PTD-EA-1121660RFID Security Information System

LT-LFS01-LM Operator’s Manual UM-1146630, rev. A Page 1 LT-LFS01-LM LogiRead LF reader for Lumenis Operator’s Manual LT-LFS01-LM Operator’s Manual UM-1146630, rev. A Page 2 This manual is copyrighted with all rights reserved. Under copyright laws, this manual may not be copied in whole or in part or reproduced in any other media without the express written permission of the Lumenis group of companies. Permitted copies must carry the same proprietary and copyright notices as were affixed to the original. Under the law, copying includes translation into another language. Please note that while every effort has been made to ensure that the information in this document is accurate, the instructions, photos, figures, illustrations, tables, specifications, and schematics contained herein are subject to change without notice. Lumenis and the Lumenis Logo are trademarks of the Lumenis group of companies. Lumenis Ltd. P.O.B. 240 Yokneam 20692 Israel Copyright © 2012, Lumenis Ltd. November 2012 UM-1146630, Revision A LT-LFS01-LM Operator’s Manual UM-1146630, rev. A Page 3 1. Introduction The LogiRead LF one channel reader LT-LFS01-LM is an RFID integrator modified for Lumenis applications. The LogiRead is available as a stand-alone product, ready to be embedded in every machine designed, produced or marketed by Lumenis. The compact reader provides a complete and low cost read & write module, supporting all HiTag transponders, including HiTag-S types, which feature an anti-collision protocol for simultaneous reading of multiple tags. The purpose of the LT-LFS01-LM module is mainly, but not limited to, the management of consumables attached to Lumenis systems. It features up to 15cm reading distance, supports anti-collision protocol and includes data encryption options. LT-LFS01-LM Operator’s Manual UM-1146630, rev. A Page 4 2. Specifications 2.1 RFID Specifications  Operating Frequency: 125 kHz  Supported Transponders: HITAG 1+2 & HITAG S  Anti-collision support 2.2 Environmental Conditions  Operating Temperature: -20°C to +65°C  Storage Temperature: -40°C to +85°C 2.3 Physical Specifications  Length: 8cm / 3.14 Inches  Width: 6cm/ 2.36 Inches 2.4 Power Specifications  Supply Voltage: 10-24V  Power Consumption: 0.6W (@ 12V) 2.5 Interfaces  Communication: RS-232 LT-LFS01-LM Operator’s Manual UM-1146630, rev. A Page 5 3. Installation This module is to be initially installed and tested only by an authorized Lumenis technician. The LT-LFS01-LM contains 3 connectors to be used within Lumenis systems (refer to Figure 1):  J1 – Power.  J2 – RS232 communication.  J3 – Antenna. Figure 1 - LogiRead LT-LFS01-LM and an open representative metal housing After connecting all cables internally in Lumenis system, make sure they are tightly connected or screwed as necessary. Do not turn on the system before all connections are secured. J3 J1 J2 LT-LFS01-LM Operator’s Manual UM-1146630, rev. A Page 6 4. Safety and Regulatory The LT-LFS01-LM equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules (its FCC ID is designated as PTD-EA-1121660). These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:  Reorient or relocate the receiving antenna.  Increase the separation between the equipment and receiver.  Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.  Consult the dealer or an experienced radio/TV technician for help. Lumenis is not responsible for any radio or communication interference caused by using other than specified or recommended cables and or by unauthorized changes or modifications to this equipment. Unauthorized changes or modification could void the user’s authority to operate the equipment. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: 1. This device may not cause harmful interference, and 2. This device must accept any interference received, including interference that may cause undesired operation. This module also complies with the regulatory standard of ETSI EN 300 330-1 and ETSI EN 300 330-2, subjected to the SII test report No. 9212324456 regarding the LM- LFS01-LM electromagnetic compatibility and radio spectrum matters (ERM) for short LT-LFS01-LM Operator’s Manual UM-1146630, rev. A Page 7 range devices (SRD). Specifically, the operating frequencies, transmitter carrier output levels, radiated spurious emissions, etc. were found compatible to the standards are the module is permitted for use for within Lumenis systems and their intended use.

