PR4SMARTLPKAYHousehold microwave oven

1 Table of Contents MICROWAVE OVEN SAFETY.............................................2 MICROWAVE OVEN MAINTENANCE AND CARE............4 MICROWAVE OVEN HOOD COMBINATION OWNER’S MANUAL Microwave Oven Safety ................................................2 Internet Connectivity Guide for Connected Appliances Only................................................................................3 FCC Caution..................................................................4 General Cleaning...........................................................4 INSTALLATION INSTRUCTIONS REQUIREMENTS ........5 Tools and Parts .............................................................5 Parts Supplied ..............................................................5 Location Requirements.................................................5 Product Dimensions .....................................................6 Installation Dimensions ............................................... 7 Electrical Requirements .............................................. 7 PREPARE MICROWAVE OVEN HOOD ............................ 8 INSTALLATION INSTRUCTIONS....................................... 9 Prepare Microwave Oven Hood Combination.............. 8 Installation Types........................................................... 8 Install Damper (For Wall Venting)................................... 9 Install Damper (For Roof Venting).................................. 9 Install Vent Cover (For Wall and Roof Venting).............. 10 Find the Wall Stud(s) .................................................... 11 Mark Upper Cabinet .................................................... 12 Mark Rear Wall............................................................. 13 Drill holes in Upper Cabinet......................................... 13 Drill holes in Rear Wall ................................................. 14 Attach Mounting Plate to Wall ..................................... 14 Attach Mounting Plate to Wall ..................................... 14 Install the Microwave Oven........................................... 15 Complete Installation ................................................... 16 VENTING DESIGN SPECIFICATIONS............................... 17 IMPORTANT: Save for local electrical inspector’s use. W11702685A 2 MICROWAVE OVEN SAFETY Your safety and the safety of others are very important. We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety messages. This is the safety alert symbol. This symbol alerts you to potential hazards that can kill or hurt you and others. All safety messages will follow the safety alert symbol and either the word “DANGER” or “WARNING.” These words mean: DANGER WARNING You can be killed or seriously injured if you don’t immediately follow instructions. You can be killed or seriously injured if you don’t follow instructions. All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you what can happen if the instructions are not followed. IMPORTANT SAFETY INSTRUCTIONS When using electrical appliances basic safety precautions should be followed, including the following: WARNING:                    Read all instructions before using the appliance.      !"#$%&'()*(%+('- "(**'/0##1"(*&#(#1$#**'+#2'$(3%+# ENERGY” found in this manual.      4$     4*!5(&)-')5')*&$'()*6 found in this section.  Install or locate this appliance only in accordance with the provided Installation Instructions.  Some products such as whole eggs and sealed containers 7    7  should not be heated in this oven.  &            in the manual. Do not use corrosive chemicals or vapors in   4         heat, cook, or dry food. It is not designed for industrial or laboratory use.  8($()#)*$%)$%&*#*#+##/&)*4-( )(%00(3$8'0-#)(&*#8#2'$(3%+#4&  caution when removing hot items.  Do not operate this appliance if it has a damaged cord or plug, if it is not working properly, or if it has been damaged or dropped.        9     4$     ;          4  Do not cover or block any openings on the appliance.  Do not store this appliance outdoors. Do not use this   <    wet basement, near a swimming pool, or similar locations.  Do not immerse cord or plug in water.  Keep cord away from heated surfaces.  Do not let cord hang over edge of table or counter.  Do not use replacement parts that have not been recommended by the manufacturer (e.g. parts made at home using a 3D printer).  *          !2  (2   $6  4  0 9       @   overheated beyond the boiling point without appearing to   4+           removed from the microwave oven is not always present. 8'*$(&0-#*&0')+#B8(0'C&'-**&--#)0B /('0')5(+#38#)8#$()%')#'*-'*&/#- (%&#)*'0'*')*##-')(8#0'C&'-4  Do not operate any heating or cooking appliance beneath this appliance.  Do not mount unit over or near any portion of a heating or cooking appliance.  Do not mount over a sink.  Do not store anything directly on top of the appliance surface when the appliance is in operation.  $+  8 F9 75         4          Suitable for use above both gas and electric cooking equipment.  Intended t…

Text truncated - open the document above for the full version.

