PJMCPR60RFID Reader

INSTALLATION draft – public (B) 2020-04-27 – CPR60_Installation M91210-0e_03.doc ID CPR60 RFID Reader Module Modell Artikel Nr. ID CPR60-A 5491.000.00 IDENTIFICATION Installation ID CPR60 FEIG ELECTRONIC GmbH Page 2 of 16 CPR60_Installation M91210-0e_03.doc Note  Copyright by FEIG ELECTRONIC GmbH Lange Strasse 4 D-35781 Weilburg Tel.: +49 6471 3109-0 http://www.feig.de With the edition of this document, all previous editions become void. Indications made in this manual may be changed without previous notice. The reproduction, distribution and utilization of this document as well as the communication of its contents to others without express authorization is prohibited. Offenders will be held liable for the payment of damages. All rights reserved in the event of the grant of a patent, utility model or design. Composition of the information in this document has been done to the best of our knowledge. FEIG ELECTRONIC GmbH does not guarantee the correctness and completeness of the details given in this manual and may not be held liable for damages ensuing from incorrect or incomplete information. Since, despite all our efforts, errors may not be completely avoided, we are always grateful for your useful tips. The instructions given in this manual are based on advantageous boundary conditions. FEIG ELECTRONIC GmbH does not give any guarantee promise for perfect function in cross environments and does not give any guaranty for the functionality of the complete system which incorporates the subject of this document. FEIG ELECTRONIC call explicit attention that devices which are subject of this document are not designed with components and testing methods for a level of reliability suitable for use in or in connection with surgical implants or as critical components in any life support systems whose failure to perform can reasonably be expected to cause significant injury to a human. To avoid damage, injury, or death, the user or application designer must take reasonably prudent steps to protect against system failures. FEIG ELECTRONIC GmbH assumes no responsibility for the use of any information contained in this document and makes no representation that they free of patent infringement. FEIG ELECTRONIC GmbH does not convey any license under its patent rights nor the rights of others. All brand names, trademarks or logos are property of their respective owners. IDENTIFICATION Installation ID CPR60 FEIG ELECTRONIC GmbH Page 3 of 16 CPR60_Installation M91210-0e_03.doc Content 1. Safety Instructions / Warning - Read before start-up ! 4 2. Characterization ID CPR60 5 2.1. Available Accessories ....................................................................................................... 5 2.2. Available Software Tools, USB Driver and Firmware ...................................................... 6 3. Dimensions 7 4. Installation and wiring 8 4.1. Connector X1 ..................................................................................................................... 8 4.2. Connector ANT ................................................................................................................ 10 5. Standby / Low Power Card Detection 11 6. Technical Data 12 7. Approvals 14 7.1. Europa (CE) ...................................................................................................................... 14 7.2. USA (FCC) and Canada (IC) ............................................................................................ 15 IDENTIFICATION Installation ID CPR60 FEIG ELECTRONIC GmbH Page 4 of 16 CPR60_Installation M91210-0e_03.doc 1. Safety Instructions / Warning - Read before start-up ! • The device may only be used for the intended purpose designed by for the manufacturer. • The operation manual should be conveniently kept available at all times for each user. • Unauthorised changes and the use of spare parts and additional devices which have not been sold or recommended by the manufacturer may cause fire, electric shocks or injuries. Such unauthorised measures shall exclude any liability by the manufacturer. • The liability-prescriptions of the manufacturer in the issue valid at the time of purchase are valid for the device. The manufacturer shall not be held legally responsible for inaccuracies, errors, or omissions in the manual or automatically set parameters for a device or for an incorrect application of a device. • Repairs may only be executed by the manufacturer. • Installation, operation, and maintenance procedures should only be carried out by qualified personnel. • Use of the device and its installation must be in accordance with national legal requirements and local electrical codes . • When working on devices the valid safety regulations must be observed. • The reader module is a limited module. The HF Reader IC has no internal shielding. The module is designed for installation in electronic devices. (e.g. printers, terminals, hand scanners, etc.) Care must be taken to ensure that no switching power supply, oscillator or high current lines are routed directly along the module. Or located under the module. Only the antennas, mentioned in the manual, may be used. The cable length to the an- tenna is limited to 1m. Take care that the PCB design in the host environmentis is EMC compliant. • Special advice for carriers of cardiac pacemakers: Although this device doesn't exceed the valid limits for electromagnetic fields you should keep a minimum distance of 25 cm between the external antenna and your cardi- ac pacemaker and not stay in an immediate proximity of the device respective the an- tenna for some time. IDENTIFICATION Installation ID CPR60 FEIG ELECTRONIC GmbH Page 5 of 16 CPR60_Installation M91210-0e_03.doc 2. Characterization ID CPR60 The ID CPR60 is a RFID reader which supports ISO/IEC 14443 A/B and ISO 15693 contactless smart cards and transponders. It also offers 4 interfaces to connect ISO 7816 smart cards with contacts. Three different antenn…

