QL7SSIVTX012.4 GHz Video Transmitter

SEARCHCAM ® ENTRYLINK ® Hazmat Wireless Video System INSTRUCTION MANUAL Model SC-EL-300 800-722-2824 V: 1 – 6/05 661-588-6270 FAX 661-588-6274 EMAIL [email protected] 2 SEARCHCAM ® ENTRYLINK ® INSTRUCTION MANUAL SAFETY PRECAUTIONS Read and follow this manual. Operations in and around a hazardous material release are extremely dangerous. Only those individuals who are specifically trained to operate in a hazardous materials exclusion zone should attempt to use this product within the exclusion zone. There is no substitute for proper training and good judgment. HAZARDOUS ATMOSPHERES Federal law prohibits entry into a flammable atmosphere when the lower explosive level exceeds 10%. The Searchcam ® EntryLink ® is not designed to operate continuously in a flammable atmosphere. It is designed to allow safe exit from a flammable atmosphere if one is encountered during entry operations. Carry and use a direct reading combustible gas indicator where flammable vapors may be present. If flammable vapors are encountered, immediately exit the area and take the necessary steps to change the atmosphere before returning to the area. Do not attempt to charge the EntryLink battery pack in a hazardous atmosphere, as an explosion may result. Only the EntryLink handheld camera unit is approved for hazardous atmospheres. Do not place the receiver system in a hazardous atmosphere. Do not modify the EntryLink. Modifications to the EntryLink may cause an explosion in a hazardous atmosphere. ELECTROCUTION HAZARD The EntryLink antenna stand will conduct electricity. Always check for overhead power lines before raising the antenna stand. Do not place the antenna within 20 feet of any power line or energized equipment. LASER WARNING FCC STATEMENT 3 The Searchcam EntryLink contains a video transmission system that requires a FCC license under Part 90 of the FCC rules. The transmitter operates in the frequency range between 2450 and 2483 MHz. Any modifications to the system may void the user’s authority to operate this system under FCC rules. The FCC ID for the transmitter is: QL7SSIVTX01. BATTERY CAUTION 4 The Searchcam EntryLink is equipped with an internal Lithium Ion battery pack. This battery system is state of the art and is capable of providing long system operation at one half the weight of older battery technologies. Lithium Ion batteries perform well in very cold and very warm temperatures and they do not develop a memory. However, the system requires proper maintenance to achieve full operational life. To assure that the EntryLink continues to operate reliably, follow these simple guidelines. 1. Always recharge the EntryLink after each use. Do not store the system with a discharged battery. Since the EntryLink draws a small amount of current even when shut down, a fully discharged battery would continue to be drawn down and reach a point where it would be damaged. 2. Whenever possible, store the unit with the battery charger plugged into the unit and with power to the battery charger. The battery charger will maintain the Searchcam EntryLink battery at a full charge, thereby assuring the unit is ready for immediate use. 3. If it is not possible to store the EntryLink connected to the battery charger, then the EntryLink battery should be recharged every 30 days to avoid non-recoverable deep discharge. SYSTEM DESCRIPTION The Searchcam® EntryLink is a wireless video camera system designed for entry into hazardous areas. The EntryLink will provide incident commanders with real 5 time video images and audio information from the incident exclusion zone and is specifically designed to safely operate at hazardous material incidents. The EntryLink system consists of four major components; the handheld camera, the receiver antenna, the control receiver console and the video monitor. These four components are required to properly operate the EntryLink system. ENTRYLINK HANDHELD CAMERA The handheld video camera is carried by the entry team into the exclusion zone and houses several subcomponents necessary for system operation. These include the color video camera, the microphone, the illumination system, the air temperature sensor, the digital compass, the laser pointer, the wireless transmitter, the antenna and the battery pack. The protective housing contains these subcomponents and seals and protects them from the harsh environment of the exclusion zone. The EntryLink handheld camera is the business end of the system. RECEIVER ANTENNA MODULE The receiver antenna module consists of two subcomponents; the wireless receiver and the directional high gain antenna. The combination of the pair functions to receive the signal transmitted by the EntryLink transmitter and converts it into signals used to recreate the video and audio. The module is designed to be used in an elevated position and should be placed outdoors, facing the entry team. The portable telescoping antenna stand is the primary method for elevating the antenna up to 17 feet above the ground. However, other mounting systems may be utilized, such as vehicle mounts and permanent towers. The receiver antenna module should be placed as high as possible above the ground. RECEIVER CONTROL CONSOLE The receiver control console provides power and signal processing for the receiver antenna module. The control console is also the point of operation for the receiver side of the system. Power, cable selection, and channel selection are all controlled or monitored from the console. Typically, the control console would be placed on or near the video monitor. VIDEO MONITOR The video monitor is the output of the EntryLink system. The video monitor accepts the video and audio signals from the control console and displays the information gathered by the Entry Team. Any standard video monitor can be used with the EntryLink. Also, a videocassette recorder (VCR) may be used with the monitor to capture and record the video and audio from the EntryLink. SYSTEM SETUP ANTENNA…

Text truncated - open the document above for the full version.