CFR 47 §2.911(d)(5)(i) Attestation Letter Whirlpool Microwave Products Development Limited. Address: 17th Fl, Elite Centre,22 Hung To Rd,Kwun Tong, Hong Kong Email: [email protected] Tel: 8675583811688 Attestation Letter Date: 2024-07-11 FEDERAL COMMUNICATIONS COMMISSIONS Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 Ref: Attestation Statements CFR 47 §2.911(d)(5)(i) Filing FCC ID: PR4SMARTLPKAY Whirlpool Microwave Products Development Limited. certifies that the equipment for which authorization is sought, is not “covered” equipment prohibited from receiving an equipment authorization pursuant to section 2.903 of the FCC rules. Sincerely, Signature Bobo Lin Approbation Manager

U.S. AGENT LETTER OF ATTESTATION Date: 2024-07-11 FEDERAL COMMUNICATIONS COMMISSION Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 Ref: Attestation Statements CFR 47 §2.911(d)(7) Filing FCC ID: PR4SMARTLPKAY Whirlpool Microwave Products Development Limited. certifies that, as of the date of the filing of the application, Whirlpool Corporation is our designated U.S. agent for service of process for the above referenced FCC ID. Whirlpool Microwave Products Development Limited. accepts to maintain an agent for no less than one year after the grantee has terminated all marketing and importation or the conclusion of any Commission-related proceeding involving the equipment. Whirlpool Corporation accepts, as of the date of the filing of the application, the obligation of the designated U.S. agent for service of process for the above referenced FCC ID. Designated U.S. Agent Information: Name: Whirlpool Corporation Address: 2000 M63 North Benton Harbor, MI 49022 United States FRN: 0011042405 Tel.: 918-697-1336 Email: [email protected] Signed by (printed name): Cammie Rhodes Signature: Applicant: Whirlpool Microwave Products Development Limited. Address: 17th Fl, Elite Centre,22 Hung To Rd,Kwun Tong, Hong Kong FRN: 0012635595 Tel: 8675583811688 Email: [email protected] Signed by (printed name): Bobo Lin Signature:

CFR 47 §2.911 (d)(5)(ii) Attestation Letter Whirlpool Microwave Products Development Limited. Address: 17th Fl, Elite Centre,22 Hung To Rd,Kwun Tong, Hong Kong Email: [email protected] Tel: 8675583811688 Attestation Letter Date: 2024-07-11 FEDERAL COMMUNICATIONS COMMISSIONS Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 Ref: Attestation Statements CFR 47 §2.911(d)(5)(ii) Filing FCC ID: PR4SMARTLPKAY Whirlpool Microwave Products Development Limited. certifies that as of the date of the filing of the application, the applicant is not identified on the Covered List as an entity producing “covered” equipment. Sincerely, Signature: Name: Bobo Lin Title: Approbation Manager

Whirlpool Microwave Products Development Limited. Address: 17th Fl, Elite Centre,22 Hung To Rd,Kwun Tong, Hong Kong Email: [email protected] Tel: 8675583811688 QA-FR-170-B 7/29/2014 FCC Authorization Date: 2024-07-11 FEDERAL COMMUNICATIONS COMMISSIONS Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 Subject: Agent Authorization To whom it may concern: We, Whirlpool Microwave Products Development Limited. the undersigned, hereby authorizes Bay Area Compliance Laboratories Corp. (Shenzhen) to act on its behalf in all matters relating to application for Equipment authorization, including the signing of all documents relating to these matters. All acts carried out by Bay Area Compliance Laboratories Corp. (Shenzhen) on our behalf shall have the same effect as our own action. We, the undersigned, hereby certify that we are not subject to a denial of federal benefits, that includes FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C. 862. This authorization is valid until further written notice from the applicant. Sincerely, Signature Bobo Lin Approbation Manager

Whirlpool Microwave Products Development Limited. Address: 17th Fl, Elite Centre,22 Hung To Rd,Kwun Tong, Hong Kong Email: [email protected] Tel: 8675583811688 FCC Confidential Authorization Date: 2024-07-11 FEDERAL COMMUNICATIONS COMMISSIONS Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 Subject: Confidentiality Request regarding application for certification of FCC ID: PR4SMARTLPKAY In accordance with Sections 0.457 and 0.459 of the Commission’s Rules, Whirlpool Microwave Products Development Limited. hereby requests long-term confidential treatment of information accompanying this application as outlined below:  Block Diagram  Schematics  Operation Description The above materials contain proprietary and confidential information not customarily released to the public. The public disclosure of these materials provides unjustified benefits to its competitors in the market. Sincerely, Signature Bobo Lin Approbation Manager

