PP23362Multi-mode Wireless Keyboard

Shenzhen Rapoo Technology Co., Ltd 22, Jinxiu Road East, Pingshan District, Shenzhen, China Date: 2026-01-23 Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 Ref: Attestation Statements Part 2.911(d) (5) (i) Filing FCC ID: PP23362 To Whom It May Concern: Shenzhen Rapoo Technology Co., Ltd certifies that the equipment for which authorization is sought is not “covered” equipment prohibited from receiving an equipment authorization pursuant to section 2.903 of the FCC rules. Shenzhen Rapoo Technology Co., Ltd certifies that the equipment for which authorization is sought does not include cybersecurity or anti-virus software produced or provided by Kaspersky Lab, Inc. or any of its successors and assignees, including equipment with integrated Kaspersky Lab, Inc. (or any of its successors and assignees) cybersecurity or anti-virus software pursuant to DA-24-886 and KDB 986446 D01 Covered Equipment Guidance section B(2a). Device is inherently compliant based on hardware limitations or software controls. or A Software Bill of Materials (SBOM) is provided to the TCB for review, and The end-user or third parties cannot install additional software on this device. Sincerely, Signatory [Jerry Guo, Director of Research and Development Centre]

Shenzhen Rapoo Technology Co., Ltd 22, Jinxiu Road East, Pingshan District, Shenzhen, China Date: 2026-01-23 Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 USA Ref: Attestation Statements Part 2.911(d) (5) (ii) Filing FCC ID: PP23362 To Whom It May Concern: Shenzhen Rapoo Technology Co., Ltd certifies that, as of the date of the filing of the application, the applicant is not identified on the Covered List (as a specifically named entity or any of its subsidiaries or affiliates) as an entity producing “covered” equipment. Sincerely, Signatory [Jerry Guo, Director of Research and Development Centre]

Shenzhen Rapoo Technology Co., Ltd 22, Jinxiu Road East, Pingshan District, Shenzhen, China Date: 2026-01-23 Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 USA FCC ID: PP23362 Applicant FRN: 0017901232 US Agent – Attestation Statement / Part 2.911(d)(7) Shenzhen Rapoo Technology Co., Ltd certifies that, as of 2026-01-23, we have designated FCC US Agent, LLC to accept service of process on our behalf for FCC ID: PP23362. Shenzhen Rapoo Technology Co., Ltd, accepts to maintain an agent of service of process in the United States for no less than one year after either the grantee has permanently terminated all marketing and importation of the applicable equipment within the U.S., or the conclusion of any Commission-related administrative or judicial proceeding involving the equipment, whichever is later. FCC US Agent, LLC, accepts as of the date of the filing of this application, the obligation of being the designated agent for the purpose of accepting service of process on behalf of Shenzhen Rapoo Technology Co., Ltd for FCC ID: PP23362. Designated Agent Information: Company Name: FCC US Agent, LLC U.S. Agent FRN: 0033402884 Address: 3722 Illinois Avenue, Saint Charles, IL, 60174, USA Contact Person: Tim Payne Phone: 708-571-3148 Email: [email protected] Sincerely, Company: Shenzhen Rapoo Technology Co., Ltd Designated Agent: FCC US Agent, LLC Company Representative: Jerry Guo Designated Agent Representative: Tim Payne Signature: Signature:

Shenzhen Rapoo Technology Co., Ltd 22, Jinxiu Road East, Pingshan District, Shenzhen, China Date: 2026-01-23 FEDERAL COMMUNICATIONS COMMISSION AUTHORIZATION AND EVALUATION DIVISION 7435 OAKLAND MILLS ROAD COLUMBIA, MD 21046 SUBJECT: FCC Application for FCC ID: PP23362 Confidentiality Request To whom it may concern, Pursuant to the provisions of the Commission’s rules Title 47 Sections §0.457 and §0.459, we are requesting the Commission to withhold the following attachment(s) as confidential documents from public disclosure indefinitely. ☒ Block Diagram ☐ Tune-Up Information ☒ Operational Description, SBOM ☐ Security Information ☒ Schematics ☐ Software Defined Radio (SDR) Information ☐ Parts List The above materials contain trade secrets and proprietary information not customarily released to the public. The public disclosure of these materials may be harmful to the applicant and provide unjustified benefits to its competitors. In additional to above mentioned documents, in order to comply with the marketing regulations in Title 47 CFR §2.803 and the importation rules in Title 47 CFR §2.1204, while ensuring that business sensitive information remains confidential until the actual marketing of newly authorized devices, we request Short Term Confidentiality of the following attachment(s); ☒ External Photos ☒ Test Setup Photos ☒ Internal Photos ☒ User Manual ☐ For 45 days, pursuant to Public Notice DA 04-1705. or ☒ For 180 days pursuant to KDB 726920 D01. The applicant understands that pursuant to Section 0.457 of the Rules, disclosure of this application and all accompanying documentation will not be made before the date of the Grant for this application. Sincerely, Signatory [Jerry Guo, Director of Research and Development Centre]

