QDJ-0308LUG001Portable PCS GSM Transceiver

APPLICANT: Chi Mei Communications Systems, Inc. FCC ID: QDJ-0308LUG001 INSTRUCTION MANUAL A preliminary draft copy of the Users Manual follows. EXHIBIT 8 GSM/GPRS SmartPhone User Guide Copyright Statement Copyright 2003 by this company. All rights reserved. No part of this publication may be reproduced, transmitted, transcribed, stored in a retrieval system or translated into any language or computer lan- guage, in any form or by any means, electronic, mechanical, magnetic, optical, chemical, manual or otherwise, without the prior written permission of this company. Disclaimer This company makes no representations or warranties, either expressed or implied, with respect to the contents hereof and specifically disclaims any warranties, merchantability or fitness for any particular purpose. Further, this company reserves the right to revise this publication and to make changes from time to time in the contents hereof without obligation of this company to notify any person of such revision or changes. ALL INFORMATION IS PROVIDED BY THIS COMPANY ON AN "AS IS" BASIS ONLY. THIS COMPANY PROVIDES NO REPRESENTATIONS AND WARRANTIES, EXPRESS OR IMPLIED, INCLUDING THE IMPLIED WARRANTIES OF FITNESS FOR A PARTICULAR PURPOSE, MERCHANTABILITY AND NONINFRINGEMENT. Important Safety Precautions When using this product, the safety precautions below must be taken against possible legal issues and damages. SAFETY IN AIRCRAFT The interference would be caused by this product to an aircraft's navigation system and its network. In most countries, using this product on board an airplane is against the law. SAFETY FOR ENVIRONMENTS Do not use this product in gas stations. Also the use of this product is prohibited in fuel storehouse, chemical plants and locations containing explosives. SAFETY ON THE ROAD Vehicle drivers in motion are not permitted to use telephony services with the handheld device, except in the case of emergency. In some countries, using hand- free devices as an alternative is allowed. SAFETY ABOUT RADIATION This product should be operated in the suggested normal condition only to ensure the radiative performance and safety of the interference. SAFETY FOR MEDICAL EQUIPMENT This product may cause malfunctions of medical equipment. In most hospital or medical centers, use of this product is forbidden. Attention CAUTION RISK OF EXPLOSION IF BATTERY IS REPLACED BY AN INCORRECT TYPE. DISPOSE OF USED BATTERIES ACCORDING TO THE INSTRUCTIONS Tips When Using • Avoid using the product near metal structures (for example, large metal furniture or steel frames of a building). The transmission and reception of signal can be effected by these objects. • Avoid using the product near strong electromagnetic sources, such as microwave ovens, sound speakers, TV and radio. • Avoid using the product right after dramatic change of temperature. There are no user serviceable parts inside this product. If this product appears to be broken, call a qualified service personnel or send this product to your original dealer. Do not attempt to disassemble or repair this product as it may result in electric shock or unrecoverable damage to the product itself. Keep this product out of reach of small children. Store this product in its protective case in a cool dry place. Do not throw the battery into fire or other heat source. Dispose of used batteries according to your local regulations. FCC Compliance Statement This device complies with Part 15 of the FCC Rules. Operation is subject to the following two condi- tions: (1) this device may not cause harmful interference, and (2) this device must accept any interfer- ence received, including interference that may cause undesired operation. FCC ID: QDJ-0308LUG001 Statement according to FCC part 15.21 Modifications not expressly approved bythis company could void the user's authority to operate the equipment. Statement according to FCC part 15.105 NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protec- tion against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: • Reorient or relocate the receiving antenna. • Increase the separation between the equipment and receiver. • Connect the equipment into an outlet on a circuit different from that to which the receiveris con- nected. • Consult the dealer or an experienced radio/TV technician for help. RF exposure Tests for SAR are conducted using standard operating positions specified by the FCC with the phone transmitting at its highest certified power level in all tested frequency bands. Although the SAR is determined at the highest certified power level, the actual SAR level of the phone while operation can be well below the maximum value. This is because the phone is designed to operate at multiple power levels so as to use only the power required to reach the network. In general, the closer you are to a wireless base station antenna, the lower the power output. Before a phone model is available for sale to the public, it must be tested and certified to the FCC that it does not exceed the limit established by the government-adopted requirement for safe exposure. The tests are performed in positions and locations (e.g., at the ear and worn on the body) as required by the FCC for each model. (Body-worn measurements may differ among phone models, depending upon available accessor…

Text truncated - open the document above for the full version.

