QEZPNS-816DOEM Radio Packet Modem

PNS-816D USER’S MANUAL 2W RPM (RADIO PACKET MODEM) DRAFT (Revised June 27, 2002) PALMNET SYSTEM PNS-816D User’s Manual Draft (Revised: June 27, 2002) WARNING: Output is specified at the antenna terminal of this module. This modular transmitter is only approved for OEM integration into final products that satisfy mobile operating requirements of 2.1091. The final product and its antenna must operate with a minimum separation distance of 25 cm or more from all persons using the antenna with the gain not exceeding 3 dBi to satisfy MPE compliance. Separate approval is required for this module to operate in portable products with respect to 2.1093 of FCC rules. Note: Palmnet has devoted its best effort to make this User’s Manual with accuracy; however information in this manual is subject to change without notice. Contact Info: 5 th ACE Techno Tower II, 197-7 Kuro-Dong, Kugo-Ku, Seoul, Korea Tel: (822) 2634-2574 Fax: (822) 2634-2576 Web-site: www.palmnets.com 1 Centerpointe Dr., Suite 210, La Palma, CA 90623, USA Tel: (714) 228-2211 Fax: (714) 228-2208 Email: [email protected] FCC Compliance Statement This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: 1. this device may not cause harmful interference and 2. this device must accept any interference received, including interference that may cause undesired operation. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital devices, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of more of the following measures: • Reorient or relocate the receiving antenna • Increase the separation between the equipment and receiver • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. • Consult the dealer or an experienced radio/TV technician for help. Warning: Changes or modifications not expressly approved by Palmnet System Co., Ltd. could void the user’s authority to operate the equipment. Industry Canada Compliance Statement IC Class B Compliance This device complies with the Class B limit for radio noise emissions as set out in the interference-causing equipment standard entitled “Digital Apparatus,” ICES-003 of Industry Canada. NOTE: This device complies with ICAN RSS 119, under certification number 4358A-PNS816D. TABLE OF CONTENTS 1. PRODUCT OVERVIEW......................................................................................................................................6 2. DIAGNOSTIC PROGRAM OPERATION........................................................................................................7 3. H/W INSTALLATION GUIDE..........................................................................................................................13 3.1 DIMENSION......................................................................................................................................................13 3.2 ZIF 30 PIN CONNECTOR DRAWING................................................................................................................14 3.3 ZIF 30 PIN CONNECTOR ASSIGNMENT..........................................................................................................15 3.4 POWER SUPPLY..............................................................................................................................................15 3.5 NOTICE TO INTEGRATORS..............................................................................................................................15 3.6 INSTALLATION.................................................................................................................................................16 3.6.1 Mounting...................................................................................................................................16 3.6.2 Interface Cable and Connector ................................................................................................16 3.6.3 Antenna Connection.................................................................................................................16 3.6.4 Antenna Connection Diagram ..................................................................................................17 3.7 LABELING INSTRUCTION.................................................................................................................................17 4. GENERAL SPECFICATIONS.........................................................................................................................18 4.1 GENERAL HARDWARE....................................................................................................................................18 4.2 ENVIRONMENTAL............................................................................................................................................18 4.3 POWER SUPPLY..............................................................................................................................................18 4.4 COMMUNICATION INTERFACES.......................................................................................................................18 4.5 ANTENNA........................................................................................................................................................18 4.6 GEN…

Text truncated - open the document above for the full version.

July 2, 2002 FEDERAL COMMUNICATIONS COMMISSION 7435 Oakland Mills Road Columbia, MD 21046 USA Subject: Type Acceptance Application under FCC 47 CFR, Parts 2 and 90 (Subpart I) - Licensed Non-Broadcast Radio Transceiver Operating in the frequency band 806-825 MHz (25 kHz Channel Spacing) Applicant: Palmnet System Co., Ltd. Product: OEM Radio Packet Modem Model: PNS-816D FCC ID: QEZPNS-816D Dear Sir/Madam, As appointed agent for Palmnet System Co., Ltd., we would like to submit the application to Federal Communications Commission for certification of the above product. Please review all necessary files uploaded to FCC OET site. This application is for Modular Approval with antenna gain equal to or less than 3 dBi for mobile/base and fixed station devices. The antenna(s) used for this transmitter must be installed with a minimum separation distance of 25 cm from all persons during normal operation to satisfy MPE compliance. The above Device complies with FCC Modular Approval Requirements and they are listed below: 1) The module is completed with its own reference oscillator. 2) The only connectors to the module are dc supply, rf and data port 3) The radio complies with MPE per 2.1091 for use with mobile or fixed base stations. 4) The module complies with FCC Part15, Subpart B, Class B – Unintentional radiators. 5) The receiver operating in 851 - 870 MHz complies with FCC Part 15, Subpart B – Radio Receivers. 6) End-users must comply with the instruction stated in the users’ manual: i. Labeling requirements for equipment using this modular transceiver ii. RF Exposure information for compliance with FCC Rules 2.1091 or 2.1093 are specified in the user manual for OEM, integrator and/or end user 7) The transceiver module has its own RF shielding. 8) The transceiver module has buffered modulation/data inputs 9) The transceiver module has its own power supply regulation. 10) The transceiver module was tested in a stand-alone configuration. If you have any queries, please do not hesitate to contact us by our TOLL FREE number: OUR TELEPHONE NO.: 1-877-765-4173 Yours truly, Tri Minh Luu, P. Eng., V.P., Engineering TML/DH Encl. UltraTech Group of La bs 31040/SIT A96/TH/0093 46390-2049 200093-0 2 00-034 3000 Bristol Circle, Oakville, Ontario, Canada L6H 6G4 Telephone (905) 829-1570 Facsimile (905) 829-8050

