QEA-10372-2G4TTurbo Strike RC Racer

(Not included) (Not included)   CONTROLLER BATTERY INSTALLATIONCONTROLLER FUNCTIONSVEHICLE BATTERY INSTALLATION IMPORTANT: Keep these instructions. DO NOT DISCARD. Caution: Please read these carefully before using: 1. Only adults should install and replace batteries. 2. Rechargeable batteries are only to be charged under adult supervision 3. Rechargeable batteries are to be removed from the toy before being charged. 4. Non-rechargeable batteries are not to be recharged. 5. If the device is not used for a long time, remove the batteries. 6. Do not mix old and new batteries. 7. Do not mix alkaline, standard (carbon zinc) or rechargeable batteries. 8. Exhausted batteries are to be removed from the toy. 9. The supply terminals are not to be short-circuited. 10. Only batteries of the same or equivalent type as recommended are to be used. 11. Batteries are to be inserted with the correct polarity. 12. Do not dispose of batteries in fire, batteries may explode or leak. 13. Batteries may explode or leak if misused. Warning: Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: • Reorient or relocate the receiving antenna. • Increase the separation between the equipment and receiver. • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. • Consult the dealer or an experienced radio/T V technician for help. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. The packaging must be retained since it contains important information. 1-800-816-1135 | Visit our website! www.kidgalaxy.com Conforms to the safety requirements of ASTM F963 and FCC regulations. Product and colors may vary from items shown. Contains 1 vehicle. MADE IN CHINA ©2026 Kid Galax y, Inc. All Rights Reserved. Kid Galax y, Inc. 150 Dow St. Manchester , NH 03101 USA Item #10372 1. Open the battery compartment on the back of the controller using a screwdriver. 2. Insert 2 × 1.5V AA batteries following the polarity markings. (Batteries not included) 3. Replace the battery cover and tighten the screw securely. Forward – Push the left control stick forward Backward – Pull the left control stick backward Turn Left – Push the right control stick left Turn Right – Push the right control stick right 1.Turn the power switch to OFF. 2.Open the battery compartment on the underside of the vehicle using a screwdriver. 3.Insert 4 × 1.5V AA batteries according to the polarity markings. (Batteries not included) 4.Close the battery cover and tighten the screw KG26125S 10372 KG_TURBO STRIKE RC RACER_PKG | V5_202600410 © 2026 Kid Galaxy Limited Confidential for internal use only.

Form: RFT-AMER-TCB-OP-19o Revision: 1 Page 1 of 1 Date: 1/25/2023 KID GALAXY INC. Attention: Application Examiner Re: Certification designating a U.S. agent for service of process pursuant to 47 CFR part §2.911(d)(7)of the FCC rules To whom it may concern, This letter is to certify that KID GALAXY INC. (“Applicant”) accepts responsibilities to act as its own agent pursuant to 47 CFR part §2.911(d)(7)of the FCC rules for service of process. I consent to the obligation to accept service of process on behalf of the applicant in regard to the FCC ID designated below. I Irene Ngai HEREBY CERTIFY THAT I am authorized to make the representations above on behalf of the Applicant. I further acknowledge the requirement to maintain an agent extends for no less than one year after the termination of all marketing and importation or the conclusion of and commission-related proceeding involving the equipment and agree to immediately notify the FCC and Intertek if there is any change in the status identified above. Applicant Company Name : KID GALAXY INC. Contact Name : Irene Ngai Address : 150 Dow Street, Tower 2, Unit 425B, Manchester, New Hampshire 3101,U.S.A Telephone No : (800)816-1135 114 Email : [email protected] FCC ID : QEA-10372-2G4T Applicant FRN : 0007127632 Signature: ____________________________________ Date: ______06/04/2026______________________________