APPLICANT: Chi Mei Communications Systems, Inc. FCC ID: QDJ-0308LUG001 ATTESTATION STATEMENTS Transceiver type QDJ-0308LUG001 has been tested in accordance with the requirements contained in the appropriate Commission regulations. To the best of my knowledge, these tests were performed using measurement procedures consistent with industry or Commission standards and demonstrate that this equipment complies with the appropriate standards. Each unit manufactured imported or marketed, will conform to the sample tested within the variations that can be expected due to quantity production and testing on a statistical basis. I further certify that the necessary measurements were made at Motorola, located at 600 North U.S. Highway 45, Libertyville, IL. NAME: Andrew Bachler TITLE: Principal Staff Engineer PERSONAL COMMUNICATIONS SECTOR Date: 9/10/03 Page 1 of 2 EXHIBIT 2 APPLICANT: Chi Mei Communications Systems, Inc. FCC ID: QDJ-0308LUG001 I hereby certify that the above application was prepared under my direction and that to the best of my knowledge and belief, the facts set forth in this application and accompanying technical data are true and correct. The technical data supplied with this application was taken under my supervision and is hereby duly certified. I also certify that this transmit equipment (FCC ID: QDJ-0308LUG001) is in compliance with all applicable parts of the FCC Rules. NAME: Andrew Bachler TITLE: PRINCIPAL STAFF ENGINEER. PERSONAL COMMUNICATIONS SECTOR Date: 9/10/03 Page 2 of 2 EXHIBIT 2

Date: September 18, 2003 Subject: Request for additional information regarding FCC ID: QDJ-0308LUG001 Reference: Application Received: 9/8/2003 Correspondence Reference Number: 230917A.QDJ Confirmation Number: TC3230 Date of Original Email: 9/17/2003 Prepared by: Andrew Bachler, Principal Staff Engineer Motorola Personal Communications Sector Libertyville, Illinois 1. What analyzer settings (i.e., RBW, VBW, detector function) were used to make spurious conducted emission measurements? Response: Please refer to Instrument Settings in the revised test report. 2. What analyzer settings (i.e., RBW, VBW, detector function) were used to make spurious radiated emission measurements? Response: Please refer to Instrument Settings in the revised test report. 3. Please correct the 2 typos on p. 4 of the SAR report with the Cal Due Date for the Network Analyzer. Response: Please refer to the supplemental SAR report. 4. It appears that different tissue parameter values are used in the validation tests and in the SAR tests taken the same day. Please explain. Response: Please refer to the supplemental SAR report. 5. The z-axis plot for the dipole validation test taken on 9/2/03 appears to be for 10-g SAR. Please submit the 1-g z-axis plot. Response: Please refer to the supplemental SAR report. 1

