PXUIDREAM3HEAD MASSAGER

User Manual Main Unit and Remote Control 1 Main Unit, 1 Controller, 1 Power Charger, 3 Batteries, 1 User Manual, 1 Set of Earphones, 1 USB Cable Thank you for purchasing Breo iDream3. Please read this manual carefully before using the product, and keep it in a safe place for future reference. For relief of minor aches and pains iDream3 adopts air pressure, vibration, and hot compress massaging technology to massage the head and ocular regions. It comes with a wireless remote control and built-in MP3 player. You can now enjoy wonderful music while massaging, further relaxing your head and eyes. 3 Power on Open the battery cover on the back of the remote control. Place 3 AAA batteries in accordance with the positive and negative poles. Close the battery cover. (Picture1) 1. 2. 3. Music Downloading Connect the main unit to computer using the supplied USB cable; Push the power protection key on the main unit to Level “I”; Copy MP3 music to the device. 1. 2. 3. Wear Use the back dial to adjust the distance between head to establish the most comfortable fit, and wear main unit. Use the top dial in setting the distance above head. 1. 2. (picture 1) to Level “I” (picture 2) 11. 10. 2. 1. 3. 7. 4. 8. 6. 5. 9. Please make sure that one main unit is corresponding to one remote controller. The operation of encoding joint with multiply remote controller to the main unit is prohibited. EYE & HEAD MASSAGER Introduction Inside the package Main Unit Controller Function Deployment LCD Screen ON/Off Operating Buttons Air discharge DC power interface Earphone Jack Power Switch Protection key Encoding Key USB Port Size Adjusting Knob Tightness Adjusting Knob 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. Pressure Reduction Valve DC Power Port LCD ScreenFrom top to bottom: Time /Air Pressure/Vibration/Hot Compress/Music Operating Button:Clockwise: Up Button/Function Mode Next/Down Button /Function Mode Previous Center: OK Button Power switch protection key: Push left or right to turn ON/OFF MUST push power switch to Level “O” after each use Important: Make sure that only one device is paired with the remote control. Multiple pairing of remote control and main unit is strictly prohibited. Attention: In case of problem with connection between the main unit and remote control, you can perform joint encoding operation: Turn the remote control off, and push the power switch of the main unit to level “O”; Press and hold [8] encoding key of the main unit. While still holding it, push the power switch of the main unit to level “I” to turn it on; The blue LED indicator on the front of the main unit flashes. 1. 2. 3. and lights up while the main unit’s blue LED indicator turns off-it means the encoding is successful (This step should be completed within 6 Release [8] encoding key, and simultaneously press the keys of the remote control for 2-3 seconds. The remote control LCD seconds). If unsuccessful, repeat from the start. Push the power switch of the main unit to level “O”, then back to level “I”. Both the main unit and remote control should now be working. Prior to use, check the integrity of the machine and accessories: No damage on power charger Battery power is sufficient 1. 2. Preparation Attention: Push the power switch on the main unit to Level “O”. Keep the massager turned OFF while charging. Charging time is approximately 3-4 hours. If the massager is turned on while recharging, all functions of the product will run normally. The machine will automatically stop charging to prevent damage to the device. If the power of the battery is lower than 3.2 0.1V, the machine will automatically turn off. If the LED indicator of the main unit flashes, it means the lithium battery is low. Recharge the main unit. 1. 2. 3. + Manually operate related buttons to select air pressure mode, vibration mode, hot compress temperature, change music and/or massage duration. 10. 11. 12. 13. 14. 15. 16. 1 7. To clean, wipe with aseptic cotton and alcohol. Do not wash or immerse in water. This product is not a substitute for healthcare professionals' advice and treatment. In case of doubt or if necessary, please consult your healthcare professional. Please use ONLY the DC4.5V power charger that comes with the package, and handle it with care. It is very IMPORTANT to turn the power of the main unit OFF after each use and before storage to avoid damage to the machine. ProblemPossible ReasonPossible Solution Power-On Failure Weak air pressure or vibration Lithium battery of the main unit is low Lithium battery of the main unit is low Recharge the main unit at once Remote control batteries are low/ out Change batteries Remote control batteries are not installed correctly Check if positive/negative poles of batteries are positioned right Make sure the batteries are snug in place Recharge the main unit at once Power Switch Protection key is not turned on Push this key to Level “I” Ideal Environment： Temperature 5°C40°C Relative Humidity ≤80% Main UnitL282mm X W206mm X H254mm Controller L132mm X W44mm X H24mm Net Weight DC/Power： Atmospheric Pressure: 860hpa1060hpa 1125g Dimension DC: 4.5V Power: 4.5W When operational problems occur, please refer to the chart below. Do not disassemble the machine or try to repair it by yourself. Troubleshooting Specifications 2. 3. Storage If left unused, checking the product/turning the power on every 6 months is recommended. Do not store near the floor, wall or roof. Maintain good ventilation and keep away from direct sunlight and corrosive gases. Made in China Manufactured by: Shenzhen Breo Technology, Co., Ltd. Company Address: Jinshan Bldg., No. 5033, Shennan East Road, Shenzhen, 518008, China 1. Precautions 1. 2. 3. Please read the manual carefully and operate accordingly. Children under 7 years old cannot use the massager. This massager should not be used by: a. People who suffer from brain disease or have undergone brain surgery b. People who are suffering from glaucoma, retinoschisis or other serious eye disease…

Text truncated - open the document above for the full version.

