RFM-EWS150GNA802.11 b/g Station

If you encounter problems when installing this product, contact your service provider. EDGE WIRELESS SYSTEM (EWS-150g) This wireless network device has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This wireless network device generates, uses, and radiates radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. For technical support, consult your Service Provider. Quick Start Guide Package Contents 1.EWS-150g unit 2.Antennas (2) 3.Ethernet cable (6 feet) 4.Power supply and cable (6 feet) 1 2 34 Connect the Antennas Attach both antennas to the unit. Do not apply excessive force when screwing on the antennas—just finger tight. 1 2 Position the Antennas Adjust both antennas to the upright position until they snap into place. 3 If you encounter problems when installing this product, contact your service provider. Choose a Suitable Location For best reception, the EWS-150g should be located as close as possible to a window or an outside wall. A convenient power outlet is required within 6 feet of the unit, and the LAN source (your computer) must be reachable with the supplied Ethernet cable (unless you purchase a longer cable). 4 Power On the Unit On the front panel of the unit, there are two LED indicators: •SIG For 802.11g wireless communication. •PWR Indicating that power is on. 7 Power Signal Plug & Play The installation of your EWS-150g Edge Wireless System is complete. You may verify correct operation using a computer connected to the Ethernet LAN by opening your browser and connecting to a Web site. The EWS-150g comes with some basic functions that allow you to monitor the unit’s performance and make physical adjustments to the antennas to maximize the available wireless signal. If your service provider allows guest access to the unit’s Web interface, log in then go to Step 9 to utilize these functions. Connect the Ethernet Cable If the unit will be connected to an Ethernet LAN, then connect one end of the Ethernet cable to the Ethernet socket on the rear of the unit, then connect the other end to the LAN port on your computer or router. 5 Ethernet cable Connect the Power Supply Plug the power supply connector into the power receptacle on the rear of the unit, then connect the power supply to the power outlet. 6 Power connector After applying power to the unit, the Power LED will flash for approximately 20 seconds. Following that, the Power LED should remain lit without flashing, and the Signal LED should flash intermittently. 8 If you encounter problems when installing this product, contact your service provider. Monitoring The EWS-150g is equipped with a variety of monitoring features and a troubleshooting aid, all of which are available from the Monitor tab in the unit’s Web interface. In addition, there are several quick links on the home page that will direct you to the key monitoring functions. The home page also includes an Antenna Aimer, which allows you to monitor signal strength while manually directing the unit’s antenna (this function is only available from the home page). Monitoring functions include: •Event Log •L2NAT •Troubleshooting •Wireless Neighbors •Statistics •Wireless History Because the EWS-150g monitors are intuitive and to avoid redundancy, this document does not provide examples of all available monitors. It does, however, provide an example of the Troubleshooting window and the Antenna Aimer. Where monitors are in tabular form the table can be sorted by column by simply clicking in the column header. For example, in Wireless Neighbors you may want to display the results sorted by RSSI value. In this case, click in the RSSI (dBm) column header. To reverse the displayed order (descending instead of ascending), click in the column header again. 9 If you encounter problems when installing this product, contact your service provider. Troubleshooting This feature is provided as a convenient tool for testing your wireless configuration and associations. To initiate the troubleshooting tool, click on the Monitor tab then click on Troubleshooting to display the Troubleshooting window. Click on the Start Troubleshooting button to begin the process. Antenna Aimer Available from the Home page, this tool is provided to assist you when attempting to find the optimum placement for the EWS-150g. The process is dynamic and interactive, which means that when you reposition the unit or its antennas you are presented with a response indicating the received signal strength. 10 11