APPLICANT: Chi Mei Communications Systems, Inc. FCC ID: QDJ-0308LUG001 September 10, 2003 CONFIDENTIALITY REQUEST CONTAINED WITHIN Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, Maryland 21046 Re: Application for Cellular/PCS Transceiver Certification Gentlemen: Application: Acting as an agent for Chi Mei Communications Systems, Inc.; Motorola, Inc., Personal Communications Sector, 600 N. U.S. Highway 45, Libertyville, Illinois 60048-1286 herein submits: Application for Equipment Authorization for Certification of Cellular Transceiver, FCC ID: QDJ-0308LUG001. Confidentiality: Pursuant to Section 0.459 of the Commission's rules (CFR 47), Motorola requests confidentiality for portions of the material contained in this application and that the identified material be withheld from public inspection following the grant of this authorization. This material contains Motorola's trade secrets and confidential information that Motorola does not customarily release to the public and which is otherwise not generally available to the public. Confidentiality is requested for the following exhibits: • Exhibit 4 Block Diagrams • Exhibit 5 Schematics • Exhibit 10 Parts List • Exhibit 12 Operational Description Description: This equipment is a GSM portable transceiver, which operates in the 1900 MHz PCS bands. Note: This device contains 1800 MHz GSM functions that are not operational in U.S. Territories. This filing is only applicable for 1900 MHz PCS operations. Operation in the 850/900 bands is disabled. Contact Information: Please contact me by telephone at (847) 523-6167,or by e-mail ( [email protected]), if there are questions or additional information needed concerning this filing. Regards, Andrew J. Bachler FCC Liaison Cellular Subscriber Sector 600 N. U.S. Highway 45 Libertyville, IL 60048-5343 Exhibit 13

EXHIBIT 3 Front View Flip Opened Front View Rear ViewRear View (Battey Removed) Showing ID Label APPLICANT: Chi Mei Communications Systems, Inc. FCC ID: QDJ-0308LUG001

APPLICANT: Chi Mei Communications Systems, Inc. FCC ID: QDJ-0308LUG001 FCC IDENTIFICATION (NAMEPLATE) INFORMATION FCC ID: QDJ-0308LUG001 . The FCC label shown is representative of the label that will appear on the radio when in production. It will be placed on the radio telephone as shown in Exhibit 3. Other information may also be included on this label. Exhibit 1

EXHIBIT 9 APPLICANT: Chi Mei Communications Systems, Inc. FCC ID: QDJ-0308LUG001 Front View (shield removed) Rear View (shield removed)

APPLICANT: Chi Mei Communications Systems, Inc. FCC ID: QDJ-0308LUG001 TRANSCEIVER ADJUSTMENTS/TUNE-UP PROCEDURE There are no user accessible adjustments or tuning in this portable cellular transceiver. All necessary adjustments and tuning are performed during manufacture of the product. Any adjustments or tuning after service or repair are done as part of that process, as special equipment is required to perform such adjustments. EXHIBIT 10 Confidential 1(1) 14 August 2003 LIST OF MAIN CIRCUIT DEVICES, THEIR SYMBOLS AND FUNCTIONS FCC IC: QDJ-0308LUG01 Table 1:Main devices on Base Band Section Reference Application Frequency BASE BAND U8 IC, PERSEUS1 120MHZ U131 IC, NAUSICA 13MHZ MEMORY U82 SDRAM 60MHZ IC1 FLASH AUDIO U152 CODEC 11.2896MHZ Table 2:Main devices on RF Module Section Reference Application Frequency RF U704 POWER AMP. 1710~1910 MHZ RF U712 Transceiver 1710 1990 MHZ RF U1802 TCXO 13MHz