Text truncated - open the document above for the full version.

CONFIDENTIALITY REQUEST for Certification Service in USA Federal Communication Commission Equipment Authorization Division, Application Processing Branch 7435 Oakland Mills Road Columbia, MD 21048 23.03.2020 TO WHOM IT MAY CONCERN Pursuant to Paragraphs §0.457 and 0.459 of the Commission’s Rules (47 C.F.R.) and Section §552(b)(4) of the Freedom of Information Act, we requests confidentiality for the following products: FCC ID Number Product Title/Model FCC ID PJMCPR60 ID CPR60 1. Electrical Schematic • CPR60-Schematic_01.pdf (4 pages) • CPR60-Antenna_01.pdf (1 pages) 2. PCB Layout • ICPR60_PCB_01.pdf (3 pages) 3. Block Diagram • CPR60_Block Diagram_01.pdf (1 pages) 4. Bill of Material • CPR60_BOM_01.pdf (2 pages) 5. Description • CPR60_Operational Discription_02.pdf (1 pages) For the product stated above, we request permanent confidentiality for exhibits which contain Operational Description, Block Diagram, Schematics, Parts Lists or Tune Up Information. The above exhibits contain our trade secrets and proprietary information that could be of benefit to our competitors. If you have any questions, please feel free to contact me at the address shown below. Sincerely , Date: 23.03.2020 City: Weilburg _______________________________________ (Signature) Contact name: Bernhard Schüßler Company: FEIG ELECTRONIC GmbH Address: Lange Straße 4 / 35781 Weilburg, Germany Phone: 00 49 645 ́71/3109 0 Fax: 00 49 645 ́71/3109 99 Email: [email protected]

SHORT-TERM CONFIDENTIALITY REQUEST Federal Communication Commission Equipment Authorization Division, Application Processing Branch 7435 Oakland Mills Road Columbia, MD 21048 30.04.2020 TO WHOM IT MAY CONCERN Pursuant to Paragraphs §0.457 and 0.459 of the Commission’s Rules (47 C.F.R.) and Section §552(b)(4) of the Freedom of Information Act, we requests short term confidentiality for the following product: FCC ID Number Product Title/Model FCC ID PJMCPR60 ID CPR60 For the product stated above, we request that the following information be held confidential: 1. External and Internal Photographs 2. Test Setup Photos 3. User Manual We request this confidentiality on the basis of ensuring that business sensitive information remains confidential until the actual marketing of our new device, which is planned for 29.10.2020 If you have any questions, please feel free to contact me at the address shown below. Sincerely , (Signature) Contact name: Bernhard Schüßler Company: FEIG ELECTRONIC GmbH Address: Lange Straße 4 / 35781 Weilburg, Germany Phone: 00 49 645 ́71/3109 0 Fax: 00 49 645 ́71/3109 99 Email: [email protected]

