QTG-ZKUNIWireless Keyboard

UNIVERSAL NEED MORE HELP? PLEASE SEE OUR FAQ SECTION AT: www.ZAGG.com/faq *WARRANTY REGISTRATION Your ZAGGkeys™ Universal comes with a one-year manufacturer’s warranty. In order to activate the warranty, you must register your Universal as well as keep your purchase receipt. If you purchased your ZAGGkeys Universal from ZAGG.com, ZAGG® has already registered it and has a copy of your proof of purchase. If your device does not respond to your Universal there may be a simple explanation such as a dead battery or an unsuccessful pairing. Please use the following to help troubleshoot your situation. If none of the following solve your issue, then please contact ZAGG Customer Service and one of our trained professionals will be happy to assist you. 1. Restart your device and re-pair your Universal. 2. Turn your Universal o and back on. You should see the LED status lights illuminate briefly, if not, charge your Universal. 3. After charging, turn your Universal on. If the LED status lights do not illuminate, and your keyboard doesn’t operate correctly, please contact ZAGG’s Customer Support. 4. Forget and re-pair your Universal. Review your device’s instructions for how to properly forget a device, and then follow the directions under Pairing Your Universal. 5. If your device gives you an error message during pairing, repeat the pairing process. 8. If you still can’t get your Universal to pair, it is possible your device needs to have its software updated. Consult your device’s instructions for directions on how to update its software. 9. After your update is complete, repeat the troubleshooting/pairing process*. * If you continually receive the same error message during pairing, or the above steps don’t work, please contact ZAGG’s Customer Support for assistance. TROUBLESHOOTING FOR MORE HELP PLEASE SEE OUR FAQ AT: www.ZAGG.com/faq To reach a trained customer service representative, please use one of the following: ZAGG.com/support/contact.php | [email protected] 1-800-700-ZAGG [9244] | 00-1-801-839-3906 for international customers For unparalleled scratch protection for your device, we recommend ZAGG’s invisibleSHIELD®. ©2005 - 2013 ZAGG Inc. All Rights Reserved. PATENT PENDING | NASDAQ: ZAGG | MADE IN CHINA ZAGG®, invisibleSHIELD®, and ZAGGkeys™ Universal are trademarks or registered trademarks of ZAGG Inc. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: 1: This device may not cause harmful interference, and 2: This device must accept any interference received, including interference that may cause undesired operation FOLD FRONT BACK Congratulations on being the proud new owner of the most versatile Bluetooth® keyboard available. The ZAGGkeys Universal pairs with any of your Android, Windows, or iOS devices*. Read the following instructions in their entirely as some functions of the Universal work dierently depending on the device you are using. Keep these instructions for future reference. *Not all functions work, or work the same, across all operating systems and/or across all devices within an operating system. Please refer to the device specific tables under Special Function Keys for information on specific system key functions. CONGRATULATIONS Your ZAGGkeys Universal is ready to go right out of the box. Simply follow these steps to begin enjoying the Universal with any of your devices. 1. Remove the Universal from its packaging. 2. Slide the Universal Bluetooth® keyboard out of its protective cover by securing the cover and then sliding out the keyboard by pushing it to one side or the other. 3. Place the Universal keyboard in an ideal typing location. 5. Place the stand so that the now exposed trough sits on a flat surface. 6. Set your device in the trough (you can choose portrait or landscape mode) 7. Turn on your ZAGGkeys Universal using the power switch on the right hand side. 8. Select your operating system using the selector switch on the underside of the Universal keyboard. 9. Pair the Universal with your device (for information on pairing, see Pairing Your Universal). 10. Enjoy the ease and comfort of your Universal. QUICK START WINDOWS DEVICE 4. How to open the built-in device stand. •Hold the protective cover in one hand with your thumb on the ZAGG logo that appears on the outside of the cover. •Place your other hand on the opposite side of the cover with your finger/s inside the cover on the edge of the hinged stand. •Press outward with your fingers so that the hinged stand moves toward your thumb. N /A Alt Home Lock N /A N /A N /A Cut Copy Paste Track Back Play/Pause TrackForward Mute Vol Down Vol Up Function Launches themenu on theright side of the screen Forward Delete ctrl + beginning of line ctrl + end of line ctrl +top of page ctrl + bottom of page Functions in the lower right hand corner are accessed by pressing Fn + the key. FOLD INSIDE BACK INSIDE FRONT Your Universal features a powerful lithium-ion battery that lasts for up to three months of normal use between charges. It comes with a charging cable you can use to charge your keyboard quickly and conveniently. To charge your Universal, simply follow these steps: 1. Plug the micro USB connector into the charging port. 2. Plug the regular USB connector into any USB outlet (including a ZAGGsparq™, your computer, your device, etc.). 3. A green LED light will illuminate to indicate the Universal is charging. Wait until this light turns o, indicating a full charge. It usually takes 2-4 hours to completely charge your Universal. 4. Remove the Micro USB connector and enjoy your Universal for up to three months before you need to charge it again. CHARGINGAPPLE DEVICE As mentioned, the Universal features a powerful, rechargeable battery that lasts up to three months between charges*. To check your Universal’s remaining battery power, simply hold down the function (fn) key and press the battery key (also the CTRL key). The LED indicator will flash one of three way…

