Q65LW19990824Data Collector

Beijng Landwell Electron Technology Co, Ltd L-3000EF Proximity Guard Tour System Manual This product has passed ROHS certification Important Announcement 1, Thanks for purchasing Landwell L-3000EF proximity guard tour system. Please read the manual carefully before use. When you begin to use L-3000EF guard tour reader, Landwell believes that you have read this manual carefully. 2, As the related contents of the manual may change without prior notice, the products shall prevail. For more information please check the company website （www.guard361.com/）or call us +86-01-84717640. 3, As this is a mobile patrol product, we strongly recommend that you create data backup when using. Data loss caused from hardware damage is excluded from the warranty, which is only effective for hardware itself. FCC statement: This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not in-stalled and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: —Reorient or relocate the receiving antenna. —Increase the separation between the equipment and receiver. —Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. —Consult the dealer or an experienced radio/ TV technician for help. The First Chapter This system is made up of patrol reader/communication line /Checkpoint/software. The accessories include the computer and printer. Specific steps are as follows. 1. System Directions: 1.1) Patrol reader, also called collector, is carried by patrol man during patrol rounds. Each checkpoint， collection time and patrol man name etc will be collected as one piece of data, which is saved after analysis. Then data will be uploaded to computer through communication line. 1.2) Transmitting line: also called communication line, it arranges the data within the collector and transmits them to the computer. 1.3 ) Information tag（checkpoint）────The information tag is divided into checkpoint tag and personnel tag. One information tag can only be setup as checkpoint tag or personnel tag. It cannot be setup as a personnel tag after it is already a checkpoint tag. 1.3)a checkpoint tag: according to patrol plan, a checkpoint tag stands for a patrol point, which is placed at the patrol site or equipment. Through software the information tag can be setup as different checkpoint name which it relates to. 1.3)b personnel tag: this is the patrol man‘s ID tag. Some tasks are carried out according to group of patrol man. Every group shares one reader. Every patrol man carries his own personnel tag so a reasonable patrol performance check is attainable. 1.4) Software management system ──── it analyzes the related data uploaded and after data processing, it offers detailed patrol report. The software will match the patrol report with plan, and correctly process the patrol result data. 2. Hardware Directions 2.1) Patrol reader: when patrol man reaches the planned site, he presents the reader head to the checkpoint tag within 5cm distance (the tag frequency decides the distance).When the reader sends out "beep" sound and the LED lights 3 times(the same tag cannot be reread continuously with the same reader. One minute is the minimum interval before reread. The LED will light once when reread without proper time interval ),it means the data is collected to the reader successfully. 2.2) Communication line: connect communication line USB head to the computer USB port, the other side to the reader corresponding port. 2.3) Information tag: first stir super glue(like AB glue) evenly at the rate of 1：1,spread it on the back of the patrol tag. Paste the patrol tag to the patrol point(like the surface of cement ,hard brick wall or other strong object. Choose flat surface before pasting the tag. If the surface is coarse, use sand paper to polish it.) 3. Software Setup and Usage Please read the software manual carefully before software installation. Familiarize with the software step by step. The software administer’s access is Admin, the default pin is 333. 3.1) Information tag setup: operate according to software requirement and the client demands :patrol record upload ——first clear the old data in the reader through communication line.(by transmitting the data to computer after connecting reader with computer ,the reader's stored data is cleared. The data can be retransmitted to software if the reader does not read new tag. If new tag is read, the new data will cover all the old data and it becomes the first new data record).Then use this reader to read all the checkpoint tags in order. Now upload these data to the related checkpoint setup or personnel setup. Specific operation method is as follows a Plan setup: According to the client's situation, setup the patrol route points, where the patrol tags will be fixed. b Tag reading: after checkpoint tag is installed, use the reader without data to read all the tags once, then upload the data to the …

Text truncated - open the document above for the full version.

SGS-CSTC Standards Technical Services (Shanghai) Co., Ltd. FCC ID: Q65LW19990824 Report No.: SHEM121000144202 Page: 19 of 26 This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at www.sgs.com/terms_and_conditions.htm and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at www.sgs.com/terms_e-document.htm. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only. 9 EUT Constructional Details 9.1 Exterior of EUT USB Cable Top View SGS-CSTC Standards Technical Services (Shanghai) Co., Ltd. FCC ID: Q65LW19990824 Report No.: SHEM121000144202 Page: 20 of 26 This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at www.sgs.com/terms_and_conditions.htm and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at www.sgs.com/terms_e-document.htm. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only. Rear View Left View SGS-CSTC Standards Technical Services (Shanghai) Co., Ltd. FCC ID: Q65LW19990824 Report No.: SHEM121000144202 Page: 21 of 26 This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at www.sgs.com/terms_and_conditions.htm and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at www.sgs.com/terms_e-document.htm. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only. Right View Front View SGS-CSTC Standards Technical Services (Shanghai) Co., Ltd. FCC ID: Q65LW19990824 Report No.: SHEM121000144202 Page: 22 of 26 This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at www.sgs.com/terms_and_conditions.htm and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at www.sgs.com/terms_e-document.htm. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only. Front View Remove USB Cover Back View

