accreditation Certificate ............................................................................................................... 21 Test report no.: 1-9651/15-01-02 Page 3 of 21 2 General information 2.1 Notes and disclaimer The test results of this test report relate exclusively to the test item specified in this test report. CETECOM ICT Services GmbH does not assume responsibility for any conclusions and generalizations drawn from the test res…

Text truncated - open the document above for the full version.

Test report no.: 1-9651/15-01-01_AnnexD Page 1 of 5 Annex D This test report annex is electronically signed and valid without handwriting signature. For verification of the electronic signatures, the public keys can be requested at the testing laboratory. Test report annex authorised: Christoph Schneider Testing Manager Radio Communications & EMC Test report no.: 1-9651/15-01-01_AnnexD Page 2 of 5 EUT Test se tu p p h otos Photo 1: Photo 2: Test report no.: 1-9651/15-01-01_AnnexD Page 3 of 5 Photo 3: Photo 4: Test report no.: 1-9651/15-01-01_AnnexD Page 4 of 5 Photo 5: Photo 6: Test report no.: 1-9651/15-01-01_AnnexD Page 5 of 5 Docu men t his to r y Version Applied changes Date of release Initial release 2015-05-18