Form: RFT-AMER-TCB-OP-19n Revision: 1 Page 1 of 1 Date: 1/25/2023 KID GALAXY INC. Attention: Application Examiner Re: Covered List, located at https://www.fcc.gov/supplychain/coveredlist and 47 CFR parts §2.903 and §2.911(d)(5)(ii) of the FCC rules Applicant: KID GALAXY INC. FCC ID: QEA-10372-2G4T To whom it may concern, KID GALAXY INC. (“Applicant”) certifies that the equipment for which authorization is sought is not “covered” equipment prohibited from receiving an equipment authorization pursuant to 47 CFR part §2.903 of the FCC rules and does not originate directly or indirectly from any company named on the covered list located in the link above or any subsidiary or affiliate thereof. Applicant further certifies that, as of the date of the filing of the application, the Applicant is not identified on the Covered List as an entity producing “covered” equipment and is not a subsidiary or affiliate of any such entity pursuant to 47 CFR part §1.50002 and required by 47 CFR part §2.911(d)(5)(ii) of the FCC rules. Applicant further certifies that no Cybersecurity or anti-virus software produced or provided by Kaspersky Lab, Inc. or any of its successors and assignees, including equipment with integrated Kaspersky Lab, Inc. (or any of its successors and assignees) cybersecurity or anti-virus software is installed in the equipment being certified. I HEREBY CERTIFY THAT I am authorized to make the representations above on behalf of the Applicant and agree to immediately notify Intertek if there is any change in the status identified above. [Signature of authorized Proprietor, Partner or Authorized Officer] [Printed Name]Irene Ngai [Title]President [Company name] KID GALAXY INC. [Date]06/04/2026

KID GALAXY INC. 06/04/2026 Federal Communications Commission 445 12 th Street SW Washington, DC 20554 Subject: Limited Agency Agreement KID GALAXY INC. FCC ID: QEA-10372-2G4T To Whom It May Concern: We, KID GALAXY INC.,hereby authorized Intertek Testing Services to act as our Agent for the purpose of preparing application for FCC ID number QEA-10372-2G4T under all applicable parts of the FCC rules and regulations. The effective date of this limited agency agreement is06/04/2026. The Limited Agency Agreement expires on06/03/2027, unless sooner terminated or extended by written notice to Intertek Testing Services and the Federal Communications Commission. This is to advise that we are in full compliance with the Anti-Drug Abuse Act. The applicant is not subject to a denial of federal benefits pursuant to Section 5301 of the Anti-Drug Act of 1988, 21 U.S.C. 862, and no party to the application is subject to a denial of federal benefits pursuant to that section. If you have any questions or comments, please do not hesitate to contact me. Sincerely, [Signature] [Type Name] Irene Ngai [Type Title] President

1(2) KID GALAXY INC. Attention: Certification reviewer RE: Request for Confidentiality FCC ID: QEA-10372-2G4T To Whom It May Concern: Permanent Confidentiality [Complete this section if permanent confidentiality is requested] Request to withhold permanently from public review certain portions of the application for equipment certification for the referenced FCC identifiers. This request for confidentiality is made pursuant to 47 CFR 0.457(d) and 0.459 of the FCC Rules.In particular, the following sections of the application are to be kept permanently confidential: [Select one or more of items below, as appropriate] Schematics Block Diagrams OperationalDescription Tune-up Procedure Parts List Internal Photos (see note) Users Manual (see note) Note 1: Internal Photos may be held confidential 1) if the circuit board or internal components are not accessible to users. For example, it is acceptable if the circuit board is enclosed in epoxy. 2) Also, it is acceptable if the device is not accessible to the public, for example, a device mounted on the top of a large tower (or in a fenced enclosure) such that it is only serviceable by professional designated technicians under a Non-Disclosure Agreement (NDA). All sales for these devices must be under a NDA restricting the disclosure of the propriety information, including internal photos. Users Manual may be held confidential only when the manual contains proprietary technical information intended for professional technicians obligated under a NDA. All sales and distribution of the user’s manual must be under a NDA that restricts the disclosure of the information. In the application cover letter requesting permanent confidentiality the following additional description and the NDA exhibit is required: 1. Describe in detail how internal photos and/or users manual information are controlled to prevent them from becoming public or disclosed to unauthorized persons. 2. Describe how public access is restricted for products serviceable by professional designated technicians. 3. A statement that all sales of the non-consumer device will be under a NDA to include third party sales and that the final user of the device is subject to the NDA. 4. Provide an example of the NDA between the grantee and a purchaser. The request for confidentiality must Note 2: For scanning receiver, the schematics, block diagrams, operational description, tune-up procedure, parts list and internal photos are always held permanently confidential. Short-term Confidentiality[Complete this section if short-term confidentiality is requested] Request to withhold from public review for a period of [please enter 1 to 180] days from the date of the Grant of Equipment Authorization and prior to marketing, certain portions of the application for equipment certification for the referenced FCC identifiers. This request for confidentiality is made pursuant to 47 CFR 0.457(d) and 0.459 of the FCC Rules. In particular, the following sections of the application are to be kept short-term confidential for a period above from the date of the grant. [Select one or more of items below that are not selected in the list above, as appropriate] Schematics Block diagrams Operational Description Tune-up Procedure Parts List 2(2) Test Setup Photos External Photos Internal Photos Users Manual Rationale for request for confidentiality: We have invested considerable time and materials in research and development to produce the referenced product. Permanent confidentiality:Disclosure of the permanently confidential portions of this application to competitors would not only give them significant competitive advantages in developing similar products, but would also disclose successful implementation of unpublished, leading edge technology developed by us. Short-term confidentiality: Disclosure of the short-term confidential portions of this application during the period of importation and/or distribution would reveal key aspects of proprietary technology to competitors and diminish the value of our investment in research and development. If you have questions or need further information, please contact the undersigned. Sincerely, _________________ [Name of the applicant/grantee contact of FCC] Irene Ngai [Title] President [Date]06/04/2026