SGS-CSTC Standards Technical Services (Shanghai) Co., Ltd. FCC ID: Q65LW19990824 Report No.: SHEM121000144202 Page: 23 of 26 This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at www.sgs.com/terms_and_conditions.htm and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at www.sgs.com/terms_e-document.htm. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only. 9.2 Interior of EUT EUT Interior Photo Front View EUT Interior Photo Rear View SGS-CSTC Standards Technical Services (Shanghai) Co., Ltd. FCC ID: Q65LW19990824 Report No.: SHEM121000144202 Page: 24 of 26 This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at www.sgs.com/terms_and_conditions.htm and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at www.sgs.com/terms_e-document.htm. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only. PCB Front View PCB Rear View SGS-CSTC Standards Technical Services (Shanghai) Co., Ltd. FCC ID: Q65LW19990824 Report No.: SHEM121000144202 Page: 25 of 26 This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at www.sgs.com/terms_and_conditions.htm and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at www.sgs.com/terms_e-document.htm. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only. USB Connection Front View USB Connection Rear View SGS-CSTC Standards Technical Services (Shanghai) Co., Ltd. FCC ID: Q65LW19990824 Report No.: SHEM121000144202 Page: 26 of 26 This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at www.sgs.com/terms_and_conditions.htm and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at www.sgs.com/terms_e-document.htm. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only. Battery Front View Battery Rear View --End of the Report--

SGS-CSTC Standards Technical Services (Shanghai) Co., Ltd. FCC ID: Q65LW19990824 588 West Jindu Road,Songjiang District,Shanghai,China Telephone: +86 (0) 21 6191 5666 Fax: +86 (0) 21 6191 5655 [email protected] Report No.: SHEM121000144201 Page: 1 of 15 This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at www.sgs.com/terms_and_conditions.htm and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at www.sgs.com/terms_e- document.htm. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to thesample(s) tested and such sample(s) are retained for 90 days only Member of the SGS Group (SGS SA) TEST REPORT Application No. : SHEM1210001442RF Applicant: Beijing Landwell Electron Technology Co.,LTD Manufacturer: Beijing Landwell Electron Technology Co.,LTD FCC ID: Q65LW19990824 Fundamental Frequency : 125KHz Equipment Under Test (EUT): Product Name: Data Collector Model No.(EUT): L-3000 Add Model No. L-9000; L-7000; L-2000; L-2000P; L-2000PF; L-3000E; L-3000EF; L- 7000E; L-7000EF; L-9000P; L-9000PF; LW-01; LW-12; LW-24; LW-48; LW-110; LW-120; LW-150; LW-02; i-keybox12; i-keybox24; i-keybox48; i-keybox96; i-keybox120; i-keybox150 Standards: FCC PART 15 SUBPART C, Section 15.209 Date of Receipt: October 10, 2012 Date of Test: October 12, 2012 to October 17, 2012 Date of Issue: October 20, 2012 Test Result : PASS * * In the configuration tested, the EUT complied with the standards specified above. Jim Xu Neil Zhang E&E Section Head E&E Project Engineer SGS-CSTC(Shanghai) Co., Ltd. SGS-CSTC(Shanghai) Co., Ltd. SGS-CSTC Standards Technical Services (Shanghai) Co., Ltd. FCC ID: Q65LW19990824 Report No.: SHEM121000144201 Page: 2 of 15 This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at www.sgs.com/terms_and_conditions.htm and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at www.sgs.com/terms_e- document.htm. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to thesample(s) tested and such sample(s) are retained for 90 days only 2 Test Summary TEST ITEM FCC REFERANCE RESULT Field Strength of Fundamental and Radiated Emission 15.209 Pass Power Line Conducted Emission 15.207 Pass Antenna Requirement 15.203 Compliance Noted：“-”means not require in the rules. SGS-CSTC Standards Technical Services (Shanghai) Co., Ltd. FCC ID: Q65LW19990824 Report No.: SHEM121000144201 Page: 3 of 15 This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at www.sgs.com/terms_and_conditions.htm and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at www.sgs.com/terms_e- document.htm. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to thesample(s) tested and such sample(s) are retained for 90 days only 3 Contents Page 1 COVER PAGE ........................................................................................................................................... 1 2 TEST SUMMARY ......................................................................................................................................................... 2 3 CONTENTS .............................................................................................................................................................. 3 4 GENERAL INFORMATION .........................................................................…

Text truncated - open the document above for the full version.

SGS-CSTC Standards Technical Services (Shanghai)Co., Ltd. Page 2 of 3 Radiated Emission 9 kHz~30MHz 30MHz-1GHz