CONFIDENTIALITY FORM LUMENIS LTD. Federal Communications Commission 7435 Oakland Mills Road Columbia, MD 21046 Gentlemen: This letter is to comply with Sections 0.457 and 0.459 pertaining to confidential material. Lumenis LTD. would like the following documents regarding this submission for FCC ID: PTD-EA-1121660 1. SIS block diagram 2. Schematics. (ED-1121660_A RFID BOARD FOR AP WG) 3. Parts List. 4. Operation description. The above material contains trade secrets or technical data, which would customarily be guarded from competitors. We do not want these documents to be accessible to the general public. Sincerely, Eyal Benisty Eyal BenistyEyal Benisty Eyal Benisty R&D, Electronics Manager Lumenis LTD.

MODULAR APPROVAL LETTER FCC ID: PTD-EA-1121660 Item Requirements EUT 1 The modular transmitter must have its own RF shielding The modular transmitter has its own RF shielding. 2 The modular transmitter must have buffered modulation/data inputs. The modular transmitter has RS232 connection. 3 The modular transmitter must have its own power supply regulation. The modular transmitter has its own power supply regulation. 4 The modular transmitter must comply with the antenna and transmission system requirements of sections 15.203, 15.204(b) and 15.204(c) The Standard connector is available. Applied for Modular Approval. A professional installation statement has being provided in User Manual. 5 The modular transmitter must be tested in a stand-alone configuration, i.e., the module must not be inside another device during testing. This is intended to demonstrate that the module is capable of complying with Part 15 emission limits regardless of the device into which it is eventually installed. The modular transmitter has been tested in a stand-alone configuration. 6 The modular transmitter must be labeled with its own FCC ID number, and, if the FCC ID is not visible when the module is installed inside another device, then the outside of the device into which the module is installed must also display a label referring to the enclosed module. This exterior label can use wording such as the following: "Contains Transmitter Module FCC ID: XYZMODEL1" or "Contains FCC ID: XYZMODEL1." Any similar wording that expresses the same meaning may be used. The Grantee may either provide such a label, an example of which must be included in the application for equipment authorization, or, must provide adequate instructions along with the module which explain this requirement. In the latter case, a copy of these instructions must be included in the application for equipment authorization The modular transmitter has been labeled with its own FCC ID number. The exterior label of Acupulse machine includes the phrase: "contains transmitter module, FCC ID: PTD-EA-1121660” 7 The modular transmitter must comply with any specific rule or operating requirements applicable to the transmitter and the manufacturer must provide adequate instructions along with the module to explain any such requirements. Refer to test report # 9212324457 Device complies to §15.209 and 15.207 8 The modular transmitter must comply with any applicable RF exposure requirements. Complies. Eyal Benisty R&D, Electronics Manager Lumenis ltd.

October 31, 2012 Statement The LogiRead LF one channel reader LT-LFS01-LM (FCC ID: PTD-EA-1121660) is an RFID integrator modified for Lumenis applications. The purpose of this module is mainly, but not limited to, the management of consumables attached to Lumenis systems. It has no use for the general public for any other application, and cannot be used as such, as it contains authentication keys known only to Lumenis. The RFID FCC ID: PTD-EA-1121660 module installation must be carried out by trained and authorized personnel. The module is intended to be employed within Lumenis' machines. Hence such an installation requires opening the laser console, which may be done by licensed professionals to begin with. Furthermore, the matching between the module and the system may vary from one machine to another and may require dedicated tools. The RFID module shall not be sold to the general public whatsoever. It must be sold to authorized distributers or service personnel as a spare part. Each sale and each installation is controlled and documented. After installation, the installer must verify the validity of installation, which may require specific knowledge, such as a service password to the machine or some service accessory, which is not a saleable item, but distributed to licensed professionals only. Sincerely, Eyal Benisty R&D, Electronics Manager Lumenis LTD.