Page 1 of 2 EXTERNAL PHOTOS Page 2 of 2

SIZE:38*3mm

Page 1 of 3 INTERNAL PHOTOS Page 2 of 3 Page 3 of 3

1 INTERTEK TESTING SERVICES RF Exposure The equipment under test (EUT) is a controller operating at 2.4G Band. The EUT can be powered by DC 3.0V (2 x 1.5V AA batteries). For more detail information pls. refer to the user manual. Antenna Type: Integral antenna. Antenna Gain: 0dBi. The normal radiated output power (e.i.r.p) is: -19.0dBm (tolerance: +/- 3dB). The normal conducted output power is -19.0dBm (tolerance: +/- 3dB). Modulation Type: GFSK. According to the KDB 447498 V06: The Maximum peak radiated emission for the EUT is 76.8 dBμV/m at 3m in the frequency 2407MHz The EIRP = [(FS*D) ^2 / 30] mW = -18.43dBm which is within the production variation. The Minimum peak radiated emission for the EUT is 74.7 dBμV/m at 3m in the frequency 2477MHz The EIRP = [(FS*D) ^2 / 30] mW = -20.53dBm which is within the production variation. The maximum conducted output power specified is -16.0dBm= 0.025mW The source- based time-averaging conducted output power =0.025mW The SAR Exclusion Threshold Level: = 3.0 * (min. test separation distance, mm) / sqrt(freq. in GHz) = 3.0 * 5 / sqrt (2.477) mW = 9.53 mW Since the source-based time-averaging conducted output power is well below the SAR low threshold level, so the EUT is considered to comply with SAR requirement without testing. FCC ID: QEA-10372-2G4T

