R6J6M2MWMM2micro Remote Unit

MRU6000 Installation Guide Statement This manual is property of M2Micro (Changshu) Co., Ltd. with all rights reserved. Any imitation, copying, transcript, or translation without the prior written permission of the Company is prohibited. Any dissemination of the product in any form or by any means (electronic, mechanical, photocopying, recording or otherwise) or any use for any commercial, or profit purpose is also forbidden. is a registered trademark solely for M2Micro (Changshu) Co., Ltd. All other trademarks or registered trademarks mentioned herein are owned by their respective owners. Product specifications and information referred in this manual are for reference only; we reserve the right to update relevant content without further notice. For more information, please visit our website at any time: http://www.m2micro.com Unless otherwise specified, this manual is only be used as guidance. While every attempt has been made to ensure all information in this manual is accurate, the Company should not be held liable for any error or omission in this document. FCC STATEMENT This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:  Reorient or relocate the receiving antenna.  Increase the separation between the equipment and receiver.  Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.  Consult the dealer or an experienced radio/TV technician for help.. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: 1) This device may not cause harmful interference. 2) This device must accept any interference received, including interference that may cause undesired operation. ⚠Caution: Any changes or modifications to this device not explicitly approved by manufacturer could void your authority to operate this equipment. Preface Manual instruction This Installation Guide describes the hardware features, installation methods and points for attention during installation. To avoid possible equipment damage or personal injury before and during the installation process, please read this manual carefully. Overview of this guide Chapter Instruction 1 Introduction Outlined the basic functionality and product features. 2 Installation Describes product installation methods and attentions A Data sheet Lists the hardware specifications. Version Date Version Update description 2011-11-30 R20111130-V1.00 Initial release. 2013-2-22 R20130222-V1.01 Increase FCC certification. Conventions Unless otherwise specified, the terms of ”systems”, “equipment”, “products” in the following parts of this manual refer to the MMR6000 meter reading system. Two signs are used herein to draw the users’ attention during the operation, with meanings as follows: ⚠Caution This icon is used to list advertent items during operation and to remind the users of undesirable consequences due to inaccurate operation, such as potential damage to the equipment or otherwise.  Tips This icon is to give supplementary explanation for the operation details described. I Contents 1 Introduction ................................................................................................ 1 1.1 Product Overview ............................................................................................ 1 1.2 Features ........................................................................................................... 2 1.3 Demonstration of the type .............................................................................. 2 2 Installation .................................................................................................. 5 2.1 Packing list ....................................................................................................... 5 2.2 Internal structure ............................................................................................ 5 2.3 MRU6000-BP01 ............................................................................................... 6 2.3.1 Product introduction .............................................................................. 6 2.3.2 Product dimension ................................................................................. 6 2.3.3 Product installation ................................................................................ 7 2.3.4 Connection ............................................................................................. 7 2.4 MRU6000-EM01 .............................................................................................. 8 2.4.1 Product introduction .............................................................................. 8 2.4.2 Product dimension ................................................................................. 8 2.4.3 Product installation ................................................................................ 8 2.5 MRU6000-WM01 ............................................................................................ 9 2.5.1 Product introduction .............................................................................. 9 2.5.2 Product appearance ............................................................................. 10 2.5.3 LEDs introduction .......................…

Text truncated - open the document above for the full version.

M2micro (Changshu) Co., Ltd. Address: No.1bldg, Science Technology Park, Sihai Road, Economic Development Zone, Changshu, Jiangsu 215503, China Tel: 651-779-4824 Fax: 651-779-4884 Date: 2013-02-02 To: SIEMIC, INC. 775 Montague Expressway, Milpitas, CA 95035 USA FCC ID: R6J6M2MWM Dear Sir/Madam, We, M2micro (Changshu) Co., Ltd. Hereby declares This EUT used a external antenna is fixed permanently by special glue. The max. gain is 2.0dBi. we will promise to implement this on all marketed product. Detail please refer to bellow: Sincerely, Client’s name / title : Xiaohong Ru / HR specialist Contact information / address : No.1bldg, Science Technology Park, Sihai Road, Economic Development Zone, Changshu, Jiangsu 215503, China Phone: +86-132-4760-9701 Fax: +86-512-5201-0002 E-Mail: [email protected] The Antenna was fixed permanently by special glue (AB Glue)

