PR4FLUSHP2MTMicrowave Oven

Whirlpool Microwave Products Development Limited. Address: 17th Fl, Elite Centre,22 Hung To Rd,Kwun Tong, Hong Kong Tel: 8675583811688 Email: [email protected] CFR 47 §2.911(d)(5)(i) Attestation Letter Attestation Letter Date: 2023-7-17 FEDERAL COMMUNICATIONS COMMISSIONS Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 Ref: Attestation Statements CFR 47 §2.911(d)(5)(i) Filing FCC ID: PR4FLUSHP2MT Whirlpool Microwave Products Development Limited. certifies that the equipment for which authorization is sought, is not “covered” equipment prohibited from receiving an equipment authorization pursuant to section 2.903 of the FCC rules. Sincerely, Signature: Bobo Lin Approbation Manager

Whirlpool Microwave Products Development Limited. Address: 17th Fl, Elite Centre,22 Hung To Rd,Kwun Tong, Hong Kong Tel: 8675583811688 Email: [email protected] CFR 47 §2.911 (d)(5)(ii) Attestation Letter Attestation Letter Date: 2023-7-17 FEDERAL COMMUNICATIONS COMMISSIONS Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 Ref: Attestation Statements CFR 47 §2.911(d)(5)(ii) Filing FCC ID: PR4FLUSHP2MT Whirlpool Microwave Products Development Limited. certifies that as of the date of the filing of the application, the applicant is not identified on the Covered List as an entity producing “covered” equipment. Sincerely, Signature: Bobo Lin Approbation Manager

U.S. AGENT LETTER OF ATTESTATION Date: 2023-7-17 FEDERAL COMMUNICATIONS COMMISSION Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 Ref: Attestation Statements CFR 47 §2.911(d)(7) Filing FCC ID: PR4FLUSHP2MT Whirlpool Microwave Products Development Limited. certifies that, as of the date of the filing of the application, Whirlpool Corporation is our designated U.S. agent for service of process for the above referenced FCC ID. Whirlpool Microwave Products Development Limited. accepts to maintain an agent for no less than one year after the grantee has terminated all marketing and importation or the conclusion of any Commission-related proceeding involving the equipment. Whirlpool Corporation accepts, as of the date of the filing of the application, the obligation of the designated U.S. agent for service of process for the above referenced FCC ID. Designated U.S. Agent Information: Name: Whirlpool Corporation Address: 2000 N M-63, MD 4300, Benton Harbor, MI, 49022, USA FRN: 0011042405 Tel.: 918-697-1336 Email: [email protected] Signed by (printed name): Cammie Rhodes Signature: Applicant: Whirlpool Microwave Products Development Limited. Address: 17th Fl, Elite Centre,22 Hung To Rd,Kwun Tong, Hong Kong FRN: 0012635595 Tel: 8675583811688 Email: [email protected] Signed by (printed name): Bobo Lin Signature:

Whirlpool Microwave Products Development Limited. Address: 17th Fl, Elite Centre,22 Hung To Rd,Kwun Tong, Hong Kong Tel: 8675583811688 Email: [email protected] QA-FR-170-B FCC Authorization Date: 2023-7-17 FEDERAL COMMUNICATIONS COMMISSIONS Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 Subject: Agent Authorization To whom it may concern: We, Whirlpool Microwave Products Development Limited., the undersigned, hereby authorizes Shenzhen Accurate Technology Co., Ltd. to act on its behalf in all matters relating to application for Equipment authorization, including the signing of all documents relating to these matters. All acts carried out by Shenzhen Accurate Technology Co., Ltd. on our behalf shall have the same effect as our own action. We, the undersigned, hereby certify that we are not subject to a denial of federal benefits, that includes FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C. 862. This authorization is valid until further written notice from the applicant. Sincerely Yours, Signature: Bobo Lin Approbation Manager

