RHZDTL718-WHSPA+ Module

AnyDATA DTL718-W(-P) Module AT Command Reference M2M-AT014-03 2012.11.20 Send Technical Questions to: [email protected] AnyDATA (Shanghai) 489 SongTao Road, Sector B, 1 st FL. Pudong ZhangJiang Hi-Tech Park, Shanghai, 201203 Tel: +86(021) 5080-4828 Fax: +86(021) 5080-3828 AnyDATA Corporation 5 Oldfield Irvine, California 92618 USA http://www.anydata.com Copyright © AnyDATA Co., Ltd. 2011. All rights reserved. All data and information contained in or disclosed by this document are confidential and proprietary information of AnyDATA Corporation, and all rights therein are expressly reserved. By accepting this material, the recipient agrees that this material and the information contained therein are held in confidence and in trust and will not be used, copied, reproduced in whole or in part, nor its contents revealed in any manner to others without the express written permission of AnyDATA Corporation. Restricted Distribution. This document contains critical information about AnyDATA Corporation products and may not be distributed to anyone without permission of AnyDATA Corporation. All data and information contained in this document are proprietary and confidential information of AnyDATA Corporation. No part of this document may be reproduced, in any form or any means without written permission of AnyDATA Corporation. Notice Although the information in this document has been carefully reviewed and its believed to be reliable. AnyDATA Corporation does not assume any liability arising out of the application or use of any product described herein, Neither does it convey any license under its patent rights nor rights of others. Changes or modifications not expressly approved by the manufacturer could void the user’s authority to operate the equipment. If the FCC ID of the module cannot be seen when it is installed, then the host label Ref mus Max gain The be c Vers 0 0 0 0 UM UM Any ference t include th imum cond is as below antenna ca o-located w sion D 0 201 1 20 2 201 3 2012 Band MTS Band MTS Band DATA D he text: Co ducted out w: annot be in within 20c Date 2-5-25 I 12-8-2 A D 2-8-28 A A M 2-11-20 A P II V DTL718-W ontains FCC tput power nstalled to m of othe r nitial Vers Add +CLVL Delete set Add +CNM Add +CMU Modify ATS Add +ACE ( Maximum W(-P) M C ID: RHZD r (measure be used w r transmitte ion L\+CMUT command MP comma UT comman S7 default LLINFO co m conducte (dBm) 23.35 23.32 Module A DTL718-W d) and the within 20cm er antenna Do Descri commands of +WS46 nd nd value ommand ed output p ) AT Comm maximum m of any pe as. ocume ption s 6 power ) mand m permitted rsons and nt Hi Antenna (dB 4. 4. d antenna must not story a Gain Bi) 5 5 Ref M2M-AT0 1 O 2 B 3 C 4 N Any ference 14-03 Overview . 1.1 Scop 1.2 Nor m 1.3 Abbre 1.4 Defin Basic Comm 2.1 A/, R 2.2 ATE, 2.3 +CG M 2.4 +CGM 2.5 +CGS 2.6 +CSC 2.7 +CIM 2.8 +GCA 2.9 +CME Call Contro 3.1 ATA, 3.2 ATD, 3.3 ATH, 3.4 ATS 0 3.5 +CST 3.6 +CHU 3.7 +CRL 3.8 +CEE 3.9 +CRC 3.10 +CVH 3.11 +CMU 3.12 +VTS 3.13 +CLC 3.14 ATS, 3.15 +CC W 3.16 +CHL 3.17 +CCF Network S 4.1 +CNU 4.2 +CRE DATA D ................ e of Docum mative Refere eviations .... nitions ......... mands ...... epeating A C Command MI, Request MR, Reques SN, Reques CS, Select T MI , Request AP, Capabili EE, Report ol Comma Answer ...... Dial ........... Disconnec t 0, Enables/d TA, Selects T UP, Hangup LP, Radio Li ER, Extende C, Cellular R HU, Voice H UT, M i c r o ph S, DTMF And CC, List Curr S Paramete WA, Call Wa LD, Call Rel FC, Call For Service Com UM, Subscri EG, Network DTL718-W AnyDA ............... ent ............. ences ......... ................... ................... ............... Command L Echo .......... t Manufactur st Revision I st Serial Num TE Characte Internationa ities List ...... Mobile Equi nds .......... ................... ................... t .................. isables Auto Type of Add Call .......... . nk Protocol . ed Error Rep Result Code angup Con t hone Mute C d Tone Gen rent Calls .... ers .............. aiting ........... ated Supple rwarding Nu mmands ... iber Number k Registratio W(-P) M ATA © 2001 ................ ................... ................... ................... ................... ................ Line ............. ................... rer Identifica Identification mber Identifi er Set .......... al Mobile Su ................... pment Erro r ................ ................... ................... ................... omatic Answ ress ........... ................... ................... port ............. s ................ trol .............. Control ......... eration ....... ................... ................... ................... ementary Se mber and C ................ r ................. on Report ... Module A -2011 ................ .................. .................. .................. .................. ................ .................. .................. ation ........... n ................. cation ........ .................. ubscriber Ide .................. r ................. ................ .................. .................. .................. wering ......... .................. .................. .................. .................. .................. .................. .................. .................. .................. .................. .................. ervices ........ Conditions ... ................ .................. .................. AT Comm ................ .................. .................. .................. .................. ................ .................. .................. .................. .................. .................. .................. entity (IMSI) .................. .................. ................ .................. .................. .................. .................. .................. .................. .................. .................. .................. .................. .................. .................. .................. .................. ......…