SCS-F18: Project and Product Certification Representative Authorization Letter Page 1 of 2 Rev 3.0 775 Montague Expressway Milpitas, CA 95035 Tel: 408-526-1188 Fax: 408-526-1088 Email: [email protected] Project and Product Certification Representative Authorization Letter Revision History Reason for Amendment (current / obsolete) From To Approved Date Initial Release (obsolete) 1.0 1.0 Nov-14-2006 Revised wording (obsolete) 1.0 2.0 Sept–25-2007 Updated company template (current) 2.0 3.0 Jan-31-2012 SCS-F18: Project and Product Certification Representative Authorization Letter Page 2 of 2 Rev 3.0 M2micro (Changshu) Co., Ltd. Address: No.1bldg, Science Technology Park, Sihai Road, Economic Development Zone, Changshu, Jiangsu 215503, China Tel: 651-779-4824 Fax: 651-779-4884 2013-02-04 To: SIEMIC, INC. 775 Montague Expressway, Milpitas, CA 95035 USA FCC ID: R6J6M2MWM Dear Sir/Madam, Re: Project and Product Certification Representative Authorization Letter We, M2micro (Changshu) Co., Ltd., hereby authorize SIEMIC, INC. to act as a Certification Body for certifying for the following project(s): Product name: M2micro Remote Unit Model no.: MRU6000-WM01 Sincerely, Client’s name / title : Xiaohong Ru / HR specialist Contact information / address : No.1bldg, Science Technology Park, Sihai Road, Economic Development Zone, Changshu, Jiangsu 215503, China Phone: +86-132-4760-9701 Fax: +86-512-5201-0002 E-Mail: [email protected]

SCS-F19: Confidentiality Request Letter Page 1 of 2 Rev 3.0 775 Montague Expressway Milpitas, CA 95035 Tel: 408-526-1188 Fax: 408-526-1088 Email: [email protected] Confidentiality Request Letter Revision History Reason for Amendment (current / obsolete) From To Approved Date Initial Release (obsolete) 1.0 1.0 Nov-14-2006 Adding CFR 2.459 (obsolete) 1.0 2.0 August – 11 - 2008 Updated company template & Added text box (current) 2.0 3.0 Jan-31-2012 SCS-F19: Confidentiality Request Letter Page 2 of 2 Rev 3.0 M2micro (Changshu) Co., Ltd. Address: No.1bldg, Science Technology Park, Sihai Road, Economic Development Zone, Changshu, Jiangsu 215503, China Tel: 651-779-4824 Fax: 651-779-4884 2013-02-02 To: Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD Confidentiality Request regarding application for certification of FCC ID: R6J6M2MWM We hereby request confidential treatment of information accompanying this application as outlined below: - Schematics Diagram - Block Diagram - Operation description The above materials contain trade secrets and proprietary information not customarily released to the public. The public disclosure of these materials may be harmful to the applicant and provide unjustified benefits to its competitors. The applicant understands that pursuant to Section 0.457 & 0.459 of the Rules, disclosure of this application and all accompanying documentation will not be made before the date of the Grant for this application. Sincerely, Client’s name / title : Xiaohong Ru / HR specialist Contact information / address : No.1bldg, Science Technology Park, Sihai Road, Economic Development Zone, Changshu, Jiangsu 215503, China Phone: +86-132-4760-9701 Fax: +86-512-5201-0002 E-Mail: [email protected]

SHENZHEN LCS COMPLIANCE TESTING LABORATORY LTD. FCC ID: R6J6M2MWM Report No.: LCS121101007QF ________________________________________________________________________________ _________ This report shall not be reproduced except in full, without the written approval of Shenzhen LCS Compliance Testing Laboratory Ltd.. Page 1 of 4 1. EXTERIOR PHOTOGRAPHS Fig.1 Fig.2 SHENZHEN LCS COMPLIANCE TESTING LABORATORY LTD. FCC ID: R6J6M2MWM Report No.: LCS121101007QF ________________________________________________________________________________ _________ This report shall not be reproduced except in full, without the written approval of Shenzhen LCS Compliance Testing Laboratory Ltd.. Page 2 of 4 Fig.3 Fig.4 SHENZHEN LCS COMPLIANCE TESTING LABORATORY LTD. FCC ID: R6J6M2MWM Report No.: LCS121101007QF ________________________________________________________________________________ _________ This report shall not be reproduced except in full, without the written approval of Shenzhen LCS Compliance Testing Laboratory Ltd.. Page 3 of 4 Fig.5 Fig.6 The Antenna was fixed permanently by special glue SHENZHEN LCS COMPLIANCE TESTING LABORATORY LTD. FCC ID: R6J6M2MWM Report No.: LCS121101007QF ________________________________________________________________________________ _________ This report shall not be reproduced except in full, without the written approval of Shenzhen LCS Compliance Testing Laboratory Ltd.. Page 4 of 4 Fig.7 Fig.8

