PSX-I11-SERIESMini Wireless Router

Mini 3G Router i11 Quick Start Guide Package Contents:  One i11 Mini 3G Router  One USB data Cable  One Power Adapter  One installation Guide If any of above items are damaged or missing, please contact with your distributor. Panel Layout Name Fuction System LED Red The Router is power on Red in quickly flashing transmission data via WiFi Green LAN/WAN cable is connected but there is no data being transmitted or received Green in quickly flashing LAN/WAN cable is connected but there is data being transmitted or received Link Status LED Blue in slowly flashing 3G or WAN is not connected Bule in quickly flashing 3G or WAN is connected 3G Port The port is used to connect 3G modem. 3G/DHCP Switch This switch is used to switch operation mode of the Router between 3G and DHCP. Power This port is used to connect the provided power adapter. LAN/WAN This LAN/WAN port works as WAN in Dynamic IP/Static IP/PPPoE mode and as LAN in 3G mode. As LAN, it connects the Router to the local PC; as WAN, it enables you connect DSL/cable Modem, or Ethernet. RESET With the Router powered on, use a pin to press and hold the RESET button (about 8 seconds) until the LED becomes turn off, and then release the button and wait the Router reboot to its default settings. Quick install i11 Hardware installation 1. powered by USB cable connect the Router and the computer using a USB cable like below, the Router can powerd on automatically. 2. Powered by USB adapter You also can use USB adapter to supply for the Rouer, follow step 1, 2, 3 to connect them. Notes：The output of the adapter should between 5V 750mAh and 5V, 2A. Connecting the Router Plug the power plug in the electrical wall socket. The Router will start to work automatically. [Windows XP] Click the "Start/Control Panel", double-click "Network Connections", in the "Wireless Network Connection" right click and select "View Available Wireless Networks", Highlight the SSID of Router (here is 3G ROUTER) and cick “Connect” to add to the network. On the right shows "connected” that indicates successfully connected to the 3G router. [Winodws 7] When 3G modem installed, the lower right corner of the computer there is a icon, click the icon, and will see a pop-up network list, select "3G ROUTER" the wireless network, and then double-click it to connect, when the screen appears "connected". Now let’s open the IE Explorer( Iphone for Safari),type the default IP:192.168.100.1 in the Address bar, then the Username：admin, Password: admin，No bold words，click OK into the management interface: Setting 3G Router the router support 3G, Static IP, Dynamic IP, PPPoE, click “Basic Settings” on the left side of WEB page, so you should first choose Router’s operating mode, the default mode is “3G dialup”. 1. 3G Dial-UP The default mode for the Router is 3G Dial-up. It already integrates many ISP parameters over the world, and customers can choose the ones they want accroding to 3G Modems, there is different parameters in different country. For the foreigners, if a 3G Modem is not compatible with our Router, we can realize it from remote online control, to make your 3G modems comply our router. Return to “Status > Running Status”, check “3G Dialup” says “connected”, if it’s connected, you should be able to access Internet via 3G. Other cases: If 3G Dialup says “disconnect”, it means no 3G connection, maybe your 3G Modem is not attached to the router, you can check the Modem’s VID/PID in 3G Modem(VID/PID), if the VID/PID is Unrecognized, either the router’s USB port is bad or the 3G Modem is bad. If “3G Dialup” says “connecting, please wait...”, it means that the router is dialing now, please wait for a moment, after 20 seconds, refresh the page until “3G Dialup” says “connected”, if the status “connecting, please wait...” has shown for a long time, please check as follows: 1. Check the 3G Router has supported your 3G Modem; 2. Check your 3G Modem can work well when directly connected to your computer. 3. Check your settings are correct. 2. PPPoE If you have applied ADSL to realize Dial-up service, you should choose this type. Under this condition, you should fill in both the User Name and Password that the ISP supplied. Please note that there fields are case-sensitive. Open the router WEB interface, click on the "Basic Settings> Internet access mode", select PPPoE, enter the broadband Internet account and password, click "OK" to save the settings, Return to the "System Status> running", if PPPoE dial-up display "Connected", said that it has successfully connected to the broadband network. 3. Staic IP Network operators to provide you with an Internet IP address, select Static IP, static IP mode, the router's WAN port to use as an ETH port. In the "Basic Settings> Internet access mode" select the Static IP mode, then enter your ISP's IP address, subnet mask, default gateway, DNS and other related parameters can be. 4. Dynamic IP Dynamic IP is widely used in hotels and restaurants and other public places, the Router can connect via dynamic IP mode to hotels and other public access network resources, the first, hotel of the network cable to the ETH interface to the router, then through the following two methods to router switch to dynamic IP mode. 1) hard-switching: the switch router 3G/DHCP pull to the DHCP file. 2) Soft Switch: turn on the router interface, click on the "Basic Settings> Internet access mode", select the dynamic IP, and then click "OK" to save the settings. Wireless Encryption Selecting “Wireless Settings>Wireless Encription”, will enable you to configure wireless security for your wireless network to protect your data from intruders. The Router prodivers three types: WEP, WPA-PSK, WPA2-PSK. The security options are different operation mode, it is recommended to use WPA-PSK security mode.