P.O. BOX 80307 · BAKERSFIELD, CA 93380-0307 · 661.588.6270 · 800.722.2824 · FAX 661.588.6274 EMISSION DESIGNATOR The Emission Designator is 11M0F8F. This is derived from maximum modulation frequency of the video signal is 4.5 MHz, the peak deviation of carrier by the video signal is 1.0 MHz. The frequency of the audio subcarrier signal is 6.0 MHz. The deviation of the carrier by the subcarrier is 1.0 MHz.

1-17-06 Mike Kuo CCS Dear Sir: In regard to the question that has been raised about the difference between the photos of the device in the SAR test and part 90 reports. The device that is correctly shown in the photos taken during the part 90 certification test is the transmitter module that is actually installed into the housing photographed during the SAR test. The SAR testing lab requested that we supply the complete device. This was requested so the lab could complete the SAR testing as the operator would use or hold the device. The SAR lab photographed the assembled device as they tested it and apparently did not photograph the transmitter module. The transmitter module, pictured in the part 90 test photos, is installed in the device housing along with the video camera, the batteries and supporting circuit boards. The device housing protects the components from the surrounding environment. I hope this has cleared up any confusion. If you have any further questions, please contact me at 661-588-6270. Sincerely, Scott Park President Search Systems, Inc.

Mike Kuo From: Kyle Fujimoto [[email protected]] Sent: Tuesday, January 17, 2006 4:24 PM To: Mike Kuo Subject: Responses to Search Systems Attachments: Search Systems -TransmitterModule vs Housing letter.pdf; Video Transmitter EmissionDesignator.pdf  2/11/2006 Mike, Sorry for the delay on this. We finally got the responses for the Search Systems application. Question #1: The device that we tested in 2002 for SAR evaluation is displayed below: (pics removed) which is very different than the device in the internal and external photos. Could you please show the relation between the device listed in the part 90 report and the one in the SAR test report? Response: Attached is a letter from Search Systems, Inc. explaining the difference between the device in the part 90 report and the one in the SAR test report. Question #2: AS indicated in the TCB application form, the necessary bandwidth is 11 MHz. Is 11 MHz based upon 99% measurement? please point out the page number in the test report. Response: The emissions designator is based on the 2M + 2D method. Attached will be a paragraph explaining how the emission designator was derived. I will also load these to the CCSEMC website also. Please let me know if you need any more information. Regards, Kyle Fujimoto Test Engineer -- Compatible Electronics, Inc. -- Brea Division Phone:(714) 579-0500 Fax: (714) 579-1850 [email protected] http://www.celectronics.com

REPORT NO: 02U1494-1 DATE: August 20, 2002 FCC ID: QL7SSIVTX01 COMPLIANCE CERTIFICATION SERVICES Page: 20 of 23 This report shall not be reproduced except in full, without the written approval of CCS. This document may be altered or revised by Compliance Certification Services personnel only, and shall be noted in the revision section of the document. 8. EUT PHOTOS

P.O. BOX 80307 · BAKERSFIELD, CA 93380-0307 · 661.588.6270 · 800.722.2824 · FAX 661.588.6274 FCC LABEL FOR QL7SSIVTX01 LABEL SIZE = 1” X 2”

in accordance with the requirements of FCC Report and Order: ET Docket 93-62, and OET Bulletin 65 Supplement C for Hazmat Wireless Video Camera MODEL: SSIVTX01 FCC ID: QL7SSIVTX01 AUGUST 20, 2002 REPORT NO: 02U1494-1 Prepared for SEARCH SYSTEMS, INC. P. O. BOX 80307 BAKERSFIELD, CA 93380, USA Prepared by COMPLIANCE CERTIFICATION SERVICES 561F MONTEREY ROAD, MORGAN HILL, CA 95037, USA TEL: (408) 463-0885 REPORT NO: 02U1494-1 DATE: August 20, 2002 FCC ID: QL7SSIVTX01 COMPLIANCE CERTIFICATION SERVICES Page: 2 of 23 This report shall not be reproduced except in full, without the written approval of CCS. This document may be altered or revised by Compliance Certification Services personnel only, and shall be noted in the revision section of the document. CERTIFICATE OF COMPLIANCE (SAR EVALUATION) Dates of Tests: August 16 & 20, 2002 Report No: 02U1494-1 APPLICANT: SEARCH SYSTEMS, INC. P. O. BOX 80307 BAKERSFIELD, CA 93380, USA MODEL: SSIVTX01 FCC ID: QL7SSIVTX01 DEVICE CATEGORY: PORTABLE DEVICES EXPOSURE CATEGORY: OCCUPATIONAL/CONTROLLED EXPOSURE Test Sample is a: Production unit Operating mode: Maximum continuous output Tx Frequency: 2462.5 & 2472.5 MHz Max. Output Power (Conducted): 27.03 dBm Max. SAR (1g): 1.40 mW/g (2462.5MHz; Left side) 1.02 mW/g (2472.5MHz; Left side) Separation distance: Direct touched