SHENZHEN LCS COMPLIANCE TESTING LABORATORY LTD. FCC ID: R6J6M2MWM Report No.: LCS121101007QF ________________________________________________________________________________ _________ This report shall not be reproduced except in full, without the written approval of Shenzhen LCS Compliance Testing Laboratory Ltd.. Page 1 of 1 LABEL AND LOCATION Size: 4.0cm(L) x 6.0cm(W) Label Location

SHENZHEN LCS COMPLIANCE TESTING LABORATORY LTD. FCC ID: R6J6M2MWM Report No.: LCS121101007QF ________________________________________________________________________________ _________ This report shall not be reproduced except in full, without the written approval of Shenzhen LCS Compliance Testing Laboratory Ltd.. Page 1 of 3 1. INTERIOR PHOTOGRAPHS Fig.1 Fig.2 SHENZHEN LCS COMPLIANCE TESTING LABORATORY LTD. FCC ID: R6J6M2MWM Report No.: LCS121101007QF ________________________________________________________________________________ _________ This report shall not be reproduced except in full, without the written approval of Shenzhen LCS Compliance Testing Laboratory Ltd.. Page 2 of 3 Fig.3 Fig.4 SHENZHEN LCS COMPLIANCE TESTING LABORATORY LTD. FCC ID: R6J6M2MWM Report No.: LCS121101007QF ________________________________________________________________________________ _________ This report shall not be reproduced except in full, without the written approval of Shenzhen LCS Compliance Testing Laboratory Ltd.. Page 3 of 3 Fig.5 Fig.6