APPLICANT: Chi Mei Communication Systems, Inc. FCC ID: QDJ-0308LUG001 E E x x h h i i b b i i t t 1 1 1 1 P P a a g g e e 1 1 Exhibit 11: SAR Test Report QDJ-0308LUG001 Date of test: Date of Report: 08/12/2003-09/03/2003 09/04/2003 Test Laboratory: Motorola Personal Communications Sector Product Safety & Compliance Laboratory 600 N. US Highway 45 Room: MW113 Libertyville, Illinois 60048 Test Responsible: Firass Badaruzzaman Senior RF Engineer Accreditation: This laboratory is accredited to ISO/IEC 17025-1999 to perform the following tests: Tests : Procedures: Electromagnetic Specific Absorption Rate ANSI/IEEE C95.1-1992, 1999 (SAR) IEEE C95.3-1991 IEEE P1528 (DRAFT) FCC OET Bulletin 65 (including Supplements A, B, C) Australian Communications Authority Radio Communications (Electromagnetic Radiation – Human Exposure) Standard 1999 CENELEC EN 50361 (2001) Simulated Tissue Preparation APP-0247 RF Power Measurement DOI-0876, 0900, 0902, 0904, 0915 On the following products or types of products: Wireless Communications Devices (Examples): Two Way Radios; Portable Phones (including Cellular, Licensed Non-Broadcast and PCS); Low Frequency Readers; and Pagers A2LA certificate #1651-01 Statement of Compliance: Motorola declares that portable cellular telephone FCC ID QDJ-0308LUG001 to which this declaration relates, is in conformity with the appropriate General Population/Uncontrolled RF exposure standards, recommendations and guidelines (FCC 47 CFR §2.1093). It also declares that the product was tested in accordance with the appropriate measurement standards, guidelines and recommended practices. Any deviations from these standards, guidelines and recommended practices are noted below: (none) ©Motorola, Inc. 2003 This test report shall not be reproduced except in full, without written approval of the laboratory. The results and statements contained herein relate only to the items tested. The names of individuals involved may be mentioned only in connection with the statements or results from this report. Motorola encourages all feedback, both positive and negative, on this test report. APPLICANT: Chi Mei Communication Systems, Inc. FCC ID: QDJ-0308LUG001 E E x x h h i i b b i i t t 1 1 1 1 P P a a g g e e 2 2 Table of Contents 1) Introduction 3 2) Description of the Device Under Test 3 Antenna description 3 Device description 3 3) Test Equipment 3 3.1 Dosimetric system 3 3.2 Additional equipment used 4 4) Electrical parameters of the tissue simulating liquid 4 5) System Accuracy Verification 4 6) Test Results 5 6.1 Head Adjacent Test Results 6 6.2 Body-Worn Test Results 7 References: Appendix 1: SAR distribution comparison for the system accuracy verification 9 Appendix 2: SAR distribution plots for Phantom Head Adjacent Use 10 Appendix 3: SAR distribution plots for Body Worn Configuration 12 Appendix 4. Probe Calibration Certificate 14 Appendix 5. Dipole Characterization Certificate 15 Appendix 6: Measurement Uncertainty Budget 16 Appendix 7. Photographs of the device under test 19 APPLICANT: Chi Mei Communication Systems, Inc. FCC ID: QDJ-0308LUG001 E E x x h h i i b b i i t t 1 1 1 1 P P a a g g e e 3 3 1. Introduction The Motorola Personal Communications Sector Product Safety Laboratory has performed measurements of the maximum potential exposure to the user of portable cellular phone (FCC ID QDJ-0303BEN01). The Specific Absorption Rate (SAR) of this product was measured. The portable cellular phone was tested in accordance with FCC OET Bulletin 65 Supplement C 01-01. 2. Description of the Device Under Test Antenna description Type Internal Location Top Rear of Phone Length 32mm Dimensions Width 7mm Configuration Patch Device description FCC ID Number QDJ-0308LUG001 Serial number 351638-00-00167-8 Mode(s) of Operation GSM 1800 GSM 1900 Modulation Mode(s) GSM GSM Maximum Output Power Setting 30.5dBm 30.8dBm Duty Cycle 1:8 1:8 Transmitting Frequency Rang(s) 1710.2-1784.8MHz 1850.2-1909.8MHz Production Unit or Identical Prototype (47 CFR §2..908) Identical Prototype Device Category Portable RF Exposure Limits General Population / Uncontrolled 3. Test Equipment Used 3.1 Dosimetric System The Motorola Personal Communications Sector Product Safety & Compliance Laboratory utilizes a Dosimetric Assessment System (Dasy3™ v3.1d) manufactured by Schmid & Partner Engineering AG (SPEAG™), of Zurich Switzerland. All the SAR measurements are taken within a shielded enclosure. The overall RSS uncertainty of the measurement system is ±11.7% (K=1) with an expanded uncertainty of ±23.0% (K=2). The measurement uncertainty budget is given in Appendix 6. Per IEEE 1528, this uncertainty budget is applicable to the SAR range of 0.4 W/kg to 10 W/kg. The list of calibrated equipment used for the measurements is shown below. Description Serial Number Cal Due Date DASY3 DAE V1 SN386 / SN434 18-March-04 / 19-Feb-04 E-Field Probe ET3DV6 SN1521 / SN1522 31-July-04 / 21-March-04 Dipole Validation Kit, D1800V2 SN273tr / SN272tr24-Jun-04 S.A.M. Phantom used for 1900MHz TP-1250 APPLICANT: Chi Mei Communication Systems, Inc. FCC ID: QDJ-0308LUG001 E E x x h h i i b b i i t t 1 1 1 1 P P a a g g e e 4 4 3.2 Additional Equipment Description Serial Number Cal Due Date Signal Generator HP8648C 3847A04845 11/5/2004 Power Meter E4419B GB39511086 2/6/2004 Power Sensor #1 - 8481A US37296471 11/5/2003 Power Sensor #2 - 8481A US37296473 11/5/2003 Network Analyzer HP8753ES US39172529 6/18/2003 Dielectric Probe Kit HP85070B US33020235 Description Serial Number Cal Due Date Signal Generator HP8648C 3847A04822 2/6/2005 Power Meter E4419B GB39511087 2/6/2004 Power Sensor #1 - 8481A US39210929 2/6/2004 Power Sensor #2 - 8481A US39210933 2/6/2004 Network Analyzer HP8753ES US39172529 6/18/2003 Dielectric Probe Kit HP85070B US33020235 4. Electrical parameters of the tissue simulating liquid Prior to conducting SAR measurements, the relative permittivity, ε r , and the conductivity, σ, of the tissue simulating liquids were measured with the HP85…