to phantom Application Type: Certification FCC Rule Part(s): § 90 This wireless portable device has been shown to be capable of compliance for localized specific absorption rate (SAR) for uncontrolled environment/general population exposure limits specified in ANSI/IEEE Std. C95.1-1992 and had been tested in accordance with the measurement procedures specified in FCC OET 65 Supplement C (released on 6/29/2001 see Test Report). I attest to the accuracy of data. All measurements reported herein were performed by me or were made under my supervision and are correct to the best of my knowledge and belief. I assume full responsibility for the completeness of these measurements and vouch for the qualifications of all persons taking them. Steve Cheng EMC Engineering Manager REPORT NO: 02U1494-1 DATE: August 20, 2002 FCC ID: QL7SSIVTX01 COMPLIANCE CERTIFICATION SERVICES Page: 3 of 23 This report shall not be reproduced except in full, without the written approval of CCS. This document may be altered or revised by Compliance Certification Services personnel only, and shall be noted in the revision section of the document. TABLE OF CONTENT 1. EUT DESCRIPTION .............................................................................................4 2. REQUIREMENTS FOR COMPLIANCE TESTING DEFINED BY THE FCC...............5 3. DOSIMETRIC ASSESSMENT SYSTEM.................................................................5 3.1. MEASUREMENT SYSTEM DIAGRAM........................................................................................6 3.2. SYSTEM COMPONENTS...........................................................................................................7 4. EVALUATION PROCEDURE................................................................................9 5. MEASUREMENT UNCERTAINTY.......................................................................12 6. EXPOSURE LIMIT..............................................................................................13 7. MEASUREMENT RESULTS...............................................................................14 7.1. SYSTEM VALIDATION.............................................................................................................14 7.2. TEST LIQUID CONFIRMATION................................................................................................15 7.3. EUT TUNE-UP PROCEDURE...................................................................................................16 7.4. EUT SETUP PHOTOS..............................................................................................................17 7.5. SAR MEASUREMENT RESULT...............................................................................................19 8. EUT PHOTOS....................................................................................................20 9. EQUIPMENTS LIST & CALIBRATION STATUS ...................................................21 10. REFERENCES...................................................................................................22 11. ATTACHMENT..................................................................................................23 REPORT NO: 02U1494-1 DATE: August 20, 2002 FCC ID: QL7SSIVTX01 COMPLIANCE CERTIFICATION SERVICES Page: 4 of 23 This report shall not be reproduced except in full, without the written approval of CCS. This document may be altered or revised by Compliance Certification Services personnel only, and shall be noted in the revision section of the document. 1. EUT DESCRIPTION APPLICANT: SEARCH SYSTEMS, INC. P. O. BOX 80307 BAKERSFIELD, CA 93380, USA MODEL: SSIVTX01 FCC ID: QL7SSIVTX01 DEVICE CATEGORY: PORTABLE DEVICES EXPOSURE CATEGORY: OCCUPATIONAL/CONTROLLED EXPOSURE Test Sample is a: Production unit Operating mode: Maximum continuous output Tx Frequency: 2462.5 & 2472.5 MHz Max. Output Power (Conducted): 27.03 dBm Max. SAR (1g): 1.40 mW/g (2462.5MHz; Left side) 1.02 mW/g (2472.5MHz; Left side) Separation distance: Direct touched to phantom Application Type: Certification FCC Rule Part(s): § 90 Antenna Type: Fixed Antenna dimensions: Length: 88 mm; Width: 75 mm Battery option: Only one model with EUT 1 Specific Absorption Rate (SAR) is a measure of the rate of energy absorption due to exposure to an RF transmitting source (wireless portable device). 2 IEEE/ANSI Std. C95.1-1992 limits are used to determine compliance with FCC ET Docket 93-62. REPORT NO: 02U1494-1 DATE: August 20, 2002 FCC ID: QL7SSIVTX01 COMPLIANCE CERTIFICATION SERVICES Page: 5 of 23 This report shall not be reproduced except in full, without the written approval of CCS. This document may …

Text truncated - open the document above for the full version.