Bay Area Compliance Laboratories Corp. (Shenzhen) Project No.: 2401S71984E-EM Page 1 of 4 EXHIBIT B - EUT EXTERNAL PHOTOGRAPHS Bay Area Compliance Laboratories Corp. (Shenzhen) Project No.: 2401S71984E-EM Page 2 of 4 Bay Area Compliance Laboratories Corp. (Shenzhen) Project No.: 2401S71984E-EM Page 3 of 4 Bay Area Compliance Laboratories Corp. (Shenzhen) Project No.: 2401S71984E-EM Page 4 of 4

Bay Area Compliance Laboratories Corp. (Shenzhen) Project No.: 2401S71984E-EM EXHIBIT A - FCC ID LABEL AND LOCATION FCC ID Label FCC ID Label Location Information The label shown shall be permanently affixed at a conspicuous location on the device and be readily visible to the user at the time purchase (Labeling requirements per 2.925)

Bay Area Compliance Laboratories Corp. (Shenzhen) Project No.: 2401S71984E-EM Page 1 of 16 EXHIBIT C - EUT INTERNAL PHOTOGRAPHS Bay Area Compliance Laboratories Corp. (Shenzhen) Project No.: 2401S71984E-EM Page 2 of 16 Bay Area Compliance Laboratories Corp. (Shenzhen) Project No.: 2401S71984E-EM Page 3 of 16 Bay Area Compliance Laboratories Corp. (Shenzhen) Project No.: 2401S71984E-EM Page 4 of 16 Bay Area Compliance Laboratories Corp. (Shenzhen) Project No.: 2401S71984E-EM Page 5 of 16 Bay Area Compliance Laboratories Corp. (Shenzhen) Project No.: 2401S71984E-EM Page 6 of 16 Bay Area Compliance Laboratories Corp. (Shenzhen) Project No.: 2401S71984E-EM Page 7 of 16 Bay Area Compliance Laboratories Corp. (Shenzhen) Project No.: 2401S71984E-EM Page 8 of 16 Bay Area Compliance Laboratories Corp. (Shenzhen) Project No.: 2401S71984E-EM Page 9 of 16 Bay Area Compliance Laboratories Corp. (Shenzhen) Project No.: 2401S71984E-EM Page 10 of 16 Bay Area Compliance Laboratories Corp. (Shenzhen) Project No.: 2401S71984E-EM Page 11 of 16 Bay Area Compliance Laboratories Corp. (Shenzhen) Project No.: 2401S71984E-EM Page 12 of 16 Bay Area Compliance Laboratories Corp. (Shenzhen) Project No.: 2401S71984E-EM Page 13 of 16 Bay Area Compliance Laboratories Corp. (Shenzhen) Project No.: 2401S71984E-EM Page 14 of 16 Bay Area Compliance Laboratories Corp. (Shenzhen) Project No.: 2401S71984E-EM Page 15 of 16 Bay Area Compliance Laboratories Corp. (Shenzhen) Project No.: 2401S71984E-EM Page 16 of 16

Bay Area Compliance Laboratories Corp. (Shenzhen) Report No.: 2401S71984E-EM-00 TR-EM-RF027 Page 10 of 33 Version 1.0 (2023/10/07) FCC §18.313, §1.1310, §2.1091- MAXIMUM PERMISSIBLE EXPOSURE Applicable Standard According to subpart §1.1310, systems operating under the provisions of this section shall be operated in a manner that ensures that the public is not exposed to radio frequency energy level in excess of the Commission’s guidelines. Limits for Maximum Permissible Exposure (MPE) (§1.1310, §2.1091) (B) Limits for General Population/Uncontrolled Exposure Frequency Range (MHz) Electric Field Strength (V/m) Magnetic Field Strength (A/m) Power Density (mW/cm 2 ) Averaging Time (minutes) 0.3–1.34 614 1.63 *(100) 30 1.34–30 824/f 2.19/f *(180/f²) 30 30–300 27.5 0.073 0.2 30 300–1500 / / f/1500 30 1500–100,000 / / 1.0 30 f = frequency in MHz; * = Plane-wave equivalent power density; Measurement Environmental Conditions Temperature: 26 °C Relative Humidity: 54 % ATM Pressure: 101 kPa The testing was performed by Joson Xiao on 2024-05-14. Radiation leakage was measured in the as-received condition with the oven door closed using a microwave leakage meter. A 275 mL water load was placed in the center of the oven and the oven was operated at maximum output power, at the same time, the Wi-Fi is turned on to measure the simultaneous radiation of Wi-Fi and microwave. There was no microwave leakage plus Wi-Fi radiation exceeding a power level of 0.1mW/cm 2 observed at any point 5 cm or more from the external surface of the oven. A maximum of 1.0 mW/cm 2 is allowed in accordance with the applicable Federal Standards. Hence, microwave leakage and Wi-Fi radiation in the as-received condition with the oven door closed was below the maximum allowed.