Shenzhen Rapoo Technology Co., Ltd 22, Jinxiu Road East, Pingshan District, Shenzhen, China Date: 2026-01-23 FEDERAL COMMUNICATIONS COMMISSION AUTHORIZATION AND EVALUATION DIVISION 7435 OAKLAND MILLS ROAD COLUMBIA, MD 21046 SUBJECT: FCCID: PP23362 Model Declaration Letter Dear Regulatory Authority, Model(s): E900T,E2810M are same to the model 0212V-01, these models are same PCB Layout, Schematics, BOM. Only for different model name, appearance color for different market require. Sincerely, Signatory [Jerry Guo, Director of Research and Development Centre]

Shenzhen Rapoo Technology Co., Ltd 22, Jinxiu Road East, Pingshan District, Shenzhen, China Date: 2026-01-23 FEDERAL COMMUNICATIONS COMMISSION AUTHORIZATION AND EVALUATION DIVISION 7435 OAKLAND MILLS ROAD COLUMBIA, MD 21046 SUBJECT: FCC Application for FCC ID: PP23362 POWER OF ATTORNEY To Whom It May Concern: We, the undersigned, hereby authorize Waltek Testing Group (Shenzhen) Co., Ltd. Jandy So on our behalf, to apply to the Federal Communications Commission on our equipment. Any and all acts carried out by Waltek Testing Group (Shenzhen) Co., Ltd. Jandy So on our behalf shall have the same effect as acts of our own. This is to advise that we are in full compliance with the Anti-Drug Abuse Act. We, Shenzhen Rapoo Technology Co., Ltd are not subject to a denial of federal benefits pursuant to Section 5301 of the Anti-Drug Act of 1988, 21 USC853a, and no party to the application is subject to a denial of federal benefits pursuant to that section. Sincerely, Signatory [Jerry Guo, Director of Research and Development Centre]

Shenzhen Rapoo Technology Co., Ltd 22, Jinxiu Road East, Pingshan District, Shenzhen, China Responsibility Declaration Letter v1.0 Responsibility Declaration Letter Company name: Shenzhen Rapoo Technology Co., Ltd Address: 22, Jinxiu Road East, Pingshan District, Shenzhen, China Product Name: Multi-mode Wireless Keyboard FCC ID: PP23362 Model(s): 0212V-01, E900T,E2810M We, Shenzhen Rapoo Technology Co., Ltd hereby acknowledge that all the product information (including all original, drafted, or modified documents) provided to the TCB either by us or our agent or representative(s) for the purposes of FCC certification will meet FCC regulations and requirements; and that any modifications or changes made as a result of TCB review of the documents will be formally implemented into the manufacturing process and product documentation shipped with equipment. We also confirm that all information provided is legitimate and does not contain any false content such as forgery, fabrication, alteration, tampering and concealment. We assume all economic and legal responsibilities in matters that may arise as a result of disclosure on sample products and associated product documentation provided for product certification that may subsequently be found to be a mis-representation of the final product and accompanying documentation when produced, marketed, or sold in the United States, Canada, or anywhere in the world. Your sincerely, Name: Jerry Guo Date: 2026-01-23 Title and Company name: Director of Research and Development Centre, Shenzhen Rapoo Technology Co., Ltd Signature of FCC grant holder (Include Title, Company name, date, and official company stamp):

Shenzhen Rapoo Technology Co., Ltd 22, Jinxiu Road East, Pingshan District, Shenzhen, China Agent Authorization Company: Shenzhen Rapoo Technology Co., Ltd Address: 22, Jinxiu Road East, Pingshan District, Shenzhen, China Product Name: Multi-mode Wireless Keyboard Model Number(s): 0212V-01, E900T,E2810M Product Description: Multi-mode Wireless Keyboard We authorize MiCOM Labs Inc., 575 Boulder Court, Pleasanton, California 94566, USA, to act on our behalf on all matters concerning the certification of above named equipment. We declare that MiCOM Labs Inc. is allowed to forward all information related to the approval and certification of equipment to the regulatory agencies as required and to discuss any issues concerning the approval application. Any and all acts carried out by MiCOM Labs on our behalf shall have the same effect as acts of our own. Signature: Date: 2026-01-23 Name: Jerry Guo Title: Director of Research and Development Centre Company: Shenzhen Rapoo Technology Co., Ltd