Configuration Guide Edge Wireless System Front Matter Edge Wireless System (EWS-150g) Introducing the EWS-150g Configuration Updating the Firmware November 1st, 2006 210-0028-01 Rev. A Copyright © 2003 – 2006 Strix Systems, Inc. 26610 Agoura Road Calabasas, CA 91302 USA http://www.strixsystems.com Networks Without Wires ® iiEWS-150g Configuration Guide EWS-150g Configuration Guide EWS-150g Configuration Guideiii EWS-150g Configuration Guide Copyright Notice Copyright © 2006 Strix Systems, Inc. All rights reserved. This document may not be reproduced or disclosed in whole or in part by any means without the written consent of Strix Systems, Inc. Trademarks and brand names are marks of their respective holders. FCC Notice The enclosed wireless network device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: 1.This device may not cause harmful interference. 2.This device must accept any interference received, including interference that may cause undesired operation. This wireless network device has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This wireless network device generates, uses, and radiates radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this wireless network device does cause harmful interference to radio or television reception, which can be determined by turning the wireless network device off and on, the user is encouraged to try to correct the interference by one or more of the following measures: ◗Reorient or relocate the receiving antenna. ◗Increase the separation between the wireless network device and the affected receiver. ◗Connect the wireless network device into an outlet on a circuit different from that to which the receiver is connected. ◗Consult the dealer or an experienced radio/TV technician for help. European Community (EC) Directives and Conformity This wireless network device is in conformity with the Essential Requirements of R&TTE Directive 1999/5/EC of the European Union. Non-Modification Statement Unauthorized changes or modifications to Strix devices are not permitted. Modifications to Strix devices will void the warranty and may violate FCC or other regulations. RF Exposure Requirements To ensure compliance with FCC RF exposure requirements, the antenna used for this wireless network device must be installed to provide a separation distance of a minimum of 12 inches or more from all persons, and must not be co-located or operated in conjunction with any other antenna or radio transmitter. Installers and end-users must follow these installation instructions. ivEWS-150g Configuration Guide EWS-150g Configuration Guide Product Images Some of the images used in this document have been modified for clarity. For additional information, please visit us at: http://www.strixsystems.com. EWS-150g Configuration Guidev EWS-150g Configuration Guide Table of Contents Front Matter .................................................................................................................................. i Copyright Notice ................................................................................................................................... iii FCC Notice ........................................................................................................................................... iii European Community (EC) Directives and Conformity .......................................................................... iii Product Images ..................................................................................................................................... iv Table of Contents ..........................................................................................................................v An Introduction to the EWS-150g ................................................................................................1 Overview ............................................................................................................................................... 1 Bridging the Network ...................................................................................................................... 1 802.11g Wireless Technology ......................................................................................................... 2 Installing the EWS-150g ............................................................................................................... 3 Factory Default Settings .......................................................................................................................... 3 Resetting the EWS-150g to its Factory Default State ................................................................................ 3 Managing the EWS-150g .............................................................................................................. 4 Connecting to the Unit ........................................................................................................................... 4 Logging In .............................................................................................................................................. 4 The Home Page ............................................................................................................................... 5 About the Country Code ........................................................................................................................ 6 Setting Up the User Login Parameters .................................................................................................... 7…

Text truncated - open the document above for the full version.

Strix Systems, Inc. Corporate Headquarters 26610 Agoura Road Calabasas CA 91302 tel. 1.877.STRIXSYS fax. 1.818.251.1099 [email protected] .www.strixsystems.com 14 February 2007 Compliance Certification Services Certification Division 561F Monterey Road Morgan Hill, CA 95037 To whom it may concern: We, the undersigned, hereby authorize the Testing Division of Compliance Engineering Services, Inc., d.b.a. Compliance Certification Services and hereafter referred to as CCS, to act on our behalf in all manners relating to application for equipment authorization, including signing of all documents relating to these matters. Any and all acts carried out by CCS on our behalf shall have the same effect as acts of our own. We, the undersigned, hereby certify that we are not subject to a denial of federal benefits, that includes FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1998, 21 U.S.C. 853(a). In authorizing CCS Testing Division as our agent, we still recognize that we are responsible to: a) comply with the relevant provisions of the certification program; b) make all necessary arrangements for the conduct of the evaluation, including provision for examining documentation and access to all areas, records (including internal audit reports) and personnel for the purposes of evaluation (e.g. testing, inspection, assessment, surveillance, reassessment) and resolution of complaints; c) make claims regarding certification only in respect of the scope for which certification has been granted; d) do not use our product certification in such a manner as to bring the Certification Division into disrepute and not make any statement regarding our product certification which the Certification Division may consider misleading or unauthorized; Strix Systems, Inc. Corporate Headquarters 26610 Agoura Road Calabasas CA 91302 tel. 1.877.STRIXSYS fax. 1.818.251.1099 [email protected] .www.strixsystems.com e) upon suspension or cancellation of certification, discontinue use of all advertising matter that contains any reference thereto and return any certification documents as required by the Certification Division; f) use certification only to indicate the products are certified as being in conformity with specified standards; g) endeavor to ensure that no certificate or report nor any part thereof is used in a misleading manner; h) ensure that any reference to our product certification in communication media such as documents, brochures or advertising, complies with the requirements of the Certification Division; i) keep a record of all complaints made known to us relating to the product’s compliance with requirements of the relevant standard and to make these records available to the Certification Division when requested; j) take appropriate action with respect to such complaints and any deficiencies found in products or services that affect compliance with the requirements for certification; k) document the actions taken. This authorization is valid until further written notice from the applicant. Sincerely Yours, David Sardoni Project Manager Strix Systems, Inc.