Note: The information marked # is provided by the applicant, the laboratory is not responsible for its authenticity and this information can affect the validity of the result in the test report. Customer model name, addresses, names, trademarks etc. are included. This report cannot be reproduced except in full, without prior written approval of the Company. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested. This report is valid only with a valid digital signature. The digital signature may be available only under the Adobe software above version 7.0. This report must not be used by the customer to claim product certification, approval, or endorsement by NVLAP or any agency of the U.S. Government. This report may contain data that are not covered by the NVLAP accreditation and are marked with an asterisk “▼”. Bay Area Compliance Laboratories Corp. (Shenzhen) 5F(B-West) , 6F, 7F, the 3rd Phase of Wan Li Industrial Building D, Shihua Rd, FuTian Free Trade Zone, Shenzhen, China Tel: +86-755-33320018 Fax: +86-755-33320008 www.baclcorp.com.cn TR-EM-RF027 Page 1 of 33 Version 1.0 (2023/10/07) TEST REPORT Applicant Name: Whirlpool Microwave Products Development Limited. Address: 17th Fl, Elite Centre, 22 Hung To Rd, Kwun Tong, Hong Kong Report Number: 2401S71984E-EM-00 FCC ID: PR4SMARTLPKAY Test Standard (s) FCC PART 18 Sample Description Product Type: Household microwave oven Model No.: YWMML5530R Multiple Model(s) No.: N/A Trade Mark: Whirlpool Date Received: 2024/04/22 Issue Date: 2024/07/23 Test Result: Pass ▲ ▲ In the configuration tested, the EUT complied with the standards above. Prepared and Checked By: Approved By: Joson Xiao Moon Liu EMC Engineer EMC Supervisor Bay Area Compliance Laboratories Corp. (Shenzhen) Report No.: 2401S71984E-EM-00 TR-EM-RF027 Page 2 of 33 Version 1.0 (2023/10/07) TABLE OF CONTENTS DOCUMENT REVISION HISTORY ......................................................................................................................... 3 GENERAL INFORMATION ....................................................................................................................................... 4 PRODUCT DESCRIPTION FOR EQUIPMENT UNDER TEST (EUT) ..................................................................................... 4 OBJECTIVE ................................................................................................................................................................... 4 MEASUREMENT UNCERTAINTY .................................................................................................................................... 4 TEST FACILITY ............................................................................................................................................................. 5 OPERATING CONDITION/TEST CONFIGURATION .......................................................................................... 6 DESCRIPTION OF TEST CONFIGURATION ...................................................................................................................... 6 EUT EXERCISE SOFTWARE .......................................................................................................................................... 6 SPECIAL ACCESSORIES ................................................................................................................................................. 6 EQUIPMENT MODIFICATIONS ....................................................................................................................................... 6 SUPPORT EQUIPMENT LIST AND DETAILS .................................................................................................................... 6 EXTERNAL CABLE LIST AND DETAILS ......................................................................................................................... 6 CONFIGURATION OF TEST SETUP ................................................................................................................................. 6 BLOCK DIAGRAM OF TEST SETUP ................................................................................................................................ 7 SUMMARY OF TEST RESULT ................................................................................................................................. 8 TEST EQUIPMENT LIST ........................................................................................................................................... 9 FCC §18.313, §1.1310, §2.1091- MAXIMUM PERMISSIBLE EXPOSURE ......................................................... 10 APPLICABLE STANDARD ............................................................................................................................................ 10 MEASUREMENT .......................................................................................................................................................... 10 CONDUCTED EMISSIONS ...................................................................................................................................... 11 APPLICABLE STANDARD ............................................................................................................................................ 11 EUT SETUP ................................................................................................................................................................ 11 EMI TEST RECEIVER SETUP ....................................................................................................................................... 11 TEST PROCEDURE ...................................................................................................................................................... 12 TEST DATA ..........................................................................................................................................…

Text truncated - open the document above for the full version.