SHENZHEN LCS COMPLIANCE TESTING LABORATORY LTD. FCC ID: R6J6M2MWM Report No.: LCS121101007QF This report shall not be reproduced except in full, without the written approval of Shenzhen LCS Compliance Testing Laboratory Ltd.. Page 1 of 26 FCC TEST REPORT For M2micro (Changshu) Co., Ltd. M2micro Remote Unit Model No.: MRU6000-WM01 Prepared for : M2micro (Changshu) Co., Ltd. Address : No.1bldg, Science Technology Park, Sihai Road, Economic Development Zone, Changshu, Jiangsu 215503, China Prepared by : Shenzhen LCS Compliance Testing Laboratory Ltd. Address : 1F., Xingyuan Industrial Park, Tongda Road, Bao’an Blvd., Bao’an District, Shenzhen, Guangdong, China Date of receipt of test sample : November 11, 2012 Number of tested samples : 1 Serial number : Prototype Date of Test : November 11, 2012 – February 1, 2013 Date of Report : February 1, 2013 SHENZHEN LCS COMPLIANCE TESTING LABORATORY LTD. FCC ID: R6J6M2MWM Report No.: LCS121101007QF This report shall not be reproduced except in full, without the written approval of Shenzhen LCS Compliance Testing Laboratory Ltd.. Page 2 of 26 FCC TEST REPORT FCC CFR 47 PART 15 C(15.231) Report Reference No. .............. : LCS121101007QF Date of Issue ................................ : February 1, 2013 Testing Laboratory Name ......... : Shenzhen LCS Compliance Testing Laboratory Ltd. Address ........................................ : 1F., Xingyuan Industrial Park, Tongda Road, Bao’an Blvd., Bao’an District, Shenzhen, Guangdong, China Testing Location/ Procedure........ : Full application of Harmonised standards ■ Partial application of Harmonised standards □ Other standard testing method □ Applicant’s Name....................... : M2micro (Changshu) Co., Ltd. Address ........................................ : No.1bldg, Science Technology Park, Sihai Road, Economic Development Zone, Changshu, Jiangsu 215503, China Test Specification Standard ....................................... : FCC CFR 47 PART 15 Subpart C, ANSI C63.4-2003 Test Report Form No. .................. : LCSEMC-1.0 TRF Originator ............................ : Shenzhen LCS Compliance Testing Laboratory Ltd. Master TRF .................................. : Dated 2011-03 SHENZHEN LCS COMPLIANCE TESTING LABORATORY LTD. All rights reserved. This publication may be reproduced in whole or in part for non-commercial purposes as long as the Shenzhen LCS Compliance Testing Laboratory Ltd. is acknowledged as copyright owner and source of the material. Shenzhen LCS Compliance Testing Laboratory Ltd. takes no responsibility for and will not assume liability for damages resulting from the reader's interpretation of the reproduced material due to its placement and context. Test Item Description. ............... : M2micro Remote Unit Trade Mark .................................. : M2Micro Manufacturer................................ : M2micro (Changshu) Co., Ltd. Model/ Type reference................. : MRU6000-WM01 Ratings ......................................... : Input: AC 110-240V, 50/60Hz Output: DC 9V, 3A Result ......................................... : Positive Compiled by: Supervised by: Approved by: Ada Liang / File administrators Vito Cao/ Technique principal Gavin Liang/ Manager SHENZHEN LCS COMPLIANCE TESTING LABORATORY LTD. FCC ID: R6J6M2MWM Report No.: LCS121101007QF This report shall not be reproduced except in full, without the written approval of Shenzhen LCS Compliance Testing Laboratory Ltd.. Page 3 of 26 FCC TEST REPORT Test Result: Positive The test report merely corresponds to the test sample. It is not permitted to copy extracts of these test result without the written permission of the test laboratory. Test Report No. : LCS121101007QF February 1, 2013 Date of issue Type / Model........................... : MRU6000-WM01 EUT......................................... : M2micro Remote Unit Applicant............................... : M2micro (Changshu) Co., Ltd. Address.................................. : No.1bldg, Science Technology Park, Sihai Road, Economic Development Zone, Changshu, Jiangsu 215503, China Telephone............................... : / Fax.......................................... : / Manufacturer........................ : M2micro (Changshu) Co., Ltd. Address................................... : No.1bldg, Science Technology Park, Sihai Road, Economic Development Zone, Changshu, Jiangsu 215503, China Telephone............................... : / Fax.......................................... : / Factory................................... : M2micro (Changshu) Co., Ltd. Address................................... : No.1bldg, Science Technology Park, Sihai Road, Economic Development Zone, Changshu, Jiangsu 215503, China Telephone............................... : / Fax.......................................... : / SHENZHEN LCS COMPLIANCE TESTING LABORATORY LTD. FCC ID: R6J6M2MWM Report No.: LCS121101007QF This report shall not be reproduced except in full, without the written approval of Shenzhen LCS Compliance Testing Laboratory Ltd.. Page 4 of 26 TABLE OF CONTENTS 1. GENERAL INFORMATION .................................................................................................................................. 5 1.1. DESCRIPTION OF DEVICE (EUT) ...........................................................................................................................5 1.2. OBJECTIVE............................................................................................................................................................ 5 1.3. ENVIRONMENTAL CONDITIONS............................................................................................................................. 5 1.4. HOST SYSTEM CONFIGURATION LIST AND DETAILS............................................................................................. 6 1.5. EXTERNAL I/O PORT.................................................................................................................…

Text truncated - open the document above for the full version.

SHENZHEN LCS COMPLIANCE TESTING LABORATORY LTD. FCC ID: R6J6M2MWM Report No.: LCS121101007QF ________________________________________________________________________________ _________ This report shall not be reproduced except in full, without the written approval of Shenzhen LCS Compliance Testing Laboratory Ltd.. Page 1 of 2 1. TEST SETUP PHOTOGRAPHS 1.1. Photo of Radiated Emission Measurement Fig.1 Fig.2 SHENZHEN LCS COMPLIANCE TESTING LABORATORY LTD. FCC ID: R6J6M2MWM Report No.: LCS121101007QF ________________________________________________________________________________ _________ This report shall not be reproduced except in full, without the written approval of Shenzhen LCS Compliance Testing Laboratory Ltd.. Page 2 of 2 1.2. Photo of Conducted Emission Measurement Fig.1