Q9DAPIN0754ACCESS POINT

Mark Hill Regulatory Compliance Engineer Hewlett Packard Enterprise Company [email protected] +1 408-807-0476 6280 America Center Drive San Jose, CA 95002 USA hpe.com Date: 19-Jul-2024 Federal Communications Commissions Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 RE: CFR 47 §2.911 (d)(5) Attestation FCC ID: Q9DAPIN0754 1. Hewlett Packard Enterprise Company (“the applicant”) certifies that the equipment for which authorization is sought is not “covered” equipment prohibited from receiving an equipment authorization pursuant to section 2.903 of the FCC rules. 2. Hewlett Packard Enterprise Company (“the applicant”) certifies that, as of the date of the filing of the application, the applicant is not identified on the Covered List as an entity producing “covered” equipment and is not an affiliate or subsidiary of an entity identified on the Covered List. Sincerely yours, Mark Hill Hewlett Packard Enterprise Company 6280 America Center Dr, San Jose, CA 95002 USA

Page 1 of 1 Mark Hill Regulatory Compliance Engineer Hewlett Packard Enterprise Company [email protected] +1 408 8070476 Office 6280 America Center Drive San Jose, CA 95002 USA hpe.com Date: 19-Jul-2024 DECLARATION OF CONFORMITY FCC ID: Q9DAPIN0754 Please be notified that we, the undersigned, Hewlett Packard Enterprise Company declares that the product which bears the above FCC ID is also compliant with the FCC requirements for Supplier’s Declaration of Conformity(SDoC). And the SDoC procedure shall be carried out prior to marketing the device in the US. Sincerely, ---------------------------------------------------------- Name: Mark Hill Position: Regulatory Compliance Engineer Hewlett Packard Enterprise Company

Mark Hill Regulatory Compliance Engineer Hewlett Packard Enterprise Company [email protected] +1 408-807-0476 6280 America Center Drive San Jose, CA 95002 USA hpe.com Date: 19-Jul-2024 Federal Communications Commissions Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 RE: CFR 47 §2.911 (d)(7) Agent Designation Attestation FCC ID: Q9DAPIN0754 FCC FRN: 0026486175 To whom it may concern: Hewlett Packard Enterprise Company (“the applicant”) as required by section §2.911(d)(7), will also serve as the agent for service of process for the above referenced FCC ID: Q9DAPIN0754 The applicant acknowledges that they will maintain an agent for no less than one year after the grantee has terminated all marketing and importation or the conclusion of any Commission-related proceeding involving the equipment. The applicant further acknowledges their responsibility under CFR 47 §2.929(c) to inform the FCC whenever the agent information changes. Mark Hill Hewlett Packard Enterprise Company 6280 America Center Dr, San Jose, CA 95002 USA [email protected] Sincerely yours, Mark Hill Hewlett Packard Enterprise Company 6280 America Center Dr, San Jose, CA 95002 USA

Page 1 of 1 Mark Hill Regulatory Compliance Engineer Hewlett Packard Enterprise Company [email protected] +1 408 8070476 Office 6280 America Center Drive San Jose, CA 95002 USA hpe.com Date: 10-August-2024 Professional Installation Attestation FCC ID: Q9DAPIN0754 IC: 4675A-APIN0754 TCB: Hewlett Packard Enterprise Company, declare that the above reference product is professionally installed. The APIN0754 are intended for enterprise level installations. HPE supports direct sales to large customers and sales via value-added resellers/distributors. There are no retail or mail order sales channels. In all cases, installation is performed by a trained installer. Aruba provides a certified training program. The complexity of the Aruba OS makes training a requirement for installation and operation. Without training, a user would not be able to perform the initial configuration that would enable transmission of the access points. There is a specific ordering guide that provides a list of acceptable antennas for a particular access point. This is referenced in the Installation Guide. Sign by: ---------------------------------------------------------- Name: Mark Hill Position: Regulatory Compliance Engineer Hewlett Packard Enterprise Company

Page 1 of 1 Mark Hill Regulatory Compliance Engineer Hewlett Packard Enterprise Company [email protected] +1 408 8070476 Office 6280 America Center Drive San Jose, CA 95002 USA hpe.com Date: 19-Jul-2024 ZigBee Duty Cycle Attestation Federal Communications Commission 7435 Oakland Mills Road Columbia MD 21046 FCC ID: Q9DAPIN0754 To Whom It May Concern: TCB: Hewlett Packard Enterprise Company, declare that the ZigBee operation, when implemented, will be limited to a duty cycle of 10% or less in any 100ms period. This will not be user configurable. Best Regards, Name: Mark Hill Position: Regulatory Compliance Engineer Hewlett Packard Enterprise Company

