QH67115952RV2Turn signal light remote unit

Federal Communications Commission Authorization and Evaluation Division Confidentiality Request regarding application for certification of FCC ID: QH67115952RV2. Pursuant to Sections 0.457 and 0.459 of the Commission’s Rules, we hereby request confidential treatment of information accompanying this application as outlined below: Exhibit Type File Name Block Diagram QH67115952RV2 BlkDia.pdf Operational Description QH67115952RV2 OpDes.pdf Schematics QH67115952RV2 Schem.pdf The above materials contain trade secrets and proprietary information not customarily released to the public. The public disclosure of these materials may be harmful to the applicant and provide unjustified benefits to its competitors. The applicant understands that pursuant to Section 0.457 of the Rules, disclosure of this application and all accompanying documentation will not be made before the date of the Grant for this application. Sincerely, Bell Sports Inc. Kyle Bretting QC Engineer

17 May 21 Equipment Authorization Division Office id Engineering and Technology Federal Communications Commission 7435 Oakland Mills Road Columbia, MD 21046 Dear Sirs: Bell Sports Inc. requests acceptance of the labeling proposal described below for Turn signal light remote unit bearing FCC identifier FCC ID: QH67115952RV2. The subject Turn signal light remote unit models as shown in figure 1, authorized under FCC Part 15 Subpart C figure 1 Insert the external photo of the product with its size It is because the surface of the device does not enough to indicate the FCC statement. For this reason, Bell Sports Inc. proposes those statements is showing on the user manual and the device is carrying the FCC ID number only. The figure2 is showing the FCC ID location. figure 2 Sincerely, Bell Sports Inc. ------------------------------- Bell Sports Inc. Kyle Bretting QC Engineer Insert the photo of FCC ID location

C:\Users\Ken Leung\Desktop\Job\LY021855 J00788401 Bell sport\New\remote\POA_Letter_140225_CMA (remote).docx Date: 17 May 21 SUBJECT: FCC Application for FCC ID: QH67115952RV2 To Whom It May Concern: We, the undersigned, hereby authorize CMA Industrial Development Foundations Limited (Andrew Wong) on our behalf, to apply to the Federal Communications Commission on our equipment. Any and all acts carried out by CMA Industrial Development Foundation Limited (Andrew Wong) on our behalf shall have the same effect as acts of our own. This is to advise that we are in full compliance with the Anti- Drug Abuse Act. We, the Bell Sports Inc., are not subject to a denial of federal benefits pursuant to Section 5301 of the Anti-Drug Act of 1988, 21 USC853a, and no party to the application is subject to a denial of federal benefits pursuant to that section. Regards, Bell Sports Inc. Kyle Bretting QC Engineer

FCC ID: QH67115952RV2 External Photo FCC ID: QH67115952RV2

FCC ID: QH67115952RV2 Label Sample

FCC ID: QH67115952RV2 Internal Photo FCC ID: QH67115952RV2 EUT Antenna

RF EXPOSURE EVALUATION Report No. : AA0022304(0) Date: 21 Apr, 2021 For and on behalf of CMA Industrial Development Foundation Limited Authorized Signature : Page 1 of 2 Document name: FCC RF exposure - Document Ref No: RT-EL-EMC-008 - Issue Date: 01 Dec 2017 - Edition: 1 The conformity statement stated in Conclusion above is based on the decision rule agreed with applicant and listed in www.cmatesting.org/qac/statement-of-conformity.pdf. This document is issued subject to the latest CMA Testing General Terms and Conditions of Testing and Inspection Services, available on request or accessible at website www.cmatesting.org. This document shall not be reproduced except in full without written approval by CMA Testing. The results apply to the sample as received unless otherwise specified. The observations and test results in this report are relevant only to the sample tested. CMA Industrial Development Foundation Limited Room 1302, Yan Hing Centre, 9-13 Wong Chuk Yeung St., Fo Tan, Shatin, N.T., Hong Kong. Tel: (852) 2698 8198 Fax: (852) 2695 4177 E-mail: [email protected] Web Site: http://www.cmatesting.org Application No. : LA003560(3) Applicant : Bell Sports Inc. 5550 SCOTTS VALLEY DRIVE, SCOTTS VALLEY, CA 95066 Sample Description : One(1) item of submitted sample stated to be Product Descriptin : Remote of Turn Signal Model : JY-1305A Sample registration No. : RA032368-001 Radio Frequency : 2403 – 2480MHz Supply voltage : DC3V No. of submitted sample : 1 FCC ID : QH67115962RV2 Date Received : 02 Apr 2021 Evaluation Period : 06 Apr 2019 to 19 Apr 2021 Evaluation Method : 447498 D01 General RF Exposure Guidance v06 - RF Exposure Procedure and Equipment Authorization Policies for Mobile and Portable Devices Conclusion : The source-based time-averaged maximum conducted power of Bluetooth operation were satisfied RF exposure requirements. RF EXPOSURE EVALUATION Report No. : AA0022304(0) Date: 21 Apr, 2021 Page 2 of 2 Document name: FCC RF exposure - Document Ref No: RT-EL-EMC-008 - Issue Date: 01 Dec 2017 - Edition: 1 CMA Industrial Development Foundation Limited Room 1302, Yan Hing Centre, 9-13 Wong Chuk Yeung St., Fo Tan, Shatin, N.T., Hong Kong. Tel: (852) 2698 8198 Fax: (852) 2695 4177 E-mail: [email protected] Web Site: http://www.cmatesting.org Simultaneous power No Simultaneuous transmission RF Exposure Evaluation According to KDB 447498 D01 clause 4.3.1 a), transmission from 100 MHz to 6 GHz and test separation distances ≤ 50 mm, the 1-g and 10-g SAR test exclusion thresholds are determined by the following: [(max. power of channel, including tune-up tolerance, mW) / (min. test separation distance, mm)] · [√f(GHz)] Calculation - Frequency : 2.480GHz - Max. peak conducted output power , including tune-up tolerance : 0.17mW - Minimum test separation distances : <5mm where -f(GHz) is the RF channel transmit frequency in GHz. -Power and distance are rounded to the nearest mW and mm before calculation. -The result is rounded to two decimal place for comparison. Substitute above reading for calculation. [(mW) / (mm)] x √GHz] Result = 0.0535 Requirements: ≤ 3.00 for 1-g SAR and ≤ 7.5 for 10-g extremity SAR Conclusion The corresponding SAR test exclusion threshold was satisfied 4.3.1a) requirements. Measurement or numerical simulation is not required. ***** End of Evaluation *****

