QB9E1107Restaurant Tablet

eTab International, Inc. eTab Device User Manual 7 inch and 5 inch devices Version 1.1 Document Number: TD0025 Approval Date: 10-04-2012 Author: Veronica M. Villareal Confidential Information The information contained in this document is e|tab International, Inc. confidential and has been prepared to establish internal policies and procedures. Distribution of this document outside of e|tab International Inc. is strictly prohibited. Do not copy or distribute without the permission of the Chief Executive Officer. Document Owners Veronica M. Villareal Manager – Office, QA, Menu Building, & Compliance eTab International, Inc. Page 2 of 8 Revision Log Version Description of Change Author Date 1.0 Initial Release Veronica M. Villareal 10-04-2012 1.1 Add FCC Statement Veronica M. Villareal 10-10-2012 Page 3 of 8 Table of Contents 1 FCC Statement ...................................................................................................................................... 4 2 Introduction ............................................................................................................................................ 4 2.1 Turn on Devices ............................................................................................................................ 5 2.2 Turn off Devices ............................................................................................................................ 6 2.3 Change Battery on Devices .......................................................................................................... 7 2.4 General Care Cleaning ................................................................................................................. 8 Page 4 of 8 1 FCC Statement Any modifications to the unit, unless expressly approved by eTab, could void the user's authority to operate the equipment. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device , pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try and correct the interference by one or more of the following measures: • Reorient or locate the receiving antenna. • Increase the separation between the equipment and receiver. • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. • Consult the dealer or an experienced radio/TV technician for help. This device has been tested and found to comply with the FCC RF Exposure requirements. 2 Introduction This document will provide general instruction on how to operate the eTab 7 inch and 5 inch devices as follows: • Turn on devices • Change battery on devices • General care and cleaning Note: Instructions provided in this user guide apply to both the 7 inch and 5 inch eTab devices. Page 5 of 8 2.1 Turn on Devices Follow these instructions for turning on the 5 and 7 inch devices: 1. Use the end of a paper clip for powering on the device. 2. Insert the end of the paper clip into the small hole in the back of the device; hold until you feel the power button click. 3. Hold the power button down until the device turns on; then release the paper clip. Page 6 of 8 2.2 Turn off Devices Follow these instructions for turning on the 5 and 7 inch devices: 1. Use the end of a paper clip for powering off the device. 2. Insert the end of the paper clip into the small hole in the back of the device; hold until you feel the power button click. 3. Hold the power button down until the device turns off; then release the paper clip. Page 7 of 8 2.3 Change Battery on Devices Follow these instructions for changing the battery on the 5 and 7 inch devices: 1. On the back of the device, pull down the battery release latch. 2. While pulling down the release latch, slide the battery out of the device. 3. Slide a fully charged battery into the battery slot until the latch clicks. Page 8 of 8 2.4 General Care Cleaning To clean the devices, use a damp soft cloth to wipe the front and back of the devices. Note: Do not use any harsh or abrasive cleaners.

Page 1 of 1 Elliott TCB 41039 Boyce Road Fremont, CA, 94538 To whom it may concern: The enclosed documents constitute a formal submittal and application for Equipment Authorization for a restaurant stand up tablet with Wi-Fi Radio including SAR evaluation pursuant to the following rules: Subpart C of Part 15 of FCC Rules (CFR 47), Intentional Radiators Elliott Laboratories, as duly authorized agent prepared this submittal. A copy of the letter of our appointment as agent is included with the application. If there are any questions or if further information is needed, please contact Elliott Laboratories for assistance. Sincerely, David W. Bare Chief Engineer DWB/dmg

802 N. Twin Oaks Valley Road, Suite 105 • San Marcos, CA 92069 • U.S.A. TEL (760) 471-2100 • FAX (760) 471-2121 http://www.rfexposurelab.com CERTIFICATE OF COMPLIANCE SAR EVALUATION eTab Dates of Test: September 27, 2012 5017 Washington Place, Suite 202 Test Report Number: SAR.20120907 St. Louis, MO 63108 FCC ID: QB9E1107 Model(s): E1107 Contains WLAN Model(s): Atheros Module Test Sample: Engineering Unit Same as Production Serial Number: 00027FEA22B1 Equipment Type: Wireless Module Installed in Tablet Classification: Portable Transmitter Next to Body TX Frequency Range: 2412 – 2462 MHz Frequency Tolerance: ± 2.5 ppm Maximum RF Output: 2450 MHz (b) – 13.1 dB, 2450 MHz (g) – 12.3 dB Radiated Signal Modulation: DSSS, OFDM Antenna Type: Pulse, P/N W3008C; PIFA Antenna Application Type: Certification FCC Rule Parts: Part 2, 15C KDB Test Methodology: KDB 447498, KDB 248227, KDB 616217 Industry Canada: RSS-102, Safety Code 6 Maximum SAR Value: 0.197 W/kg Separation Distance: 0 mm This wireless mobile and/or portable device has been shown to be compliant for localized specific absorption rate (SAR) for uncontrolled environment/general exposure limits specified in ANSI/IEEE Std. C95.1-1992 and had been tested in accordance with the measurement procedures specified in IEEE 1528-2003, and OET Bulletin 65 Supp. C (See test report). I attest to the accuracy of the data. All measurements were performed by myself or were made under my supervision and are correct to the best of my knowledge and belief. I assume full responsibility for the completeness of these measurements and vouch for the qualifications of all persons taking them. RF Exposure Lab, LLC certifies that no party to this application is subject to a denial of Federal benefits that includes FCC benefits pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C. 853(a). Jay M. Moulton Vice President Certificate # 2387.01 © 2012 RF Exposure Lab, LLC This report shall not be reproduced except in full without the written approval of RF Exposure Lab, LLC. FCC ID: QB9E1107 Table of Contents 1. Introduction ........................................................................................................................... 3 SAR Definition [5] ...................................................................................................................... 3 2. SAR Measurement Setup ..................................................................................................... 4 Robotic System ......................................................................................................................... 4 System Hardware ..................................................................................................................... 4 System Electronics ................................................................................................................... 5 Probe Measurement System ..................................................................................................... 5 3. Probe and Dipole Calibration .............................................................................................. 10 4. Phantom & Simulating Tissue Specifications ...................................................................... 11 Head & Body Simulating Mixture Characterization ................................................................. 11 Device Holder ......................................................................................................................... 11 5. ANSI/IEEE C95.1 – 1992 RF Exposure Limits [2] ............................................................... 12 Uncontrolled Environment ....................................................................................................... 12 Controlled Environment .......................................................................................................... 12 6. Measurement Uncertainty ................................................................................................... 13 7. System Validation ............................................................................................................... 14 Tissue Verification ................................................................................................................... 14 Test System Verification ......................................................................................................... 14 8. SAR Test Data Summary .................................................................................................... 15 Procedures Used To Establish Test Signal ............................................................................. 15 Device Test Condition ............................................................................................................. 15 SAR Data Summary – 2450 MHz Body 802.11b .................................................................... 18 9. Test Equipment List ............................................................................................................ 19 10. Conclusion ...................................................................................................................... 20 11. References ...................................................................................................................... 21 Appendix A – System Validation Plots and Data ........................................................................ 22 Appendix B – SAR Test Data Plots ............................................................................................. 25 Appendix C – SAR Test Setup Photos ....................................................................................... 30 Appendix D – Probe Calibration Data Sheets ............................................................................. 34 Appendix E – Dipole Calibration Data Sheets ............................................................................ 46 Appendix…