External photos

YES NO 120 45 134 74.5 81.3 6 5 8 2 1 3 9 B 4 5 7 3 NOTES, UNLESS OTHERWISE SPECIFIED: INDIVIDUALLY BAG AND TAG WITH LUMENIS P/N AND REVISION.1. PART TO BE CLEAN, FREE AND CLEAR OF METAL CHIPS, MACHINING OILS AND ANY FOREIGN MATERIALS.2. REV. mm DRAWING No: CATALOG No: LINEAR CHAMFERS ANGULAR OTHERWISE SPECIFIED : TOLERANCES UNLESS NAME DWG SIZE A3 QUALITY SURFACE SCALE SHEET DO NOT MEASURE ON DRAWING BORES MATERIAL: FINISH: DIMENSION IN: PART NAME: DRAWN Tel: 972-4-959-9000 FAX: 972-4-959-9070 APPROVED CHECKED DESIGNED D C B AA 1 2 B 3 4 5 C D 12 DESCRIPTION 3 APPROVED 4 DATE REV. 5 DATE 1:2 1 1 OF AP WG SIS Reader Assy N.A N.A AD-1121450 SA-1121450 B ECO No. ZONE DRAWN Eyal B. SHAUL L. A RELEASE NEW DRAWING NISSIM B.A Yuval E. CAD: Solid Works SIGN 28.03.12 SUR 3109 Ella S. 28.03.12 1.6 0.2 30' 0.3X45 ° +0.1 28.03.12 28.03.12 28.03.12 Ella S. Ella S. ADD ITEM 17 SUR3330B 18.11.12N.G.

REV. ECO No. ZONE DESCRIPTION DRAWN APPROVED DATE A SUR3330 RELEASE NEW DRAWING N.G. N.B.A. 18.11.12 * LABEL BOX IS FOR BOUNDING ONLY NAME SIGN DATE TOLERANCES UNLESS OTHERWISE SPECIFIED MATERIAL LB-002787 DESIGNED R&D 18.11.12 DRAWN Neta G. 18.11.12 LINEAR NA FINISH NA CHECKED Yuval E. 18.11.12 ANGULAR NA APPROVED Dorit R. 18.11.12 CHAMFERS NA PART NAME FCC ID Printed Label √ RoSH YES NO Copyright by All rights reserved. This drawing contains confidential & proprietary information which the authorized recipient agrees to protect & not to disclose. SURFACE Q. NA SCALE DWG SIZE -/- A4 TEL: 972-4-9599-9000 FAX: 972-4-959-9050 DO NOT MEASURE ON DRAWING Dimension DRAWING No. MD-1146450 REV. A SHEET 1 OF 1 mm CATALOG No. LB-1146450 NOTE: 1. BAG AND TAG WITH LUMENIS P/N AND REVISION. 2. LABEL MATERIAL: POLYESTER, SELF ADHESIVE BACK. 3. LABEL SIZE: 45 x 20 mm. 3. BACKGRAUND COLOR - SILVER. 4. TEXT & GRAPHICS COLOR - BLACK

RFID board PS & CS RFID Board with Bracket – front side RFID Board with Bracket and Cover – rear side RFID board with Bracket and Cover within the AcuPulse machine Antenna embedded in blue port cover