Text truncated - open the document above for the full version.

September 18, 2003 Supplement to SAR Test Report for Motorola portable cellular phone (FCC ID QDJ- 0308LUG001) Prepared by: Firass Badaruzzaman Motorola Personal Communications Sector Product Safety Laboratory Libertyville, Illinois Summary of FCC request for additional information There was a request for additional information regarding Motorola’s SAR Test Report for Motorola portable cellular phone (FCC ID QDJ-0308LUG001) . The requested information is addressed below in the same numbering sequence received. 3. Please correct the 2 typos on p. 4 of the SAR report with the Cal Due Date for the Network Analyzer. Response: Please look at the below updated table for test equipment: Description Serial Number Cal Due Date Signal Generator HP8648C 3847A04822 2/6/2005 Power Meter E4419B GB39511087 2/6/2004 Power Sensor #1 - 8481A US39210929 2/6/2004 Power Sensor #2 - 8481A US39210933 2/6/2004 Network Analyzer HP8753ES US39172529 6/18/2004 Dielectric Probe Kit HP85070B US33020235 4. It appears that different tissue parameter values are used in the validation tests and in the SAR tests taken the same day. Please explain. Response: The dielectric parameters used for the daily system validation are shown in the table on page 5 of the SAR report (and the plots on pages 9). These values used for the daily system validation are slightly different than those used for the head measurements because they are physically a different setup of tissue stimulant. The 1800MHZ system accuracy verification of the DASY3 was performed using the measurement equipment listed in Section 3. The dipole was placed below a “flat” phantom. This “flat” phantom is made out of 1” thick natural High Density Polyethylene with a thickness at the bottom equal to 2.0mm. It measures 52.7cm(long) x 26.7cm(wide) x 21.2cm(tall). The measured dielectric constant of the material used is less than 2.3 and the loss tangent is less than 0.0046 all the way up to 2.184GHz. 5. The z-axis plot for the dipole validation test taken on 9/2/03 appears to be for 10-g SAR. Please submit the 1-g z-axis plot. Response: The z-axis plots taken from the DASY scans cannot show 1-g or 10-g SAR since the probe is only at a certain location in the simulate inside the phantom and is retracting upward to verify depth of the penetration. Therefore when you select the zaxis plot it only shows the exponential decay curve with respect to the z-axis and no SAR values are generated.