Text truncated - open the document above for the full version.

ZAGG Inc. Model: ZAGG Universal+ REPORT NO.: STR14038329I FCC PART 15.247 EXHIBIT 2 - EUT EXTERNAL PHOTOGRAPHS EUT View 1 EUT View 2 ZAGG Inc. Model: ZAGG Universal+ REPORT NO.: STR14038329I FCC PART 15.247 EUT View 3 EUT View 4 ZAGG Inc. Model: ZAGG Universal+ REPORT NO.: STR14038329I FCC PART 15.247 EUT View 5 EUT View 6 ZAGG Inc. Model: ZAGG Universal+ REPORT NO.: STR14038329I FCC PART 15.247 EUT View 7

ZAGG Inc. Model: ZAGG Universal+ REPORT NO.: STR14038329I FCC PART 15.247 EXHIBIT 1 - PRODUCT LABELING Proposed FCC ID Label Format FCC ID: QTG-ZKUNI This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Specifications: Text is Black in color and justified. Labels are printed in indelible ink on permanent adhesive silk-screened onto the EUT or shall be affixed at a conspicuous location on the EUT. Proposed Label Location on EUT FCC ID Label Location at the back side of EUT

ZAGG Inc. Model: ZAGG Universal+ REPORT NO.: STR14038329I FCC PART 15.247 EXHIBIT 1 - PRODUCT LABELING Proposed FCC ID Label Format FCC ID: QTG-ZKUNI This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Specifications: Text is Black in color and justified. Labels are printed in indelible ink on permanent adhesive silk-screened onto the EUT or shall be affixed at a conspicuous location on the EUT. Proposed Label Location on EUT FCC ID Label Location at the back side of EUT

ZAGG Inc. Model: ZAGG Universal+ REPORT NO.: STR14038329I FCC PART 15.247 EXHIBIT 3 - EUT INTERNAL PHOTOGRAPHS EUT Housing and Board View 1 (With 500mAh battery) EUT Housing and Board View 2 (With 1500mAh battery) ZAGG Inc. Model: ZAGG Universal+ REPORT NO.: STR14038329I FCC PART 15.247 Solder Board-Component View 1 Solder Board-Component View 2 ZAGG Inc. Model: ZAGG Universal+ REPORT NO.: STR14038329I FCC PART 15.247 Solder Board-Component View 3 Solder Board-Component View 4 ZAGG Inc. Model: ZAGG Universal+ REPORT NO.: STR14038329I FCC PART 15.247 Solder Board-Component View 5 Antenna View Ant. 2402-2480MHz

RF Exposure Requirements Product Description: Wireless Keyboard Model No.: ZAGG Universal+ FCC ID: QTG-ZKUNI According to the KDB-447498 D01 V05r02, the following RF exposure evaluation shall to demonstrate RF exposure compliance. Bluetooth Tx frequency range: 2402~2480MHz Device category: Portable device (Distance: 5mm) Maximum Conducted Output Power: -4.364 dBm Maximum Antenna Gain: 0 dBi Maximum EIRP Output Power: 0.3661mW Limit: 10mW Source-based time-averaged EIRP output power is 0.3661 mW < 10 mW So the transmitter complies with the RF exposure requirements and the SAR is not required.