Federal Communication Commission Equipment Authorization Division, Application Processing Branch 7435 Oakland Mills Road Columbia, MD 21048 Certification and Engineering Bureau Innovation, Science and Economic Development Canada Spectrum Engineering Branch 3701 Carling Avenue, Building 94 Ottawa, Ontario K2H 8S2 Subject: FCC / ISED Modular Approval Statement FCC ID: Only applicable for ISED certification: CN: (Company Number) UPN: (Unique Product Number) HVIN: (Hardware Version Identification Number) PMN: (Product Marketing Name) HMN: (Host Marketing Name) FVIN: (Firmware Version Identification Number) TO WHOM IT MAY CONCERN Pursuant to Paragraphs RSP-100, Issue 11 and CFR § 15.212, we herewith declare for our module. Modular approval requirement Yes No * (a) The radio elements must have the radio frequency circuitry be shielded. Physical/discrete and tuning capacitors may be located external to the shield, but must be on the module assembly. *Please provide a detailed explanation if the answer is “No.”: (b) The module shall have buffered modulation/data input(s) (if such inputs are provided) to ensure that the module will comply with the requirements set out in the applicable RSS of ISED and with part 15 of FCC under conditions of excessive data rates or over-modulation. *Please provide a detailed explanation if the answer is “No.”: (c) The module shall have its own power supply regulation on the module. This is to ensure that the module will comply with the requirements set out in the applicable standard regardless of the design of the power supplying circuitry in the host device which houses the module. *Please provide a detailed explanation if the answer is “No.”: (d) The module shall comply with the provisions for external power amplifiers and antennas detailed in the applicable RSS. The equipment certification submission shall contain a detailed description of highest antenna gain for each type of antenna. *Please provide a detailed explanation if the answer is “No.”: Modular Approval Attestation RSP-100, Issue 11, Annex D Check your CN here Check your GC here. Click "Grantee Search" Yes No * (e) The module shall be tested for compliance with the applicable standard in a stand-alone configuration, i.e. the module must not be inside another device during testing. *Please provide a detailed explanation if the answer is “No.”: (f) The module comply or will comply with applicable RSS-102 exposure requirements and any applicable FCC RF exposure requirement in its intended use/configurations. *Please provide a detailed explanation if the answer is “No.”: g) The module must be equipped with either a permanently affixed label or must be capable of electronically displaying its FCC identification number. *Please provide a detailed explanation if the answer is “No.”: Only applicable for FCC certification: (i) The modular transmitter complies with all applicable FCC rules. Instructions for maintaining compliance are given in the user instructions. If you have any questions, please feel free to contact us at the address shown below Best regards, INFO for applicant: Limited Modolar Approval (LMA) may be granted when one or more of the requirements in the table above cannot be demonstrated. LMA will also be issued in those instances where applicants can demonstrate that they will retain control over the final installation of the device, such that compliance of the end product is assured. In such cases, an operating condition on the LMA for the module must state that the module is only approved for use when installed in devices produced by a specific manufacturer. When LMA is sought, the application for equipment certification must specifically state how control of the end product, into which the module will be installed, will be maintained, such that full compliance of the end product is always ensured. Company Name: Phone: Company Address: Fax: E-mail: Contact Name: Signature: Signature Date: Document Version 1.0 2019-07-01

Photos ID CPR60 1 / 4 FCC ID: PJMCPR60 IC: 6633A-CPR60 Date : 10.03.2020 ID CPR60 Top Side Bottom Side Photos ID CPR60 2 / 4 FCC ID: PJMCPR60 IC: 6633A-CPR60 Date : 10.03.2020 ID ISC.ANT100/100 Top Side Bottom Side Photos ID CPR60 3 / 4 FCC ID: PJMCPR60 IC: 6633A-CPR60 Date : 10.03.2020 RFID Antenna Board 445-100302 Top Side Bottom Side Photos ID CPR60 4 / 4 FCC ID: PJMCPR60 IC: 6633A-CPR60 Date : 10.03.2020 ID ISC.ANT40/30 Top Side Bottom Side