Shenzhen Breo Technology Co.,Ltd. Request for Confidentiality Date: _30 OCT, 2012_______ Subject: Confidentiality Request for: ___FCC ID:_PXUIDREAM3______ Pursuant to FCC 47 CRF 0.457(d) and 0.459 and IC RSP-100, Section 10, the applicant requests that a part of the subject FCC application be held confidential. Type of Confidentiality Requested Exhibit Short Term Permanent Block Diagrams Short Term External Photos Short Term Permanent* 1 Internal Photos Short Term Permanent Operation Description/Theory of Operation Short Term Permanent Parts List & Placement/BOM Short Term Permanent Tune-Up Procedure Short Term Permanent Schematics Short Term Test Setup Photos Short Term Permanent* User’s Manual *Note: ______(Insert Explanation as Necessary)______ _ Shenzhen Breo Technology Co.,Ltd.___ has spent substantial effort in developing this product and it is one of the first of its kind in industry. Having the subject information easily available to "competition" would negate the advantage they have achieved by developing this product. Not protecting the details of the design will result in financial hardship. Permanent Confidentiality: The applicant requests the exhibits listed above as permanently confidential be permanently withheld from public review due to materials that contain trade secrets and proprietary information not customarily released to the public. Short-Term Confidentiality: The applicant requests the exhibits selected above as short term confidential be withheld from public view for a period of ___(specify number of days not to exceed 180 ) 2 ___ days from the date of the Grant of Equipment Authorization and prior to marketing. This is to avoid premature release of sensitive information prior to marketing or release of the product to the public. Applicant is also aware that they are responsible to notify PHOENIX in the event information regarding the product or the product is made available to the public. PHOENIX will then release the documents listed above for public disclosure pursuant to FCC Public Notice DA 04-1705. NOTE for Industry Canada Applications: The applicant understands that until such time that IC distinguishes between Short Term and Permanent Confidentiality, either type of marked exhibit above will simply be marked Confidential when submitted to IC. 1 - The asterisked items (*) require further justification before permanent confidentiality will be allowed. These also currently require review by the FCC under their Permit-But-Ask policy before the grant is issued and can delay completion of an application. Further justification should be added to the note above. One such example for a potted device would be: “The EUT is FULLY potted using a non-removable epoxy based material. Removal of potting material causes irreparable damage to internal circuitry. See photographs exhibits that outline the device before and after potting.” 2 - Please refer to http://acbcert.com/documents/misc-docs/Memo-Short-Term-Vs-Standard-Confidentiality.pdf for complete details.

1 Photographs - EUT Constructional Details Test Model No.: iDream3

Label content:

1 Photographs - EUT Constructional Details Test Model No.: iDream3

SGS-CSTC Standards Technical Services Co., Ltd. No. 1 W orkshop, M-10, Middle section, Science & Technology Park, Nanshan District, Shenzhen, Guangdong, China 518057 Telephone: +86 (0) 755 2601 2053 Fax: +86 (0) 755 2671 0594 Email: [email protected] Report No.: SZEM120300108302 Page : 1 of 21 Authorized Signature: Jack Zhang EMC Laboratory Manager The manufacturer should ensure that all products in series production are in conformity with the product sample detailed in this report. If the product in this report is used in any configuration other than that detailed in the report, the manufacturer must ensure the new system complies with all relevant standards. Any mention of SGS International Electrical Approvals or testing done by SGS International Electrical Approvals in connection with, distribution or use of the product described in this report must be approved by SGS International Electrical Approvals in writing. The report must not be used by the client to claim product certification, approval, or endorsement by NVLAP, NIST, or any agency of the federal government. All test results in this report can be traceable to National or International Standards. This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at www.sgs.com/terms_and_conditions.htm and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at www.sgs.com/terms_e-document.htm. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only 1 COVER PAGE FCC REPORT Application No. : SZEM1203001083RF Applicant: Shenzhen Breo Technology Co., Ltd Manufacturer: Shenzhen Breo Technology Co., Ltd Factory: Shenzhen Breo Technology Co., Ltd Product Name: HEAD MASSAGER Model No.(EUT): iDream3 FCC ID: PXUIDREAM3 Standards: 47 CFR Part 15B (2011) Date of Receipt: 2012-03-15 Date of Test: 2012-03-27 to 2012-09-24 Date of Issue: 2012-11-28 Test Result: PASS * * In the configuration tested, the EUT complied with the standards specified above. SGS-CSTC Standards Technical Services Co., Ltd. Report No.: SZEM120300108302 Page : 2 of 21 This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at www.sgs.com/terms_and_conditions.htm and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at www.sgs.com/terms_e-document.htm. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only 2 Test Summary Test Item Test Requirement Test method Result Radiated Emission 47 CFR Part 15B ANSI C63.4 (2009) PASS Conducted Emission (150KHz to 30MHz) 47 CFR Part 15B ANSI C63.4 (2009) PASS SGS-CSTC Standards Technical Services Co., Ltd. Report No.: SZEM120300108302 Page : 3 of 21 This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at www.sgs.com/terms_and_conditions.htm and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at www.sgs.com/terms_e-document.htm. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only 3 Contents Page 1 COVER PAGE........................................................................................................................................................ 1 2 TEST SUMMARY ....................................................…

Text truncated - open the document above for the full version.

1 Photographs - EUT Test Setup (Test Model No: iDream3) 1.1 Conducted Emission Test Setup 1.2 Radiatd Emission Test Setup PC mode Receiving mode