Page 1 of 2 Mark Hill Regulatory Compliance Engineer Hewlett Packard Enterprise Company [email protected] +1 408 8070476 Office 6280 America Center Drive San Jose, CA 95002 USA hpe.com Date: 19-Jul-2024 Federal Communications Commission 7435 Oakland Mills Road Columbia MD 21046 To whom it may concern: I, the undersigned, hereby authorize MRT Technology (Suzhou) Co., Ltd to act on our behalf in all manners relating to application for equipment authorization, including signing of all documents relating to these matters. Any and all acts carried out by MRT Technology (Suzhou) Co., Ltd on our behalf shall have the same effect as acts of our own. I, the undersigned, hereby certify that we are not subject to a denial of federal benefits, that includes FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C. 853(a). In authorizing MRT Technology (Suzhou) Co., Ltd as our representative, we still recognize that we are responsible to: a) comply with the relevant provisions of the certification program; b) make all necessary arrangements for the conduct of the evaluation, including provision for examining documentation and access to all areas, records (including internal audit reports) and personnel for the purposes of evaluation (e.g. testing, inspection, assessment, surveillance, reassessment) and resolution of complaints; c) make claims regarding certification only in respect of the scope for which certification has been granted; d) do not use our product certification in such a manner as to bring the Certification Division into disrepute and not make any statement regarding our product certification which the Certification Division may consider misleading or unauthorized; e) upon suspension or cancellation of certification, discontinue use of all advertising matter that contains any reference thereto and return any certification documents as required by the Certification Division; f) use certification only to indicate the products are certified as being in conformity with specified standards; g) endeavor to ensure that no certificate or report nor any part thereof is used in a misleading manner; h) ensure that any reference to our product certification in communication media such as documents, brochures or advertising, complies with the requirements of the Certification Division; i) keep a record of all complaints made known to us relating to the product’s compliance with requirements of the relevant standard and to make these records available when requested; Page 2 of 2 Mark Hill Regulatory Compliance Engineer Hewlett Packard Enterprise Company [email protected] +1 408 8070476 Office 6280 America Center Drive San Jose, CA 95002 USA hpe.com j) take appropriate action with respect to such complaints and any deficiencies found in products or services that affect compliance with the requirements for certification; k) document the actions taken. This authorization is valid until further written notice from the applicant. Sincerely Yours, Name: Mark Hill Position: Regulatory Compliance Engineer Hewlett Packard Enterprise Company

Page 1 of 2 Mark Hill Regulatory Compliance Engineer Hewlett Packard Enterprise Company [email protected] +1 408 8070476 Office 6280 America Center Drive San Jose, CA 95002 USA hpe.com Date: 19-Jul-2024 Federal Communications Commission 7435 Oakland Mills Road Columbia MD 21046 Subject: Request for Confidentiality FCC ID: Q9DAPIN0754 To Whom It May Concern: Pursuant to the provisions of Sections 0.457 and 0.459 of the Commission’s rules (47 CFR §§ 0.457, 0.459), we are requesting the Commission to withhold the following attachments as confidential document from public disclosure indefinitely. Schematic Diagram Block Diagram Theory of Operation Software Security Requirements Cover Letter Above mentioned document contains detailed system and equipment description are considered as proprietary information in operation of the equipment. The public disclosure of above documents might be harmful to our company and would give competitor an unfair advantage in the market. In additional to above mentioned documents, pursuant to Public Notice DA 04-1705 of the Commission’s policy, in order to comply with the marketing regulations in 47 CFR §2.803 and the importation rules in 47 CFR §2.1204, while ensuring that business sensitive information remains confidential until the actual marketing of newly authorized devices. We are requesting the commission to grant short-term confidentiality request on the following attachments until (180 days): External Photos Internal Photos Test Setup Photos User Manual It is our understanding that all measurement test reports, FCC ID label format and correspondent during certification review process cannot be granted as confidential documents and those information will be available for public review once the grant of equipment authorization is issued. Page 2 of 2 Mark Hill Regulatory Compliance Engineer Hewlett Packard Enterprise Company [email protected] +1 408 8070476 Office 6280 America Center Drive San Jose, CA 95002 USA hpe.com Best Regards, Name: Mark Hill Position: Regulatory Compliance Engineer Hewlett Packard Enterprise Company