Note: The information marked # is provided by the applicant, the laboratory is not responsible for its authenticity and this information can affect the validity of the result in the test report. Customer model name, addresses, names, trademarks etc. are included. This report cannot be reproduced except in full, without prior written approval of the Company. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested. This report is valid only with a valid digital signature. The digital signature may be available only under the Adobe software above version 7.0. This report must not be used by the customer to claim product certification, approval, or endorsement by NVLAP or any agency of the U.S. Government. This report may contain data that are not covered by the NVLAP accreditation and are marked with an asterisk “▼”. Bay Area Compliance Laboratories Corp. (Shenzhen) 5F(B-West) , 6F, 7F, the 3rd Phase of Wan Li Industrial Building D, Shihua Rd, FuTian Free Trade Zone, Shenzhen, China Tel: +86-755-33320018 Fax: +86-755-33320008 www.baclcorp.com.cn TR-EM-RF027 Page 1 of 33 Version 1.0 (2023/10/07) TEST REPORT Applicant Name: Whirlpool Microwave Products Development Limited. Address: 17th Fl, Elite Centre, 22 Hung To Rd, Kwun Tong, Hong Kong Report Number: 2401S71984E-EM-00 FCC ID: PR4SMARTLPKAY Test Standard (s) FCC PART 18 Sample Description Product Type: Household microwave oven Model No.: YWMML5530R Multiple Model(s) No.: N/A Trade Mark: Whirlpool Date Received: 2024/04/22 Issue Date: 2024/07/23 Test Result: Pass ▲ ▲ In the configuration tested, the EUT complied with the standards above. Prepared and Checked By: Approved By: Joson Xiao Moon Liu EMC Engineer EMC Supervisor Bay Area Compliance Laboratories Corp. (Shenzhen) Report No.: 2401S71984E-EM-00 TR-EM-RF027 Page 2 of 33 Version 1.0 (2023/10/07) TABLE OF CONTENTS DOCUMENT REVISION HISTORY ......................................................................................................................... 3 GENERAL INFORMATION ....................................................................................................................................... 4 PRODUCT DESCRIPTION FOR EQUIPMENT UNDER TEST (EUT) ..................................................................................... 4 OBJECTIVE ................................................................................................................................................................... 4 MEASUREMENT UNCERTAINTY .................................................................................................................................... 4 TEST FACILITY ............................................................................................................................................................. 5 OPERATING CONDITION/TEST CONFIGURATION .......................................................................................... 6 DESCRIPTION OF TEST CONFIGURATION ...................................................................................................................... 6 EUT EXERCISE SOFTWARE .......................................................................................................................................... 6 SPECIAL ACCESSORIES ................................................................................................................................................. 6 EQUIPMENT MODIFICATIONS ....................................................................................................................................... 6 SUPPORT EQUIPMENT LIST AND DETAILS .................................................................................................................... 6 EXTERNAL CABLE LIST AND DETAILS ......................................................................................................................... 6 CONFIGURATION OF TEST SETUP ................................................................................................................................. 6 BLOCK DIAGRAM OF TEST SETUP ................................................................................................................................ 7 SUMMARY OF TEST RESULT ................................................................................................................................. 8 TEST EQUIPMENT LIST ........................................................................................................................................... 9 FCC §18.313, §1.1310, §2.1091- MAXIMUM PERMISSIBLE EXPOSURE ......................................................... 10 APPLICABLE STANDARD ............................................................................................................................................ 10 MEASUREMENT .......................................................................................................................................................... 10 CONDUCTED EMISSIONS ...................................................................................................................................... 11 APPLICABLE STANDARD ............................................................................................................................................ 11 EUT SETUP ................................................................................................................................................................ 11 EMI TEST RECEIVER SETUP ....................................................................................................................................... 11 TEST PROCEDURE ...................................................................................................................................................... 12 TEST DATA ..........................................................................................................................................…

Text truncated - open the document above for the full version.

Bay Area Compliance Laboratories Corp. (Shenzhen) Report No.: 2401S71984E-EM Page 1 of 3 EXHIBIT D - TEST SETUP PHOTOGRAPHS Conducted Emissions - Front View Conducted Emissions - Side View Bay Area Compliance Laboratories Corp. (Shenzhen) Report No.: 2401S71984E-EM Page 2 of 3 Radiated Emissions View (Below 1 GHz) Radiated Emissions View (1-18 GHz) Bay Area Compliance Laboratories Corp. (Shenzhen) Report No.: 2401S71984E-EM Page 3 of 3 Radiated Emissions View (18-25 GHz)