PWN-F0101000007Proximity Reader

Version 09/2001 1 DGLI PROXIMITY READER WIRING DIAGRAM 12 V14532 Proximity reader 12Input voltage 12 V = or ~ VInput voltage 12 V = or ~ 1Data 4Common 5Red LED 3Green LED 2Buzzer FCC statement: NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: -- Reorient or relocate the receiving antenna. -- Increase the separation between the equipment and receiver. -- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. -- Consult the dealer or an experienced radio/TV technician for help. Caution: Changes or modifications not expressly approved by C.D.V.I. could void the user's authority to operate the equipment. Version 09/2001 2 Template 60 mm 96 mm 75 mm Proximity reader

Atlas Compliance & Engineering, Inc. 142 North Milpitas Blvd. PMB 376 Milpitas, California 95035 Phone 831.761.2223 Fax 831.761.3223 Federal Communication Commission Equipment Authorization Division, Application Processing Branch 7435 Oakland Mills Road Columbia, MD 21048 September 24, 2001 TO WHOM IT MAY CONCERN Pursuant to Paragraphs §0.457 and 0.459 of the Commission’s Rules (47 C.F.R.) and Section §552(b)(4) of the Freedom of Information Act, C. D. V. I. requests confidentiality for the following products: FCC ID Number Product Title/Model PWN-F0101000007 Proximity Reader/DGLI PWN-F0101000008 Proximity Reader/DGLP PWN-F0101000023 Proximity Reader/DGPROX For the product stated above, we request that the following information be held confidential: 1) Electrical Schematics and Block Diagram of the Circuitry 2) Photographs of printed circuit board and antenna. These items are potted in production and will not be available to the public. Removal of the potted material would result in a destruction of the antenna and circuit board. No other items submitted as part of the equipment authorization filing process are deemed confidential. The above exhibits contain C. D. V. I. trade secrets and proprietary information that could be of benefit to our competitors regarding the design of our proximity reader. This material is not customarily available to the general public and we request that it be withheld from public inspection. If you have any questions, please feel free to contact me at the address shown below. Sincerely, Authorized Representative Bruce Smith VP Atlas Compliance & Engineering, Inc. 142 North Milpitas Blvd. PMB376 Milpitas, CA 95035 USA 831-721-2223 tel 831-761-3223 fax [email protected]

DGLI The auxiliary proximity reader has a built-in antenna and an RFID emission field of 125 kHz. When a proximity card or key fob is presented in front of the reader, the RF field activated the cob inside the card through a modulation. The reader converts then this modulation transmitted by the proximity card or badge into a binary signal and memorize it into a 10-digit code format. Once the control unit asks the reader if a badge has been read. It replies by transmitting the code to the control unit. Then the proximity reader waits for the badge to be removed to stop the reading and reset itself.

DGLI/DGLP The auxiliary proximity reader has a built-in antenna and an RFID emission field of 125 kHz. When a proximity card or key fob is presented in front of the reader, the RF field activates the cob inside the card through a Ma nc he ste r mo dulatio n . The reader converts then this modulation transmitted at 125 kHz by the proximity card or badge into a binary signal and memorize it into a 10-digit code format. Once the control unit asks the reader if a badge has been read. It replies by transmitting the code to the control unit. Then the proximity reader waits for the badge to be removed to stop the reading and reset itself. UCA3/DGPROX The stand-alone proximity readers UCA3 and DGPROX have built-in antennas, with an RFID emission field of 125 kHz. The control unit (processor) inside the UCA3 and the DGPROX inquire the built-in reader then the auxiliary proximity reader (DGLI or DGLP). When a reader signals the presence of a proximity card or badge then it transfers the code number to the host system micro controller. The micro controller then verifies in the EEPROM if the code number is valid (code number matches one of the code in the memory). If the card or badge is not valid then the micro controller activates the buzzer (2 beeps). If the card or badge is valid then the micro controller activates the relay output (according to the output time set) and changes the LED color to green.

0134CDVdgli_subc_1 Page 1 of 23 Atlas Compliance & Engineering, Inc. 142 North Milpitas Blvd. PMB 376 Milpitas, CA 95035 Phone 831.761.2223 Fax 831.761.3223 .......... Atlas Compliance & Engineering, Inc. FCC Test Report FCC CFR 47 Part 15.207 and 15.209 COMPLIANCE CDVI 31 Ave du General Leclerc PANTIN 93500 FRANCE Product: Access Control Proximity Reader Model: DGLI Test Report Number:0134CDVdgli_subc_1 Date of Report:September 24, 2001 This report contains 23 pages and may be reproduced in full only. Partial reproduction may only be done with the written consent of Atlas Compliance & Engineering, Inc. 0134CDVdgli_subc_1 Page 2 of 23 Atlas Compliance & Engineering, Inc. 142 North Milpitas Blvd. PMB 376 Milpitas, CA 95035 Phone 831.761.2223 Fax 831.761.3223 Scope of Accreditation 0134CDVdgli_subc_1 Page 3 of 23 Atlas Compliance & Engineering, Inc. 142 North Milpitas Blvd. PMB 376 Milpitas, CA 95035 Phone 831.761.2223 Fax 831.761.3223 Table of Contents Scope of Accreditation............................................................................................................................................................2 Table of Contents....................................................................................................................................................................3 General Information................................................................................................................................................................4 Test Equipment........................................................................................................................................................................5 Test Configuration...................................................................................................................................................................6 EUT Description / Note:.....................................................................................................................................................6 EUT Support Program........................................................................................................................................................6 EUT Modifications for Compliance.................................................................................................................................6 EUT Support Devices.........................................................................................................................................................7 I/O Ports and Cables...........................................................................................................................................................7 Equipment Under Test............................................................................................................................................................8 Equipment Block Diagram...................................................................................................................................................11 Test Setup (Radiated Emissions)........................................................................................................................................12 Test Setup (Conducted Emissions).....................................................................................................................................14 Test Methods for Emissions............................................................................................................................................16 Conducted Emission Testing...........................................................................................................................................16 Temperature and Humidity..............................................................................................................................................17 Sample Calculations.........................................................................................................................................................17 FCC Part 15 Subpart C 15.207 and 15.209 Limits..........................................................................................................18 Report of Measurements Radiated Data........................................................................................................................19 Conducted Data for FCC Part 15.207(a), Line.............................................................................................................21 Conducted Data for FCC Part 15.207(a), Neutral........................................................................................................22 COMPLIANCE VERIFICATION REPORT....................................................................................................................23 Table 1 - Support Equipment Used For Test......................................................................................................................7 Table 2 - EUT Port Termination’s........................................................................................................................................7 Table 3 - Host Port Termination's.........................................................................................................................................7 Table 4 - Radiated Emission Limits, General Requirements.........................................................................................18 Table 5 - Conducted Limits..................................................................................................................................................18 Table 6 - Radiated Emission Level.....................................................................................................................................19 Table 7 - 128kHz Extrapolation Factor Data....................................................................................…

Text truncated - open the document above for the full version.