Text truncated - open the document above for the full version.

Modular Approval Request Letter FCC ID: RHZDTL718-W Data: Dec.24, 2012 Gentlemen: There’s a HSPA+ Module that would like to have your authorization as a modular approval. The specific product as below, HSPA+ Module, with its designed features and specified description, meets special requirements for full modular approval on FCC Public Notice DA 00-1407 Released: June 26, 2000 by cross-reference list below. Company : AnyDATA (Shanghai) Co., Ltd Model Name : HSPA+ Module Model Number : DTL718-W FCC ID : RHZDTL718-W Requirement of Public Notice DA00‐1407 Reference to DTL718‐W 1. The modular transmitter must have its own RF shielding. The module has its own RF shielding. Please see external photo.pdf 2. The modular transmitter must have buffered modulation/data inputs. The modular has buffered data inputs, it is integrated in chip Qualcomm MDM6200. Please see schematic.pdf 3. The modular transmitter must have its own power supply regulation. All power lines derived from the host device are regulated before energizing other circuits internal to the DTL718‐W. Please see schematic.pdf 4. The modular transmitter must comply with the antenna requirements of Section 15.203 and 15.204(c). The DTL718‐W meets the FCC antenna requirements. It has a unique connector. Please see external photo.pdf 5. The modular transmitter must be tested in a stand‐alone configuration, i.e., the module must not be inside another device during testing. The DTL718‐W was tested in a stand‐alone configuration via a PCMCIA extender. Please see conducted set‐up photo.pdf and spurious set‐up 6. The modular transmitter must be labeled with its own FCC ID number, and, if the FCC ID is not visible when the module is installed inside another device, then the outside of the device into which the module is installed must also display a label referring to the enclosed module. The label position of DTL718‐W is clearly indicated. Please see the label.pdf 7. The modular transmitter must comply with any specific rule or operating requirements applicable to the transmitter and the manufacturer must provide adequate instructions along with the module to explain any such requirements. A copy of these instructions must be included in the application for equipment authorization. The DTL718‐W is compliant with all applicable FCC rules. Detail instructions are given in the Users Manual. Please see Installation guide.pdf 8. The modular transmitter must comply with any applicable RF exposure requirements. For example, FCC Rules in Sections 2.1091, 2.1093 and specific Sections of Part 15, including 15.319(i), 15.407(f), 15.253(f) and 15.255(g), require that Unlicensed PCS, UNII and millimeter wave devices perform routine environmental evaluation for RF Exposure to demonstrate compliance. In addition, spread spectrum transmitters operating under Section 15.247 are required to address RF Exposure compliance in accordance with Section 15.247(b)(4). The DTL718‐W comply with applicable RF exposure requirements. Please see RF safety evaluation. pdf Thank you. Sincerely, Rookie Yuan / QA Engineer AnyDATA (Shanghai) Co., Ltd Tel: 021-50804828 Fax: 021-50803828 Email: [email protected]