APPLICANT: Chi Mei Communications Systems, Inc. FCC ID: QDJ-0308LUG001 PERSONAL COMMUNICATIONS SECTOR PRODUCT SAFETY AND COMPLIANCE EMC LABORATORY EMC TEST REPORT Test Report Number – 11714-1 Report Date – August 28, 2003 The test results contained herein relate only to the model(s) identified. It is the manufacturer’s responsibility to assure that additional production units of this model are manufactured with identical electrical and mechanical characteristics. As the responsible EMC Engineer, I hereby declare that the equipment tested as specified in this report conforms to the requirements indicated . Signature Name: _Michael E. Hill Title: Senior Electrical Engineer Date : _ 2003-08-28____ This report must not be reproduced, except in full, without written approval from this laboratory. THIS REPORT MUST NOT BE USED TO CLAIM PRODUCT ENDORSEMENT BY A2LA OR ANY AGENCY OF THE U.S. GOVERNMENT. EXHIBIT 6 A2LA Certificate Number: 1846-01 APPLICANT: Chi Mei Communications Systems, Inc. FCC ID: QDJ-0308LUG001 Table of Contents Description Page Test Report Details 4 Applicable Standards 4 Summary of Testing 5 General and Special Conditions 5 Equipment and Cable Configurations 6 Measuring Equipment and Calibration Information 6 Measurement Procedures and Data RF Power Output 7 Radiated Power (ERP) 8 Occupied Bandwidth 9 GSM 1900 Occupied Band Plot 10 GSM 1900 Reference Plot 10 GSM 1900 Lower Band Edge 11 GSM 1900 Upper Band Edge 11 GSM 1900 A Min Block Edge 12 GSM 1900 A Max Block Edge 12 GSM 1900 B Min. Block Edge 13 GSM 1900 B Max Block Edge 13 GSM 1900 C, C2, C3 Min. Block Edge 14 GSM 1900 C Max Block Edge 14 GSM 1900 C1 Min Block Edge 15 GSM 1900 C1 Max Block Edge 15 GSM 1900 C3 Max Block Edge 16 GSM 1900 C4 Max/C5 Min Block Edge 16 GSM 1900 C4 Max Block Edge 17 GSM1900 C5 Min Block Edge 17 GSM 1900 C5 Max Block Edge 18 GSM 1900 D Min. Block Edge 18 GSM 1900 D Max Block Edge 19 GSM 1900 E Min. Block Edge 19 GSM 1900 E Max Block Edge 20 GSM 1900 F Min. Block Edge 20 GSM 1900 F Max Block Edge 21 Spurious Emissions at Antenna Terminals 22 GSM 1900 Tabular and Graphical Data 23 Field Strength of Spurious Emissions 24 GSM 1900 Tabular and Graphical Data 25 Frequency Stability 26 GSM 1900 Tabular and Graphical Data 27 Test Report Number: 11714-1 EXHIBIT 6 2 APPLICANT: Chi Mei Communications Systems, Inc. FCC ID: QDJ-0308LUG001 Field Strength of Spurious Emissions From Unintentional Radiators 28 GSM 1900 Tabular and Graphical Data 29 Appendix A - Radiated Emissions Test Setup Photos Figure A.1 – Radiated Emissions Measurement 30 Figure A.2 – Substitution Measurement 30 Test Report Number: 11714-1 EXHIBIT 6 3 APPLICANT: Chi Mei Communications Systems, Inc. FCC ID: QDJ-0308LUG001 Test Report Details Tests Performed By: Motorola Personal Communications Sector Product Safety and Compliance Group 600 North US Hwy 45 Libertyville, IL 60048 PH (847) 523-6167 Fax (847) 523-4538 Motorola PCS FRN: 0004321311 FCC Registration Number: 316588 Industry Canada Number: IC3908 Tests Requested By: Motorola Inc. Personal Communications Sector 600 North US Hwy 45 Libertyville, IL 60048 Product Type: Cellular Phone Signaling Capability: GSM 1900 Model Number: SUG3561AA Serial Numbers: 330005171, 330005174, 330005207 Testing Complete Date: August 27, 2003 Applicable Standards All tests and measurements indicated in this document were performed in accordance with the Code of Federal Regulations Title 47 Part 2, Sub-part J as well as the following parts: X Part 15 Subpart B – Unintentional Radiators Part 22 Subpart H - Public Mobile Services X Part 24 - Personal Communications Services Part 90 - Private Land Mobile Radio Service Applicable Standards: TIA EIA 137-A, TIA EIA 98-C, ANSI 63.4 2001, RSS-118 (AMPS), RSS-128 (TDMA), RSS-129 (CDMA), RSS-133 (PCS) Test Report Number: 11714-1 EXHIBIT 6 4 APPLICANT: Chi Mei Communications Systems, Inc. FCC ID: QDJ-0308LUG001 Summary of Testing Test Test Name # Pass/Fail 1 RF Power Output NA 2 ERP (Effective Radiated Power) NA 3 Modulation Characteristics Pass 4 Occupied Bandwidth Pass 5 Spurious Emissions at Antenna Terminal Pass 6 Field Strength of Spurious Emissions Pass 7 Frequency Stability Pass 8 Field Strength of Spurious Emissions Pass from Unintentional Radiators Test Test Name Margin with respect # to the Limit_________ 1 RF Power Output NA 2 ERP (Effective Radiated Power) NA 3 Modulation Characteristics NA 4 Occupied Bandwidth See Plots 5 Spurious Emissions at Antenna Terminal 31.9 dB 6 Field Strength of Spurious Emissions 4.7 dB 7 Frequency Stability 24.75 Hz 8 Field Strength of Spurious Emissions 3.3 dB from Unintentional Radiators The margin with respect to the limit is the minimum margin for all modes and bands. ( ) indicates the margin at which the product exceeds the limit. General and Special Conditions The EUT was tested using a fully charged battery when applicable. Where a battery could not be used due to the need for a controlled variation of input voltage, an external power supply was utilized. All testing was done in an indoor controlled environment with an average temperature of 22º C and relative humidity of 50%. Test Report Number: 11714-1 EXHIBIT 6 5 APPLICANT: Chi Mei Communications Systems, Inc. FCC ID: QDJ-0308LUG001 Equipment and Cable Configurations The EUT was tested in a stand-alone configuration that is representative of typical use. Measuring Equipment and Calibration Information ETSDRG Horn Antenna311562229/30/2003 A.H. Systems Inc.DRG Horn AntennaSAS-200/5712654/29/2004 ETSLog-Periodic Antenna314811894/29/2004 ETSBiconical Antenna3110B33694/29/2004 ETSBiconical Antenna3110B337010/25/2003 AttenuatorWeinschel AS-6667510/3/2003 AttenuatorWeinschel AS-6667710/3/2003 Rohde & SchwarzMobile Test SetCMD 80DE29008N/A Hewlett Packard Signal Generator 83623B 3844A01195 5/20/2004 ThermotronEnvironmental ChamberS-43158012/19/2003 Hewlett PackardPre-Amplifier8347A Hewlett PackardPre-Amplifier8447F2805A034195/19/2004 AgilentPower MeterEE4418B11/26/2003 Agile…