Page 67 of 70 FCC ID: PSX-I11-SERIES Anbotek Compliance Laboratory Limited Report No. 201208837F AppendixI(External Photos) Figure 1 The EUT-Overall View Figure 2 The EUT-Back View Page 68 of 70 FCC ID: PSX-I11-SERIES Anbotek Compliance Laboratory Limited Report No. 201208837F Figure 3 The EUT-Side View Figure 4 The EUT-Side View

FCC ID Label Sample for FCC ID: PSX-I11-SERIES FCC ID: PSX-I11-SERIES This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: 1. This device may not cause harmful interference, and 2. This device must accept any interference received, including interference that may cause undesired operation.

The proposed Label Location on EUT Proposed FCC Label Location Proposed Label Location on EUT The EUT-View/Proposed FCC Label Location

Page 69 of 70 FCC ID: PSX-I11-SERIES Anbotek Compliance Laboratory Limited Report No. 201208837F Appendix II (Internal Photos) Figure 5 The EUT-Inside View Figure 6 PCB of the EUT-Front View Page 70 of 70 FCC ID: PSX-I11-SERIES Anbotek Compliance Laboratory Limited Report No. 201208837F Figure 7 PCB of the EUT-Back View

FCC ID:PSX-I11-SERIES Page 1 o f 19 Anbotek Compliance Laboratory Limited Report No. 201208837F-1 DECLARATION OF CONFORMITY On Behalf of Futurepath Technology (Shenzhen) CO.,LTD. Mini Wireless Router Model No.: i11 series Prepared for : Futurepath Technology (Shenzhen) CO.,LTD. Address : Unit01,13/F HuaRong Building,No.178 MinTian Road,FuTian District Shenzhen,China Prepared By : Anbotek Compliance Laboratory Limited Address : 1/F, 1 /Building, SEC Industrial Park, No. 4 Qianhai Road, Nanshan District, Shenzhen, 518054, China Tel: (86) 755-26066544 Fax: (86) 755-26014772 Report Number : 201208837F-1 Date of Test : Aug.30, 2012 to Sept.14, 2012 Date of Report : Sept.14, 2012 FCC ID:PSX-I11-SERIES Page 2 o f 19 Anbotek Compliance Laboratory Limited Report No. 201208837F-1 TABLE OF CONTENTS Description Page Test Report Verification 1. GENERAL INFORMATION ............................................................................................................... 4 1.1. Description of Device (EUT) ..........................................................................................................................4 2. POWER LINE CONDUCTED MEASUREMENT ........................................................................... 5 2.1. Test Equipment ...............................................................................................................................................5 2.2. Block Diagram of Test Setup ..........................................................................................................................5 2.3. Power Line Conducted Emission Measurement Limits (FCC Part 15 Class B) .............................................5 2.4. Configuration of EUT on Measurement..........................................................................................................6 2.5. Operating Condition of EUT...........................................................................................................................6 2.6. Test Procedure.................................................................................................................................................6 2.7. Power Line Conducted Emission Measurement Results.................................................................................6 3. RADIATED EMISSION MEASUREMENT...................................................................................... 