THIS MUST BE SIGNED BY THE APPLICANT/AGENT AND SHOULD BE PLACED ON APPROPRIATE LETTERHEAD Request for Confidentiality Date: 2012-12-19 Subject: Confidentiality Request for: _ RHZDTL718-W__ Pursuant to FCC 47 CRF 0.457(d) and 0.459 and IC RSP-100, Section 10, the applicant requests that a part of the subject FCC application be held confidential. Type of Confidentiality Requested Exhibit Short Term Permanent Block Diagrams Short Term External Photos Short Term Permanent* 1 Internal Photos Short Term Permanent Operation Description/Theory of Operation Short Term Permanent Parts List & Placement/BOM Short Term Permanent Tune-Up Procedure Short Term Permanent Schematics Short Term Test Setup Photos Short Term Permanent* User’s Manual *Note: ______(Insert Explanation as Necessary)______ _____ AnyDATA (Shanghai) Co., Ltd__ has spent substantial effort in developing this product and it is one of the first of its kind in industry. Having the subject information easily available to "competition" would negate the advantage they have achieved by developing this product. Not protecting the details of the design will result in financial hardship. Permanent Confidentiality: The applicant requests the exhibits listed above as permanently confidential be permanently withheld from public review due to materials that contain trade secrets and proprietary information not customarily released to the public. Short-Term Confidentiality: The applicant requests the exhibits selected above as short term confidential be withheld from public view for a period of ___(specify number of days not to exceed 180 ) 2 ___ days from the date of the Grant of Equipment Authorization and prior to marketing. This is to avoid premature release of sensitive information prior to marketing or release of the product to the public. Applicant is also aware that they are responsible to notify ACB in the event information regarding the product or the product is made available to the public. ACB will then release the documents listed above for public disclosure pursuant to FCC Public Notice DA 04-1705. NOTE for Industry Canada Applications: The applicant understands that until such time that IC distinguishes between Short Term and Permanent Confidentiality, either type of marked exhibit above will simply be marked Confidential when submitted to IC. Sincerely, By: Rookie Yuan ________________________ _________________________ (Signature/Title 3 ) (Print name) 1 - The asterisked items (*) require further justification before permanent confidentiality will be allowed. These also currently require review by the FCC under their Permit-But-Ask policy before the grant is issued and can delay completion of an application. Further justification should be added to the note above. One such example for a potted device would be: “The EUT is FULLY potted using a non-removable epoxy based material. Removal of potting material causes irreparable damage to internal circuitry. See photographs exhibits that outline the device before and after potting.” 2 - Please refer to http://acbcert.com/documents/misc-docs/Memo-Short-Term-Vs-Standard-Confidentiality.pdf for complete details. 3 - Must be signed by applicant contact given for applicant on the FCC site, or by the authorized agent if an appropriate THIS MUST BE SIGNED BY THE APPLICANT/AGENT AND SHOULD BE PLACED ON APPROPRIATE LETTERHEAD authorized agent letter has been provided. Letters should be placed on appropriate letterhead.