Search Systems, Inc. Model: SSIVTX01; Flat position; Frequency: 2462.5MHz Right side Frequency: 2450 MHz; Crest factor: 1.0 Medium: Muscle 2450 MHz: σ = 2.04 mho/m ε r = 50.2 ρ = 1.00 g/cm 3 SAM-1 Phantom; Flat Section; Position: (90°,90°) Probe: ET3DV6 - SN1578; ConvF(4.10,4.10,4.10); SAR:Cube 5x5x7: Peak: 2.17 mW/g, SAR (1g): 1.19 mW/g, SAR (10g): 0.684 mW/g, (Worst-case extrapolation) Penetration depth: 8.2 (7.6, 9.3) [mm]; Powerdrift: -0.01 dB Coarse: Dx = 14.0, Dy = 14.0, Dz = 10.0 Ambient Temperature (degree C): 23 Liquid Temperature (degree C): 21.2 SAR Tot [mW/g] 1.21E-1 3.63E-1 6.05E-1 8.47E-1 1.09E+0 08/16/02 COMPLIANCE CERTIFICATION SERVICES Search Systems, Inc. Model: SSIVTX01; Flat position; Frequency: 2462.5MHz Right side Frequency: 2450 MHz; Crest factor: 1.0 Medium: Muscle 2450 MHz: σ = 2.04 mho/m ε r = 50.2 ρ = 1.00 g/cm 3 SAM-1 Phantom; Section; Position: Probe: ET3DV6 - SN1578; ConvF(4.10,4.10,4.10); SAR:: , , () Penetration depth: 8.3 (7.7, 9.4) [mm]; Z-Axis: Dx = 0.0, Dy = 0.0, Dz = 2.0 Ambient Temperature (degree C): 23 Liquid Temperature (degree C): 21.2 08/16/02 COMPLIANCE CERTIFICATION SERVICES -0.2 0.0 0.2 0.4 0.6 0.8 1.0 1.2 1.4 1.6 1.8 2.0 2.2 102030405060708090100110 SAR tot [mW/g] [mm] Search Systems, Inc. Model: SSIVTX01; Flat position; Frequency: 2462.5MHz Left side Frequency: 2450 MHz; Crest factor: 1.0 Medium: Muscle 2450 MHz: σ = 2.04 mho/m ε r = 50.2 ρ = 1.00 g/cm 3 SAM-1 Phantom; Flat Section; Position: (90°,90°) Probe: ET3DV6 - SN1578; ConvF(4.10,4.10,4.10); SAR:Cube 5x5x7: Peak: 2.54 mW/g, SAR (1g): 1.40 mW/g, SAR (10g): 0.803 mW/g, (Worst-case extrapolation) Penetration depth: 8.1 (7.6, 9.1) [mm]; Powerdrift: -0.14 dB Coarse: Dx = 14.0, Dy = 14.0, Dz = 10.0 Ambient Temperature (degree C): 23 Liquid Temperature (degree C): 21.1 SAR Tot [mW/g] 1.40E-1 4.19E-1 6.98E-1 9.77E-1 1.26E+0 08/16/02 COMPLIANCE CERTIFICATION SERVICES Search Systems, Inc. Model: SSIVTX01; Flat position; Frequency: 2462.5MHz Left side Frequency: 2450 MHz; Crest factor: 1.0 Medium: Muscle 2450 MHz: σ = 2.04 mho/m ε r = 50.2 ρ = 1.00 g/cm 3 SAM-1 Phantom; Section; Position: Probe: ET3DV6 - SN1578; ConvF(4.10,4.10,4.10); SAR:: , , () Penetration depth: 8.3 (7.7, 9.3) [mm]; Z-Axis: Dx = 0.0, Dy = 0.0, Dz = 2.0 Ambient Temperature (degree C): 23 Liquid Temperature (degree C): 21.1 08/16/02 COMPLIANCE CERTIFICATION SERVICES -1.0 0.0 1.0 2.0 3.0 102030405060708090100110 SAR tot [mW/g] [mm] Search Systems, Inc. Model: SSIVTX01; Flat position; Frequency: 2462.5MHz Top side Frequency: 2450 MHz; Crest factor: 1.0 Medium: Muscle 2450 MHz: σ = 2.04 mho/m ε r = 50.2 ρ = 1.00 g/cm 3 SAM-1 Phantom; Flat Section; Position: (90°,90°) Probe: ET3DV6 - SN1578; ConvF(4.10,4.10,4.10); SAR:Cube 5x5x7: Peak: 0.982 mW/g, SAR (1g): 0.542 mW/g, SAR (10g): 0.313 