FRELEASE SANDY CHEN06/18/24 WNC CONFIDENTIAL LASER ENGRAVING,4013960-03,AGENCY , AP-754,R7PB-A1 F 2 CATHY CHEN06/18/24 06/18/24 CATHY CHEN 06/18/24 SANDY CHEN *1 *2 3 4 44.2 69.2 3±0.5 3±0.5

MRT Technology (Suzhou) Co., Ltd Report No.: 2403RSU068-U16 Phone: +86-512-66308358 Report Version: V02 Web: www.mrt-cert.com Issue Date: 2024-08-19 Template Version:0.1 1 of 13 RF Exposure Evaluation Declaration FCC ID: Q9DAPIN0754 Applicant: Hewlett Packard Enterprise Company Product: ACCESS POINT Model No.: APIN0754 Trademark: FCC Rule Part(s): FCC Part 2.1091 Result: Complies Evaluation Date: 2024-07-30 Reviewed By: Jame Yuan Approved By: Robin Wu The test results relate only to the samples tested. The test results shown in the test report are traceable to the national/international standards through the calibration of the equipment and evaluated measurement uncertainty herein. The test report shall not be reproduced except in full without the written approval of MRT Technology (Suzhou) Co., Ltd. Report No.: 2403RSU068-U16 2 of 13 Revision History Report No. Version Description Issue Date Note 2403RSU038-U16 V01 Initial Report 2024-07-30 Invalid 2403RSU038-U16 V02 Updated the antenna list 2024-08-19 Valid Report No.: 2403RSU068-U16 3 of 13 CONTENTS Description Page 1. General Information ............................................................................................................................... 4 1.1. Applicant ........................................................................................................................................4 1.2. Manufacturer .................................................................................................................................4 1.3. Testing Facility ...............................................................................................................................4 1.4. Product Information .......................................................................................................................5 1.5. Antenna Details .............................................................................................................................6 1.6. Device Classification .....................................................................................................................7 1.7. Applied Standards .........................................................................................................................7 2. RF Exposure Evaluation ........................................................................................................................ 8 2.1. Test Limit .......................................................................................................................................8 2.2. MPE Exemptions ...........................................................................................................................9 2.3. Calculated Result ....................................................................................................................... 12 Report No.: 2403RSU068-U16 4 of 13 1. General Information 1.1. Applicant Hewlett Packard Enterprise Company 6280 America Center Drive, San Jose CA 95002, United States 1.2. Manufacturer Hewlett Packard Enterprise Company 6280 America Center Drive, San Jose CA 95002, United States 1.3. Testing Facility Test Site – MRT Suzhou Laboratory Laboratory Location (Suzhou - Wuzhong) D8 Building, No.2 Tian’edang Rd., Wuzhong Economic Development Zone, Suzhou, China Laboratory Location (Suzhou - SIP) 4b Building, Liando U Valley, No.200 Xingpu Rd., Shengpu Town, Suzhou Industrial Park, China Laboratory Accreditations A2LA: 3628.01 CNAS: L10551 FCC: CN1166 ISED: CN0001 VCCI: R-20025 G-20034 C-20020 T-20020 R-20141 G-20134 C-20103 T-20104 Test Site – MRT Shenzhen Laboratory Laboratory Location (Shenzhen) 1G, Building A, Junxiangda Building, Zhongshanyuan Road West, Nanshan District, Shenzhen, China Laboratory Accreditations A2LA: 3628.02 CNAS: L10551 FCC: CN1284 ISED: CN0105 Test Site – MRT Taiwan Laboratory Laboratory Location (Taiwan) No. 38, Fuxing 2nd Rd., Guishan Dist., Taoyuan City 333, Taiwan (R.O.C.) Laboratory Accreditations TAF: 3261 FCC: 291082, TW3261 ISED: TW3261 Report No.: 2403RSU068-U16 5 of 13 1.4. Product Information Product Name ACCESS POINT Model No. APIN0754 Wi-Fi Specification 802.11a/b/g/n/ac/ax/be Bluetooth Specification BLE only ZigBee Specification 802.15.4 GNSS Specification GPS, Galileo Antenna Information Refer to Section 1.5 Power Type AC Adapter Input or PoE Input Operating Environment Indoor Use Remark: The information of EUT was provided by the manufacturer, and the accuracy of the information shall be the responsibility of the manufacturer. Report No.: 2403RSU068-U16 6 of 13 1.5. Antenna Details Polarization Antenna Name Frequency Band (GHz) Max Peak Gain (dBi) CDD Dir Gain (dBi) BF Dir Gain (dBi) For Power For PSD Wi-Fi External Antenna List (4*4 MIMO) Omni AP-ANT-311 2.4 ~ 2.5 3.0 3.0 9.02 9.02 5.15 ~ 5.9 6.0 6.0 12.02 12.02 5.9 ~ 7.2 6.0 6.0 12.02 12.02 Omni AP-ANT-312 2.4 ~ 2.5 3.3 3.3 9.32 9.32 5.15 ~ 5.9 3.3 3.3 9.32 9.32 5.9 ~ 7.2 4.1 4.1 10.12 10.12 Omni AP-ANT-313 2.4 ~ 2.5 3.0 3.0 9.02 9.02 5.15 ~ 5.9 6.0 6.0 12.02 12.02 5.9 ~ 7.2 6.0 6.0 12.02 12.02 Omni AP-ANT-340 2.4 ~ 2.5 4.0 4.0 10.02 10.02 5.15 ~ 5.9 5.0 5.0 11.02 11.02 5.9 ~ 7.2 5.0 5.0 11.02 11.02 Directional (Note 4) AP-ANT-345 2.4 ~ 2.5 6.1 6.1 9.11 9.11 5.15 ~ 5.9 6.1 6.1 9.11 9.11 5.9 ~ 7.2 5.4 5.4 8.41 8.41 Directional (Note 4) AP-ANT-348 2.4 ~ 2.5 7.5 7.5 10.51 10.51 5.15 ~ 5.9 8.0 8.0 11.01 11.01 5.9 ~ 7.2 8.0 8.0 11.01 11.01 Note: 1, The EUT supports Cyclic Delay Diversity (CDD) mode, and CDD signals are correlated. If all antennas have the same gain, G ANT , Directional gain = G ANT + Array Gain, where Array Gain is as follows. • For power spectral density (PSD) measurements on all devices, Array Gain = 10 log (N ANT / N SS ) dB = 3.01; • For power measurements on IEEE 802.11 devices, Array Gain = 0 dB for N ANT ≤ 4; 2, The EUT also supports Beam Forming mode, and the Beam Forming support 802.11n/ac/ax/be, not include 802.11a/b/g. 3, The antenna specification is provided by th…