DTL718-W external photo

DTL718-W Internal photo

TA Technology (Shanghai)Co.,Ltd. Test Report Report No.: RXA1211-1096MPE01R1 Page 1 of 5 : MPE REPORT Product Name HSPA+ Module Manufacture AnyDATA Shanghai Co., Ltd Model DTL718-W FCC ID RHZDTL718-W Test date 2012-12-21 Approved by Director Revised by Manager Performed by Engineer Test By Company: TA Technology (Shanghai) Co., Ltd. Address: No.145, Jintang Rd, Tangzhen Industry Park, Pudong Shanghai,China Contact: Yang Weizhong Telephone: +86-021-50791141/2/3 Fax: +86-021-50791141/2/3-8000 Website: http://www.ta-shanghai.com E-mail: [email protected] TA Technology (Shanghai)Co.,Ltd. Test Report Report No.: RXA1211-1096MPE01R1 Page 2 of 5 Maximum Permissible Exposure Type of EUT: HSPA+ Module FCC ID: RHZDTL718-W Manufacturer: AnyDATA Shanghai Co., Ltd Model: DTL718-W Maximum conducted output power (measured) and antenna Gain: According to section 1.1310 of FCC 47 CFR Part 1, limits for maximum permissible exposure (MPE) are as following Band Maximum Average Conducted Output Power (dBm) Antenna Gain (dBi) UMTS Band II 23.35 4.5 UMTS Band V 23.32 4.5 TA Technology (Shanghai)Co.,Ltd. Test Report Report No.: RXA1211-1096MPE01R1 Page 3 of 5 Note1. Occupational/controlled limits apply in situations in which persons are exposed as a consequence of their employment provided those persons are fully aware of the potential for exposure and can exercise control over their exposure. Limits for occupational/controlled exposure also apply in situations when an individual is transient through a location where occupational / controlled limits apply provided he or she is made aware of the potential for exposure. Note2: General population/uncontrolled exposures apply in situations in which the general public may be exposed, or in which persons that are exposed as a consequence of their employment may not be fully aware of the potential for exposure or can not exercise control over their exposure. The maximum permissible exposure for 300~1500MHz is f/1500, 1500~100,000MHz is f/1500.So Band The maximum permissible exposure WCDMA Band II 1 mW/cm² WCDMA Band V 0.56 mW/cm² TA Technology (Shanghai)Co.,Ltd. Test Report Report No.: RXA1211-1096MPE01R1 Page 4 of 5 IMPORTANT NOTE: To comply with the FCC RF exposure compliance requirements, the antenna(s) used for this transmitter must be installed to provide a separation distance of at least 20 cm from all persons and must not be co-located or operating in conjunction with any other antenna or transmitter. No change to the antenna or the device is permitted. Any change to the antenna or the device could result in the device exceeding the RF exposure requirements and void user’s authority to operate the device. TA Technology (Shanghai)Co.,Ltd. Test Report Report No.: RXA1211-1096MPE01R1 Page 5 of 5 RF Exposure Calculations: The following information provides the minimum separation distance for the highest gain antenna provided. This calculation is based on the conducted power, considering maximum power and antenna gain. The formula shown in OET Bulletin 65 is used in the calculation. Equation from OET Bulletin 65, Edition 97-01 is: S= PG / 4∏R 2 where: S = power density (in appropriate units, e.g. mW/cm 2 ) P = power input to the antenna (in appropriate units, e.g., mW) G = power gain of the antenna in the direction of interest relative to an isotropic radiator R = distance to the center of radiation of the antenna (appropriate units, e.g., cm) UMTS Band II: PG = 23.35dBm+(4.5dBi)=27.85dBm=609.54 mW=0.610 W UMTS Band V PG = 23.32dBm+(4.5dBi)=27.82dBm=605.34 mW=0.605 W R =20 cm ∏= 3.1416 Solving for S, the power density at 20 cm is Band Test Result (mW/cm 2 ) Limit Value (mW/cm 2 ) UMTS Band II 0.1214 1 mW/cm² UMTS Band V 0.1204 0.56 mW/cm² Note: For mobile or fixed location transmitters, minimum separation distance is 20cm, even if calculations indicate MPE distance is less. This means that according to OET Bulletin 65 (Edition 97-01), Supplement C (Edition 01-01), the equipment fulfills the requirements on power density for general population/uncontrolled exposure and therefore fulfills the requirements of 47 CFR Part 15.247 (b) (5)