ANNEX 3 – EXTERNAL EUT PHOTOS PalmNet System Co., Ltd. OEM Radio Packet Modem, Model PNS-816D FCC ID: QEZPNS-816D A3 - 1 ANNEX 3 – EXTERNAL EUT PHOTOS PalmNet System Co., Ltd. OEM Radio Packet Modem, Model PNS-816D FCC ID: QEZPNS-816D A3 - 2 ANNEX 3 – EXTERNAL EUT PHOTOS PalmNet System Co., Ltd. OEM Radio Packet Modem, Model PNS-816D FCC ID: QEZPNS-816D A3 - 3

FCC IDENTIFIER LABELING Location of FCC Label FCC ID LABEL PalmNet System MODEL: PNS-816D FCC ID: QEZPNS-816D IC: 4358A-PNS816D LLI: This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference and (2) this device must accept any interference received, including interference that may cause undesired operation MADE IN KOREA

ANNEX 4 – INTERNAL EUT PHOTOS PalmNet System Co., Ltd. OEM Radio Packet Modem, Model PNS-816D FCC ID: QEZPNS-816D A4 - 1 ANNEX 4 – INTERNAL EUT PHOTOS PalmNet System Co., Ltd. OEM Radio Packet Modem, Model PNS-816D FCC ID: QEZPNS-816D A4 - 2 ANNEX 4 – INTERNAL EUT PHOTOS PalmNet System Co., Ltd. OEM Radio Packet Modem, Model PNS-816D FCC ID: QEZPNS-816D A4 - 3