Reference No.: WTX25X11306629W001/002 Page 1 of 14 Waltek Testing Group (Shenzhen) Co., Ltd. Http://www.waltek.com.cn ANNEX EXHIBIT 1 - PRODUCT LABELING Proposed FCC ID Label Format Specifications: The label shall be securely affixed to a permanently attached part of the device, in a location where it is visible or easily accessible to the user, and shall not be readily detachable. The label shall be sufficiently durable to remain fully legible and intact on the device in all normal conditions of use throughout the device’s expected lifetime. Proposed Label Location on EUT FCC ID Label Location

1. RF Exposure Requirements 1.1 General Information Client Information Applicant: ShenZhen Rapoo Technology Co., Ltd. Address of applicant: 22,Jinxiu Road East,Pingshan District,Shenzhen,China Manufacturer: ShenZhen Rapoo Technology Co., Ltd. Address of manufacturer: 22,Jinxiu Road East,Pingshan District,Shenzhen,China General Description of EUT: Product Name: Multi-mode Wireless Keyboard Trade Name RAPOO Model No.: 0212V-01 Adding Model(s): E900T,E2810M Rated Voltage: Battery DC 3V Power Adapter: / FCC ID: PP23362 Equipment Type: Portable device Technical Characteristics of EUT: Bluetooth Bluetooth Version: V5.0 (LE mode) Frequency Range: 2402-2480MHz RF Output Power: 1Mbps: 3.16dBm (Conducted) 2Mbps: 2.68dBm (Conducted) Data Rate: 1Mbps, 2Mbps Modulation: GFSK Quantity of Channels: 40 Channel Separation: 2MHz Type of Antenna: PCB Antenna Antenna Gain: -5.68dBi SRD 2.4G Frequency Range: 2405MHz-2478MHz Max. Field Strength: 52.63dBuV/m Modulation: GFSK Quantity of Channels: 8 Channel Separation: / Antenna Type: PCB Antenna Antenna Gain: -5.68dBi 1.2 RF Exposure Exemption According to §1.1307(b)(3) and KDB 447498 D04 Interim General RF Exposure Guidance v01, system operating under the provisions of this section shall be operating in a manner that the public is not exposed to radio frequency energy level in excess limit for maximum permissible exposure. Option A: FCC Rule Part 1.1307 (b)(3)(i)(A):The available maximum time-averaged power is no more than 1mW, regardless of separation distance. Option B: FCC Rule Part 1.1307 (b)(3)(i)(B): The available maximum time-averaged power or effective radiated power (ERP), whichever is greater, is less than or equal to the threshold P th (mW) described in the following formula. P th is given by: Option C: FCC Rule Part 1.1307 (b)(3)(i)(C): The minimum separation distance (R in meters) from the body of a nearby person for the frequency (f in MHz) at which the source operates, the ERP (watts) is no more than the calculated value prescribed for that frequency. R must be at least λ/2π, where λ is the free-space operating wavelength in meters. Single RF Sources Subject to Routine Environmental Evaluation RF Source frequency (MHz) Threshold ERP (watts) 0.3-1.34 1,920 R 2 1.34-30 3,450 R 2 /f 2 30-300 3.83 R 2 300-1,500 0.0128 R 2 f 1,500-100,000 19.2R 2 For Multiple RF sources: FCC Rule Part 1.1307(b)(3)(ii): (A) The available maximum time-averaged power of each source is no more than 1 mW and there is a separation distance of two centimeters between any portion of a radiating structure operating and the nearest portion of any other radiating structure in the same device, except if the sum of multiple sources is less than 1 mW during the time-averaging period, in which case they may be treated as a single source (separation is not required). (B) In the case of fixed RF sources operating in the same time-averaging period, or of multiple mobile or portable RF sources within a device operating in the same time averaging period, if the sum of the fractional contributions to the applicable thresholds is less than or equal to 1 as indicated in the following equation. 1.3 Calculated Result Radio Access Technology Prediction Frequency Output Power Antenna Gain Duty Cycle Tune-Up Time-Averaged Power ERP (MHz) (dBm) (dBi) (%) (dBm) (dBm) Bluetooth 2402 3.16 -5.68 100 4.00 -3.83 SRD 2.4G 2405 -36.95 -5.68 / -36.00 -43.83 Frequency Option Min. Distance Max. Power Exposure Limit Ratio Result (MHz) (cm) (dBm) (mW) (mW) Pass/Fail 2402 B 0.5 4.00 2.51 2.788 0.90 Pass 2405 B 0.5 -36.00 0.00 2.785 0.01 Pass Note: 1. Time-Averaged Power=Output Power * Duty Cycle; ERP= Time-Averaged Power+ Antenna gain-2.15dB 2. Option A, B and C refers as clause 1.2. 3. For option B, Max (time-averaged power, effective radiated power (ERP)) converts to Max. Power. For option C, ERP converts to Max. Power; 4. For option B, P th (mW) converts to Exposure Limit (mW); For option C, ERP (W) converts to Exposure Limit (mW). 5. Ratio= Tune-Up ERP (mW)/ Exposure Limit (mW) Mode for Simultaneous Multi-band Transmission: Radio Access Technology Ratio 1 Ratio 2 Simultaneous Ratio Limit Result Pass/Fail -- -- -- -- -- -- Note: Bluetooth and SRD 2.4G can’t transmit at the same time. Result: Pass