Strix Systems, Inc. Corporate Headquarters 26610 Agoura Road Calabasas CA 91302 tel. 1.877.STRIXSYS fax. 1.818.251.1099 [email protected] .www.strixsystems.com 27 February 2007 Federal Communications Commission 7435 Oakland Mills Road Columbia, Maryland 21046 Subject: Request for withholding from public disclosure schematics, block diagrams, assembly drawings, operational specification, bill of materials and/or theory of operation. Gentlemen, Strix Systems, Inc., would like to request that all schematics, block diagrams, assembly drawings, operational specification, bill of materials and/or theory of operation submitted with our application for certification be withheld from public disclosure per Section 0.459 of the FCC rules. This request is made under the provisions of Section 0.457(d) of the Commissions rules, and Section 552(b)(4) of the Freedom of Information Act. These sections authorize the withholding from public inspection those materials which would be privileged as a matter of law if retained by the person submitting them, and materials which would not customarily be released to the public by that person. If you have any questions or need any additional information, please feel free to call me at (818) 251-1000. Sincerely, Steve Coffelt Director, Product Management

1 Mike Kuo From: September Radecki Sent: Tuesday, March 06, 2007 9:48 AM To: Helen Zhao Cc: Mike Kuo; Thu Chan; Julia Luke Subject: RE: STRIX SYSTEMS, INC., FCC ID: RFM-EWS150GNA, Assessment NO.: AN07T6541, Notice#1 Attachments: EWS150GNA Confidentiality Letter 02272007.pdf; Test Report Setup Photos.pdf; hg2405rd- rsp.pdf; 06U10677-1B FCC DTS Report.pdf EWS150GNA Confidentiality Lett.. Test Report Setup Photos.pdf (... hg2405rd-rsp.pdf (274 KB) 06U10677-1B FCC DTS Report.pd... Hi, Here are the answers to the questions asked during review of the above submission. Question #1: section 6 of test report, there are several test equipments listed are out of calibration. Please address this ISO Guide 17025 issue. <Answer:> The Report has been updated. There are several pieces of test equipment that are out for calibration now but were within their calibration date when the actual testing was done. These items are the Agilent/HP EMI Receiver, 9 kHz ~ 2.9 GHz, and the Agilent/HP RF Filter Section. Question #2: RF conducted output power were measured based upon different antenna gain and type. Please explain what the software is setting used for each of antenna. <Answer:> The client has decided to only pursue the 5.5 dBi antenna. Information is below on this. The Test Report has been updated to reflect a single antenna as well and is attached. Additionally, the antenna specification for this antenna is attached, as I don't see that in the original filing. Question #3: Throughout the user manual and quick installation guide, there is no information provided on the antenna gain Vs output power setting. Please include the power setting based upon the antenna gain in the user manual. Since the 9 dBi antenna gain antenna requires specific cable loss, such information is also needed in the user manual. <Answer:> The user is not able to modify settings, so no information is provided in the manual on how to do so. The 9 dBi antenna is no longer part of the project. Question #4: Is this device required professional installation? If yes, please provide justification for professional installation. <Answer:> The EWS150G does not require professional installation. Question #5: What is the antenna connector type? <Answer:> The antenna connector type is RP-SMA. Question #6: Internal photos are requested as confidential document. As indicated in the internal photos, this unit is not a sealed unit and has possibilities market to the general public. Please submit a revised confidentiality request letter or provide strong