Text truncated - open the document above for the full version.

Doc.No.:3.8.05 Rev Regulatory WIFI Antenna Information 1/25 Antenna Composite Gain Test Report 1. Test Information Equipment Campus Access Points Brand Name Aruba Model Name AP754 Applicant Aruba Manufacturer Aruba 2. Testing Location Testing Location WNC ADD：20 Park Ave. ll, Hsinchu Science Park, Hsinchu 308 Taiwan Test Condition Test Engineer Test Environment ( O C / %) Test Date Radiated Leo Chuang 20-24 / 45-60 05.01.2024~05.13.2024 3. Test Frequency Band (MHz) Test Frequency (MHz) 1165-1185 1176 1560-1590 1575 2401-2423 2401 2441-2463 2452 2473-2484 2484 4. Antenna Information Ant. Position Brand Name Model Name Ant. Type Connector Antenna 1 (BLE) Aruba 95XPAD15.GAG PIFA I-PEX Antenna 2 (BLE) Aruba 95XPAD15.GAH PIFA I-PEX Antenna 3 (GPS) Aruba 95XPAD15.G50 PIFA I-PEX Antenna 4 (BLE) Aruba 95XPAD15.G51 Alford Loop I-PEX Doc.No.:3.8.05 Rev Regulatory WIFI Antenna Information 2/25 5. Test Configuration ETS-AMS 8500 System Item Device Type/Model Serial# Manufacturer Cal. Date Cal. Due Date 1 Anechoic Chamber ETS-AMS 8500 ETS-Lindgren 2024/03/09 2025/03/08 2 Turn Table ETS ETS-Lindgren 2024/03/09 2025/03/08 3 Multi-Device Positioning Controller Model 2090 142407 ETS-Lindgren 2024/03/09 2025/03/08 4 Network Analyzer E5071C 0171E5485A6J Keysight 2023/05/31 2024/05/30 5 Horn antenna 3164-08 140264 ETS-Lindgren 2024/03/09 2025/03/08 6 Cable 7.5m 400MHz to 18GHz (H-pol) SS402 00100A1F5A1XXS Woken 2024/03/09 2025/03/08 7 Cable 7.5m 400MHz to 18GHz (V-pol) SS402 00100A1F5A1XXS Woken 2024/03/09 2025/03/08 8 Cable 14m 400MHz to 18GHz SS402 00100A1F5A1XXS Woken 2024/03/09 2025/03/08 9 Temperature & Humidity Meter HTC-01 Metravi 2024/03/09 2025/03/08 Doc.No.:3.8.05 Rev Regulatory WIFI Antenna Information 3/25 6. Reference Calibration 7. Test Method The “great circle” cut method, whereby the Measurement Antenna remains fixed and the EUT is rotated about two axes in sequential order.The radiated RF performance of the Equipment Under Test (EUT) is measured by sampling the radiated transmit power of the mobile at various locations surrounding the device. A three-dimensional characterization of the 'transmit' performance of the EUT is pieced together by analyzing the data from the spatially distributed measurements. Data points taken every 15 degrees in the theta and in the phi axes are deemed sufficient to fully characterize the EUT's Far-Field radiation pattern and total radiated power All of the measured power values will be integrated Doc.No.:3.8.05 Rev Regulatory WIFI Antenna Information 4/25 8. Measured Values and Calculation of Correlated / Uncorrelated Gains Antenna Peak Gain Table (Ant. Position：GPS Ant.3) Band (MHz) 1165-1185 1560-1590 Frequency (MHz) 1176 1575 Ant.3 Max Gain (dBi) 2.8 3.0 Antenna Peak Gain Table (Ant. Position：BLE Ant.1~2, 4) Band (MHz) 2401-2423 2441-2463 2473-2484 Frequency (MHz) 2401 2452 2484 Ant.1 Max Gain (dBi) 2.3 4.5 5.6 Ant.2 Max Gain (dBi) 2.8 3.3 3.2 Ant.4 Max Gain (dBi) 4.8 5.0 4.7 Max Gain (dBi) 4.8 5.0 5.6 Antenna Correlated / Uncorrelated Gain Table (Ant. Position：BLE Ant.1, 4) Frequency (MHz) Correlated Gain (dBi) Uncorrelated Gain (dBi) 2401 5.4 2.4 2452 6.6 3.6 2484 7.0 4.2 Antenna Correlated / Uncorrelated Gain Table (Ant. Position：BLE Ant.1~2) Frequency (MHz) Correlated Gain (dBi) Uncorrelated Gain (dBi) 2401 5.3 2.3 2452 6.1 3.1 2484 7.1 4.2 Doc.No.:3.8.05 Rev Regulatory WIFI Antenna Information 5/25 Because the antennas are fixed in location within the device the directional antenna gain for MIMO is calculated over a sphere using the raw spatial data taken at 5 degree steps of theta and phi for each antenna using the equations from KDB 662911 D01. The raw antenna data is located in the appendix of this report. The correlated antenna gain was calculated using KDB 662911 D01, F(2)(d)(i). The uncorrelated antenna gain was calculated using KDB 662911 D01, F(2)(d)(ii). The uncorrelated and correlated gains were calculated for each point in the spatial data, and the highest values reported. Note： KDB 662911 D01, F(2)(d)(i) KDB 662911 D01, F(2)(d)(ii) N Ant. ：Number of antenna G n ：Gain of antenna Correlated Gain Uncorrelated Gain Doc.No.:3.8.05 Rev Regulatory WIFI Antenna Information 6/25 Maximum Correlated / Uncorrelated Gain Calculation (Ant. Position：BLE Ant.1, 4) Frequency (MHz) 2484 Ant.1 Gain (dBi) 5.59 Ant.4 Gain (dBi) 2.09 Phi (〫) 150 Theta (〫) 55 Corr. Ant. Gain (dBi) [10^(G 1 /20)+10^(G 2 /20)] 2 /N ANT. 5.04 Uncor. Ant. Gain (dBi) [10^(G 1 /10)+10^(G 2 /10)]/N ANT. 2.62 Corr. Gain (dBi) 10*log(Corr. Ant. Gain) 7.0 Uncor. Gain (dBi) 10*log(Uncor. Ant. Gain) 4.2 (Ant. Position：BLE Ant.1~2) Frequency (MHz) 2484 Ant.1 Gain (dBi) 5.38 Ant.4 Gain (dBi) 2.51 Phi (〫) 155 Theta (〫) 55 Corr. Ant. Gain (dBi) [10^(G 1 /20)+10^(G 2 /20)] 2 /N ANT. 5.09 Uncor. Ant. Gain (dBi) [10^(G 1 /10)+10^(G 2 /10)]/N ANT. 2.61 Corr. Gain (dBi) 10*log(Corr. Ant. Gain) 7.1 Uncor. Gain (dBi) 10*log(Uncor. Ant. Gain) 4.2 Note：Antenna gain is the correlated / uncorrelated gain position in the appendix gain table. Doc.No.:3.8.05 Rev Regulatory WIFI Antenna Information 7/25 9. Test Setup Note： Top cover toward +Z direction Doc.No.:3.8.05 Rev Regulatory WIFI Antenna Information 8/25 10. Radiation Pattern Ant. Position：BLE Ant.1~2, 4 XY_Pol._Phi_Ant.1 XY_Pol._Phi_Ant.2 Doc.No.:3.8.05 Rev Regulatory WIFI Antenna Information 9/25 XY_Pol._Phi_Ant.4 XY_Pol._Theta_Ant.1 Doc.No.:3.8.05 Rev Regulatory WIFI Antenna Information 10/25 XY_Pol._Theta_Ant.2 XY_Pol._Theta_Ant.4 Doc.No.:3.8.05 Rev Regulatory WIFI Antenna Information 11/25 XZ_Pol._Phi_Ant.1 XZ_Pol._Phi_Ant.2 Doc.No.:3.8.05 Rev Regulatory WIFI Antenna Information 12/25 XZ_Pol._Phi_Ant.4 XZ_Pol._Theta_Ant.1 Doc.No.:3.8.05 Rev Regulatory WIFI Antenna Information 13/25 XZ_Pol._Theta_Ant.2 XZ_Pol._Theta_Ant.4 Doc.No.:3.8.05 Rev Regulatory WIFI Antenna Information 14/25 YZ_Pol._Phi_Ant.1 YZ_Pol._Phi_Ant.2 Doc.No.:3.8.05 Rev Regulatory WIFI Antenna Information 15/25 YZ_Pol._Phi_Ant.4 YZ_Pol._Theta_Ant.1 Doc.No.:3.8.05 Rev Regulatory WIFI A…