Whirlpool Microwave Products Development Limited. Address: 17th Fl, Elite Centre,22 Hung To Rd,Kwun Tong, Hong Kong Tel: 8675583811688 Email: [email protected] FCC Confidential Authorization Date: 2023-7-17 FEDERAL COMMUNICATIONS COMMISSIONS Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 Subject: Confidentiality Request regarding application for certification of FCC ID: PR4FLUSHP2MT In accordance with Sections 0.457 and 0.459 of the Commission’s Rules, Whirlpool Microwave Products Development Limited. hereby requests long-term confidential treatment of information accompanying this application as outlined below:  Block Diagram  Schematics  Operation Description The above materials contain proprietary and confidential information not customarily released to the public. The public disclosure of these materials provides unjustified benefits to its competitors in the market. Sincerely Yours, Signature: Bobo Lin Approbation Manager

Shenzhen Accurate Technology Co., Ltd. Project No.: RA230625-36010E-EM-01 External Photos Page 1 of 4 External Photos Shenzhen Accurate Technology Co., Ltd. Project No.: RA230625-36010E-EM-01 External Photos Page 2 of 4 Shenzhen Accurate Technology Co., Ltd. Project No.: RA230625-36010E-EM-01 External Photos Page 3 of 4 Shenzhen Accurate Technology Co., Ltd. Project No.: RA230625-36010E-EM-01 External Photos Page 4 of 4

Shenzhen Accurate Technology Co., Ltd. Project No.: RA230625-36010E-EM-01 EXHIBITA-FCC ID LABEL AND LOCATION FCC ID Label FCC ID Label Location Information The label shown shall be permanently affixed at a conspicuous location on the device and be readily visible tothe time purchase (Labeling requirements per 2.295)

Shenzhen Accurate Technology Co., Ltd. Project No.: RA230625-36010E-EM-01 Internal Photos Page 1 of 18 Internal Photos Shenzhen Accurate Technology Co., Ltd. Project No.: RA230625-36010E-EM-01 Internal Photos Page 2 of 18 Shenzhen Accurate Technology Co., Ltd. Project No.: RA230625-36010E-EM-01 Internal Photos Page 3 of 18 Shenzhen Accurate Technology Co., Ltd. Project No.: RA230625-36010E-EM-01 Internal Photos Page 4 of 18 Shenzhen Accurate Technology Co., Ltd. Project No.: RA230625-36010E-EM-01 Internal Photos Page 5 of 18 Shenzhen Accurate Technology Co., Ltd. Project No.: RA230625-36010E-EM-01 Internal Photos Page 6 of 18 Shenzhen Accurate Technology Co., Ltd. Project No.: RA230625-36010E-EM-01 Internal Photos Page 7 of 18 Shenzhen Accurate Technology Co., Ltd. Project No.: RA230625-36010E-EM-01 Internal Photos Page 8 of 18 Shenzhen Accurate Technology Co., Ltd. Project No.: RA230625-36010E-EM-01 Internal Photos Page 9 of 18 Shenzhen Accurate Technology Co., Ltd. Project No.: RA230625-36010E-EM-01 Internal Photos Page 10 of 18 Shenzhen Accurate Technology Co., Ltd. Project No.: RA230625-36010E-EM-01 Internal Photos Page 11 of 18 Shenzhen Accurate Technology Co., Ltd. Project No.: RA230625-36010E-EM-01 Internal Photos Page 12 of 18 Shenzhen Accurate Technology Co., Ltd. Project No.: RA230625-36010E-EM-01 Internal Photos Page 13 of 18 Shenzhen Accurate Technology Co., Ltd. Project No.: RA230625-36010E-EM-01 Internal Photos Page 14 of 18 Shenzhen Accurate Technology Co., Ltd. Project No.: RA230625-36010E-EM-01 Internal Photos Page 15 of 18 Shenzhen Accurate Technology Co., Ltd. Project No.: RA230625-36010E-EM-01 Internal Photos Page 16 of 18 Wi-Fi Module FCC ID:2AC7Z-RIGEL PCB antenna 1 PCB antenna 2 Shenzhen Accurate Technology Co., Ltd. Project No.: RA230625-36010E-EM-01 Internal Photos Page 17 of 18 Shenzhen Accurate Technology Co., Ltd. Project No.: RA230625-36010E-EM-01 Internal Photos Page 18 of 18