justification to explain why the internal photos should be considered as confidential document. <Answer:> Please see the attached revised confidentiality letter. The request for confidentiality for the internal photos has been removed. Question #7: As indicated in the functional block diagram and in the user manual, this device is capable of transmitting 5 GHz frequency. Please submit a marketing statement to indicate this device will only be marketed with 2.4 GHz radio and 5 GHz radio portion will be depopulated. <Answer:> The EWS150 PCB can only be populated as either a 2.4 GHz OR 5 GHz device, not as 2 both. The 5 GHz version of the EWS150 will not marketed or made available until the regulatory compliance process has been completed. Thank you for your time. Kindest regards, September Radecki -----Original Message----- From: Helen Zhao Sent: Tuesday, February 27, 2007 11:21 AM To: September Radecki Cc: Mike Kuo; Thu Chan Subject: STRIX SYSTEMS, INC., FCC ID: RFM-EWS150GNA, Assessment NO.: AN07T6541, Notice#1 Question #1: section 6 of test report, there are several test equipments listed are out of calibration. Please address this ISO Guide 17025 issue. Question #2: RF conducted output power were measured based upon different antenna gain and type. Please explain what the software is setting used for each of antenna. Question #3: Through out the user manual and quick installation guide, there is no information provided on the antenna gain Vs output power setting. Please include the power setting based upon the antenna gain in the user manual. Since the 9 dBi antenna gain antenna requires specific cable loss, such information is also needed in the user manual. Question #4: Is this device required professional installation? If yes, please provide justification for professional installation. Question #5: What is the antenna connector type? Question #6: Internal photos are requested as confidential document. As indicated in the internal photos, this unit is not a sealed unit and has possibilities market to the general public. Please submit a revised confidentiality request letter or provide strong justification to explain why the internal photos should be considered as confidential document. Question #7: As indicated in the functional block diagram and in the user manual, this device is capable of transmitting 5 GHz frequency. Please submit a marketing statement to indicate this device will only be marketed with 2.4 GHz radio and 5 GHz radio portion will be depopulated. Best Regards Helen Zhao The items indicated above must be submitted before processing can continue on the above referenced application. Failure to provide the requested information within 30 days of the original e-mail date may result in application dismissal and forfeiture of the filing fee. Also, please note that partial responses increase processing time and should not be submitted. Any questions about the content of this correspondence should be directed to the e-mail address listed below the name of the sender.

Strix Systems, Inc. Corporate Headquarters 26610 Agoura Road Calabasas CA 91302 tel. 1.877.STRIXSYS fax. 1.818.251.1099 [email protected] .www.strixsystems.com EWS150GNA Front EWS150GNA Back Strix Systems, Inc. Corporate Headquarters 26610 Agoura Road Calabasas CA 91302 tel. 1.877.STRIXSYS fax. 1.818.251.1099 [email protected] .www.strixsystems.com EWS150GNA Side EWS150GNA Bottom (Label Placement)

Strix Systems, Inc. Corporate Headquarters 26610 Agoura Road Calabasas CA 91302 tel. 1.877.STRIXSYS fax. 1.818.251.1099 [email protected] .www.strixsystems.com EWS150GNA Front EWS150GNA Back Strix Systems, Inc. Corporate Headquarters 26610 Agoura Road Calabasas CA 91302 tel. 1.877.STRIXSYS fax. 1.818.251.1099 [email protected] .www.strixsystems.com EWS150GNA Side EWS150GNA Bottom (Label Placement)