Report No.: BL-SZ21C0435-906 2 / 12 Revision History Version Issue Date Revisions Rev. 01 Dec. 15, 2021 Initial Issue TABLE OF CONTENTS 1 Administrative Data (GENERAL INFORMATION) ................................................................................... 3 1.1 Identification of the Testing Laboratory ............................................................................................. 3 1.2 Identification of the Responsible Testing Location ............................................................................ 3 1.3 Laboratory Condition ......................................................................................................................... 3 1.4 Announce .......................................................................................................................................... 3 2 PRODUCT INFORMATION ..................................................................................................................... 4 2.1 Applicant Information ........................................................................................................................ 4 2.2 Manufacturer Information .................................................................................................................. 4 2.3 Factory Information ........................................................................................................................... 4 2.4 General Description for Equipment under Test (EUT) ...................................................................... 4 2.5 Ancillary Equipment .......................................................................................................................... 4 2.6 Technical Information ........................................................................................................................ 4 3 SUMMARY OF TEST RESULTS ............................................................................................................. 5 3.1 Test Standards .................................................................................................................................. 5 3.2 Test Verdict ....................................................................................................................................... 5 3.3 Test Uncertainty ................................................................................................................................ 5 4 GENERAL TEST CONFIGURATIONS .................................................................................................... 6 4.1 Test Condition ................................................................................................................................... 6 4.2 Test Equipment List .......................................................................................................................... 6 4.3 Test Setup ......................................................................................................................................... 6 ANNEX A TEST RESULTS ......................................................................................................................... 7 A.1 Gain and Efficiency ........................................................................................................................... 7 ANNEX B RADIATION PATTERN .............................................................................................................. 8 ANNEX C TEST SETUP PHOTO ............................................................................................................. 11 ANNEX D EUT PHOTO ............................................................................................................................ 12 Report No.: BL-SZ21C0435-906 3 / 12 1 Administrative Data (GENERAL INFORMATION) 1.1 Identification of the Testing Laboratory Company Name Shenzhen BALUN Technology Co., Ltd. Address Block B, 1st FL, Baisha Science and Technology Park, Shahe Xi Road, Nanshan District, Shenzhen, Guangdong Province, P. R. China Phone Number +86 755 6685 0100 1.2 Identification of the Responsible Testing Location Test Location Shenzhen BALUN Technology Co., Ltd. Address Block B, 1st FL, Baisha Science and Technology Park, Shahe Xi Road, Nanshan District, Shenzhen, Guangdong Province, P. R. China Description All measurement facilities used to collect the measurement data are located at Block B, FL 1, Baisha Science and Technology Park, Shahe Xi Road, Nanshan District, Shenzhen, Guangdong Province, P. R. China 518055 1.3 Laboratory Condition Ambient Temperature 19°C to 25°C Ambient Relative Humidity 45% to 55% Ambient Pressure 100 kPa to 102 kPa 1.4 Announce (1) The test report reference to the report template version v2.2. (2) The test report is invalid if not marked with the signatures of the persons responsible for preparing and approving the test report. (3) The test report is invalid if there is any evidence and/or falsification. (4) The results documented in this report apply only to the tested sample, under the conditions and modes of operation as described herein. (5) This document may not be altered or revised in any way unless done so by BALUN and all revisions are duly noted in the revisions section. (6) Content of the test report, in part or in full, cannot be used for publicity and/or promotional purposes without prior written approval from the laboratory. (7) The laboratory is only responsible for the data released by the laboratory, except for the part provided by the applicant. Report No.: BL-SZ21C0435-906 4 / 12 2 PRODUCT INFORMATION 2.1 Applicant Information Applicant ShenZhen Rapoo Technology Co., Ltd. Address 22, Jinxiu Road East, Pingshan District, Shenzhen, China Contact Person guirongtang Telephone Number 13873962693 Fax Number 07552858 8958 E-mail Address [email protected] 2.2 Manufacturer Information Manufacturer ShenZhen Rapoo Technology Co., Ltd. Address 22, Jinxiu Road East, Pingshan Distri…

Text truncated - open the document above for the full version.