Text truncated - open the document above for the full version.

APPLICANT: Chi Mei Communications Systems, Inc. FCC ID: QDJ-0308LUG001 PERSONAL COMMUNICATIONS SECTOR PRODUCT SAFETY AND COMPLIANCE EMC LABORATORY EMC TEST REPORT Test Report Number – 11714-1 Report Date – August 28, 2003 Report Revised – September 18, 2003 per CRN230917A.QDJ The test results contained herein relate only to the model(s) identified. It is the manufacturer’s responsibility to assure that additional production units of this model are manufactured with identical electrical and mechanical characteristics. As the responsible EMC Engineer, I hereby declare that the equipment tested as specified in this report conforms to the requirements indicated . Signature Name: _Michael E. Hill Title: Senior Electrical Engineer Date : _ 2003-08-28____ This report must not be reproduced, except in full, without written approval from this laboratory. THIS REPORT MUST NOT BE USED TO CLAIM PRODUCT ENDORSEMENT BY A2LA OR ANY AGENCY OF THE U.S. GOVERNMENT. A2LA Certificate Number: 1846-01 EXHIBIT 6 APPLICANT: Chi Mei Communications Systems, Inc. FCC ID: QDJ-0308LUG001 Table of Contents Description Page Test Report Details 4 Applicable Standards 4 Summary of Testing 5 General and Special Conditions 5 Equipment and Cable Configurations 6 Measuring Equipment and Calibration Information 6 Measurement Procedures and Data RF Power Output 7 Radiated Power (ERP) 8 Occupied Bandwidth 9 GSM 1900 Occupied Band Plot 10 GSM 1900 Reference Plot 10 GSM 1900 Lower Band Edge 11 GSM 1900 Upper Band Edge 11 GSM 1900 A Min Block Edge 12 GSM 1900 A Max Block Edge 12 GSM 1900 B Min. Block Edge 13 GSM 1900 B Max Block Edge 13 GSM 1900 C, C2, C3 Min. Block Edge 14 GSM 1900 C Max Block Edge 14 GSM 1900 C1 Min Block Edge 15 GSM 1900 C1 Max Block Edge 15 GSM 1900 C3 Max Block Edge 16 GSM 1900 C4 Max/C5 Min Block Edge 16 GSM 1900 C4 Max Block Edge 17 GSM1900 C5 Min Block Edge 17 GSM 1900 C5 Max Block Edge 18 GSM 1900 D Min. Block Edge 18 GSM 1900 D Max Block Edge 19 GSM 1900 E Min. Block Edge 19 GSM 1900 E Max Block Edge 20 GSM 1900 F Min. Block Edge 20 GSM 1900 F Max Block Edge 21 Spurious Emissions at Antenna Terminals 22 GSM 1900 Tabular and Graphical Data 23 Field Strength of Spurious Emissions 24 GSM 1900 Tabular and Graphical Data 25 Frequency Stability 26 GSM 1900 Tabular and Graphical Data 27 Test Report Number: 11714-1 EXHIBIT 6 2 APPLICANT: Chi Mei Communications Systems, Inc. FCC ID: QDJ-0308LUG001 Field Strength of Spurious Emissions From Unintentional Radiators 28 GSM 1900 Tabular and Graphical Data 29 Appendix A - Radiated Emissions Test Setup Photos Figure A.1 – Radiated Emissions Measurement 30 Figure A.2 – Substitution Measurement 30 Test Report Number: 11714-1 EXHIBIT 6 3 APPLICANT: Chi Mei Communications Systems, Inc. FCC ID: QDJ-0308LUG001 Test Report Details Tests Performed By: Motorola Personal Communications Sector Product Safety and Compliance Group 600 North US Hwy 45 Libertyville, IL 60048 PH (847) 523-6167 Fax (847) 523-4538 Motorola PCS FRN: 0004321311 FCC Registration Number: 316588 Industry Canada Number: IC3908 Tests Requested By: Motorola Inc. Personal Communications Sector 600 North US Hwy 45 Libertyville, IL 60048 Product Type: Cellular Phone Signaling Capability: GSM 1900 Model Number: SUG3561AA Ser…

Text truncated - open the document above for the full version.