ZAGG Inc. Model: ZAGG Universal+ REPORT NO.: STR14038329I PAGE 1 OF 48 FCC PART 15.247 FCC Part 15C Measurement and Test Report For ZAGG Inc. 3855 South 500 West Salt Lake City, UT 84115 USA FCC ID: QTG-ZKUNI FCC Rules: FCC Part 15.247 Product Description: Wireless Keyboard Tested Model: ZAGG Universal+ Report No.: STR14038329I Tested Date: 2014-03-11 to 2014-03-14 Issued Date: 2014-03-14 Tested By: Susan Su / Engineer Reviewed By: Lahm Peng / EMC Manager Approved & Authorized By: Jandy so / PSQ Manager Prepared By: Shenzhen SEM.Test Technology Co., Ltd. 1/F, Building A, Hongwei Industrial Park, Liuxian 2nd Road, Bao'an District, Shenzhen, P.R.C.（518101） Tel.: +86-755-33663308 Fax.: +86-755-33663309 Website: www.semtest.com.cn Note: This test report is limited to the above client company and the product model only. It may not be duplicated without prior permitted by Shenzhen SEM.Test Technology Co., Ltd. ZAGG Inc. Model: ZAGG Universal+ REPORT NO.: STR14038329I PAGE 2 OF 48 FCC PART 15.247 TABLE OF CONTENTS 1. GENERAL INFORMATION ................................................................................................................................... 4 1.1 PRODUCT DESCRIPTION FOR EQUIPMENT UNDER TEST (EUT) ............................................................................... 4 1.2 TEST STANDARDS ................................................................................................................................................... 5 1.3 TEST METHODOLOGY ............................................................................................................................................. 5 1.4 TEST FACILITY ....................................................................................................................................................... 5 1.5 EUT SETUP AND TEST MODE ................................................................................................................................. 6 2. SUMMARY OF TEST RESULTS ........................................................................................................................... 7 3. RF EXPOSURE ......................................................................................................................................................... 8 3.1 STANDARD APPLICABLE ......................................................................................................................................... 8 3.2 TEST RESULT.......................................................................................................................................................... 8 4. ANTENNA REQUIREMENT .................................................................................................................................. 9 4.1 STANDARD APPLICABLE ......................................................................................................................................... 9 4.2 EVALUATION INFORMATION .................................................................................................................................. 9 5. FREQUENCY HOPPING SYSTEM REQUIREMENTS ................................................................................... 10 5.1 STANDARD APPLICABLE ....................................................................................................................................... 10 5.2 FREQUENCY HOPPING SYSTEM............................................................................................................................. 10 5.3 EUT PSEUDORANDOM FREQUENCY HOPPING SEQUENCE .................................................................................... 11 6. QUANTITY OF HOPPING CHANNELS AND CHANNEL SEPARATION ................................................... 12 6.1 STANDARD APPLICABLE ....................................................................................................................................... 12 6.2 TEST EQUIPMENT LIST AND DETAILS ................................................................................................................... 12 6.3 TEST PROCEDURE ................................................................................................................................................. 12 6.4 ENVIRONMENTAL CONDITIONS ............................................................................................................................ 12 6.5 SUMMARY OF TEST RESULTS/PLOTS .................................................................................................................... 13 7. DWELL TIME OF HOPPING CHANNEL .......................................................................................................... 15 7.1 STANDARD APPLICABLE ....................................................................................................................................... 15 7.2 TEST EQUIPMENT LIST AND DETAILS ................................................................................................................... 15 7.3 TEST PROCEDURE ................................................................................................................................................. 15 7.4 ENVIRONMENTAL CONDITIONS ............................................................................................................................ 15 7.5 SUMMARY OF TEST RESULTS/PLOTS .................................................................................................................... 16 8. 20DB BANDWIDTH ............................................................................................................................................... 22 8.1 STANDARD APPLICABLE ....................................................................................................................................... 22 8.2 TEST EQUIPMENT LIST AND DETAILS ..................................................................................…

Text truncated - open the document above for the full version.

ZAGG Inc. Model: ZAGG Universal+ REPORT NO.: STR14038329I FCC PART 15.247 EXHIBIT 4 - TEST SETUP PHOTOGRAPHS Conducted Emission Test Setup Only Charging Radiation Emission Test Setup Only Charging ZAGG Inc. Model: ZAGG Universal+ REPORT NO.: STR14038329I FCC PART 15.247 Radiation Emission Test Setup (Below 30MHz) Radiation Emission Test Setup (30MHz to 1GHz) ZAGG Inc. Model: ZAGG Universal+ REPORT NO.: STR14038329I FCC PART 15.247 Radiation Emission Test Setup (Above 1GHz)