Label ID CPR60 1 / 1 FCC ID: PJMCPR60 IC: 6633A-CPR60 Date : 23.03.2020 ID CPR60

Photos ID CPR60 1 / 4 FCC ID: PJMCPR60 IC: 6633A-CPR60 Date : 10.03.2020 ID CPR60 Top Side Bottom Side Photos ID CPR60 2 / 4 FCC ID: PJMCPR60 IC: 6633A-CPR60 Date : 10.03.2020 ID ISC.ANT100/100 Top Side Bottom Side Photos ID CPR60 3 / 4 FCC ID: PJMCPR60 IC: 6633A-CPR60 Date : 10.03.2020 RFID Antenna Board 445-100302 Top Side Bottom Side Photos ID CPR60 4 / 4 FCC ID: PJMCPR60 IC: 6633A-CPR60 Date : 10.03.2020 ID ISC.ANT40/30 Top Side Bottom Side

Annex A 1-0133/20-01-01-A_AnnexA External photos of the Equipment Under Test This addendum is electronically signed and valid without handwritten signature. For verification of the electronic signatures, the public keys can be requested at the testing laboratory. Document authorized: Tobias Wittenmeier Testing Manager Radio Communications & EMC CTC advanced GmbHUntertuerkheimer Str. 6-10 66117 Saarbruecken / Germany Phone: +49 681 5 98 - 0 Fax: +49 681 5 98 - 9075 web: ctcadvanced.com e-mail: [email protected] Photos Photo 1 Photo 2 2020-03-17Document No. 1-0133/20-01-01-A_AnnexA2/7 Photo 3 Photo 4 2020-03-17Document No. 1-0133/20-01-01-A_AnnexA3/7 Photo 5 Photo 6 2020-03-17Document No. 1-0133/20-01-01-A_AnnexA4/7 Photo 7 Photo 8 2020-03-17Document No. 1-0133/20-01-01-A_AnnexA5/7 Photo 9 2020-03-17Document No. 1-0133/20-01-01-A_AnnexA6/7 Document history VersionApplied changesDate of release initial release2020-03-17 - END OF DOCUMENT - 2020-03-17Document No. 1-0133/20-01-01-A_AnnexA7/7