Kid Galaxy Inc. TEST REPORT SCOPE OF WORK FCC TESTING– MODEL: 10372 REPORTNUMBER SZHH02200492-001 ISSUE DATE AUGUST 9, 2026 PAGES 32 DOCUMENT CONTROL NUMBER FCC ID 249_C © 2017 INTERTEK Intertek Report No.:SZHH02200492-001 This report is for the exclusive use of Intertek's Client and is provided pursuant to the agreement between Intertek and its Client. Intertek's responsibility and liability are limited to the terms and conditions of the agreement. Intertek assumes no liability to any party, other than to the Client in accordance with the agreement, for any loss, expense or damage occasioned by the use of this report. Only the Client is authorized to permit copying or distribution of this report and then only in its entirety. Any use of the Intertek name or one of its marks for the sale or advertisement of the tested material, product or service must first be approved in writing by Intertek. The observations and test results in this report are relevant only to the sample tested. This report by itself does not imply that the material, product, or service is or has ever been under an Intertek certification program. Intertek Testing Service Shenzhen Ltd. Longhua Branch 101, 201, Building B, No. 308 Wuhe Avenue, Zhangkengjing Community GuanHu Subdistrict, LongHua District, Shenzhen, People’s Republic of China Tel: (86 755) 8601 6288 Fax: (86 755) 8601 6751 Version: 01-November-2017 Page:1 of 32 FCC ID 249_C Test Report Kid Galaxy Inc. Application for Certification FCC ID: QEA-10372-2G4T Turbo Strike RC Racer Model: 10372 2.4GHz Transceiver Report No.: SZHH02200492-001 We hereby certify that the sample of the above item is considered to comply with the requirements of FCC Part 15, Subpart C for Intentional Radiator, mention 47 CFR [10-1-24] Prepared and Checked by: Approved by: Maura Wang Engineer Johnny Wang Project Engineer Date: August 9, 2026 Intertek Report No.:SZHH02200492-001 Version: 01-November-2017 Page:2 of 32 FCC ID 249_C Test Report MEASUREMENT/TECHNICAL REPORT This report concerns (check one:) Original Grant X Class II Change Equipment Type: DXX - Part 15 Low Power Communication Device Transmitter Deferred grant requested per 47 CFR 0.457(d)(1)(ii)? Yes No X If yes, defer until: date Company Name agrees to notify the Commission by: date of the intended date of announcement of the product so that the grant can be issued on that date. Transition Rules Request per 15.37? Yes No X If no, assumed Part 15, Subpart C for intentional radiator − the new 47 CFR [10-1-24 Edition] provision. Report prepared by: Maura Wang Intertek Testing Services Shenzhen Ltd. Longhua Branch 101, 201, Building B, No. 308 Wuhe Avenue, Zhangkengjing Community GuanHu Subdistrict, LongHua District, Shenzhen, People’s Republic of China Tel / Fax: 86-755-86016288/86-755-86016751 Intertek Report No.:SZHH02200492-001 Version: 01-November-2017 Page:3 of 32 FCC ID 249_C Test Report Table of Contents 1.0 Summary of Test Result ..................................................................................... 4 2.0 General Description ............................................................................................ 5 2.1Product Description ............................................................................................. 5 2.2Related Submittal(s) Grants ................................................................................ 5 2.3Test Methodology ................................................................................................ 5 2.4Test Facility ........................................................................................................ 5 3.0System Test Configuration .................................................................................. 6 3.1 Justification ........................................................................................................ 6 3.2EUT Exercising Software ..................................................................................... 6 3.3Special Accessories ............................................................................................ 6 3.4Equipment Modification ....................................................................................... 6 3.5Measurement Uncertainty ................................................................................... 7 3.6Support Equipment List and Description .............................................................. 7 4.0Emission Results ................................................................................................. 8 4.1 Radiated Test Results ........................................................................................ 8 4.1.1Field Strength Calculation ................................................................................. 8 4.1.2Radiated Emission Configuration Photograph ................................................... 9 4.1.3Radiated Emissions .......................................................................................... 9 4.1.4Transmitter Spurious Emissions ..................................................................... 13 5.0Equipment Photographs .................................................................................... 23 6.0Product Labelling ............................................................................................... 23 7.0Technical Specifications .................................................................................... 23 8.0Instruction Manual ............................................................................................. 23 9.0Miscellaneous Information ................................................................................ 24 9.1Bandedge Plot .................................................................................................. 24 9.220dB Bandwidth ................................................................................................ 26 9.3Discussion of Pulse Desensitization ...................…

Text truncated - open the document above for the full version.

Page 1 of 4 RADIATED PHOTOS 9KHz to 30MHz (EUT was placed in the centre of the turntable) Page 2 of 4 30MHz to 1GHz (EUT was placed in the centre of the turntable) Page 3 of 4 1GHz to 18GHz (EUT was placed in the centre of the turntable) Page 4 of 4 18GHz to 25GHz (EUT was placed in the centre of the turntable)