Waltek Testing Group (Shenzhen) Co., Ltd. Http://www.waltek.com.cn Page 1 of 57 TEST REPORT Reference No. ....................: WTX25X11306629W001 FCC ID ............................... .: PP23362 Applicant .......................... .: ShenZhen Rapoo Technology Co., Ltd. Address ............................ .: 22,Jinxiu Road East,Pingshan District,Shenzhen,China Manufacturer .................... .: The same as Applicant Address ............................ .: The same as Applicant Product Name .................. .: Multi-mode Wireless Keyboard Model No.. ......................... .: 0212V-01 Standards ......................... .: FCC Part 15.247 Date of Receipt sample ... .: 2025-11-20 Date of Test....................... .: 2025-11-22 to 2026-01-14 Date of Issue .................... .: 2026-01-16 Test Report Form No. ...... . : WTX_Part 15_247W Test Result ........................ .: Pass Remarks: The results shown in this test report refer only to the sample(s) tested, this test report cannot be reproduced, except in full, without prior written permission of the company. The report would be invalid without specific stamp of test institute and the signatures of approver. Prepared By: Waltek Testing Group (Shenzhen) Co., Ltd. Address: 1/F., Room 101, Building 1, Hongwei Industrial Park, Liuxian 2nd Road, Block 70 Bao'an District, Shenzhen, Guangdong, China Tel.: +86-755-33663308 Fax.: +86-755-33663309 Email: [email protected] Tested by: Approved by: Gala Wang/Project Engineer Jason Su/Manager Reference No.: WTX25X11306629W001 Waltek Testing Group (Shenzhen) Co., Ltd. Http://www.waltek.com.cn Page 2 of 57 TABLE OF CONTENTS 1. GENERAL INFORMATION .................................................................................................................................... 4 1.1 PRODUCT DESCRIPTION FOR EQUIPMENT UNDER TEST (EUT) ......................................................................... 4 1.2 TEST STANDARDS ................................................................................................................................................. 5 1.3 TEST METHODOLOGY ........................................................................................................................................... 5 1.4 TEST FACILITY ...................................................................................................................................................... 5 1.5 EUT SETUP AND TEST MODE .............................................................................................................................. 6 1.6 MEASUREMENT UNCERTAINTY ............................................................................................................................. 7 1.7 TEST EQUIPMENT LIST AND DETAILS ................................................................................................................... 8 2. SUMMARY OF TEST RESULTS ......................................................................................................................... 12 3. ANTENNA REQUIREMENT ................................................................................................................................. 13 3.1 STANDARD APPLICABLE ..................................................................................................................................... 13 3.2 EVALUATION INFORMATION ................................................................................................................................ 13 4. POWER SPECTRAL DENSITY ........................................................................................................................... 14 4.1 STANDARD APPLICABLE ..................................................................................................................................... 14 4.2 TEST SETUP BLOCK DIAGRAM ........................................................................................................................... 14 4.3 TEST PROCEDURE .............................................................................................................................................. 14 4.4 SUMMARY OF TEST RESULTS/PLOTS ................................................................................................................. 14 5. DTS BANDWIDTH ................................................................................................................................................. 15 5.1 STANDARD APPLICABLE ..................................................................................................................................... 15 5.2 TEST SETUP BLOCK DIAGRAM ........................................................................................................................... 15 5.3 TEST PROCEDURE .............................................................................................................................................. 15 5.4 SUMMARY OF TEST RESULTS/PLOTS ................................................................................................................. 15 6. RF OUTPUT POWER ............................................................................................................................................ 16 6.1 STANDARD APPLICABLE ..................................................................................................................................... 16 6.2 TEST SETUP BLOCK DIAGRAM ........................................................................................................................... 16 6.3 TEST PROCEDURE .............................................................................................................................................. 16 6.4 SUMMARY OF TEST RESULTS/PLOTS ................................................................................................................. 16 7. FIELD STRENGTH OF SPURIOUS EMISSIONS ............................................…

Text truncated - open the document above for the full version.