mW/g, (Worst-case extrapolation) Penetration depth: 8.1 (7.6, 9.1) [mm]; Powerdrift: -0.09 dB Coarse: Dx = 14.0, Dy = 14.0, Dz = 10.0 Ambient Temperature (degree C): 23 Liquid Temperature (degree C): 21.2 SAR Tot [mW/g] 5.53E-2 1.66E-1 2.77E-1 3.87E-1 4.98E-1 08/16/02 COMPLIANCE CERTIFICATION SERVICES Search Systems, Inc. Model: SSIVTX01; Flat position; Frequency: 2462.5MHz Top side Frequency: 2450 MHz; Crest factor: 1.0 Medium: Muscle 2450 MHz: σ = 2.04 mho/m ε r = 50.2 ρ = 1.00 g/cm 3 SAM-1 Phantom; Section; Position: Probe: ET3DV6 - SN1578; ConvF(4.10,4.10,4.10); SAR:: , , () Penetration depth: 8.3 (7.7, 9.2) [mm]; Z-Axis: Dx = 0.0, Dy = 0.0, Dz = 2.0 Ambient Temperature (degree C): 23 Liquid Temperature (degree C): 21.2 08/16/02 COMPLIANCE CERTIFICATION SERVICES -0.1 0.0 0.1 0.2 0.3 0.4 0.5 0.6 0.7 0.8 0.9 1.0 102030405060708090100110 SAR tot [mW/g] [mm] Search Systems, Inc. MOdel: SSIVTX01; Flat position; Frequency: 2472.5MHz Right side Frequency: 2450 MHz; Crest factor: 1.0 Medium: Muscle 2450 MHz: σ = 2.04 mho/m ε r = 51.2 ρ = 1.00 g/cm 3 SAM-1 Phantom; Flat Section; Position: (90°,90°) Probe: ET3DV6 - SN1578; ConvF(4.10,4.10,4.10); SAR:Cube 5x5x7: Peak: 1.73 mW/g, SAR (1g): 0.947 mW/g, SAR (10g): 0.540 mW/g, (Worst-case extrapolation) Penetration depth: 8.1 (7.6, 9.1) [mm]; Powerdrift: -0.01 dB Coarse: Dx = 14.0, Dy = 14.0, Dz = 10.0 Ambient Temperature (degree C): 23 Liquid Temperature (degree C): 21.3 SAR Tot [mW/g] 1.01E-1 3.04E-1 5.07E-1 7.09E-1 9.12E-1 08/20/02 COMPLIANCE CERTIFICATION SERVICES Search Systems, Inc. MOdel: SSIVTX01; Flat position; Frequency: 2472.5MHz Right side Frequency: 2450 MHz; Crest factor: 1.0 Medium: Muscle 2450 MHz: σ = 2.04 mho/m ε r = 51.2 ρ = 1.00 g/cm 3 SAM-1 Phantom; Section; Position: Probe: ET3DV6 - SN1578; ConvF(4.10,4.10,4.10); SAR:: , , () Penetration depth: 8.3 (7.7, 9.2) [mm]; Z-Axis: Dx = 0.0, Dy = 0.0, Dz = 2.0 Ambient Temperature (degree C): 23 Liquid Temperature (degree C): 21.3 08/20/02 COMPLIANCE CERTIFICATION SERVICES -0.2 0.0 0.2 0.4 0.6 0.8 1.0 1.2 1.4 1.6 1.8 102030405060708090100110 SAR tot [mW/g] [mm] Search Systems, Inc. Model: SSIVTX01; Flat position; Frequency: 2472.5MHz Left side Frequency: 2450 MHz; Crest factor: 1.0 Medium: Muscle 2450 MHz: σ = 2.04 mho/m ε r = 51.2 ρ = 1.00 g/cm 3 SAM-1 Phantom; Flat Section; Position: (90°,90°) Probe: ET3DV6 - SN1578; ConvF(4.10,4.10,4.10); SAR:Cube 5x5x7: Peak: 1.87 mW/g, SAR (1g): 1.02 mW/g, SAR (10g): 0.584 mW/g, (Worst-case extrapolation) Penetration depth: 8.1 (7.6, 9.1) [mm]; Powerdrift: -0.01 dB Coarse: Dx = 14.0, Dy = 14.0, Dz = 10.0 Ambient Temperature (degree C): 23 Liquid Temperature (degree C): 21.2 SAR Tot [mW/g] 1.07E-1 3.21E-1 5.35E-1 7.50E-1 9.64E-1 08/20/02 COMPLIANCE CERTIFICATION SERVICES Search Systems, Inc. Model: SSIVTX01; Flat position; Frequency: 2472.5MHz Left side Frequency: 2450 MHz; Crest factor: 1.0 Medium: Muscle 2450 MHz: σ = 2.04 mho/m ε r = 51.2 ρ = 1.00 g/cm 3 SAM-1 Phantom; Section; Position: Probe: ET3DV6 - SN1578; ConvF(4.10,4.10,4.10); SAR:: , , () Penetration depth: 8.2 (7.7, 9.2) [mm]; Z-Axis: Dx = 0.0, Dy = 0.0, Dz = 2.0 Ambient Temperature (degree C): 23 Liquid Temperature (degree C): 21.2 08/20/02 COMPLI…