ANNEX 1 - TEST DATA PLOTS PalmNet System Co., Ltd. OEM Radio Packet Modem, Model PNS-816D FCC ID: QEZPNS-816D A1 - 1 Plot # 1 99% Emission Bandwidth Carrier Frequency: 806.0125 MHz Channel Spacing: 25 kHz Power: 2 W Modulation: FM with 19.2 kbps random data rate ANNEX 1 - TEST DATA PLOTS PalmNet System Co., Ltd. OEM Radio Packet Modem, Model PNS-816D FCC ID: QEZPNS-816D A1 - 2 Plot # 2 99% Emission Bandwidth Carrier Frequency: 815.0875 MHz Channel Spacing: 25 kHz Power: 2 W Modulation: FM with 19.2 kbps random data rate ANNEX 1 - TEST DATA PLOTS PalmNet System Co., Ltd. OEM Radio Packet Modem, Model PNS-816D FCC ID: QEZPNS-816D A1 - 3 Plot # 3 99% Emission Bandwidth Carrier Frequency: 824.9875 MHz Channel Spacing: 25 kHz Power: 2 W Modulation: FM with 19.2 kbps random data rate ANNEX 1 - TEST DATA PLOTS PalmNet System Co., Ltd. OEM Radio Packet Modem, Model PNS-816D FCC ID: QEZPNS-816D A1 - 4 Plot # 4 Emission Mask G Carrier Frequency: 806.0125 MHz Channel Spacing: 25 kHz Power: 2 W Modulation: FM with 19.2 kbps random data rate ANNEX 1 - TEST DATA PLOTS PalmNet System Co., Ltd. OEM Radio Packet Modem, Model PNS-816D FCC ID: QEZPNS-816D A1 - 5 Plot # 5 Emission Mask G Carrier Frequency: 815.0875 MHz Channel Spacing: 25 kHz Power: 2 W Modulation: FM with 19.2 kbps random data rate ANNEX 1 - TEST DATA PLOTS PalmNet System Co., Ltd. OEM Radio Packet Modem, Model PNS-816D FCC ID: QEZPNS-816D A1 - 6 Plot # 6 Emission Mask G Carrier Frequency: 824.9875 MHz Channel Spacing: 25 kHz Power: 2 W Modulation: FM with 19.2 kbps random data rate ANNEX 1 - TEST DATA PLOTS PalmNet System Co., Ltd. OEM Radio Packet Modem, Model PNS-816D FCC ID: QEZPNS-816D A1 - 7 Plot # 7 Spurious Emissions at Antenna Terminals Carrier Frequency: 806.0125 MHz Channel Spacing: 25 kHz Power: 2 W Modulation: FM with 19.2 kbps random data rate ANNEX 1 - TEST DATA PLOTS PalmNet System Co., Ltd. OEM Radio Packet Modem, Model PNS-816D FCC ID: QEZPNS-816D A1 - 8 Plot # 8 Spurious Emissions at Antenna Terminals Carrier Frequency: 806.0125 MHz Channel Spacing: 25 kHz Power: 2 W Modulation: FM with 19.2 kbps random data rate ANNEX 1 - TEST DATA PLOTS PalmNet System Co., Ltd. OEM Radio Packet Modem, Model PNS-816D FCC ID: QEZPNS-816D A1 - 9 Plot # 9 Spurious Emissions at Antenna Terminals Carrier Frequency: 806.0125 MHz Channel Spacing: 25 kHz Power: 2 W Modulation: FM with 19.2 kbps random data rate ANNEX 1 - TEST DATA PLOTS PalmNet System Co., Ltd. OEM Radio Packet Modem, Model PNS-816D FCC ID: QEZPNS-816D A1 - 10 Plot # 10 Spurious Emissions at Antenna Terminals Carrier Frequency: 815.0875 MHz Channel Spacing: 25 kHz Power: 2 W Modulation: FM with 19.2 kbps random data rate ANNEX 1 - TEST DATA PLOTS PalmNet System Co., Ltd. OEM Radio Packet Modem, Model PNS-816D FCC ID: QEZPNS-816D A1 - 11 Plot # 11 Spurious Emissions at Antenna Terminals Carrier Frequency: 815.0875 MHz Channel Spacing: 25 kHz Power: 2 W Modulation: FM with 19.2 kbps random data rate ANNEX 1 - TEST DATA PLOTS PalmNet System Co., Ltd. OEM Radio Packet Modem, Model PNS-816D FCC ID: QEZPNS-816D A1 - 12 Plot # 12 Spurious Emissions at Antenna Terminals Carrier Frequency: 815.0875 MHz Channel Spacing: 25 kHz Power: 2 W Modulation: FM with 19.2 kbps random data rate ANNEX 1 - TEST DATA PLOTS PalmNet System Co., Ltd. OEM Radio Packet Modem, Model PNS-816D FCC ID: QEZPNS-816D A1 - 13 Plot # 13 Spurious Emissions at Antenna Terminals Carrier Frequency: 824.9875 MHz Channel Spacing: 25 kHz Power: 2 W Modulation: FM with 19.2 kbps random data rate ANNEX 1 - TEST DATA PLOTS PalmNet System Co., Ltd. OEM Radio Packet Modem, Model PNS-816D FCC ID: QEZPNS-816D A1 - 14 Plot #14 Spurious Emissions at Antenna Terminals Carrier Frequency: 824.9875 MHz Channel Spacing: 25 kHz Power: 2 W Modulation: FM with 19.2 kbps random data rate ANNEX 1 - TEST DATA PLOTS PalmNet System Co., Ltd. OEM Radio Packet Modem, Model PNS-816D FCC ID: QEZPNS-816D A1 - 15 Plot # 15 Spurious Emissions at Antenna Terminals Carrier Frequency: 824.9875 MHz Channel Spacing: 25 kHz Power: 2 W Modulation: FM with 19.2 kbps random data rate