Test Report No.: 9212324457 Page 1 of 20 pages Title: RFID Security Information System Model: LogiRead LF One Channel Test Report No. 9212324457 Applicant: Lumenis Ltd. Equipment Under Test: RFID Security Information System Model: LogiRead LF One Channel FCC ID: PTD-EA-1121660 From The Standards Institution Of Israel Industry Division Electronics & Telematics Laboratory EMC Section ACLASS Accreditation Services Certificate Number: AT-1359 Test Report No.: 9212324457 Page 2 of 20 pages Title: RFID Security Information System Model: LogiRead LF One Channel Applicant: Lumenis Ltd. Address: Yokneam Industrial Park, P.O.B 240, Israel Sample for test selected by: The customer The date of test: 16, 23 August 2012 Description of Equipment Under Test (EUT): RFID Security Information System Model: LogiRead LF One Channel Serial number: LT-LFS-LM Manufactured by: Logitag Ltd Reference Documents: ™ CFR 47 FCC: Rules and Regulations; Part 15. “Radio frequency devices”; Subpart B: “Unintentional radiators” (2009). Section 15.109. Radiated emission limits. Subpart C : “Intentional radiators” (2009), Section 15.207. Conducted limits Section 15.209. “Radiated emission limits, general requirements”. This Test Report contains 19 pages and may be used only in full. This Test Report applies only to the specimen tested and may not be applied to other specimens of the same product. Test Report No.: 9212324457 Page 3 of 20 pages Title: RFID Security Information System Model: LogiRead LF One Channel 1. Test summary Parameter FCC Part 15 Reference paragraph Verdict Radiated emission test. Subpart C Section 15.209. Comply Radiated emission test. Subpart B Section 15.109 class A Comply Conducted emissions test Subpart C Section 15.207 Comply Telematics Laboratory August 2012 Name: Eng. Yuri Rozenberg Name: Michael Feldman Position: Head of EMC Branch Position: Test Technician Measurement uncertainty. Were relevant, the following measurement uncertainty level have been estimated for tests performed on the EUT as specified in CISPR 16-4-2: This uncertainty represents an expended uncertainty expressed at approximately the 95% confidence level using a coverage factor of k=2. Test description Expanded uncertainty Radiated emissions in the open field test site at 3 m measuring distance: 30 MHz – 1.0 GHz 1.0 GHz – 18 GHz 2 Uc (E) = ± 4.32 dB 2 Uc (E) = ± 4.47 dB Test Report No.: 9212324457 Page 4 of 20 pages Title: RFID Security Information System Model: LogiRead LF One Channel Table of Contents 1. Test summary 3 2. EUT Description and operation 5 2.1. General description: 5 2.2. Potential emission sources: 8 2.3. EUT setup and operation: 8 3. Measurements, examinations and derived results 8 3.1. Location of the Test Site: 8 3.2. Test condition: 8 3.3. Initial visual check and functional test: 8 3.4. Radiated emission test. 9 3.5. Test of field strength emission from intentional radiator. 10 3.6. AC main conducted emissions test 13 3.7. Test of radiated emissions from unintentional radiator 16 4. Appendix 1. Test equipment used. 17 5. Appendix 2: Antenna Factor and Cable Loss 18 Test Report No.: 9212324457 Page 5 of 20 pages Title: RFID Security Information System Model: LogiRead LF One Channel 2. EUT Description and operation 2.1. General description: * Note: the customer supplied all information in clause below. The EUT is RFID transceiver intended for monitoring and controlling the usage of attached accessories to the applicant’s machines. RFID sub-modules shall be incorporated within the applicant’s machines, enabling them to monitor and control over the usage of the attached devices, such as, but not limited to, disposable fibers. The RFID sub-module shall have a RS-232 digital serial interface to the machine’s controller or GUI-PC. Transmit frequency: 125 kHz Type of modulation: AM Antenna type: Loop coil mfr. LogiTag mod. LT-LF The EUT is powered from power supply 15VDC. The EUT block diagram is shown in Figure 1. The EUT's views are shown in photo #1. Internal antenna impedance mathing RFID chipPIC controller RS-232 DC/DC To P.S 15VDC Signal line Loop antenna Figure 1. The EUT block-diagram. Test Report No.: 9212324457 Page 6 of 20 pages Title: RFID Security Information System Model: LogiRead LF One Channel Photo 1. EUT’s external view. Photo 2. RE test setup. Test Report No.: 9212324457 Page 7 of 20 pages Title: RFID Security Information System Model: LogiRead LF One Channel Photo 3. RE test setup on OATS. Photo 4. RE test setup on OATS. Test Report No.: 9212324457 Page 8 of 20 pages Title: RFID Security Information System Model: LogiRead LF One Channel 2.2. Potential emission sources: The potential emission sources are detailed in Table 1. Table 1. Potential emission sources Frequency Location 125 kHz RFID 16.0 MHz crystal PIC controller. 2.3. EUT setup and operation: Measurements of transmitter were performed in continue transmitting mode by using SA in Max Hold mode. 3. Measurements, examinations and derived results 3.1. Location of the Test Site: Preliminary radiated test was conducted at the EMC laboratory of the Standards Institution of Israel in Tel-Aviv. The final radiated emission test was conducted in an Open Area Test Site located at Kibbutz Native Halamed Hai in Emek HaEla, Israel. 3.2. Test condition: Temperature: 24°C. Humidity: 63 %. Atmospheric pressure: 1012 mbar. 3.3. Initial visual check and functional test: Initial visual check and brief built- in- test of the EUT was performed before testing. - No external damages were found. - The test on the EUT passed successfully. Test Report No.: 9212324457 Page 9 of 20 pages Title: RFID Security Information System Model: LogiRead LF One Channel 3.4. Radiated emission test. 3.4.1. General: Per FCC Part 15 subpart B, C Sections 15.109, 15.209 3.4.2. Preliminary radiated emission tests: Preliminary investigation measurements were performed up to tenth harmonic of fundamental in a semi-anechoic chamber at distance 3 meter. The EUT was setup in its typical c…

Text truncated - open the document above for the full version.

Test set up photos RE test setup on OATS RE test setup on OATS RE test setup on OATS (below 1 GHz) RE test setup in semi-anechoic chamber