Strix Systems, Inc. Corporate Headquarters 26610 Agoura Road Calabasas CA 91302 tel. 1.877.STRIXSYS fax. 1.818.251.1099 [email protected] .www.strixsystems.com EWS150GNA Top Removed EWS150GNA PCB (Top) Strix Systems, Inc. Corporate Headquarters 26610 Agoura Road Calabasas CA 91302 tel. 1.877.STRIXSYS fax. 1.818.251.1099 [email protected] .www.strixsystems.com EWS150GNA PCB (Top - with shield removed) EWS150GNA PCB (Bottom) Strix Systems, Inc. Corporate Headquarters 26610 Agoura Road Calabasas CA 91302 tel. 1.877.STRIXSYS fax. 1.818.251.1099 [email protected] .www.strixsystems.com EWS150GNA Label

e-mail: [email protected] • tel: 561-995-2256 • fax: 561-995-2432 web: www.hyperlinktech.com • 1201 Clint Moore Road • Boca Raton FL 33487 2.4 GHz 5.5 dBi Reverse Polarity-SMA "Rubber Duck" Wireless LAN Antenna – Model: HG2405RD-RSP Applications and Features Applications: • 2.4 GHz ISM Band • IEEE 802.11b and 802.11g Wireless LAN • Bluetooth® • WiFi • Wireless Video Systems • Multipoint and Mobile Applications Features: • Flexible "Rubber Duck" antenna • Tilt and swivel design • RP-SMA Connector • RoHS Compliant • Optional Magnetic Mount Available Description This compact 2.4GHz omnidirectional "rubber-duck" WiFi antenna provides broad coverage and 5.5 dBi gain. It is a coaxial sleeve design with an omni-directional pattern. It is ideally suited for IEEE 802.11b and 802.11g wireless LANs, Bluetooth® and other WLAN applications. Measuring 8.2" long, this flexible antenna features a tilt-and-swivel reverse-polarity SMA connector, allowing them to be used vertically, at a right angle, or any angle in-between. It is suitable as a replacement RF antenna for many access points and radios that are equipped with reverse-polarity SMA connectors including D-Link®, Linksys® WET11 and others. Application Note: This antenna is not for use with U.S.Robotics® RP-SMA equipped devices. Specifications Frequency 2400-2500 MHz Gain 5.5 dBi Impedance 50 Ohm VSWR < 2.0 Weight 0.7 oz. (20 g) Length 8.2" (208 mm) Diameter 0.5" (13 mm) Finish Matte Black Connector Reverse Polarity SMA Plug Operating Temperature -40° C to to 85° C (-40° F to 185° F) Flame Rating UL 94HB Polarization Vertical RoHS Compliant Yes e-mail: [email protected] • tel: 561-995-2256 • fax: 561-995-2432 web: www.hyperlinktech.com • 1201 Clint Moore Road • Boca Raton FL 33487 Antenna Gain Pattern Guaranteed Quality This product is backed by Hyperlink's Limited Warranty Optional Magnetic Mount Model Description HMA6-RSPA10 Reverse-Polarity SMA-Jack (RP-SMA Jack) magnetic mount with 5 ft. high performance low-loss 100 series cable terminated with a Reverse-Polarity SMA Plug (RP-SMA Plug) connector. Custom connectors and cable lengths also available.