BNetzA - CAB - 02/21 - 102 TEST REPORT Test report no.: 1-0133/20-01-02-A Testing laboratory Applicant CTC advanced GmbH Untertuerkheimer Strasse 6 – 10 66117 Saarbruecken / Germany Phone: + 49 681 5 98 - 0 Fax: + 49 681 5 98 - 9075 Internet: http://www.ctcadvanced.com e-mail: [email protected] Accredited Testing Laboratory: The testing laboratory (area of testing) is accredited according to DIN EN ISO/IEC 17025 (2005) by the Deutsche Akkreditierungsstelle GmbH (DAkkS) The accreditation is valid for the scope of testing procedures as stated in the accreditation certificate starting with the registration number: D-PL-12076-01. FEIG ELECTRONIC GmbH Lange Str. 4 35781 Weilburg / GERMANY Phone: +49 6471 31 09-0 Contact: Bernhard Schüßler e-mail: [email protected] Phone: +49 6471 310-9435 Manufacturer FEIG ELECTRONIC GmbH Lange Str. 4 35781 Weilburg / GERMANY Test standard/s FCC - Title 47 CFR Part 15 FCC - Title 47 of the Code of Federal Regulations; Chapter I; Part 15 - Radio frequency devices RSS - 210 Issue 10 Spectrum Management and Telecommunications Radio Standards Specification - Licence-Exempt Radio Apparatus: Category I Equipment RSS - Gen Issue 5 incl. Amendment 1 Spectrum Management and Telecommunications Radio Standards Specification - General Requirements for Compliance of Radio Apparatus For further applied test standards please refer to section 3 of this test report. Test Item Kind of test item: RFID Reader Model name: ID CPR60-A with 3 antennas FCC ID: PJMCPR60 IC: 6633A-CPR60 Frequency: 13.56 MHz Technology tested: RFID Antenna: 3 external PCB loop coil antennas Antenna 1 (100 x 100mm) ID ISC.ANT100/100 Antenna 2 (40 x 30mm) ID ISC.ANT40/30 Antenna 3 (30 x 30mm) RFID Antenna Board 445-100302 Power supply: 10.2 V to 13.8 V DC by external power supply Temperature range: -25°C to +70°C This test report is electronically signed and valid without handwritten signature. For verification of the electronic signatures, the public keys can be requested at the testing laboratory. Test report authorized: Test performed: p.o. Christoph Schneider Tobias Wittenmeier Lab Manager Testing Manager Radio Communications Radio Communications Test report no.: 1-0133/20-01-02-A © CTC advanced GmbH Page 2 of 36 1 Table of contents 1 Table of contents ............................................................................................................................................ 2 2 General information ....................................................................................................................................... 3 2.1 Notes and disclaimer .......................................................................................................................... 3 2.2 Application details ............................................................................................................................... 3 2.3 Test laboratories sub-contracted ...................................................................................................... 3 3 Test standard/s, references and accreditations .......................................................................................... 4 4 Test environment ............................................................................................................................................ 5 5 Test item .......................................................................................................................................................... 5 5.1 General description ............................................................................................................................. 5 5.2 Additional information ........................................................................................................................ 5 6 Description of the test setup ......................................................................................................................... 6 6.1 Shielded semi anechoic chamber ...................................................................................................... 7 6.2 Shielded fully anechoic chamber ...................................................................................................... 9 6.3 AC conducted .................................................................................................................................... 10 6.4 RF measurements normal and extreme conditions ....................................................................... 11 7 Sequence of testing ..................................................................................................................................... 12 7.1 Sequence of testing radiated spurious 9 kHz to 30 MHz ............................................................... 12 7.2 Sequence of testing radiated spurious 30 MHz to 1 GHz .............................................................. 13 8 Measurement uncertainty ............................................................................................................................ 14 9 Summary of measurement results ............................................................................................................. 15 10 Additional comments ............................................................................................................................... 15 11 Measurement results ................................................................................................................................ 16 11.1 Occupied bandwidth ...................................................................................................................... 16 11.2 Field strength of the fundamental ................................................................................................ 18 11.3 Field strength of the harmonics and spurious ........................................................................... 19 11.4 Conducted limits ................…

Text truncated - open the document above for the full version.

Annex D 1-0133/20-01-01_AnnexD Setup photos of the Equipment Under Test This addendum is electronically signed and valid without handwritten signature. For verification of the electronic signatures, the public keys can be requested at the testing laboratory. Document authorized: Tobias Wittenmeier Testing Manager Radio Communications & EMC CTC advanced GmbHUntertuerkheimer Str. 6-10 66117 Saarbruecken / Germany Phone: +49 681 5 98 - 0 Fax: +49 681 5 98 - 9075 web: ctcadvanced.com e-mail: [email protected] Photos Photo 1 Photo 2 2020-03-17Document No. 1-0133/20-01-01_AnnexD2/10 Photo 3 Photo 4 2020-03-17Document No. 1-0133/20-01-01_AnnexD3/10 Photo 5 Photo 6 2020-03-17Document No. 1-0133/20-01-01_AnnexD4/10 Photo 7 Photo 8 2020-03-17Document No. 1-0133/20-01-01_AnnexD5/10 Photo 9 Photo 10 2020-03-17Document No. 1-0133/20-01-01_AnnexD6/10 Photo 11 Photo 12 2020-03-17Document No. 1-0133/20-01-01_AnnexD7/10 Photo 13 Photo 14 2020-03-17Document No. 1-0133/20-01-01_AnnexD8/10 Photo 15 2020-03-17Document No. 1-0133/20-01-01_AnnexD9/10 Document history VersionApplied changesDate of release initial release2020-03-17 - END OF DOCUMENT - 2020-03-17Document No. 1-0133/20-01-01_AnnexD10/10