Text truncated - open the document above for the full version.

MRT Technology (Suzhou) Co., Ltd Report No.:2403RSU068-U11 Phone: +86-512-66308358 Report Version: V01 Web: www.mrt-cert.com Issue Date: 2024-08-01 Template Version:0.0 1 of 784 RF MEASUREMENT REPORT FCC ID: Q9DAPIN0754 Applicant: Hewlett Packard Enterprise Product: ACCESS POINT Model No.: APIN0754 Trademark: FCC Classification: Digital Transmission System (DTS) FCC Rule Part(s): Part 15 Subpart C (Section 15.247) Result: Complies Received Date: 2024-03-29 Test Date: 2024-05-23 ~ 2024-07-31 Reviewed By: Jame Yuan Approved By: Robin Wu The test results relate only to the samples tested. This equipment has been shown to be capable of compliance with the applicable technical standards as indicated in the measurement report and was tested in accordance with the measurement procedures specified in ANSI C63.10-2013. Test results reported herein relate only to the item(s) tested. The test report shall not be reproduced except in full without the written approval of MRT Technology (Suzhou) Co., Ltd. Report No.: 2403RSU068-U11 2 of 784 Revision History Report No. Version Description Issue Date Note 2403RSU068-U11 V01 Initial Report 2024-08-01 Valid Report No.: 2403RSU068-U11 3 of 784 CONTENTS Description Page 1. General Information ................................................................................................................................ 6 1.1. Applicant ...................................................................................................................................... 6 1.2. Manufacturer ................................................................................................................................ 6 1.3. Testing Facility ............................................................................................................................. 6 1.4. Product Information ...................................................................................................................... 7 1.5. Radio Specification under Test .................................................................................................... 7 1.6. Working Frequencies ................................................................................................................... 8 1.7. Description of Operating Paths .................................................................................................... 9 1.8. Antenna Details ............................................................................................................................ 9 1.9. Description of Antenna RF Port ................................................................................................. 10 2. Test Configuration ................................................................................................................................. 11 2.1. Test Mode .................................................................................................................................... 11 2.2. Test System Connection Diagram............................................................................................... 11 2.3. Test Software ............................................................................................................................. 12 2.4. Applied Standards ...................................................................................................................... 12 2.5. Test Environment Condition ....................................................................................................... 12 3. Antenna Requirements ......................................................................................................................... 13 4. Measuring Instrument ........................................................................................................................... 14 5. Decision Rules and Measurement Uncertainty .................................................................................. 16 5.1. Decision Rules ........................................................................................................................... 16 5.2. Measurement Uncertainty .......................................................................................................... 16 6. Test Result .............................................................................................................................................. 17 6.1. Summary .................................................................................................................................... 17 6.2. 6dB Bandwidth Measurement .................................................................................................... 18 6.2.1. Test Limit .................................................................................................................................... 18 6.2.2. Test Procedure ........................................................................................................................... 18 6.2.3. Test Setting ................................................................................................................................ 18 6.2.4. Test Setup .................................................................................................................................. 18 6.2.5. Test Result ................................................................................................................................. 18 6.3. Output Power Measurement ...................................................................................................... 19 6.3.1. Test Limit .................................................................................................................................... 19 6.3.2. Test Procedure ........................................................................................................................... 19 6.3.3. Test Setting ......................................................................…