Report No.: RXA1211-1096RF01R1 Page 1of 40 TESTING No. L2264 Part 22 TEST REPORT Product Name HSPA+ Module Model Name DTL718-W FCC ID RHZDTL718-W Client AnyDATA Shanghai Co., Ltd TA Technology (Shanghai) Co., Ltd. TA Technology (Shanghai) Co., Ltd. Test Report Report No.: RXA1211-1096RF01R1 Page 2of 40 GENERAL SUMMARY Product Name HSPA+ Module Model Name DTL718-W FCC ID RHZDTL718-W Report No. RXA1211-1096RF01R1 Client AnyDATA Shanghai Co., Ltd Manufacturer AnyDATA Shanghai Co., Ltd Reference Standard(s) FCC CFR47 Part 2 (2012-12) Frequency Allocations And Radio Treaty Matters; General Rules And Regulations FCC CFR 47 Part 22H (2012-12) Public Mobile Services(850MHz) ANSI/TIA-603-C(2004) Land mobile FM or PM Communications Equipment Measurements and Performance Standards. KDB 412172 D01 Determining ERP and EIRP v01 Guidelines for Determining the Effective Radiated Power (ERP) and Equivalent Isotropically Radiated Power (EIRP) of a RF Transmitting System Conclusion This portable wireless equipment has been measured in all cases requested by the relevant standards. Test results in Chapter 2 of this test report are below limits specified in the relevant standards. General Judgment: Pass (Stamp) Date of issue: January 18 th , 2013 Comment The test result only responds to the measured sample. Approved by Director Revised by RF Manager Performed by RF Engineer TA Technology (Shanghai) Co., Ltd. Test Report Report No.: RXA1211-1096RF01R1 Page 3of 40 TABLE OF CONTENT 1. General Information ..................................................................................................................... 4 1.1. Notes of the test report.........................................................................................................4 1.2. Testing laboratory .................................................................................................................5 1.3. Applicant Information ............................................................................................................5 1.4. Manufacturer Information ......................................................................................................5 1.5. Information of EUT................................................................................................................6 1.6. Test Date ..............................................................................................................................6 2. Test Information ........................................................................................................................... 7 2.1. Summary of test results ........................................................................................................7 2.2. RF Power Output ..................................................................................................................8 2.3. Effective Radiated Power....................................................................................................10 2.4. Occupied Bandwidth...........................................................................................................13 2.5. Band Edge Compliance......................................................................................................19 2.6. Frequency Stability .............................................................................................................24 2.7. Spurious Emissions at Antenna Terminals .........................................................................26 2.8. Radiates Spurious Emission ...............................................................................................33 3. Main Test Instruments.......................................................................................................... ...... 38 ANNEX A: EUT Appearance and Test Setup.................................................................................... 39 A.1 EUT Appearance ................................................................................................................39 A.2 Test Setup ..........................................................................................................................40 TA Technology (Shanghai) Co., Ltd. Test Report Report No.: RXA1211-1096RF01R1 Page 4of 40 1. General Information 1.1. Notes of the test report TA Technology (Shanghai) Co., Ltd. has obtained the accreditation of China National Accreditation Service for Conformity Assessment (CNAS), and accreditation number: L2264. TA Technology (Shanghai) Co., Ltd. has been listed on the US Federal Communications Commission list of test facilities recognized to perform electromagnetic emissions measurements. The site recognition number is 428261. TA Technology (Shanghai) Co., Ltd. has been listed by industry Canada to perform electromagnetic emission measurement. The site recognition number is 8510A. TA Technology (Shanghai) Co., Ltd. guarantees the reliability of the data presented in this test report, which is the results of measurements and tests performed for the items under test on the date and under the conditions stated in this test report and is based on the knowledge and technical facilities available at TA Technology (Shanghai) Co., Ltd. at the time of execution of the test. TA Technology (Shanghai) Co., Ltd. is liable to the client for the maintenance by its personnel of the confidentiality of all information related to the items under test and the results of the test. This report only refers to the item that has undergone the test. This report standalone dose not constitute or imply by its own an approval of the product by the certification Bodies or competent Authorities. This report cannot be used partially or in full for publicity and/or promotional purposes without previous written approval of TA Technology (Shanghai) Co., Ltd. and the Accreditation Bodies, if it applies. If the electrical report is inconsistent with the printed one, it should be subject to the latter. TA Tech…

Text truncated - open the document above for the full version.