TEST REPORT Report No. : AA0022303(0) Date : 21 Apr, 2021 For and on behalf of CMA Industrial Development Foundation Limited Authorized Signature : Page 1 of 19 FCC ID: QH67115952RV2 The conformity statement stated in Conclusion above is based on the decision rule agreed with applicant and listed in www.cmatesting.org/qac/statement-of-conformity.pdf. This document is issued subject to the latest CMA Testing General Terms and Conditions of Testing and Inspection Services, available on request or accessible at website www.cmatesting.org. This document shall not be reproduced except in full without written approval by CMA Testing. The results apply to the sample as received unless otherwise specified. The observations and test results in this report are relevant only to the sample tested. CMA Industrial Development Foundation Limited Room 1302, Yan Hing Centre, 9-13 Wong Chuk Yeung St., Fo Tan, Shatin, N.T., Hong Kong. Tel: (852) 2698 8198 Fax: (852) 2695 4177 E-mail: [email protected] Web Site: http://www.cmatesting.org Application No. : LA003560(3) Applicant : Bell Sports Inc. 5550 SCOTTS VALLEY DRIVE, SCOTTS VALLEY, CA 95066 Sample Description : One(1) item of submitted sample stated to be: Sample Description Model No. Remote of Turn Signal JY-1305A Radio Frequency : 2403MHz – 2480MHz Rating : 1 x 3V button cell No. of submitted sample : Two (2) sets Sample registration No. : RA032368-001 Date Received : 02 Apr 2021 Test Period : 06 Apr 2019 to 19 Apr 2021 Test Requested : FCC 47CFR Part 15 Certification Test Method : 47 CFR Part 15 (10-1-19 Edition) ANSI C63.10 – 2013 ANSI C63.4 – 2014 Test Result : See attached sheet(s) from page 2 to 19. Conclusion : The submitted sample was found to comply with requirement of FCC 47CFR Part 15 Subpart C, section 15.249. TEST REPORT Report No. : AA0022303(0) Date : 21 Apr, 2021 Page 2 of 19 FCC ID: QH67115952RV2 CMA Industrial Development Foundation Limited Room 1302, Yan Hing Centre, 9-13 Wong Chuk Yeung St., Fo Tan, Shatin, N.T., Hong Kong. Tel: (852) 2698 8198 Fax: (852) 2695 4177 E-mail: [email protected] Web Site: http://www.cmatesting.org Table of Contents 1 General Information ................................................................................................................................... 3 1.1 General Description ............................................................................................................................ 3 1.2 Location of the test site ....................................................................................................................... 4 1.3 List of measuring equipment............................................................................................................... 5 1.4 Measurement Uncertainty ................................................................................................................... 6 1.5 Test Summary ..................................................................................................................................... 6 2 Description of the radiated emission test ................................................................................................... 7 2.1 Test Procedure .................................................................................................................................... 7 2.2 Test Setup ........................................................................................................................................... 8 2.3 Test Result ........................................................................................................................................ 10 3.1 Test Procedure .................................................................................................................................. 14 3.2 Test Result ........................................................................................................................................ 14 3.3 Test Setup ......................................................................................................................................... 14 3.4 Graph and Table of Conducted Emission Measurement Data .......................................................... 14 4 Supplementary document ......................................................................................................................... 15 4.1 Bandwidth ......................................................................................................................................... 15 5 Appendices ............................................................................................................................................... 16 TEST REPORT Report No. : AA0022303(0) Date : 21 Apr, 2021 Page 3 of 19 FCC ID: QH67115952RV2 CMA Industrial Development Foundation Limited Room 1302, Yan Hing Centre, 9-13 Wong Chuk Yeung St., Fo Tan, Shatin, N.T., Hong Kong. Tel: (852) 2698 8198 Fax: (852) 2695 4177 E-mail: [email protected] Web Site: http://www.cmatesting.org 1 General Information 1.1 General Description The 16MHz crystal oscillator drives the base of IC final amplifier. The modulation provided by IC u1. The output of U1 has the matching network consisting C4, L1 that limit the harmonic content and affect the proper coupling of the antenna to the output stage . Antenna, Ground and Power Source: The antenna consists of PCB antenna with 0.0dBi gain. The ground is only that of the printed circuit board. Electric current is supplied by 1 x 3V button cell. Operation Descriptions: The Equipment Under Test (EUT) is a portable 2.4GHz transmitter, The transmitter is a remote control system. The transmission signal is frequency hopping with channel frequency range 2403.0.- 2480.0MHz during normal use. The EUT was set to fixed frequency test mode by application. The EUT is powered by 1 x 3V button cell. After switching on the EUT, the light can be controlled. The transmitter has three keys to control the light re…

Text truncated - open the document above for the full version.

FCC ID: QH67115952RV2 Test Setup Photo 30MHz – 200MHz 200Mz – 1GHz FCC ID: QH67115952RV2 9kHz – 30MHz Above 1GHz