Text truncated - open the document above for the full version.

System Validation - D2450V2 S/N:706 (Antenna input power: 250 mW) SAM-2; Flat Probe: ET3DV6 - SN1578; ConvF(4.50,4.50,4.50); Crest factor: 1.0 Head 2450MHz: σ = 1.88 mho/m ε r = 38.9 ρ = 1.00 g/cm 3 Cube 5x5x7: Peak: 29.8 mW/g, SAR (1g): 14.2 mW/g, SAR (10g): 6.49 mW/g, (Worst-case extrapolation) Penetration depth: 6.4 (6.1, 7.1) [mm] Powerdrift: -0.01 dB Ambient Temperature (degree C): 23.0 Liquid Temperature (degree C): 21.2 SAR Tot [mW/g] 1.56E+0 4.69E+0 7.82E+0 1.09E+1 1.41E+1 08/16/02 COMPLIANCE CERTIFICATION SERVICES System Validation - D2450V2 S/N:706 (Antenna input power: 250 mW) SAM-2; Probe: ET3DV6 - SN1578; ConvF(4.50,4.50,4.50); Crest factor: 1.0 Head 2450MHz: σ = 1.88 mho/m ε r = 38.9 ρ = 1.00 g/cm 3 : , , () Penetration depth: 6.6 (6.3, 7.3) [mm] Ambient Temperature (degree C): 23.0 Liquid Temperature (degree C): 21.2 08/16/02 COMPLIANCE CERTIFICATION SERVICES 0 10 20 30 010203040506070 SAR tot [mW/g] [mm] System Validation - D2450V2 S/N:706 (Antenna input power: 250 mW) SAM-2; Flat Probe: ET3DV6 - SN1578; ConvF(4.50,4.50,4.50); Crest factor: 1.0 Head 2450MHz: σ = 1.89 mho/m ε r = 39.5 ρ = 1.00 g/cm 3 Cube 5x5x7: Peak: 28.6 mW/g, SAR (1g): 13.7 mW/g, SAR (10g): 6.24 mW/g, (Worst-case extrapolation) Penetration depth: 6.3 (6.1, 7.0) [mm] Powerdrift: -0.02 dB Ambient Temperature (degree C): 23.0 Liquid Temperature (degree C): 21.3 SAR Tot [mW/g] 1.44E+0 4.32E+0 7.20E+0 1.01E+1 1.30E+1 08/20/02 COMPLIANCE CERTIFICATION SERVICES System Validation - D2450V2 S/N:706 (Antenna input power: 250 mW) SAM-2; Probe: ET3DV6 - SN1578; ConvF(4.50,4.50,4.50); Crest factor: 1.0 Head 2450MHz: σ = 1.89 mho/m ε r = 39.5 ρ = 1.00 g/cm 3 : , , () Penetration depth: 6.4 (6.2, 7.1) [mm] Ambient Temperature (degree C): 23.0 Liquid Temperature (degree C): 21.3 08/20/02 COMPLIANCE CERTIFICATION SERVICES 0 10 20 30 01020304050607080 SAR tot [mW/g] [mm]

Report Number: B20809D1 FCC Part 90 and FCC Part 15 Class B Test Report 2.4 GHz Video Transmitter Model: SSIVTX01 114 OLINDA DRIVE, BREA, CALIFORNIA 92823 PHONE: (714) 579-0500 FAX: (714) 579-1850 Page 1 of 22 FCC PART 90 and PART 15, SUBPART B TEST REPORT for 2.4 GHZ VIDEO TRANSMITTER Model: SSIVTX01 Prepared for SEARCH SYSTEMS, INC. P.O. BOX 80307 BAKERSFIELD, CALIFORNIA 93380-0307 Prepared by:_____________________ KYLE FUJIMOTO Approved by:____________________ MICHAEL CHRISTENSEN COMPATIBLE ELECTRONICS INC. 114 OLINDA DRIVE BREA, CALIFORNIA 92823 (714) 579-0500 DATE: AUGUST 14, 2002 REPORT APPENDICES TOTAL BODY A B C D E PAGES 22 2 2 2 11 43 82 This report shall not be reproduced except in full, without the written approval of Compatible Electronics. Report Number: B20809D1 FCC Part 90 and FCC Part 15 Class B Test Report 2.4 GHz Video Transmitter Model: SSIVTX01 114 OLINDA DRIVE, BREA, CALIFORNIA 92823 PHONE: (714) 579-0500 FAX: (714) 579-1850 Page 2 of 22 TABLE OF CONTENTS Section / Title PAGE GENERAL REPORT SUMMARY 4 SUMMARY OF TEST RESULTS 5 1. PURPOSE 6 2. ADMINISTRATIVE DATA 7 2.1 Location of Testing 7 2.2 Traceability Statement 7 2.3 Cognizant Personnel 7 2.4 Date Test Sample was Received 7 2.5 Disposition of the Test Sample 7 2.6 Abbreviations and Acronyms 7 3. APPLICABLE DOCUMENTS 8 4. Description of Test Configuration 9 4.1 Description of Test Configuration - EMI 9 4.1.1 Cable Construction and Termination 10 5. LISTS OF EUT, ACCESSORIES AND TEST EQUIPMENT 11 5.1 EUT and Accessory List 11 5.2 EMI Test Equipment 12 6. TEST SITE DESCRIPTION 14 6.1 Test Facility Description 14 6.2 EUT Mounting, Bonding and Grounding 14 7. Test Procedures 15 7.1 Radiated Emissions Test for Part 15 15 7.2 Radiated Emissions (Spurious and Harmonics) Test for Part 90 17 7.3 Radiated Emissions (Spurious and Harmonics) Limit for Part 90 19 7.4 RF Power Output of the EUT 20 7.5 Modulation Characteristics – Audio Frequency Response 20 7.6 Modulation Characteristics – Audio Frequency Response 20 7.7 Occupied Bandwidth for the EUT 20 7.8 Spurious Emissions at the Antenna Terminal 21 7.9 Frequency Stability 21 8. CONCLUSIONS 22 Report Number: B20809D1 FCC Part 90 and FCC Part 15 Class B Test Report 2.4 GHz Video Transmitter Model: SSIVTX01 114 OLINDA DRIVE, BREA, CALIFORNIA 92823 PHONE: (714) 579-0500 FAX: (714) 579-1850 Page 3 of 22 LIST OF APPENDICES APPENDIX TITLE A Modifications to the EUT B Additional Models Covered Under This Report C Diagrams, Charts and Photos • Test Setup Diagrams • Radiated Emissions Photos • Antenna and Effective Gain Factors D Data Sheets E Laboratory Recognitions LIST OF FIGURES FIGURE TITLE 1 Plot Map And Layout of Test Site Report Number: B20809D1 FCC Part 90 and FCC Part 15 Class B Test Report 2.4 GHz Video Transmitter Model: SSIVTX01 114 OLINDA DRIVE, BREA, CALIFORNIA 92823 PHONE: (714) 579-0500 FAX: (714) 579-1850 Page 4 of 22 GENERAL REPORT SUMMARY This electromagnetic emission test report is generated by Compatible Electronics Inc., which is an independent testing and consulting firm. The test report is based on testing performed by Compatible Electronics personnel according to the measurement procedures described in the test specifications given below and in the "Test Procedures" section