Report No.: RXA1211-1096RF02 Page 1of 39 TESTING No. L2264 Part 24 TEST REPORT Product Name HSPA+ Module Model Name DTL718-W FCC ID RHZDTL718-W Client AnyDATA Shanghai Co., Ltd TA Technology (Shanghai) Co., Ltd. TA Technology (Shanghai) Co., Ltd. Test Report Registration Num: 428261 Report No.: RXA1211-1096RF02 Page 2of 39 GENERAL SUMMARY Product Name HSPA+ Module Model Name DTL718-W FCC ID RHZDTL718-W Report No. RXA1211-1096RF02 Client AnyDATA Shanghai Co., Ltd Manufacturer AnyDATA Shanghai Co., Ltd Reference Standard(s) FCC CFR47 Part 2 (2012-12) Frequency Allocations And Radio Treaty Matters; General Rules And Regulations FCC CFR47 Part 24E (2012-12) Personal Communications Services ANSI/TIA-603-C(2004) Land mobile FM or PM Communications Equipment Measurements and Performance Standards. KDB 412172 D01 Determining ERP and EIRP v01 Guidelines for Determining the Effective Radiated Power (ERP) and Equivalent Isotropically Radiated Power (EIRP) of a RF Transmitting System Conclusion This portable wireless equipment has been measured in all cases requested by the relevant standards. Test results in Chapter 2 of this test report are below limits specified in the relevant standards. General Judgment: Pass (Stamp) Date of issue: January 18 th , 2013 Comment The test result only responds to the measured sample. Approved by Director Revised by RF Manager Performed by RF Engineer TA Technology (Shanghai) Co., Ltd. Test Report Registration Num: 428261 Report No.: RXA1211-1096RF02 Page 3of 39 TABLE OF CONTENT 1. General Information ..................................................................................................................... 4 1.1. Notes of the test report.........................................................................................................4 1.2. Testing laboratory .................................................................................................................5 1.3. Applicant Information ............................................................................................................5 1.4. Manufacturer Information ......................................................................................................5 1.5. Information of EUT................................................................................................................6 1.6. Test Date ..............................................................................................................................6 2. Test Information ........................................................................................................................... 7 2.1. Summary of test results ........................................................................................................7 2.2. RF Power Output ..................................................................................................................7 2.3. Effective Isotropic Radiated Power .....................................................................................10 2.4. Occupied Bandwidth...........................................................................................................13 2.5. Band Edge Compliance......................................................................................................19 2.6. Frequency Stability .............................................................................................................24 2.7. Spurious Emissions at Antenna Terminals .........................................................................26 2.1. Radiates Spurious Emission ...............................................................................................33 3. Main Test Instruments .......................................................................................................... ...... 37 ANNEX A: EUT Appearance and Test Setup..................................................................................... 38 A.1 EUT Appearance ................................................................................................................38 A.2 Test Setup ...........................................................................................................................39 TA Technology (Shanghai) Co., Ltd. Test Report Registration Num: 428261 Report No.: RXA1211-1096RF02 Page 4of 39 1. General Information 1.1. Notes of the test report TA Technology (Shanghai) Co., Ltd. has obtained the accreditation of China National Accreditation Service for Conformity Assessment (CNAS), and accreditation number: L2264. TA Technology (Shanghai) Co., Ltd. has been listed on the US Federal Communications Commission list of test facilities recognized to perform electromagnetic emissions measurements. The site recognition number is 428261. TA Technology (Shanghai) Co., Ltd. has been listed by industry Canada to perform electromagnetic emission measurement. The site recognition number is 8510A. TA Technology (Shanghai) Co., Ltd. guarantees the reliability of the data presented in this test report, which is the results of measurements and tests performed for the items under test on the date and under the conditions stated in this test report and is based on the knowledge and technical facilities available at TA Technology (Shanghai) Co., Ltd. at the time of execution of the test. TA Technology (Shanghai) Co., Ltd. is liable to the client for the maintenance by its personnel of the confidentiality of all information related to the items under test and the results of the test. This report only refers to the item that has undergone the test. This report standalone dose not constitute or imply by its own an approval of the product by the certification Bodies or competent Authorities. This report cannot be used partially or in full for publicity and/or promotional purposes without previous written approval of TA Technology (Shanghai) Co., Ltd. and the Accreditation Bodies, if it applies. If the electrical report is inconsistent …

Text truncated - open the document above for the full version.

DTL718-W FCC test setup photo 1. RSE