Text truncated - open the document above for the full version.

File: R89342 Page 1 EMC Test Report Application for Grant of Equipment Authorization FCC Part 15 Subpart C Model: E1107 FCC ID: QB9E1107 APPLICANT: eTab 5017 Washington Place, Ste 202 St. Louis, MO 63108 TEST SITE(S): NTS Silicon Valley 41039 Boyce Road. Fremont, CA. 94538-2435 IC SITE REGISTRATION #: 2845B-3; 2845B-5 REPORT DATE: December 31, 2012 FINAL TEST DATES: September 6, 10, 11 and December 31, 2012 TOTAL NUMBER OF PAGES: 45 PROGRAM MGR / QUALITY ASSURANCE DELEGATE / TECHNICAL REVIEWER: FINAL REPORT PREPARER: ______________________________ ______________________________ David W. Bare David Guidotti Chief Engineer Senior Technical Writer NTS Silicon Valley is accredited by the A2LA, certificate number 0214.26, to perform the test(s) listed in this report, except where noted otherwise. This report and the information contained herein represent the results of testing test articles identified and selected by the client performed to specifications and/or procedures selected by the client. National Technical Systems (NTS) makes no representations, expressed or implied, that such testing is adequate (or inadequate) to demonstrate efficiency, performance, reliability, or any other characteristic of the articles being tested, or similar products. This report should not be relied upon as an endorsement or certification by NTS of the equipment tested, nor does it represent any statement whatsoever as to its merchantability or fitness of the test article, or similar products, for a particular purpose. This report shall not be reproduced except in full NTS Silicon Valley -- EMC Department Test Report Report Date: December 31, 2012 File: R89342 Page 2 REVISION HISTORY Rev# Date Comments Modified By - 12-31-2012 First release NTS Silicon Valley -- EMC Department Test Report Report Date: December 31, 2012 File: R89342 Page 3 TABLE OF CONTENTS REVISION HISTORY ................................................................................................................................................ 2 TABLE OF CONTENTS ............................................................................................................................................ 3 SCOPE .......................................................................................................................................................................... 4 OBJECTIVE ................................................................................................................................................................ 4 STATEMENT OF COMPLIANCE ........................................................................................................................... 5 DEVIATIONS FROM THE STANDARDS .............................................................................................................. 5 TEST RESULTS SUMMARY ................................................................................................................................... 6 DIGITAL TRANSMISSION SYSTEMS (2400 – 2483.5MHZ) .............................................................................. 6 GENERAL REQUIREMENTS APPLICABLE TO ALL BANDS .......................................................................... 7 MEASUREMENT UNCERTAINTIES .................................................................................................................... 7 EQUIPMENT UNDER TEST (EUT) DETAILS ...................................................................................................... 8 GENERAL ................................................................................................................................................................ 8 ANTENNA SYSTEM .............................................................................................................................................. 8 ENCLOSURE ........................................................................................................................................................... 8 MODIFICATIONS ................................................................................................................................................... 8 SUPPORT EQUIPMENT ......................................................................................................................................... 8 EUT INTERFACE PORTS ...................................................................................................................................... 8 EUT OPERATION ................................................................................................................................................... 8 TEST SITE ................................................................................................................................................................... 9 GENERAL INFORMATION ................................................................................................................................... 9 CONDUCTED EMISSIONS CONSIDERATIONS ................................................................................................ 9 RADIATED EMISSIONS CONSIDERATIONS .................................................................................................... 9 MEASUREMENT INSTRUMENTATION ............................................................................................................ 10 RECEIVER SYSTEM ............................................................................................................................................ 10 INSTRUMENT CONTROL COMPUTER ............................................................................................................ 10 LINE IMPEDANCE STABILIZATION NETWORK (LISN) ............................................................................... 10 FILTERS/ATTENUATORS .................................................................................................................................. 11 ANTENNAS…

Text truncated - open the document above for the full version.