of this report. The measurement data and conclusions appearing herein relate only to the sample tested and this report may not be reproduced without the written permission of Compatible Electronics, unless done so in full. This report must not be used to claim product endorsement by NVLAP or any other agency of the U.S. Government. Device Tested: 2.4 GHz Video Transmitter Model: SSIVTX01 S/N: N/A Product Description: See Expository Statement. Modifications: The EUT was not modified during the testing. Manufacturer: Search Systems, Inc. P.O. Box 80307 Bakersfield, California 93380-0307 Test Date: June 14, 2002 File # For Canada: IC2154-D Test Specifications: EMI requirements CFR Title 47, Part 90, Subpart I; and CFR Title 47, Part 15, Subpart B Test Procedure: ANSI C63.4: 1992 and Test Deviations: The test procedure was not deviated from during the testing. Report Number: B20809D1 FCC Part 90 and FCC Part 15 Class B Test Report 2.4 GHz Video Transmitter Model: SSIVTX01 114 OLINDA DRIVE, BREA, CALIFORNIA 92823 PHONE: (714) 579-0500 FAX: (714) 579-1850 Page 5 of 22 SUMMARY OF TEST RESULTS TEST DESCRIPTION RESULTS 1 Conducted RF Emissions, 450 kHz - 30 MHz This test was not performed because the EUT operates on 7 Vdc only and will not be plugged into the AC public mains. 2 RF Power Output of the EUT Complies with the limits of CFR Title 47, Part 90, Section 90.205 (1) 3 Modulation Characteristics – Audio Frequency Response This test was not performed because this test is not applicable to the EUT 4 Modulation Characteristics – Modulation Limiting Response This test was not performed because this test is not applicable to the EUT 5 Occupied Bandwidth for the EUT Complies with the limits of CFR Title 47, Part 90 Section 90.210 (b) 6 Radiated RF Emissions on the Digital Portion 30 MHz – 25000 MHz Complies with the Class B limits of CFR Title 47, Part 15, Subpart B 7 Radiated Spurious Emissions on the Transmitter portion – 10 kHz to 25000 MHz Complies with the limits of CFR Title 47, Part 90 Section 90.210 (b) 8 Spurious Emissions at the Antenna Terminal Complies with the limits of CFR Title 47, Part 90 Section 90.210 (b) 9 Frequency Stability Complies with the limits of CFR Title 47, Part 90 Section 90.213 Report Number: B20809D1 FCC Part 90 and FCC Part 15 Class B Test Report 2.4 GHz Video Transmitter Model: SSIVTX01 114 OLINDA DRIVE, BREA, CALIFORNIA 92823 PHONE: (714) 579-0500 FAX: (714) 579-1850 Page 6 of 22 1. PURPOSE This document is a qualification test report based on the Electromagnetic Interference (EMI) tests performed on the 2.4 GHz Video Transmitter Model: SSIVTX01. The EMI measurements were performed according to the measurement procedure described in ANSI C63.4: 1992. The tests …

Text truncated - open the document above for the full version.