Shenzhen Accurate Technology Co., Ltd. Report No.: RA230625-36010E-EM-01 Version 27: 2023-01-30 Page 11 of 27 FCC-EMC FCC §18.313, §1.1310, §2.1091 - MAXIMUM PERMISSIBLE EXPOSURE Applicable Standard According to subpart §1.1310, systems operating under the provisions of this section shall be operated in a manner that ensures that the public is not exposed to radio frequency energy level in excess of the Commission’s guidelines. Limits for Maximum Permissible Exposure (MPE) (§1.1310, §2.1091) (B) Limits for General Population/Uncontrolled Exposure Frequency Range (MHz) Electric Field Strength (V/m) Magnetic Field Strength (A/m) Power Density (mW/cm 2 ) Averaging Time (minutes) 0.3–1.34 614 1.63 *(100) 30 1.34–30 824/f 2.19/f *(180/f²) 30 30–300 27.5 0.073 0.2 30 300–1500 / / f/1500 30 1500–100,000 / / 1.0 30 f = frequency in MHz; * = Plane-wave equivalent power density; Measurement Environmental Conditions Temperature: 23 °C Relative Humidity: 55 % ATM Pressure: 101.0 kPa The testing was performed by Jason Liu on 2023-06-26. For Microwave function: Radiation leakage was measured in the as-received condition with the oven door closed using a microwave leakage meter. A 275 mL water load was placed in the center of the oven and the oven was operated at maximum output power. There was no microwave leakage exceeding a power level of 0.1mW/cm 2 observed at any point 5 cm or more from the external surface of the oven. A maximum of 1.0 mW/cm 2 is allowed in accordance with the applicable Federal Standards. Hence, microwave leakage in the as-received condition with the oven door closed was below the maximum allowed. Shenzhen Accurate Technology Co., Ltd. Report No.: RA230625-36010E-EM-01 Version 27: 2023-01-30 Page 12 of 27 FCC-EMC For BT/Wi-Fi Function: Calculated Formulary: Predication of MPE limit at a given distance S = 2 4R PG  S = power density (in appropriate units, e.g. mW/cm 2 ) P = power input to the antenna (in appropriate units, e.g., mW). G = power gain of the antenna in the direction of interest relative to an isotropic radiator, the power gain factor, is normally numeric gain. R = distance to the center of radiation of the antenna (appropriate units, e.g., cm) For worst case (PCB antenna 2) Mode Frequency (MHz) Antenna Gain Tune Up Conducted Power* Distance (cm) Power Density (mW/cm 2 ) MPE Limit (mW/cm 2 ) (dBi) (numeric)(dBm) (mW) BLE 2402-2480 4.2 2.63 0 1.00 20 0.0005 1 BDR/EDR 2402-2480 4.2 2.63 3 2.00 20 0.0010 1 Wi-Fi 2412-2462 4.2 2.63 22 158.49 20 0.0829 1 Note 1: Please refer to the certified module of FCC ID: 2AC7Z-RIGEL (Report number: RSHA180913005-00A& RSHA180913005-00B) for the tune up conducted power for the Bluetooth and Wi-Fi. Note 2: The BT function can’t transmit at the same time with the Wi-Fi function. Note 3: The BT/Wi-Fi function can transmit at the same time with Microwave function. Note 4: Simultaneous transmitting was considerate to be compliant to the limit, since low power density for BT/Wi-Fi and Microwave functions. To maintain compliance with the FCC’s RF exposure guidelines, place the equipment at least 20cm from nearby persons. Result: Compliant.