Text truncated - open the document above for the full version.

Report No.: 2403RSU068-U11 68 of 784 BLE-2Mbps Out-of-Band Emissions Channel 00 (2402MHz) 100kHz PSD Reference Level Low Band Edge Spurious Emission 30MHz ~ 25GHz Report No.: 2403RSU068-U11 69 of 784 Test Site WZ-SR5 Test Engineer Luis Yang Test Date 2024-06-02 Filter 3# Test Mode Data Rate / Mbps Channel No. Frequency (MHz) Limit (dBc) Result BLE 1 39 2480 20 Pass BLE 2 39 2480 20 Pass BLE-1Mbps Out-of-Band Emissions Channel 39 (2480MHz) 100kHz PSD Reference Level High Band Edge Spurious Emission 30MHz ~ 25GHz Report No.: 2403RSU068-U11 70 of 784 BLE-2Mbps Out-of-Band Emissions Channel 39 (2480MHz) 100kHz PSD Reference Level High Band Edge Spurious Emission 30MHz ~ 25GHz Report No.: 2403RSU068-U11 71 of 784 Mode 2 Test Site WZ-SR5 Test Engineer Luis Yang Test Date 2024-06-02 Filter 4# Test Mode Data Rate / Mbps Channel No. Frequency (MHz) Limit (dBc) Result BLE 1 00 2402 20 Pass BLE 1 19 2440 20 Pass BLE 1 39 2480 20 Pass BLE 2 00 2402 20 Pass BLE 2 19 2440 20 Pass BLE 2 39 2480 20 Pass BLE-1Mbps Out-of-Band Emissions Channel 00 (2402MHz) 100kHz PSD Reference Level Low Band Edge Spurious Emission 30MHz ~ 25GHz Report No.: 2403RSU068-U11 72 of 784 Channel 19 (2440MHz) 100kHz PSD Reference Level Spurious Emission 30MHz ~ 25GHz Channel 39 (2480MHz) 100kHz PSD Reference Level High Band Edge Spurious Emission 30MHz ~ 25GHz Report No.: 2403RSU068-U11 73 of 784 BLE-2Mbps Out-of-Band Emissions Channel 00 (2402MHz) 100kHz PSD Reference Level Low Band Edge Spurious Emission 30MHz ~ 25GHz Channel 19 (2440MHz) 100kHz PSD Reference Level Spurious Emission 30MHz ~ 25GHz Report No.: 2403RSU068-U11 74 of 784 Channel 39 (2480MHz) 100kHz PSD Reference Level High Band Edge Spurious Emission 30MHz ~ 25GHz Report No.: 2403RSU068-U11 75 of 784 Test Site WZ-SR5 Test Engineer Luis Yang Test Date 2024-06-02 Filter 5# Test …

Text truncated - open the document above for the full version.