OEM Radio Packet Modem Model No.: PNS-816D FCC ID: QEZPNS-816D Applicant: Palmnet System Co., Ltd. 5th ACE TECHNO TOWER II, 197-7 Kuro-Dong Kuro-Ku, Seoul South Korea 152-847 Tested in Accordance With Federal Communications Commission (FCC) 47 CFR, PARTS 2 and 90 (Subpart I) UltraTech's File No.: PNS-001F90 This Test report is Issued under the Authority of Tri M. Luu, Professional Engineer, Vice President of Engineering UltraTech Group of Labs Date: July 2, 2002 Report Prepared by: Dan Huynh Tested by: Hung Trinh, RFI/EMI Technician Issued Date: July 2, 2002 Test Dates: May 27-29, 2002 ƒ The results in this Test Report apply only to the sample(s) tested, and the sample tested is randomly selected. ƒ This report must not be used by the client to claim product endorsement by NVLAP or any agency of the US Government. UltraTech 3000 Bristol Circle, Oakville, Ontario, Canada, L6H 6G4 Tel.: (905) 829-1570 Fax.: (905) 829-8050 Website: www.ultratech-labs.com Email: [email protected], Email: [email protected] 2 31040/SIT C-1376 46390-2049 200093-0 00-034 FCC PARTS 2 & 90, SUBPART I, LICENSED NON-BROADCAST RADIO TRANSCEIVERS Contents i OEM Radio Packet Modem, Model PNS-816D FCC ID: QEZPNS-816D ULTRATECH GROUP OF LABS File #: PNS-001F90 3000 Bristol Circle, Oakville, Ontario, Canada L6H 6G4 July 2, 2002 Tel.: 905-829-1570, Fax. : 905-829-8050 All test results contained in this engineering test report are traceable to National Institute of Standards and Technology (NIST) TABLE OF CONTENTS EXHIBIT 1. SUBMITTAL CHECK LIST .................................................................................................................. 1 EXHIBIT 2. INTRODUCTION .................................................................................................................................... 2 2.1. SCOPE........................................................................................................................................................................ 2 2.2. RELATED SUBMITTAL(S)/GRANT(S)............................................................................................................................ 2 2.3. NORMATIVE REFERENCES.......................................................................................................................................... 2 EXHIBIT 3. PERFORMANCE ASSESSMENT .........................................................................................................3 3.1. CLIENT INFORMATION................................................................................................................................................ 3 3.2. EQUIPMENT UNDER TEST (EUT) INFORMATION........................................................................................................... 3 3.3. EUT’S TECHNICAL SPECIFICATIONS............................................................................................................................ 4 3.4. LIST OF EUT’S PORTS.................................................................................................................................................. 4 3.5. ANCILLARY EQUIPMENT............................................................................................................................................ 4 EXHIBIT 4. EUT OPERATING CONDITIONS AND CONFIGURATIONS DURING TESTS .......................... 5 4.1. CLIMATE TEST CONDITIONS....................................................................................................................................... 5 4.2. OPERATIONAL TEST CONDITIONS & ARRANGEMENT FOR TEST SIGNALS.................................................................... 5 EXHIBIT 5. SUMMARY OF TEST RESULTS.......................................................................................................... 6 5.1. LOCATION OF TESTS................................................................................................................................................... 6 5.2. APPLICABILITY & SUMMARY OF EMC EMISSION TEST RESULTS.................................................................................. 6 5.3. MODIFICATIONS INCORPORATED IN THE EUT FOR COMPLIANCE PURPOSES................................................................. 6 EXHIBIT 6. MEASUREMENTS, EXAMINATIONS & TEST DATA FOR EMC EMISSIONS.......................... 7 6.1. TEST PROCEDURES..................................................................................................................................................... 7 6.2. MEASUREMENT UNCERTAINTIES................................................................................................................................7 6.3. MEASUREMENT EQUIPMENT USED.............................................................................................................................. 7 6.4. ESSENTIAL/PRIMARY FUNCTIONS AS DECLARED BY THE MANUFACTURER................................................................. 7 6.5. RF POWER OUTPUT @ FCC 2.1046 & 90.205.............................................................................................................. 8 6.5.1. Limits @ FCC 90.205 ..................................................................................................................................... 8 6.5.2. Method of Measurements ................................................................................................................................ 8 6.5.3. Test Equipment List......................................................................................................................................... 8 6.5.4. Test Arrangement............................................................................................................................................ 8 6.5.5. Test Data......................................................................................................................................................... 8 6.6. RF EXPOSURE…

Text truncated - open the document above for the full version.

ANNEX 2 - TEST SETUP PHOTOGRAPHS (Radiated Emissions at 3 Meters Distance) PalmNet System Co., Ltd. OEM Radio Packet Modem, Model PNS-816D FCC ID: QEZPNS-816D A2 - 1 ANNEX 2 - TEST SETUP PHOTOGRAPHS (Radiated Emissions at 3 Meters Distance) PalmNet System Co., Ltd. OEM Radio Packet Modem, Model PNS-816D FCC ID: QEZPNS-816D A2 - 2 ANNEX 2 - TEST SETUP PHOTOGRAPHS (Radiated Emissions at 3 Meters Distance) PalmNet System Co., Ltd. OEM Radio Packet Modem, Model PNS-816D FCC ID: QEZPNS-816D A2 - 3 ANNEX 2 - TEST SETUP PHOTOGRAPHS (Radiated Emissions at 3 Meters Distance) PalmNet System Co., Ltd. OEM Radio Packet Modem, Model PNS-816D FCC ID: QEZPNS-816D A2 - 4