Note: This report may contain data that are not covered by the A2LA accreditation and are marked with an asterisk “★”. Shenzhen Accurate Technology Co., Ltd. is not responsible for the authenticity of any test data provided by the applicant. Data included from the applicant that may affect test results are marked with an asterisk ’*’. Customer model name, addresses, names, trademarks etc. are not considered data. This report cannot be reproduced except in full, without prior written approval of the Company. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested. This report is valid only with a valid digital signature. The digital signature may be available only under the Adobe software above version 7.0. Shenzhen Accurate Technology Co., Ltd. 1/F., Building A, Changyuan New Material Port, Science & Industry Park, Nanshan District, Shenzhen, Guangdong, P.R. China Tel: +86 755-26503290 Fax: +86 755-26503290 Web: www.atc-lab.com Version 27: 2023-01-30 Page 1 of 27 FCC-EMC TEST REPORT Applicant Name : Whirlpool Microwave Products Development Limited. Address : 17th Fl, Elite Centre,22 Hung To Rd,Kwun Tong, Hong Kong Report Number : RA230625-36010E-EM-01 FCC ID: PR4FLUSHP2MT Test Standard (s) FCC Part 18 Sample Description Product Type: Microwave Oven Model No.: MMMF8030P Trade Mark: Whirlpool Date Received: 2023- 06-25 Date of Test: 2023-06-26 Report Date: 2023- 07-06 Test Result: Pass* * In the configuration tested, the EUT complied with the standards above. Prepared and Checked By: Approved By: Zeki.Ma Candy Li EMC Engineer EMC Engineer Shenzhen Accurate Technology Co., Ltd. Report No.: RA230625-36010E-EM-01 Version 27: 2023-01-30 Page 2 of 27 FCC-EMC TABLE OF CONTENTS DOCUMENT REVISION HISTORY ......................................................................................................................... 3 GENERAL INFORMATION ....................................................................................................................................... 4 PRODUCT DESCRIPTION FOR EQUIPMENT UNDER TEST (EUT) ..................................................................................... 4 OBJECTIVE ................................................................................................................................................................... 4 TEST METHODOLOGY .................................................................................................................................................. 4 MEASUREMENT UNCERTAINTY .................................................................................................................................... 5 TEST FACILITY ............................................................................................................................................................. 5 OPERATING CONDITION/TEST CONFIGURATION .......................................................................................... 6 JUSTIFICATION ............................................................................................................................................................. 6 EUT EXERCISE SOFTWARE .......................................................................................................................................... 6 SPECIAL ACCESSORIES ................................................................................................................................................. 6 EQUIPMENT MODIFICATIONS ....................................................................................................................................... 6 SUPPORT EQUIPMENT LIST AND DETAILS .................................................................................................................... 6 EXTERNAL CABLE LIST AND DETAILS ......................................................................................................................... 6 CONFIGURATION OF TEST SETUP ................................................................................................................................. 6 BLOCK DIAGRAM OF TEST SETUP ................................................................................................................................ 7 SUMMARY OF TEST RESULT ................................................................................................................................. 8 TEST EQUIPMENT LIST ........................................................................................................................................... 9 FCC §18.313, §1.1310, §2.1091 - MAXIMUM PERMISSIBLE EXPOSURE ........................................................ 11 APPLICABLE STANDARD ............................................................................................................................................ 11 MEASUREMENT .......................................................................................................................................................... 11 CONDUCTED EMISSIONS ...................................................................................................................................... 13 APPLICABLE STANDARD ............................................................................................................................................ 13 EUT SETUP ................................................................................................................................................................ 13 EMI TEST RECEIVER SETUP ....................................................................................................................................... 13 TEST PROCEDURE ...................................................................................................................................................... 14 CALCULATION ...................................................................................................…

Text truncated - open the document above for the full version.

Shenzhen Accurate Technology Co., Ltd. Project No.: RA230625-36010E-EM-01 Test Photos Page 1 of 2 Photo of Power Line Conducted Emission Measurement Shenzhen Accurate Technology Co., Ltd. Project No.: RA230625-36010E-EM-01 Test Photos Page 2 of 2 Radiated Emissions Test View (Below 1GHz) Radiated Emissions Test View (Above 1GHz)