9 3.1. Test Equipment ...............................................................................................................................................9 3.2. Block Diagram of Test Setup ..........................................................................................................................9 3.3. Radiated Emission Limit (Subpart B Class B) ..............................................................................................10 3.4. EUT Configuration on Measurement ............................................................................................................10 3.5. Operating Condition of EUT.........................................................................................................................10 3.6. Test Procedure...............................................................................................................................................10 3.7. Radiated Emission Measurement Results .....................................................................................................11 4. PHOTOGRAPH .................................................................................................................................. 14 4.1. Photo of Power Line Conducted Emission Test............................................................................................14 4.2. Photo of Radiated Emission Test ..................................................................................................................15 AppendixI(External Photos)(2pages) Appendix II (Internal Photos)(2pages) FCC ID:PSX-I11-SERIES Page 3 o f 19 Anbotek Compliance Laboratory Limited Report No. 201208837F-1 TEST REPORT VERIFICATION Applicant : Futurepath Technology (Shenzhen) CO.,LTD. Manufacturer : Futurepath Technology (Shenzhen) CO.,LTD. EUT : Mini Wireless Router Model No. : i11 series Rating : DC 5V/1A Trade Mark : Bizkey Measurement Procedure Used: FCC Rules and Regulations Part 15 Subpart B 2011 & FCC / ANSI C63.4-2009 The device described above is tested by Anbotek Compliance Laboratory Limited To determine the maximum emission levels emanating from the device. The maximum emission levels are compared to the FCC Part 15 Subpart B Class B limits both radiated and conducted emissions. The measurement results are contained in this test report and Anbotek Compliance Laboratory Limited Is assumed full responsibility for the accuracy and completeness of these measurements. Also, this report shows that the Equipment Under Test (EUT) is to be technically compliant with the FCC requirements. This report applies to above tested sample only. This report shall not be reproduced in part without written approval of Anbotek Compliance Laboratory Limited Date of Test : Aug.30, 2012 to Sept.14, 2012 Prepared by : (Engineer/ Barak Ban) Reviewer : (Project Manager/ Jerry Du) Approved & Authorized Signer : (Manager/ Tom Chen) FCC ID:PSX-I11-SERIES Page 4 o f 19 Anbotek Compliance Laboratory Limited Report No. 201208837F-1 1. GENERAL INFORMATION 1.1. Description of Device (EUT) Description : Mini Wireless Router Model Number : i11 series Test Power Supply : DC 5V Applicant : Futurepath Technology (Shenzhen) CO.,LTD. Address : Unit01,13/F HuaRong Building,No.178 MinTian Road,FuTian District Shenzhen,China Manufacturer : Futurepath Technology (Shenzhen) CO.,LTD. Address : Unit01,13/F HuaRong Building,No.178 MinTian Road,FuTian District Shenzhen,China Date of Sample received : Aug. 30, 2012 Date of Test : Aug.30, 2012 to Sept.14, 2012 FCC ID:PSX-I11-SERIES Page 5 o…

Text truncated - open the document above for the full version.

Page 65 of 70 FCC ID: PSX-I11-SERIES Anbotek Compliance Laboratory Limited Report No. 201208837F 6. PHOTOGRAPH 6.1. Photo of Conducted Emission Measurement Page 66 of 70 FCC ID: PSX-I11-SERIES Anbotek Compliance Laboratory Limited Report No. 201208837F 6.2. Photo of Radiation Emission Test Below 1G Above 1G