FCC CFR47 PART 15 SUBPART C CERTIFICATION TEST REPORT FOR 802.11 B/G STATION MODEL NUMBER: EWS150-G FCC ID: RFM-EWS150GNA REPORT NUMBER: 06U10677-1, REVISION B ISSUE DATE: MARCH 05, 2007 Prepared for STRIX SYSTEMS 26610 AGOURA ROAD, SUITE 110 CALABASAS, CA 91302, U.S.A. Prepared by COMPLIANCE CERTIFICATION SERVICES 47173 BENICIA STREET FREMONT, CA 94538, U.S.A. TEL: (510) 771-1000 FAX: (510) 661-0888 REPORT NO: 06U10677-1B DATE: MARCH 5, 2007 EUT: 802.11 b/g Station FCC ID: RFM-EWS150GNA Page 2 of 105 COMPLIANCE CERTIFICATION SERVICES DOCUMENT NO: CCSUP4031A 47173 BENICIA STREET, FREMONT, CA 94538, USA TEL: (510) 771-1000 FAX: (510) 661-0888 This report shall not be reproduced except in full, without the written approval of CCS. Revision History Rev. Issue Date Revisions Revised By -- 02/13/07 Initial Issue T.C. B 03/05/07 Removed information on 2 antennas per client request. T.C. REPORT NO: 06U10677-1B DATE: MARCH 5, 2007 EUT: 802.11 b/g Station FCC ID: RFM-EWS150GNA Page 3 of 105 COMPLIANCE CERTIFICATION SERVICES DOCUMENT NO: CCSUP4031A 47173 BENICIA STREET, FREMONT, CA 94538, USA TEL: (510) 771-1000 FAX: (510) 661-0888 This report shall not be reproduced except in full, without the written approval of CCS. TABLE OF CONTENTS 1. ATTESTATION OF TEST RESULTS............................................................................................. 4 2. TEST METHODOLOGY .................................................................................................................. 5 3. FACILITIES AND ACCREDITATION .......................................................................................... 5 4. CALIBRATION AND UNCERTAINTY.......................................................................................... 5 4.1. MEASURING INSTRUMENT CALIBRATION ............................................................................. 5 4.2. MEASUREMENT UNCERTAINTY ............................................................................................... 5 5. EQUIPMENT UNDER TEST............................................................................................................6 5.1. DESCRIPTION OF EUT ..............................................................................................................6 5.2. MAXIMUM OUTPUT POWER .................................................................................................... 6 5.3. DESCRIPTION OF AVAILABLE ANTENNAS ............................................................................. 6 5.4. SOFTWARE AND FIRMWARE .................................................................................................... 6 5.5. WORST-CASE CONFIGURATION AND MODE......................................................................... 6 5.6. DESCRIPTION OF TEST SETUP ................................................................................................ 7 6. TEST AND MEASUREMENT EQUIPMENT .............................................................................. 11 7. LIMITS AND RESULTS ................................................................................................................. 12 7.1. CHANNEL TESTS FOR THE 2400 TO 2483.5 MHz BAND ...................................................... 12 7.1.1. 6 dB BANDWIDTH ........................................................................................................... 12 7.1.2. 99% BANDWIDTH............................................................................................................ 19 7.1.3. PEAK OUTPUT POWER .................................................................................................. 26 7.1.4. MAXIMUM PERMISSIBLE EXPOSURE ........................................................................ 33 7.1.5. AVERAGE POWER........................................................................................................... 36 7.1.6. PEAK POWER SPECTRAL DENSITY ............................................................................ 37 7.1.7. CONDUCTED SPURIOUS EMISSIONS.......................................................................... 44 7.2. RADIATED EMISSIONS.............................................................................................................57 7.2.1. TRANSMITTER RADIATED SPURIOUS EMISSIONS ................................................. 57 7.2.2. TRANSMITTER ABOVE 1 GHz FOR 2400 TO 2483.5 MHz BAND ............................. 60 7.2.3. WORST-CASE RADIATED EMISSIONS BELOW 1 GHz ............................................. 78 7.3. POWERLINE CONDUCTED EMISSIONS ................................................................................ 79 8. SETUP PHOTOS .............................................................................................................................. 89 REPORT NO: 06U10677-1B DATE: MARCH 5, 2007 EUT: 802.11 b/g Station FCC ID: RFM-EWS150GNA Page 4 of 105 COMPLIANCE CERTIFICATION SERVICES DOCUMENT NO: CCSUP4031A 47173 BENICIA STREET, FREMONT, CA 94538, USA TEL: (510) 771-1000 FAX: (510) 661-0888 This report shall not be reproduced except in full, without the written approval of CCS. 1. ATTESTATION OF TEST RESULTS COMPANY NAME: STRIX SYSTEMS 26610 AGOURA ROAD, SUITE 110 CALABASAS, CA 91302, U.S.A. EUT DESCRIPTION: 802.11 B/G STATION MODEL: EWS150-G SERIAL NUMBER: A1D26BA0021 DATE TESTED: DEC 12, 2006 – FEB 6, 2007 APPLICABLE STANDARDS STANDARD TEST RESULTS FCC PART 15 SUBPART C NO NON-COMPLIANCE NOTED Compliance Certification Services, Inc. tested the above equipment in accordance with the requirements set forth in the above standards. The test results show that the equipment te…

Text truncated - open the document above for the full version.